Search NASA⌕ Search

SEARCH · Search NASA

Results for “numerical simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Brush seal numerical simulation: Concepts and advances

The development of the brush seal is considered to be most promising among the advanced type seals that are presently in use in the high speed turbomachinery. The brush is usually mounted on the stationary portions of the engine and has direct contact with the rotating element, in the process of limiting the 'unwanted' leakage flows between stages, or various engine cavities. This type of sealing technology is providing high (in comparison with conventional seals) pressure drops due mainly to the high packing density (around 100 bristles/sq mm), and brush compliance with the rotor motions. In the design of modern aerospace turbomachinery leakage flows between the stages must be minimal, thus contributing to the higher efficiency of the engine. Use of the brush seal instead of the labyrinth seal reduces the leakage flow by one order of magnitude. Brush seals also have been found to enhance dynamic performance, cost less, and are lighter than labyrinth seals. Even though industrial brush seals have been successfully developed through extensive experimentation, there is no comprehensive numerical methodology for the design or prediction of their performance. The existing analytical/numerical approaches are based on bulk flow models and do not allow the investigation of the effects of brush morphology (bristle arrangement), or brushes arrangement (number of brushes, spacing between them), on the pressure drops and flow leakage. An increase in the brush seal efficiency is clearly a complex problem that is closely related to the brush geometry and arrangement, and can be solved most likely only by means of a numerically distributed model.

Braun, M. J.↗
NASA NTRS1987

Numerical simulation by TVD schemes of complex shock reflections from airfoils at high angle of attack

The shock-capturing capability of total variation diminishing (TVD) schemes is demonstrated for a more realistic complex shock-diffraction problem for which the experimental data are available. Second-order explicit upwind and symmetric TVD schemes are used to solve the time-dependent Euler equations of gas dynamics for the interaction of a blast wave with an airfoil at high angle-of-attack. The test cases considered are a time-dependent moving curved-shock wave and a contant moving planar-shock wave impinging at an angle-of-attack 30 deg on a NACA 0018 airfoil. Good agreement is obtained between isopycnic contours computed by the TVD schemes and those from experimental interferograms. No drastic difference in flow-field structure is found between the curved- and planar-shock wave cases, except for a difference in density level near the lower surface of the airfoil. Computation for cases with higher shock Mach numbers is also possible. Numerical experiments show that the symmetric TVD scheme is less sensitive to the boundary conditions treatment than the upwind scheme.

Moon, Young J.↗
NASA NTRS1992

Numerical simulation of aerothermal loads in hypersonic engine inlets due to shock impingement

The effect of shock impingement on an axial corner simulating the inlet of a hypersonic vehicle engine is modeled using a finite-difference procedure. A three-dimensional dynamic grid adaptation procedure is utilized to move the grids to regions with strong flow gradients. The adaptation procedure uses a grid relocation stencil that is valid at both the interior and boundary points of the finite-difference grid. A linear combination of spatial derivatives of specific flow variables, calculated with finite-element interpolation functions, are used as adaptation measures. This computational procedure is used to study laminar and turbulent Mach 6 flows in the axial corner. The description of flow physics and qualitative measures of heat transfer distributions on cowl and strut surfaces obtained from the analysis are compared with experimental observations. Conclusions are drawn regarding the capability of the numerical scheme for enhanced modeling of high-speed compressible flows.

Ramakrishnan, R.↗
NASA NTRS1993

Three-dimensional numerical simulation of thermal tides in the Martian atmosphere

Analysis of the Mariner 9 IRIS and Viking Orbiter IRTM temperature data and of the time series of surface pressure from the Viking landers has indicated that atmospheric thermal tides are a significant component of the martian general circulation. Classical tidal theory, considering only the Sun synchronous components, has been shown to at least roughly account for the amplitudes of the observed diurnal and semidirunal surface pressure oscillations. In particular, Zurek and Leovy have demonstrated that classical tidal theory can reproduce the observed dependence of the strength of the semidiurnal tide on aerosol optical depth. The high-amplitude topograph of Mars, however, can cause longitudinal distortions in the thermotidal forcing, leading to additional tidal modes that are not Sun synchronous. In particular, observation and theory have suggested the likely presence of a diurnal, zonal wavenumber-1 K wave. Hamilton and Garcia noted that the wavenumber-1 K normal mode has a period of close to 24 hr and may be detectable in surface pressure observations. Zurek has discussed the possibility of this mode being resonantly excited for various atmospheric temperature studies. The semidiurnal wavenumber-2 K mode, with roughly a 12-hr period, could also be resonantly excited. A numerical model with finite amplitude topography and a self-consistent thermotidal forcing resulting from the daily heat flux at the surface and atmospheric absorption of solar radiation by aerosols is used here to explore the influence of topography on martian thermal tides and to examine the possibility of Kelvin wave resonance.

Wilson, R. John↗
NASA NTRS1982

Numerical simulation of the flow and fuel-air mixing in an axisymmetric piston-cylinder arrangement

The implicit factored method of Beam and Warming was employed to describe the flow and the fuel-air mixing in an axisymmetric piston-cylinder configuration during the intake and compression strokes. The governing equations were established on the basis of laminar flow. The increased mixing due to turbulence was simulated by appropriately chosen effective transport properties. Calculations were performed for single-component gases and for two-component gases and for two-component gas mixtures. The flow field was calculated as functions of time and position for different geometries, piston speeds, intake-charge-to-residual-gas-pressure ratios, and species mass fractions of the intake charge. Results are presented in graphical form which show the formation, growth, and break-up of those vortices which form during the intake stroke and the mixing of fuel and air throughout the intake and compression strokes. It is shown that at bore-to-stroke ratio of less than unity, the vortices may break-up during the intake stroke. It is also shown that vortices which do not break-up during the intake stroke coalesce during the compression stroke. The results generated were compared to existing numerical solutions and to available experimental data.

Shih, T. I. P.↗
NASA NTRS1999

Multistage Turbomachinery Flows Simulated Numerically

At the NASA Lewis Research Center, a comprehensive assessment was made of the predictive capability of the average passage flow model as applied to multistage axial-flow compressors. This model, which describes the time-averaged flow field within a typical passage of a blade row embedded in a multistage configuration, is being widely used throughout U.S. aircraft industry as an integral part of their design systems. Rotor flow-angle deviation. In this work, detailed data taken within a four and one-half stage large low-speed compressor were used to assess the weaknesses and strengths of the predictive capabilities of the average passage flow model. The low-speed compressor blading is of modern design and employs stator end-bends. Measurements were made with slow- and high response instrumentation. The high-response measurements revealed the velocity components of both the rotor and stator wakes. From the measured wake profiles, we found that the flow exiting the rotors deviated from the rotor exit metal angle to a lesser degree than was predicted by the average passage flow model. This was found to be due to blade boundary layer transition, which recently has been shown to exist on multistage axial compressor rotor and stator blades, but was not accounted for in the average passage model. Consequently, a model that mimics the effects of blade boundary layer transition, Shih k-epsilon model, was incorporated into the average passage model. Simulations that incorporated this transition model showed a dramatic improvement in agreement with data. The altered model thus improved predictive capability for multistage axial-flow compressors, and this was verified by detailed experimental measurement.

Hathaway, Michael D.↗
NASA NTRS2001

Numerical Simulation of an Enclosed Laminar Jet Diffusion Flame in Microgravity Environment: Comparison with ELF Data

Enclosed diffusion flames are commonly found in practical combustion systems, such as the power-plant combustor, gas turbine combustor, and jet engine after-burner. In these systems, fuel is injected into a duct with a co-flowing or cross-flowing air stream. The diffusion flame is found at the surface where the fuel jet and oxygen meet, react, and consume each other. In combustors, this flame is anchored at the burner (i.e., fuel jet inlet) unless adverse conditions cause the flame to lift off or blow out. Investigations of burner stability study the lift off, reattachment, and blow out of the flame. Flame stability is strongly dependent on the fuel jet velocity. When the fuel jet velocity is sufficiently low, the diffusion flame anchors at the burner rim. When the fuel jet velocity is increased, the flame base gradually moves downstream. However, when the fuel jet velocity increases beyond a critical value, the flame base abruptly jumps downstream. When this "jump" occurs, the flame is said to have reached its lift-off condition and the critical fuel jet velocity is called the lift-off velocity. While lifted, the flame is not attached to the burner and it appears to float in mid-air. Flow conditions are such that the flame cannot be maintained at the burner rim despite the presence of both fuel and oxygen. When the fuel jet velocity is further increased, the flame will eventually extinguish at its blowout condition. In contrast, if the fuel jet velocity of a lifted flame is reduced, the flame base moves upstream and abruptly returns to anchor at the burner rim. The fuel jet velocity at reattachment can be much lower than that at lift off, illustrating the hysteresis effect present in flame stability. Although there have been numerous studies of flame stability, the controlling mechanisms are not well understood. This uncertainty is described by Pitts in his review of various competing theories of lift off and blow out in turbulent jet diffusion flames. There has been some research on the stability of laminar flames, but most studies have focused on turbulent flames. It is also well known that the airflow around the fuel jet can significantly alter the lift off, reattachment and blow out of the jet diffusion flame. Buoyant convection is sufficiently strong in 1-g flames that it can dominate the flow-field, even at the burner rim. In normal-gravity testing, it is very difficult to delineate the effects of the forced airflow from those of the buoyancy-induced flow. Comparison of normal-gravity and microgravity flames provides clear indication of the influence of forced and buoyant flows on the flame stability. The overall goal of the Enclosed Laminar Flames (ELF) investigation (STS-87/USMP-4 Space Shuttle mission, November to December 1997) is to improve our understanding of the effects of buoyant convection on the structure and stability of co-flow diffusion flame, e.g., see http://zeta.lerc.nasa.gov/expr/elf.htm. The ELF hardware meets the experiment hardware limit of the 35-liter interior volume of the glovebox working area, and the 180x220-mm dimensions of the main door. The ELF experiment module is a miniature, fan-driven wind tunnel, equipped with a gas supply system. A 1.5-mm diameter nozzle is located on the duct's flow axis. The cross section of the duct is nominally a 76-mm square with rounded corners. The forced air velocity can be varied from about 0.2 to 0.9 m/s. The fuel flow can be set as high as 3 std. cubic centimeter (cc) per second, which corresponds to a nozzle exit velocity of up to 1.70 m/s. The ELF hardware and experimental procedure are discussed in detail in Brooker et al. The 1-g test results are repeated in several experiments following the STS-87 Mission. The ELF study is also relevant to practical systems because the momentum-dominated behavior of turbulent flames can be achieved in laminar flames in microgravity. The specific objectives of this paper are to evaluate the use reduced model for simulation of flame lift-off and blowout.

Jia, Kezhong↗
NASA NTRS1994

Hot gas in the cold dark matter scenario: X-ray clusters from a high-resolution numerical simulation

A new, three-dimensional, shock-capturing hydrodynamic code is utilized to determine the distribution of hot gas in a standard cold dark matter (CDM) model of the universe. Periodic boundary conditions are assumed: a box with size 85 h(exp -1) Mpc having cell size 0.31 h(exp -1) Mpc is followed in a simulation with 270(exp 3) = 10(exp 7.3) cells. Adopting standard parameters determined from COBE and light-element nucleosynthesis, sigma(sub 8) = 1.05, omega(sub b) = 0.06, and assuming h = 0.5, we find the X-ray-emitting clusters and compute the luminosity function at several wavelengths, the temperature distribution, and estimated sizes, as well as the evolution of these quantities with redshift. We find that most of the total X-ray emissivity in our box originates in a relatively small number of identifiable clusters which occupy approximately 10(exp -3) of the box volume. This standard CDM model, normalized to COBE, produces approximately 5 times too much emission from clusters having L(sub x) is greater than 10(exp 43) ergs/s, a not-unexpected result. If all other parameters were unchanged, we would expect adequate agreement for sigma(sub 8) = 0.6. This provides a new and independent argument for lower small-scale power than standard CDM at the 8 h(exp -1) Mpc scale. The background radiation field at 1 keV due to clusters in this model is approximately one-third of the observed background, which, after correction for numerical effects, again indicates approximately 5 times too much emission and the appropriateness of sigma(sub 8) = 0.6. If we have used the observed ratio of gas to total mass in clusters, rather than basing the mean density on light-element nucleosynthesis, then the computed luminosity of each cluster would have increased still further, by a factor of approximately 10. The number density of clusters increases to z approximately 1, but the luminosity per typical cluster decreases, with the result that evolution in the number density of bright clusters is moderate in this redshift range, showing a broad peak near z = 0.7, and then a rapid decline above redshift z = 3. Detailed computations of the luminosity functions in the range L(sub x) = 10(exp 40) - 10(exp 44) ergs/s in various energy bands are presented for both cluster central regions and total luminosities to be used in comparison with ROSAT and other observational data sets. The quantitative results found disagree significantly with those found by other investigators using semianalytic techniques. We find little dependence of core radius on cluster luminosity and a dependence of temperature on luminosity given by log kT(sub x) = A + B log L(sub x), which is slightly steeper (B = 0.38) than is indicated by observations. Computed temperatures are somewhat higher than observed, as expected, in that COBE-normalized CDM has too much power on the relevant scales. A modest average temperature gradient is found, with temperatures dropping to 90% of central values at 0.4 h(exp -1) Mpc and 70% of central values at 0.9 h(exp -1) Mpc. Examining the ratio of gas to total mass in the clusters normalized to Omega(sub B) h(exp 2) = 0.015, and comparing with observations, we conclude, in agreement with White (1991), that the cluster observations argue for an open universe.

Kang, Hyesung↗
NASA NTRS1995

Application of high-performance computing to numerical simulation of human movement

We have examined the feasibility of using massively-parallel and vector-processing supercomputers to solve large-scale optimization problems for human movement. Specifically, we compared the computational expense of determining the optimal controls for the single support phase of gait using a conventional serial machine (SGI Iris 4D25), a MIMD parallel machine (Intel iPSC/860), and a parallel-vector-processing machine (Cray Y-MP 8/864). With the human body modeled as a 14 degree-of-freedom linkage actuated by 46 musculotendinous units, computation of the optimal controls for gait could take up to 3 months of CPU time on the Iris. Both the Cray and the Intel are able to reduce this time to practical levels. The optimal solution for gait can be found with about 77 hours of CPU on the Cray and with about 88 hours of CPU on the Intel. Although the overall speeds of the Cray and the Intel were found to be similar, the unique capabilities of each machine are better suited to different portions of the computational algorithm used. The Intel was best suited to computing the derivatives of the performance criterion and the constraints whereas the Cray was best suited to parameter optimization of the controls. These results suggest that the ideal computer architecture for solving very large-scale optimal control problems is a hybrid system in which a vector-processing machine is integrated into the communication network of a MIMD parallel machine.

NASA Discipline Musculoskeletal↗
DOE OSTI2025

Numerical simulation for the design of induction heating based radio frequency reactor for ethylene production

Ethylene is a vital petrochemical compound produced in vast amounts yearly by manufacturers that have enough scale to overcome the inherent thermodynamic inefficiencies of the process. In order to address the inefficiencies that prevent smaller scale or intermittent production ethylene, investigation of new production methods are required. In this work, we investigate the use of a radio frequency (RF) based reactor system that generates heat internally as opposed to applying heat externally via steam or direct combustion of fossil fuels. In order to guide the design of an electromagnetic based reactor system, we have created a macroscale model capable of capturing heat generation at the susceptors from a produced electromagnetic field and subsequent chemical reactions. Several susceptor and induction coil designs were investigated to better understand the performance of the system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Numerical simulation of asteroid geometry variance on airburst threat

For an atmospheric airburst the primary source of concern when assessing uncertainty is the size and velocity. Determining these properties provides the basis for threat assessment, as the total energy of the asteroid may then be estimated, and the threat investigated thoroughly. Even with clarity as to how much energy an asteroid may deposit, a great deal of uncertainty still exists for the actual energy deposition process. One such source of uncertainty is the geometry of the incoming asteroid. The geometry of an asteroid will alter the stress distribution during entry, which adds uncertainty to when fracture will occur. Here, in this study, we use Smoothed Particle Hydrodynamics to model the atmospheric airburst of Tunguska-scale asteroids with varying geometric profiles, including a sphere, ellipsoid, binary and superellipsoid. Each asteroid is modeled as a homogenous structure with strength. We assess uncertainty through a series of planar 2D simulation cases for each geometry, comparing the source of stochasticity across geometries. A single 3D airburst simulation for each geometry is also analyzed. Additionally, the 3D cases are compared to the highly uncertain Tunguska event, predicting variance in burst height across geometries, but all bounded by theoretical burst heights proposed for Tunguska.

Airburst↗
DOE OSTI2026

Numerical simulation of vortex-induced vibration response of a single IEA 10-MW wind turbine blade

Three-dimensional simulation of vortex-induced vibration (VIV) of a single International Energy Agency (IEA) 10-MW reference wind turbine blade with a length of 97.325 m is performed using the ExaWind stack, an open-source suite of codes. This study aims to illustrate the spanwise VIV response characteristics and cross-validate the results with an existing commercial framework. Five near-body meshes and three time steps are selected for the convergence study. To improve computational efficiency, several VIV triggering methods are also compared to shorten the VIV development period. The ExaWind-based VIV simulation strategy for a single IEA 10-MW blade is determined. First, the modal shape is validated against published results. Then, spanwise VIV responses of four blade configurations under a fixed and varied incoming flow velocity are analyzed. Results show that the VIV response is dominated by the first edgewise (second overall) mode. Little first-mode contributions appear near the second-mode node, producing a pi phase jump, and a higher harmonics response occurs near the blade root. Rotational degrees of freedom are minor compared with translational motion. The response versus reduced velocity is analyzed, showing a two-branch behavior similar to that of VIV for a bluff cylinder. Across all tested cases, the dominant frequency remains locked to the natural frequency of the second mode with no observed desynchronization. A mild deviation is observed for the case of 90-degree pitch and 310-degree azimuth rotation near a reduced velocity of 6, which will be examined with additional cases in future work. These findings indicate that severe VIV responses can arise under specific configurations and flow conditions, thereby increasing the potential for VIV fatigue damage and requiring greater attention during operation.

17 WIND ENERGY↗
DOE OSTI2024

High resolution numerical simulations of methane pool fires using adaptive mesh refinement

The ability to accurately predict the structure and dynamics of pool fires using computational simulations is of great interest in a wide variety of applications, including accidental and wildland fires. However, the presence of physical processes spanning a broad range of spatial and temporal scales poses a significant challenge for simulations of such fires, particularly at conditions near the transition between laminar and turbulent flow. Here, in this study, we examine the transition to turbulence in methane pool fires using high-resolution simulations with multi-step finite rate chemistry, where adaptive mesh refinement (AMR) is used to directly resolve small-scale flow phenomena. We perform three simulations of methane pool fires, each with increasing diameter, corresponding to increasing inlet Reynolds and Richardson numbers. As the diameter increases, the flow transitions from organized vortex roll-up via the puffing instability to much more chaotic mixing associated with finger formation along the shear layer and core collapse near the inlet. These effects combine to create additional mixing close to the inlet, thereby enhancing fuel consumption and causing more rapid acceleration of the fluid above the pool. We also make comparisons between the transition to turbulence and core collapse in the present pool fires and in inert helium plumes, which are often used as surrogates for the study of buoyant reacting flows.

42 ENGINEERING↗
DOE OSTI2024

Numerical Simulation and Experimental Comparison of System Analysis Module 1D Mixing Model for Cold Shock Transients in the Gallium Thermal-Hydraulic Mixing Facility

Abstract Liquid metals are being investigated as coolants in many advanced reactor designs because of their high thermal conductivity and effectiveness at high temperatures. However, they often pose challenges to reactor operation and safety because of the complex thermal mixing and stratification in the plenum of pool-type reactor designs. The advanced system analysis code System Analysis Module (SAM) currently under development at Argonne National Laboratory aims to develop and implement thermal mixing models to accurately capture these complex thermal fluid behaviors. In this study, the SAM thermal mixing model was compared against experimental data from the Gallium Thermal-Hydraulic Experiment facility, a scaled liquid metal test facility that uses gallium as a surrogate fluid to investigate the stratification and thermal mixing of low-Prandtl-number fluids in the upper plenum of a liquid metal-cooled reactor. Two cold shock transient cases were used: one with stable stratified flow (Ri = 32) and one with stronger thermal mixing (Ri = 0.5). The resultant temperatures were then compared with the experimental temperatures over the entire plenum to assess the ability of the mixing models to capture the thermal behavior and to better correspond mixing parameters to various flow scenarios. Generally, the zero-dimensional mixing model was more capable of capturing the bulk temperature of the component modeled assuming that an accurate mass flow rate was provided, but it was inherently unable to capture thermal gradients in space. The one-dimensional mixing model was capable of capturing that the thermal gradients provided accurate selection of the mixing coefficients. Further, the temperature at the outlet junction was compared over time for each of the mixing models with the recorded experimental temperature. The implemented mixing models demonstrated the ability to effectively capture the overall thermal behavior for stronger mixing scenarios but struggled with more stably stratified flows. It was found that a system analysis code's covering of the entire range of different operating conditions still remains a challenging task, and it is suggested that further model and closure improvements are necessary to accurately capture complex thermal mixing and stratification phenomena.

stratification↗
DOE OSTI2026

Numerical Simulation of a Natural Convection–Driven Air-Cooled Reactor Cavity Cooling System Experiment

Ensuring the efficient removal of decay heat from the reactor vessel is essential for the safety of advanced reactor technologies. Several Generation-IV concepts incorporate variations in the reactor vessel cooling systems to achieve this objective. High-temperature gas-cooled reactors utilize a reactor cavity cooling system (RCCS), a passive ex-vessel system designed to operate without active components or external power during accident conditions. The RCCS removes decay heat primarily through radiative and convective heat transfer mechanisms. Here, this study presents a comprehensive validation of a computational fluid dynamics Reynolds-averaged Navier-Stokes model for the University of Wisconsin-Madison air-cooled RCCS facility. Validation was conducted for both high- and low-power natural convection cases under a uniform heating profile. Near-wall resolution was found to be critical for accurately modeling natural convection in the RCCS; employing an all-𝑦 + wall treatment resulted in wall temperature discrepancies exceeding 50 °⁢𝐶 compared to a wall-resolved mesh. Thermal-hydraulic behaviors under natural and forced convection conditions were compared within the heated cavity and RCCS. A turbulence model sensitivity analysis indicated that low-Reynolds number k-ɛ, k-ω shear stress transport (SST), and Reynolds stress transport models produce similar wall temperature predictions. A buoyancy modeling sensitivity study revealed that the Boussinesq approximation significantly underpredicted thermal-hydraulic behavior in the RCCS. Based on these findings, modeling recommendations are provided. The validated data set along with identified sensitivities refine the modeling of natural convection in the RCCS. The information produced by this study supports RCCS design, optimization, and safety evaluations, enabling the calibration and verification of reduced-order thermal-hydraulic models.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗