Search NASA⌕ Search

SEARCH · Search NASA

Results for “high performance computing systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Analytical Investigation of an Adaptive Flight-Control System Using a Sinusoidal Test Signal

An analytical study was made of an adaptive flight-control system which measures vehicle response to small-amplitude control-surface deflections produced by a sinusoidal test signal. Changes in the response to this signal are related to environmental changes,, and the system is continuously altered to maintain this response equal to a preselected value. The system is suitable for use in high-performance aircraft and missiles and requires only the addition of a signal generator and a logic circuit consisting of a filter-rectifier network and a comparator-integrator network to a basic command-control system. Thus, it presents a relatively simple approach to the problem. The effects on system performance of variation in flight condition, system-gain level, test-signal frequency, and sensor location are included in the analysis. Longitudinal control of a high-performance research aircraft over flight conditions ranging from landing approach to a Mach number of 5.8 at an altitude of 150,000 feet, and longitudinal control of a four-stage solid-fuel missile including the first bending mode over the atmospheric portion of a launch trajectory constituted the basis for the analytical study. Results of an analog-computer study using time-varying coefficients are presented to compare the control obtained with the adaptive system with-that obtained with a fixed-gain system during the atmospheric portion of a missile launch trajectory. The system has demonstrated an ability to maintain satisfactory vehicle control-system stability over wide ranges of environmental change.

Harris, Jack E.↗

Seeing the forest for the trees: Networked workstations as a parallel processing computer

Unlike traditional 'serial' processing computers in which one central processing unit performs one instruction at a time, parallel processing computers contain several processing units, thereby, performing several instructions at once. Many of today's fastest supercomputers achieve their speed by employing thousands of processing elements working in parallel. Few institutions can afford these state-of-the-art parallel processors, but many already have the makings of a modest parallel processing system. Workstations on existing high-speed networks can be harnessed as nodes in a parallel processing environment, bringing the benefits of parallel processing to many. While such a system can not rival the industry's latest machines, many common tasks can be accelerated greatly by spreading the processing burden and exploiting idle network resources. We study several aspects of this approach, from algorithms to select nodes to speed gains in specific tasks. With ever-increasing volumes of astronomical data, it becomes all the more necessary to utilize our computing resources fully.

Breen, J. O.↗

Effect of scanline orientation on ventricular flow propagation: assessment using high frame-rate color Doppler echocardiography

Color M-mode echocardiography has recently been utilized to describe diastolic flow propagation velocity (Vp) in the left ventricle. While increasing temporal resolution from 15 to 200 Hz, this M-mode technique requires the user to select a single scanline, potentially limiting quantification of Vp due to the complex three-dimensional inflow pattern. We previously performed computational fluid dynamics simulations to demonstrate the insignificance of the scanline orientation, however geometric complexity was limited. The purpose of this study was to utilize high frame-rate 2D color Doppler images to investigate the importance of scanline selection in patients for the quantification of Vp. 2D color Doppler images were digitally acquired at 50 frames/s in 6 subjects from the apical 4-chamber window (System 5, GE/Vingmed, Milwaukee, WI). Vp was determined for a set of scanlines positioned through 5 locations across the mitral annulus (from the anterior to posterior mitral annulus). An analysis of variance was performed to examine the differences in Vp as a function of scanline position. Vp was not effected by scanline position in sampled locations from the center of the mitral valve towards the posterior annulus. Although not statistically significant, there was a trend to slower propagation velocities on the anterior side of the valve (60.8 +/- 16.7 vs. 54.4 +/- 13.6 cm/s). This study clinically validates our previous numerical experiment showing that Vp is insensitive to small perturbations of the scanline through the mitral valve. However, further investigation is necessary to examine the impact of ventricular geometry in pathologies including dilated cardiomyopathy.

Non-NASA Center↗

Scramjet nozzle design and analysis as applied to a highly integrated hypersonic research airplane

The configuration and performance of the propulsion system for the hypersonic research vehicle are discussed. A study of the interactions between propulsion and aerodynamics of the highly integrated vehicle was conducted. The hypersonic research vehicle is configured to test the technology of structural and thermal protection systems concepts and the operation of the propulsion system under true flight conditions for most of the hypersonic flight regime. The subjects considered are: (1) research vehicle and scramjet engine configurations to determine fundamental engine sizing constraints, (2) analytical methods for computing airframe and propulsion system components, and (3) characteristics of a candidate nozzle to investigate vehicle stability and acceleration performance.

Small, W. J.↗

Robonaut's Flexible Information Technology Infrastructure

Robonaut, NASA's humanoid robot, is designed to work as both an astronaut assistant and, in certain situations, an astronaut surrogate. This highly dexterous robot performs complex tasks under telepresence control that could previously only be carried out directly by humans. Currently with 47 degrees of freedom (DOF), Robonaut is a state-of-the-art human size telemanipulator system. while many of Robonaut's embedded components have been custom designed to meet packaging or environmental requirements, the primary computing systems used in Robonaut are currently commercial-off-the-shelf (COTS) products which have some correlation to flight qualified computer systems. This loose coupling of information technology (IT) resources allows Robonaut to exploit cost effective solutions while floating the technology base to take advantage of the rapid pace of IT advances. These IT systems utilize a software development environment, which is both compatible with COTS hardware as well as flight proven computing systems, preserving the majority of software development for a flight system. The ability to use highly integrated and flexible COTS software development tools improves productivity while minimizing redesign for a space flight system. Further, the flexibility of Robonaut's software and communication architecture has allowed it to become a widely used distributed development testbed for integrating new capabilities and furthering experimental research.

Askew, Scott↗

Computerized optimal control system design for reusable and expendable boost vehicles.

An optimization technique has been developed which combines the practical features of hybrid simulation of the dynamic system under study with the systematic approach of modern control theory where a mathematically formulated design criterion is optimized by functional minimization. Standard hybrid computer optimization methods using high-speed repetitive simulations and gradient minimization schemes have been extended to obtain time-varying optimal gain schedules and reduce the sensitivity of the optimized system to parameter and disturbance uncertainties. In this approach the performance index is expressed in meaningful engineering terms that reflect the interactions among all major disciplines, structures, control/actuation system design, aerodynamics and performance. The basic optimization technique is developed and its application to current aerospace control problems including the space shuttle is presented in detail. In the discussion of the application, the controllers resulting from the technique are compared with controllers developed by conventional methods. The paper concludes with a review of the advantages and disadvantages of the technique and plans for future applications.

Connor, C. L.↗

Flexible body stability analysis of Space Shuttle ascent flight control system by using lambda matrix solution techniques

A lambda matrix solution technique is being developed to perform an open loop frequency analysis of a high order dynamic system. The procedure evaluates the right and left latent vectors corresponding to the respective latent roots. The latent vectors are used to evaluate the partial fraction expansion formulation required to compute the flexible body open loop feedback gains for the Space Shuttle Digital Ascent Flight Control System. The algorithm is in the final stages of development and will be used to insure that the feedback gains meet the design specification.

Bown, R. L.↗

Experimental evaluation of the concept of supevisory manipulation

A computer-controlled teleoperator system which is based on task-referenced sensor-aided control has been developed to study supervisory manipulation. This system, called SUPERMAN, is capable of performing complicated tasks in real-time by utilizing the operator for high-level functions related to the unpredictable portions of a task, while the subordinate machine performs the more well-defined subtasks under human supervison. To determine whether supervisory control schemes such as these offer any advantage over manual control under real-time conditions, a number of experiments involving both simple and complicated tasks were performed. Six representative tasks were chosen for the study: (1) obtaining a tool from a rack, (2) returning the tool to the rack, (3) removing a nut, (4) placing samples in a storage bin, (5) opening and closing a valve, and (6) digging with a shovel. The experiments were performed under simulated conditions using four forms of manual control (i.e., switch rate, joystick rate, master-slave position control, and master-slave with force feedback), as well as supervisory control. Through these experiments the effectiveness and quality of control were evaluated on the basis of the time required to complete each portion of the task and the type and number of errors which occurred.

Brooks, T. L.↗

Analysis, design, and testing of a low cost, direct force command linear proof mass actuator for structural control

In this paper, the design, analysis, and test of a low cost, linear proof mass actuator for vibration control is presented. The actuator is based on a linear induction coil from a large computer disk drive. Such disk drives are readily available and provide the linear actuator, current feedback amplifier, and power supply for a highly effective, yet inexpensive, experimental laboratory actuator. The device is implemented as a force command input system, and the performance is virtually the same as other, more sophisticated, linear proof mass systems.

Slater, G. L.↗

NCC: A Multidisciplinary Design/Analysis Tool for Combustion Systems

A multi-disciplinary design/analysis tool for combustion systems is critical for optimizing the low-emission, high-performance combustor design process. Based on discussions between NASA Lewis Research Center and the jet engine companies, an industry-government team was formed in early 1995 to develop the National Combustion Code (NCC), which is an integrated system of computer codes for the design and analysis of combustion systems. NCC has advanced features that address the need to meet designer's requirements such as "assured accuracy", "fast turnaround", and "acceptable cost". The NCC development team is comprised of Allison Engine Company (Allison), CFD Research Corporation (CFDRC), GE Aircraft Engines (GEAE), NASA Lewis Research Center (LeRC), and Pratt & Whitney (P&W). This development team operates under the guidance of the NCC steering committee. The "unstructured mesh" capability and "parallel computing" are fundamental features of NCC from its inception. The NCC system is composed of a set of "elements" which includes grid generator, main flow solver, turbulence module, turbulence and chemistry interaction module, chemistry module, spray module, radiation heat transfer module, data visualization module, and a post-processor for evaluating engine performance parameters. Each element may have contributions from several team members. Such a multi-source multi-element system needs to be integrated in a way that facilitates inter-module data communication, flexibility in module selection, and ease of integration.

Liu, Nan-Suey↗

Code Optimization and Parallelization on the Origins: Looking from Users' Perspective

Parallel machines are becoming the main compute engines for high performance computing. Despite their increasing popularity, it is still a challenge for most users to learn the basic techniques to optimize/parallelize their codes on such platforms. In this paper, we present some experiences on learning these techniques for the Origin systems at the NASA Advanced Supercomputing Division. Emphasis of this paper will be on a few essential issues (with examples) that general users should master when they work with the Origins as well as other parallel systems.

Chang, Yan-Tyng Sherry↗

Design of the Cruise and Flap Airfoil for the X-57 Maxwell Distributed Electric Propulsion Aircraft

A computational and design study on an airfoil and high-lift flap for the X-57 Maxwell Distributed Electric Propulsion (DEP) testbed aircraft was conducted. The aircraft wing sizing study resulted in a wing area of 66.67 sq ft and aspect ratio of 15 with a design requirement of V(stall) = 58 KEAS, at a gross weight of 3,000 lb. To meet this goal an aircraft C(L,max) of 4.0 was required. The design cruise condition is 150 KTAS at 8,000 ft. This resulted in airfoil requirements of c(l) is approximately 0.90 for the cruise condition at Re = 2.35 x 10 (exp 6). A flapped airfoil with a c(l,max) of approximately 2.5 or greater, at Re = 1.0 x 10 (exp 6), was needed to have enough lift to meet the stall requirement with the DEP system. MSES computational analyses were conducted on the GAW-1, GAW-2, and the NACA 5415 airfoil sections, however they had limitations in either high drag or low c(l,max) on the cruise airfoil, which was the impetus for a new design. A design was conducted to develop a low drag airfoil for the X-57 cruise conditions with high c(l,max). The final design was the GNEW5BP93B airfoil with a minimum drag coefficient of c(d) = 0.0053 at c(l) = 0.90 and achieved laminar flow back to 69% chord on the upper surface and 62% chord on the lower surface. With fully turbulent flow, the drag increases to c(d) = 0.0120. The predicted maximum lift with turbulent flow is a c(l,max) of 1.95 at alpha = 19 deg. The airfoil is characterized by relatively flat pressure gradient regions on both surfaces at alpha = 0 deg, and aft camber to get extra lift out of the lower surface concave region. A 25% chord slotted flap was designed and analyzed with MSES for a 30 deg flap deflection. Additional 30 deg and 40 deg flap deflection analyses for two flap positions were conducted with USM3D using several turbulence models, for two angles of attack, to assess near c(l,max) with varied flap position. The maximum c(l) varied between 2.41 and 3.35. An infinite-span powered high-lift study was conducted on a GAW-1 constant chord 40 deg flapped airfoil section with FUN3D to quantify the airfoil lift increment that can be expected from a DEP system. The 16.7 hp/propeller blown wing increases the maximum C(L) from 3.45 to C(L) = 6.43, which is an effective q ratio of 1.86. This indicates that if the unblown high-lift flapped airfoil of the X-57 airplane achieves a c(l,max) of 2.78, then the high-lift augmentation blowing could yield a sectional lift coefficient of approximately 4.95 at c(l,max). Finally, a computational study was conducted with FUN3D on an infinite-span constant chord GAW-1 cruise airfoil to determine the impact of high-lift propeller diameter to wing chord ratio on the lift increment of the DEP system. A constant diameter propeller and nacelle size were used in the study. Three computational grids were made with airfoil chords of 0.5*chord, 1.0*chord, and 2.0*chord. Results of the propeller diameter to wing chord ratio study indicated that the blown to unblown C(L) ratio increased as the chord was decreased. However, because of the increase in relative size of the high-lift nacelle to the wing, which impacted wing lift performance, the study indicated that a propeller diameter to wing chord ratio of 1.0 gives the overall best maximum lift on the wing with the DEP system.

Viken, Jeffrey K.↗

The prediction of nozzle performance and heat transfer in hydrogen/oxygen rocket engines with transpiration cooling, film cooling, and high area ratios

An advanced engineering computational model has been developed to aid in the analysis and design of hydrogen/oxygen chemical rocket engines. The complete multi-species, chemically reacting and diffusing Navier-Stokes equations are modelled, finite difference approach that is tailored to be conservative in an axisymmetric coordinate system for both the inviscid and viscous terms. Demonstration cases are presented for a 1030:1 area ratio nozzle, a 25 lbf film cooled nozzle, and transpiration cooled plug-and-spool rocket engine. The results indicate that the thrust coefficient predictions of the 1030:1 nozzle and the film cooled nozzle are within 0.2 to 0.5 percent, respectively, of experimental measurements when all of the chemical reaction and diffusion terms are considered. Further, the model's predictions agree very well with the heat transfer measurements made in all of the nozzle test cases. The Soret thermal diffusion term is demonstrated to have a significant effect on the predicted mass fraction of hydrogen along the wall of the nozzle in both the laminar flow 1030:1 nozzle and the turbulent plug-and-spool rocket engine analysis cases performed. Further, the Soret term was shown to represent a significant fraction of the diffusion fluxes occurring in the transpiration cooled rocket engine.

Kacynski, Kenneth J.↗

NASA SPLICE Project: Development and Testing of Precision Landing GN&C Technologies

NASA's technology advancement needs for entry, descent and landing call for high-precision, high-rate sensors that can improve navigation accuracy and vehicle control performance. Higher landing accuracy is required for any future human lander missions, and likely, for most robotic missions 1,2. Sensors and algorithms that significantly reduce navigation errors and can image the local terrain will enable landing at locations of high scientific interest that would otherwise pose significant risk to the vehicle. The Safe and Precise Landing-Integrated Capabilities Evolution project, or SPLICE, is developing precision landing and hazard avoidance (PL&HA) technologies for NASA and for potential commercial space flight missions. SPLICE technologies include sensors, algorithms, advanced space flight computing capabilities, and simulation tools used to integrate and study guidance, navigation, and control (GN&C) system performance. SPLICE efforts include hardware-in-the-loop (HWIL) simulation testing, ground testing, and flight testing, including reuse of hardware from the CoOperative Blending of Autonomous Landing Technologies (COBALT) suborbital flight-test payload3,4. Two of the precise navigation sensors that are being developed and matured within SPLICE are LiDARs. Since 2006, NASA Langley has been developing a Navigation Doppler LiDAR (NDL) for precise velocity measurements, and SPLICE is building an NDL engineering test unit (ETU) that will be brought up to TRL 6 following environmental and high-speed1,2 testing. NASA Goddard is developing a Hazard Detection LiDAR (HD LiDAR) engineering development unit (EDU) for SPLICE that has relevance to future human and robotic lander missions. The HD LiDAR will be flight test and matured to TRL 5.

Restrepo, Carolina I.↗

Validation of a Computational Model for the SLS Core Stage Oxygen Tank Diffuser Concept and the Low Profile Diffuser - An Advanced Development Design for the SLS

The Low Profile Diffuser (LPD) project originated as an award from the Marshall Space Flight Center (MSFC) Advanced Development (ADO) office to the Main Propulsion Systems Branch (ER22). The task was created to develop and test an LPD concept that could produce comparable performance to a larger, traditionally designed, ullage gas diffuser while occupying a smaller volume envelope. Historically, ullage gas diffusers have been large, bulky devices that occupy a significant portion of the propellant tank, decreasing the tank volume available for propellant. Ullage pressurization of spacecraft propellant tanks is required to prevent boil-off of cryogenic propellants and to provide a positive pressure for propellant extraction. To achieve this, ullage gas diffusers must slow hot, high-pressure gas entering a propellant tank from supersonic speeds to only a few meters per second. Decreasing the incoming gas velocity is typically accomplished through expansion to larger areas within the diffuser which has traditionally led to large diffuser lengths. The Fluid Dynamics Branch (ER42) developed and applied advanced Computational Fluid Dynamics (CFD) analysis methods in order to mature the LPD design from and initial concept to an optimized test prototype and to provide extremely accurate pre-test predictions of diffuser performance. Additionally, the diffuser concept for the Core Stage of the Space Launch System (SLS) was analyzed in a short amount of time to guide test data collection efforts of the qualification of the device. CFD analysis of the SLS diffuser design provided new insights into the functioning of the device and was qualitatively validated against hot wire anemometry of the exterior flow field. Rigorous data analysis of the measurements was performed on static and dynamic pressure data, data from two microphones, accelerometers and hot wire anemometry with automated traverse. Feasibility of the LPD concept and validation of the computational model were demonstrated by the test data.

Brodnick, Jacob↗

Modeling Deformable Linear Objects for Autonomous Robotic Outfitting of Lunar Surface Systems

This paper presents structural models of deformable linear objects (DLOs). DLOs are a subclass of deformable objects that encompasses common outfitting elements such as cables and ropes. Models are validated through hardware experiments, and integration in a robotic autonomy architecture for space environments is discussed. A persistent human presence on the lunar surface is one of the next major milestones in space exploration. This requires the development of robust extraplanetary construction technologies including structures and materials modeling and robotic systems. Previous robotic construction technology development has primarily focused on structural assembly, with significantly less focus on robotically performed outfitting tasks to instantiate subsystems providing power, data, life support, etc. These tasks involve manipulation of highly flexible elements, which are difficult to model, such as cable harnesses, ropes, and hoses. Robotic manipulation of DLOs, especially cable harnesses, is an active area of research as cable harnesses are essential for providing power and data to space assets. DLO models that can be used for robot manipulator trajectory generation are necessary for autonomous operation of lunar infrastructure. There are many proposed methods for modeling DLOs, and they primarily fall into three types: 1) discrete model-based, 2) continuum model-based, and 3) Neural Network-based. These types each have pros and cons, and the tradeoff between model accuracy and computational speed informs which type should be used. An understanding of this trade-off is imperative for real-time control of autonomous systems. High computational requirements reduce the speed of the model, making real-time control difficult, while accuracy is critical to preventing collisions. Discrete models, such as a mass-spring multibody representation, require relatively few calculations, and accuracy is directly tied to the step size of the discretization. Continuum models, such as a B-spline representation or a Cosserat rod model (a mix of continuous and discrete), are more informed of the structural properties of the cable and are much more accurate than a rigid body mass-spring model, but at significant computational cost. A Neural Network approach can provide an online solution with very few computational steps, but properly generating training data can be difficult and validation for an in-space application is not trivial. This paper explores the trade-off between different modeling approaches and compares accuracy and computational speed/complexity of the three types mentioned above. Model accuracy is evaluated using a cable in a static configuration. True cable shape is obtained using a depth camera for RGB images and point-cloud segmentation. The purpose of this experiment is to evaluate the trade-offs of different approaches to the DLO modeling problem. Understanding the tradeoffs between different cable modeling techniques paves the way for developing robotic control and planning architectures necessary for real-time manipulation of DLOs for lunar infrastructure outfitting. Real-time control is required for robotic systems to be able to actively manipulate a cable in a harsh environment where model and sensor errors compound, and environmental conditions can cause significant disturbances. Cable routing must be performed in areas with high density of objects/obstacles: through truss structures, near solar panels or mirror arrays, next to bundles of electrical equipment. Understanding the best way to plan and manipulate a cable without disrupting the environment or damaging the cable is imperative to robotic outfitting operations on the lunar surface.

Amy M Quartaro↗

Postbuckling and large-deflection nonlinear analyses on distributed-memory computers

A computational strategy is presented for postbuckling and nonlinear static analyses of large complex structures on distributed-memory parallel computers. The strategy is designed for message-passing parallel computer systems. The key elements of the proposed strategy are: (1) a multiple-parameter reduced basis technique; (2) a nested dissection (or multilevel substructuring) ordering scheme; (3) parallel assembly of global matrices; and (4) a parallel sparse equation solver. The effectiveness of the strategy is assessed by performing thermomechanical postbuckling analyses of stiffened composite panels with cutouts, and nonlinear large-deflection analyses of High Speed Civil Transport models on three distributed-memory computers. The numerical studies presented demonstrate the advantages of nested dissection-based solvers over traditional skyline-based solvers on distributed-memory machines.

Watson, Brian C.↗

The NASA Science Internet: An integrated approach to networking

An integrated approach to building a networking infrastructure is an absolute necessity for meeting the multidisciplinary science networking requirements of the Office of Space Science and Applications (OSSA) science community. These networking requirements include communication connectivity between computational resources, databases, and library systems, as well as to other scientists and researchers around the world. A consolidated networking approach allows strategic use of the existing science networking within the Federal government, and it provides networking capability that takes into consideration national and international trends towards multivendor and multiprotocol service. It also offers a practical vehicle for optimizing costs and maximizing performance. Finally, and perhaps most important to the development of high speed computing is that an integrated network constitutes a focus for phasing to the National Research and Education Network (NREN). The NASA Science Internet (NSI) program, established in mid 1988, is structured to provide just such an integrated network. A description of the NSI is presented.

Rounds, Fred↗