Search NASA⌕ Search

SEARCH · Search NASA

Results for “influence”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Influence of phase composition on microstructure and properties of Mg-5Al-0.4Mn-xRE (x = 0, 3 and 5 wt.%) alloys

The microstructure and mechanical properties investigations of two AME503 and AME505 experimental alloys in as-cast conditions were presented. The investigated materials were fabricated on the basis of the AM50 commercial magnesium alloy with 3 and 5 wt.% cerium rich mischmetal. In the as-cast condition, both experimental alloys were mainly composed of α-Mg, Al{sub 11}RE{sub 3} and Al{sub 10}RE{sub 2}Mn{sub 7} intermetallic phases. Additionally, due to non-equilibrium solidification conditions, a small amount of α + γ divorced eutectic and Al{sub 2}RE intermetallic phase were revealed. The obtained results also show a significant influence of rare earth elements on Brinell hardness, tensile and compression properties at ambient temperature and especially on creep properties at 473 K. Improved alloy properties with a rise in rare earth elements mass fraction results from an increase in Al{sub 11}RE{sub 3} phase volume fraction and suppression of α + γ eutectic volume fraction in the alloy microstructure. Additionally, the influence of rare earth elements on the dendrite arm space value was discussed. The presented results also proved the thermal stability of the intermetallic phases during creep testing. - Highlights: • Two different Mg-5Al-0.4Mn alloys containing 3 and 5 wt.% of rare earth elements were fabricated. • Addition of rare earth elements leads to a reduction of dendrite arm spaces. • Mechanical properties depend on the phase composition of the alloys. • The increase of the rare earth elements content causes rise of the creep resistance.

36 MATERIALS SCIENCE↗

Influence of quenching agent on microstructure, properties and thermal stress of SiC{sub p}/2009 composites

15% vol. SiC{sub p}/2009 composites prepared by powder metallurgy were quenched in room temperature water and 20% polyethylene glycol (PEG) solution respectively, then aged naturally. The influence of quenching agent on microstructure, properties and thermal stress of SiC{sub p}/2009 composites were investigated by means of scanning/transmission electron microscope, hardness and tensile test. The results showed that the number of precipitated phase in water quenched composites increased, with much finer in size and more homogeneous in distribution compared with 20% PEG quenched one. Meanwhile, the density of dislocation in composites by water quenching was also much higher. Intergranular corrosion did not occur with the two quenching agents. The 20% PEG quenched composites exhibited slight lower hardness and higher electrical conductivity than that of water quenched one. The two quenched composites showed same level in tensile strength, but the yield strength of water-quenched composites was higher (8 MPa, 3%). The usage of 20% PEG reduced thermal stress and minimized warping deformation of the parts, it is a more suitable quenching agent for SiC{sub p}/2009 composites in engineering application fields. - Highlights: •SiC{sub p}/2009 composites quenched by water and 20% PEG solution were investigated. •Aging precipitation behavior of SiC{sub p}/2009 composites is sensitive to quenchant. •Influence of quenching agent on properties of SiC{sub p}/2009 composites are minimal. •Quenching with 20% PEG reduces thermal stress of SiC{sub p}/2009 composites remarkably. •20% PEG is a more suitable quenching agent for SiC{sub p}/2009 composites than water.

36 MATERIALS SCIENCE↗

Influence of severe plastic deformation on intermetallic particles in Mg-12 wt.%Zn alloy investigated using transmission electron microscopy

The in-depth microstructural characterization of intermetallic particles in an Mg-12 wt.%Zn binary alloy subjected to a severe plastic deformation is presented. The alloy was processed by four passes via equal channel angular pressing with an applied back pressure at a gradually decreasing temperature and analyzed using transmission electron microscopy techniques to observe the influence of processing on intermetallic particles. The results are compared with the initial state of the material prior to severe plastic deformation. The microstructural evolution of the α-Mg matrix and the Mg{sub 21}Zn{sub 25}, Mg{sub 51}Zn{sub 20} and MgZn{sub 2} was analyzed using bright field imaging, selected area electron diffraction, high-resolution transmission electron microscopy and high-angle annular dark field imaging in scanning mode. The plastic deformation process influenced the α-Mg matrix and each type of intermetallic particle. The α-Mg matrix consisted of two types of areas. The first type of area had a highly deformed structure, and the second type of area had a partially recrystallized structure with an average grain size of approximately 250 nm. The Mg{sub 21}Zn{sub 25} microparticles exhibited distinct forms in the α-Mg matrix that were characterized as a single-crystalline form, a nano-crystalline form and a broken up form. No evidence of Mg{sub 51}Zn{sub 20} nanoparticles within the α-Mg matrix was found in the microstructure, which indicates their dissolution or phase transformation during the deformation process. MgZn{sub 2} nanoparticles exhibited different behavior in both types of α-Mg matrix. Two orientation relationships toward the highly deformed α-Mg matrix were observed; however, there was no relationship toward the partially recrystallized α-Mg matrix. Additionally, the growth of the MgZn{sub 2} nanoparticles was different in the two types of α-Mg matrix. The Mg{sub 51}Zn{sub 20} nanoparticles inside Mg{sub 21}Zn{sub 25} microparticles exhibited a distinct behavior within the single-crystalline or nano-crystalline form of the parent Mg{sub 21}Zn{sub 25} microparticles. The Mg{sub 21}Zn{sub 25} + Mg{sub 51}Zn{sub 20} eutectic compound was confirmed for both forms of the parent Mg{sub 21}Zn{sub 25} microparticles, and the growth of Mg{sub 51}Zn{sub 20} nanoparticles is discussed. - Highlights: •Comprehensive microstructure characterization of Mg-12 wt.%Zn alloy after ECAP-BP •TEM analysis of changes of intermetallic phases caused by SPD •Mg{sub 21}Zn{sub 25} particles exhibit nano-crystalline regions with grain size below 100 nm. •MgZn{sub 2} preserved its orientation relationship toward highly deformed α-Mg after SPD. •Existence of Mg{sub 21}Zn{sub 25} + Mg{sub 51}Zn{sub 20} eutectic remained for each Mg{sub 21}Zn{sub 25} particle form.

36 MATERIALS SCIENCE↗

Negative influence of rafted γ′ phases on 750 °C/750 MPa creep in a Ni-based single crystal superalloy with 4% Re addition

Highlights: • The negative influence of the rafted γ′ phases on creep was investigated. • The rafted sample exhibited a lower creep rate a shorter rupture life. • Fine γ′ phases impeded first the dislocation movement in γ matrix. • Existed superdislocations and the stress release decreased the creep resistance. • Rafted γ′ phases were more easily cut by superdislocations and stacking faults. - Abstract: Specimens with two different γ′ phase microstructures, named as-heat treated sample with cuboidal γ′ phases and pre-rafted sample with N-type rafted γ′ phases, were compared to investigate the negative influence of the rafted γ′ phases on the creep property in a Ni-based single crystal superalloy with 4% Re addition at 750 °C and 750 MPa condition. The results indicated that the sample with cuboidal γ′ phases exhibited a lower creep rate and a longer rupture life compared to that with rafted γ′ phases. Transmission electron microscope examinations showed that lots of fine γ′ phases impeded first the dislocation movement in the channel of γ matrix in the initial primary creep stage before the cuboidal γ′ phases were cut by stacking faults in as-heat treated sample. However, in pre-rafted sample, some existed superdislocations located in rafted γ′ phases and the mismatch stress release at γ/rafted γ′ interface resulting from pre-rafted treatment not only decreased the creep resistance of rafted γ′ phases, but also weakened the γ/rafted γ′ interface pinning effect for dislocation movement. Therefore, the rafted γ′ phases were easily cut by superdislocations and stacking faults resulting in a higher creep rate and a shorter creep life.

36 MATERIALS SCIENCE↗

Influence of velocity of pressing in RCS processed AA8090 Al-Li alloy

Highlights: • For the first time the Influence of RCS on the properties of AA 8090 has been studied by processing velocity. • It is found that the properties vary according to pressing velocity and number of passes. • Reported significant property improvement achieved through the pressing velocity of 1.5mm/s. - Abstract: The effect of the velocity of pressing on grain refinement in AA8090 Al-Li alloy sheets during repetitive corrugation and straightening (RCS) at 300 °C is studied. V-groove corrugation dies and flattening dies were used at three different pressing velocities of 1.5 mm/s, 2 mm/s and 2.5 mm/s. The specimen temperature was maintained at 300 °C. Grain refinement was significantly influenced by the pressing velocity. The samples processed for 8 passes at a pressing velocity of 1.5 mm/s had an improved microhardness value of 104 HV and an increased tensile strength of 405 MPa which is respectively 39% and 113% more than the corresponding values in the parent material. TEM analysis showed that samples processed at a pressing velocity of 1.5 mm/s had in places a grain size down to 50 nm and the EBSD results revealed that the average grain size was 2 μm, with 86% of the total number of grain boundaries of the high angle type.

36 MATERIALS SCIENCE↗

Influence of duplex ageing on secondary α precipitates and mechanical properties of the near β-Ti alloy Ti-55531

Highlights: • High strength β-Ti alloys are widely used for their excellent properties. • To reach an excellent combination of strength and ductility, it is attractive to explore the right heat treatment system. • While compared to the conventional single-step ageing process, duplex ageing could change the development and refinement of secondary α precipitations in near/metastable β-Ti alloys resulting varying in performance. • Therefore it is of scientific significance and engineering value to understand the influence of duplex ageing on the formation of secondary α precipitates and mechanical properties for this type of alloy. - Abstract: This paper presents the results of studies on the microstructure and mechanical properties of a near β-Ti alloy processed with different ageing approaches. Influences of intragranular ultrafine α precipitates and grain boundary α layer on mechanical properties in Ti-55531 alloy were analyzed. The results indicate that the precipitation microstructure of the duplex aged alloy exhibits a uniform size and acicular α precipitated orientation shows an angle of approximately 60°. While the morphology of secondary α precipitates in single-step aged samples appear the irregular distribution and heterogeneous size. With the final ageing time increasing, the morphology of intragranular α precipitates and grain boundary α phase brings out a distinct coarsening. The single-step aged alloy can yield a better combination of the ultimate tensile strength (1265 MPa) and ductility (9%). However, the ultimate tensile strength of the duplex aged alloy even reaches 1368 MPa but it breaks at the stage of elastic deformation. The fracture mode of Ti-55531 alloy changes from predominantly dimple fracture in single-step aged samples to predominantly faceted and cleavage type fracture in duplex aged samples causing by the differences of intragranular α precipitates and the interface between grain boundary α layer and intragranular microstructure.

36 MATERIALS SCIENCE↗

Influence of fabrication on microstructure and heat affected zone width in weldments of nuclear reactor pressure vessel steel

Advanced manufacturing routes such as electron beam welding and powder metallurgy with hot isostatic pressing are increasingly used across energy and aerospace industries, where the reliable prediction of weld behavior and heat affected zone (HAZ) evolution is critical. This study examines how fabrication routes and post-weld heat treatments influence phase distribution, crystallite size, microstrain, and dislocation density in nuclear reactor pressure vessel steels using synchrotron X-ray diffraction (SXRD). Retained austenite occurs only in samples that did not undergo austenitization, whereas an austenitizing heat treatment fully eliminates retained austenite and produces a more uniform microstructure across the weldment in terms of phase fraction, dislocation density, and microstrain. The Rosenthal solution underestimates the HAZ width for powder metallurgy samples. A newly proposed modified Rosenthal solution, reducing density by accounting for porosity, matches the SXRD-measured HAZ width with a 0.65% error. Structure–property correlations reveal that dislocation density correlates strongly with nanohardness in homogenous microstructures, while in heterogenous weldments nanohardness is further influenced by the presence of dissimilar phase boundaries. These findings provide new insight into the thermal and microstructural response of powder metallurgy fabricated steels and offer a framework for optimizing welding procedures and heat treatments in advanced manufacturing applications.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Thermal behaviour of NaBH{sub 4}-sodalites with alumosilicate framework: Influence of cage water content and the surrounding conditions

Research highlights: {yields} Thermal behaviour of NaBH{sub 4} enclathrated sodalites with alumosilicate framework. {yields} Influence of mixed cage fillings (H{sub 2}O, H{sub 3}O{sub 2}{sup -}, CO{sub 3}{sup 2-}) on thermal behaviour of BH{sub 4}{sup -}. {yields} Extend of intra cage reactions depend on templates and experimental surroundings. {yields} Formation of B(OH){sub 4}{sup -}/BH{sub 3}OH{sup -}, BO(OH){sub 2}{sup -} and finally BO{sub 2}{sup -} inside the cages. {yields} Formation of nepheline with boron in its structure after framework destruction. -- Abstract: Sodalites Na{sub 8}[AlSiO{sub 4}]{sub 6}(BH{sub 4}){sub 1.8}(H{sub 3}O{sub 2}){sub 0.2} and Na{sub 8}[AlSiO{sub 4}]{sub 6}(BH{sub 4})(H{sub 3}O{sub 2}){sub 0.5}(CO{sub 3}){sub 0.25}(H{sub 2}O) were examined to characterize the influence of the mixed cage fillings and the surroundings on the thermal behaviour of enclathrated BH{sub 4}{sup -} and the stability of the alumosilicate framework. The samples were investigated in a NaCl matrix during temperature dependent IR-measurements (TIR) and by thermal analysis in inert atmosphere (helium) and in synthetic air. The thermal products were further characterized by XRD and SEM/EDS. It could be shown that the extent of the BH{sub 4}{sup -} decomposition strongly depends on the cage-fillings of the individual sodalite phase and on the environmental experimental conditions. At low to medium temperatures hydrolysis of BH{sub 4}{sup -} by water molecules from decomposition of H{sub 3}O{sub 2}{sup -} and H{sub 2}O/CO{sub 3}{sup 2-} templates leads to B(OH){sub 4}{sup -}/BH{sub 3}OH{sup -} and via subsequent dehydration to BO(OH){sub 2}{sup -} and finally BO{sub 2}{sup -}. At elevated temperatures direct oxidation of BH{sub 4}{sup -} to BO{sub 2}{sup -} occurs inside the sodalite cages. Further heating results in sodalite framework destruction and finally formation of nepheline with some boron in its structure besides some unknown polymeric borates outside the alumosilicate phase. Framework stability of the sodalites was found to decrease in the direction {yields} heating in NaCl {yields} heating in He-atmosphere {yields} heating in air.

36 MATERIALS SCIENCE↗

Influence of the process parameters on the spray pyrolysis technique, on the synthesis of gadolinium doped-ceria thin film

Graphical abstract: Gas-tight CGO made by spray pyrolysis suitable to be used as SOFC electrolyte. Display Omitted Highlights: ► Dense and crystalline CGO films deposited by spray pyrolysis on various substrates. ► Solvent did not have a strong influence on the film microstructure, defect concentration or thickness. ► The substrate did not have a strong influence on the film microstructure, defect concentration or thickness. ► Films with at least 2.5 μm of thickness presented high impermeability. ► The films obtained are suitable to use as a SOFC electrolyte. -- Abstract: This work presents the results of a process of optimization applied to gadolinia-doped ceria (Ce{sub 0.8}Gd{sub 0.2}O{sub 1.9−x}, or CGO) thin films, deposited by spray pyrolysis (SP). Spray pyrolysis is a high thermal deposition method that combines material deposition and heat treatment. This combination is advantageous since the post-deposition heat treatment step is not necessary. However, stresses are solidified in the coating during the deposition, which may lead to the initiation of a crack in the coating. The aim of this work was to achieve thin, dense, and continuous CGO coatings, which may be used as gas separation membranes and as a solid state electrochemical interfaces. Dense, flat, low-defect substrates such as silica slides, silicon mono crystal wafers, and porous substrates were used as substrates in this work. Cerium ammonium nitrate and gadolinium acetylacetonate were dissolved in ethanol and butyl carbitol to form a precursor solution that was sprayed on the heated substrates. Process parameters such as solvent composition, deposition rate and different heating regimes were analyzed. The microstructure was analyzed by secondary electron microscopy (SEM) and was found that thin, dense, and defect-free films could be produced on dense and porous substrates. The results obtained show that it is possible to obtain a CGO dense film deposited by spray pyrolysis. X-ray diffraction (XRD) analysis showed that the films were crystalline after the deposition without requiring post-deposition heat treatment. The crystallite size does not vary significantly as a function of the annealing temperature.

36 MATERIALS SCIENCE↗

Influence of temperature and precursor concentration on the synthesis of HDA-capped Ag{sub 2}Se nanoparticles

Graphical abstract: The temperature effect on the growth and size of silver selenide nanoparticles with the size distribution and XRD patterns. Highlights: ► The HDA-capped Ag{sub 2}Se nanoparticles were synthesized via the colloidal route. ► Temperature and monomer concentration of the reaction were varied. ► The concentration as a factor influenced particles with a decrease observed as the amount of Ag{sup +} ion source is increased. ► Temperature has expected influence on the growth of particles resulting in increase as the temperature is increased. ► TEM images shows spherical particles and their orthorhombic phase from structural analysis by XRD. - Abstract: The size dependent of temperature and precursor concentration on the synthesis of hexadecylamine capped Ag{sub 2}Se nanoparticles via the colloidal route were studied using the combination of optical and structural analysis. The as-prepared Ag{sub 2}Se nanoparticles showed the quantum confinement with all the obtained absorption band edges blue-shifted from the bulk and their corresponding emission maxima displaying a red-shift from band edges characterised by UV–vis absorption and photoluminescence spectroscopy. The particle sizes were obtained from transmission electron microscopy analysis. The increase in precursor concentration resulted in a decrease in nanoparticle sizes. The increase in reaction temperature showed an increase in the nanoparticle sizes, when the critical temperature at 160 °C was reached, the nanoparticle sizes decreased.

36 MATERIALS SCIENCE↗

The influence of auxiliary codopants on persistent phosphor Sr{sub 2}P{sub 2}O{sub 7}:Eu{sup 2+},R{sup 3+} (R = Y, La, Ce, Gd, Tb and Lu)

Graphical abstract: Rare earth ions which close to the line are good codopants. - Highlights: • The persistent luminescence in Sr{sub 2}P{sub 2}O{sub 7}:Eu{sup 2+},R{sup 3+} was reported. • Sr{sub 2}P{sub 2}O{sub 7}:Eu{sup 2+},Lu{sup 3+} shows the best performance. • The influence of auxiliary codopants was discussed in terms of ionic potential and ionic radius. - Abstract: We investigate the persistent luminescence in europium-doped strontium pyrophosphate upon codoping with auxiliary rare earth ions. The persistent phosphors are synthesized via solid-state reaction method under flowing N{sub 2} + H{sub 2}. Under UV irradiation, broadband emission persistent luminescence located at 420 nm is observed in all of these phosphors at room temperature. The effects of auxiliary rare earth ions on Sr{sub 2}P{sub 2}O{sub 7}:Eu{sup 2+} are discussed according to the decay curves and thermoluminescence spectra. Sr{sub 2}P{sub 2}O{sub 7}:Eu{sup 2+},Lu{sup 3+} shows the best performance, while and La{sup 3+} and Ce{sup 3+} codoped samples are the weakest. The influence of auxiliary codopants is discussed in terms of ionic potential and ionic radius. We derive an empirical formula based on the experimental results.

36 MATERIALS SCIENCE↗

Influence of preparation conditions of hollow titania–nickel composite spheres on their catalytic activity for hydrolytic dehydrogenation of ammonia borane

Highlights: • We study influence of preparation conditions on activity of hollow titania–nickel composite spheres. • The activity for hydrolytic dehydrogenation of NH{sub 3}BH{sub 3} increases with increase of Ti + Ni content. • The activity depends on the amount of PS residue in the hollow spheres. - Abstract: The present work reports influence of preparation conditions of hollow titania–nickel composite spheres on their morphology and catalytic activity for hydrolytic dehydrogenation of ammonia borane (NH{sub 3}BH{sub 3}). The as-prepared hollow titania–nickel composite spheres were characterized by transmission electron microscopy (TEM). Catalytic activities of the hollow spheres for hydrolytic dehydrogenation of aqueous NaBH{sub 4}/NH{sub 3}BH{sub 3} solution improve with the decrease of Ti + Ni content. From the results of FTIR spectra and elemental analysis, the amount of residual polystyrene (PS) templates is able to be reduced by increasing aging time for the preparation, and the catalytic activity of the hollow spheres increases when the amount of residual PS templates decreases. The carbon content in the hollow spheres prepared with aging time = 24 h is 17.3 wt.%, and the evolution of 62 mL hydrogen is finished in about 22 min in the presence of the hollow spheres from aqueous NaBH{sub 4}/NH{sub 3}BH{sub 3} solution. The molar ratio of the hydrolytically generated hydrogen to the initial NH{sub 3}BH{sub 3} in the presence of the hollow spheres is 2.7.

36 MATERIALS SCIENCE↗

Sonochemically synthesized iron-doped zinc oxide nanoparticles: Influence of precursor composition on characteristics

Highlights: • Sonochemical synthesis of iron-doped zinc oxide nanoparticles. • Green synthesis without alkali at room temperature. • Characterization by UV–vis spectroscopy, FESEM, XRD and EDX. • Influence of precursor composition on characteristics. • Composition and characteristics are correlated. - Abstract: Iron-doped zinc oxide nanoparticles have been synthesized sonochemically from aqueous acetyl acetonate precursors of different proportions. Synthesized nanoparticles were characterized with UV–vis spectroscopy, X-ray diffraction and microscopy. Influences of precursor mixture on the characteristics have been examined and modeled. Linear correlations have been proposed between dopant dosing, extent of doping and band gap energy. Experimental data corroborated with the proposed models.

36 MATERIALS SCIENCE↗

Dosimetric influences of rotational setup errors on head and neck carcinoma intensity-modulated radiation therapy treatments

The purpose of this work is to investigate the dosimetric influence of the residual rotational setup errors on head and neck carcinoma (HNC) intensity-modulated radiation therapy (IMRT) with routine 3 translational setup corrections and the adequacy of this routine correction. A total of 66 kV cone beam computed tomography (CBCT) image sets were acquired on the first day of treatment and weekly thereafter for 10 patients with HNC and were registered with the corresponding planning CT images, using 2 3-dimensional (3D) rigid registration methods. Method 1 determines the translational setup errors only, and method 2 determines 6-degree (6D) setup errors, i.e., both rotational and translational setup errors. The 6D setup errors determined by method 2 were simulated in the treatment planning system and were then corrected using the corresponding translational data determined by method 1. For each patient, dose distributions for 6 to 7 fractions with various setup uncertainties were generated, and a plan sum was created to determine the total dose distribution through an entire course and was compared with the original treatment plan. The average rotational setup errors were 0.7°± 1.0°, 0.1°±1.9°, and 0.3°±0.7° around left-right (LR), anterior-posterior (AP), and superior-inferior (SI) axes, respectively. With translational corrections determined by method 1 alone, the dose deviation could be large from fraction to fraction. For a certain fraction, the decrease in prescription dose coverage (V{sub p}) and the dose that covers 95% of target volume (D{sub 95}) could be up to 15.8% and 13.2% for planning target volume (PTV), and the decrease in V{sub p} and the dose that covers 98% of target volume (D{sub 98}) could be up to 9.8% and 5.5% for the clinical target volume (CTV). However, for the entire treatment course, for PTV, the plan sum showed that the average V{sub p} was decreased by 4.2% and D{sub 95} was decreased by 1.2 Gy for the first phase of IMRT with a prescription dose of 50 Gy. For CTV, the plan sum showed that the average V{sub p} was decreased by 0.8% and D{sub 98}, relative to prescription dose, was not decreased. Among these 10 patients, the plan sum showed that the dose to 1-cm{sup 3} spinal cord (D{sub 1cm{sup 3}}) increased no more than 1 Gy for 7 patients and more than 2 Gy for 2 patients. The average increase in D{sub 1cm{sup 3}} was 1.2 Gy. The study shows that, with translational setup error correction, the overall CTV V{sub p} has a minor decrease with a 5-mm margin from CTV to PTV. For the spinal cord, a noticeable dose increase was observed for some patients. So to decide whether the routine clinical translational setup error correction is adequate for this HNC IMRT technique, the dosimetric influence of rotational setup errors should be evaluated carefully from case to case when organs at risk are in close proximity to the target.

61 RADIATION PROTECTION AND DOSIMETRY↗

Influence of computed tomography contrast agent on radiotherapy dose calculation for pancreatic carcinoma: A dosimetric study based on tomotherapy and volumetric-modulated arc therapy techniques

The main purpose of our investigation was to quantify the dosimetric influence of intravenous contrast agent for pancreatic cancer radiotherapy treatment. This study focused on complex modulated irradiation techniques of tomotherapy (TOMO) and volumetric-modulated arc therapy (VMAT) to investigate if novel conformal treatment methods could reduce the influence of contrast agent. In our study, patients with pancreatic cancer were enrolled to have 2 computed tomography (CT) scans in the same position without and with intravenous contrast agent for treatment planning. Then tumors and organ at risks were countered on contrast-enhanced CT (CECT) images. Each patient's CECT was assigned a TOMO plan and a VMAT plan. Then these plans were copied onto the non-CECT image and dose distribution was calculated with the same algorithm and structure sets. Finally, the dose distribution and the dose difference were analyzed for the target volume and organs at risk between the 2 sets of images. The statistic dosimetric result showed that for both TOMO and VMAT, no significant dose difference between CECT and non-CECT-based plan was observed. Dose difference was clinically negligible because the average relative percentage dose difference was 1% ± 1% for target volume, except a blurring effect at the higher dose region of the target volume. It implied that intravenous contrast agent will not affect dose calculation for pancreatic cancer radiotherapy significantly. Also the dose deviation based on TOMO showed no statistical difference compared with that on VMAT. For both superposition/conversation algorithm used by TOMO and Monte Carlo algorithm used by VMAT, the dosimetric difference was nonsignificant. A full analysis demonstrated a negligible dose difference of less than 1% between CECT-based plan and non-CECT-based plan. Therefore, contrast-enhanced CT image can be used directly for dose calculation of TOMO and VMAT plans for pancreatic cancer. It is unnecessary to scan twice then make a fusion of CECT and non-CECT, which would result to additional unnecessary radiation dose to patient and decrease work efficiency.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Influence of non-solvent chemistry on polybenzimidazole hollow fiber membrane preparation

Polybenzimidazole membrane materials have attractive H 2 /CO 2 separation characteristics and high thermo-chemical stability for elevated temperature synthesis (syn) gas separations. The development of PBI membranes with a thin defect-free selective layer and porous support morphology is vital to achieving industrially attractive separation performance. This work is focused on developing a fundamental understanding of the liquid-liquid demixing-based phase inversion process for asymmetric PBI hollow fiber membrane (HFM) formation. The development of industrially attractive HFMs is a challenging process due to the complex interplay between phase equilibria, phase inversion kinetics, and interfacial mass transfer that exist during the liquid-liquid demixing process. Numerous parameters including the dope, bore, and outer coagulant chemistries and compositions significantly influence the HFM morphologies produced. Here, a systematic study is conducted to investigate the phase inversion process parameters including the roles of the non-solvent solubility and diffusivity parameters with respect to the solvent and PBI on the phase inversion process. Furthermore, the influence of dope, bore and coagulant chemistries and compositions on PBI HFM morphology are investigated. As a result, the fabricated PBI HFMs are evaluated for their ideal H 2 and CO 2 permeance and H 2 /CO 2 selectivity at 250 °C to benchmark their separation performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Interfacial interactions between polymers and selective adsorbents influence ion transport properties of boron scavenging ion-exchange membranes

The recent emergence of adsorptive ion-exchange membranes (IEMs), designed by the synergistic integration of highly selective porous aromatic frameworks (PAFs) with ion-exchange polymers, has enabled simultaneous desalination and targeted removal of specific solutes (e.g., mercury, iron, boron, etc.). While the addition of highly selective PAFs to IEMs yields membranes with entirely new functions, PAF-polymer interactions, and the effects of such interactions on ion transport properties of the membranes, are not well understood. In this study, we developed cross-linked adsorptive cation- and anion-exchange membranes (CEMs and AEMs) for simultaneous desalination and boron removal via in-situ formation of the cross-linked polymer network around the boron selective PAF particles. Here we systematically investigated the influence of PAF loading level on PAF-polymer interactions as well as the equilibrium and transport properties of the adsorptive IEMs. The interactions between the PAF and the ion-exchange polymer matrix differed for the CEMs and AEMs due to differences in the fixed charge group chemistry. Notably, the sulfonate groups of the CEMs can form hydrogen bonds with the hydroxyl groups of the PAF, while the quaternary ammonium groups in the AEMs cannot. These differences in interfacial interactions did not significantly impact counter-ion transport across the adsorptive IEMs but had a significant influence on co-ion transport, which affected the counter-ion/co-ion selectivity of the membranes. The selectivity of the adsorptive CEMs decreased while that of the adsorptive AEMs increased with PAF loading level. The results of this study underscore the importance of controlling interfacial interactions when designing adsorptive IEMs for simultaneous water desalination and solute capture and recovery.

36 MATERIALS SCIENCE↗

Influence of Sn on Martensitic Beta Ti Alloys

The influence of Sn composition in Ti-17 at.% Nb alloys is studied by cyclic tension and in-situ synchrotron X-ray diffraction. It is essentially found that Sn stabilizes β-phase and effectively suppresses the formation of ω-phase. Along with β-phase stability, we detect lowering of the austenite and martensite transformation temperature by ~ 100 K/at.% and 88 K/at.%, respectively. Increasing Sn decreases the martensitic transformation strain in Ti-Nb alloys by ~ 1.4%/at.%, larger than that in Ti-Zr-Nb-Sn systems. The influence of Sn in martensitic Ti is anisotropic: causing larger reduction in lattice parameter b and higher decreases in elastic moduli of grain families that are aligned close to the b -axis. Lastly, a {013} α'' , {031} α'' ,{122} α'' and {211} α'' quadruple texture was observed in martensitic Ti wire. At the early stage of deformation, detwinning quickly rotated {013} α'' and (211} α'' , towards {031} α'' and {122} α'' components. After that, the strength of {031} α'' continued to increase, while the strength of {122} α'' texture was gradually decreased by dislocation slip as deformation continued.

36 MATERIALS SCIENCE↗