Search NASA⌕ Search

SEARCH · Search NASA

Results for “positional dependence”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Identification of nonlinear system parameters in joints using the force-state mapping technique

A procedure is presented for identifying the potentially strong nonlinear properties of structural members, such as joints, by expressing the force transmitted by the member as a function of its mechanical state. By explicitly including position and rate dependent effects, the surface of transmitted force versus state, the force-state map, has distinct, unique, superposable features for common structural nonlinearities, even those which appear to indicate hysteresis on a force-stroke presentation. An analysis is performed on the influence of true memory effects, transient response, and uncertainty in the measurements and system mass on the precision of the procedure. The successful identification of simulated data verifies the accuracy of the identification algorithm. Tests are then conducted on three actual joint models, with incomplete state measurements typical of an actual testing environment. The ability of the procedure to estimate the complete state vector and to analyze and reconstruct the measured nonlinear characteristics is demonstrated.

Crawley, E. F.↗

Straight cylindrical seal for high-performance turbomachines

A straight cylindrical seal configuration representing the seal for a high-performance turbopump (e.g., the space shuttle main engine fuel pump) was tested under static (nonrotating) conditions. The test data included critical mass flux and pressure profiles over a wide range of inlet temperatures and pressures for fluid nitrogen and fluid hydrogen with the seal in concentric and fully eccentric positions. The critical mass fluxes (or leakage rates) for the concentric and fully eccentric configurations were nearly the same when based on stagnation conditions upstream of the seal. The fully eccentric configuration pressure profiles of the gas and liquid were different. Further, the pressure differences between the maximum and the minimum clearance positions were highly dependent on the geometric conditions, the temperature, and the absolute pressure at both the inlet and the exit. The pressure differences were greatest in the inlet region. The results, although complex, tend to follow the corresponding-states principles for critical flows. Gaseous injection near the seal exit plane significantly altered the pressure profiles and could be used to control turbomachine instabilities.

Hendricks, Robert C.↗

Logistics and operations integration requirements to support Space Station servicing of free flying spacecraft - OMV flight operation

The logistics of OMV free-flyer servicing are examined, with emphasis on integrating the OMV operations into the overall STS-Space Station system. The depletion rate of consumables and lifetimes of free-flyer components are known quantities, which permits definition of a predictable maintenance schedule. Servicing with an OMV will depend on the position and capabilities of the OMV, Shuttle and Station when free-flyer maintenance is needed. Optimized orbital servicing of free-flyers will involve coordination of and resolution of schedule conflicts among STS, the OMV and the Station. The scheduled availability of any of the three components will be predicted in terms of probabilities that any one of the components will not be needed for another mission while performing the mission they are on.

Bell, Jerome A.↗

On helicopter rotor low frequency broadband noise

The effect of shear-layer-type inflow turbulence on the low-frequency broadband noise of a model helicopter rotor is experimentally studied. The measurements and the one-dimensional energy spectral density indicate that the upstream airfoil wake turbulence is nonisotropic, but approaches isotropy at high wavenumbers. Turbulence measurements also indicate that the wake turbulence is weak. The effect of the inflow turbulence intensity on the peak sound pressure level follows an intensity-velocity squared scaling law. A number of length scales and turbulence intensities exist which can be measured in the airfoil wake depending on the position at which the measurements are taken. Comparison of experimental and theoretical sound pressure power spectral densities indicates that the initial anisotropy of the inflow turbulence does not invalidate the isotropic turbulence assumption made in noise prediction models as long as measured turbulence intensities and length scales are used.

Williams, Morgan↗

Active control of sound fields in elastic cylinders by multi-control forces

An unstiffened cylindrical model was used to study the control of sound transmission into aircraft cabins by the use of multi-control forces applied directly to the cylinder wall. External acoustic monopoles were located on each side of the cylinder to approximate the propeller noise source. This allowed the study of a dual control system utilizing multi-control forces in conjunction with synchrophasing of the twin acoustic monopole sources. For acoustic resonant conditions within the cavity, a spatially averaged noise reduction of approximately 30 dB was achieved using the active control system for both in-phase and out-of-phase monopoles; however, effective reduction of the sound field was dependent upon judiciously positioning the control forces for optimal control of the sound field.

Jones, J. D.↗

Unsteady pressure measurements on a supercritical airfoil at high Reynolds numbers

Steady and unsteady pressures were measured on a 14 percent supercritical airfoil at transonic Mach numbers at Reynolds numbers from 6,000,000 to 35,000,000. Instrumentation techniques were developed to measure unsteady pressures in a cryogenic tunnel at flight Reynolds numbers. Experimental steady data, corrected for wall effects show very good agreement with calculations from a full potential code with an interacted boundary layer. The steady and unsteady pressures both show a shock position that is dependent on Reynolds number. For a supercritical pressure distribution at a chord Reynolds number of 35,000,000 laminar flow was observed between the leading edge and the shock wave at 45 percent chord.

Hess, R. W.↗

Analytic theory for the selection of Saffman-Taylor fingers in the presence of thin film effects

An analytic theory is presented for the width selection of Saffman-Taylor fingers in the presence of thin film effect. In the limit of small capillary number Ca and small gap to width ratio epsilon, such that epsilon much less than Ca much less than 1, it is found that fingers with relative width lambda less than 1/2 are possible such that lambda squared (1-lambda)/(1-2 lambda) = k epsilon/Ca(sup 3/2), where the positive constant k depends on the branch of solution and equals 2.776 for the first branch. A fully nonlinear analysis is necessary in this problem even to obtain the correct scaling law. It is also shown how in principle, the selection rule for arbitrary Ca can be obtained.

Tanveer, S.↗

Cirrus radiative characteristics and the radiative impact of small particles

An understanding of the way radiation interacts with clouds is vital for understanding the sensitivity of the earth's climate to both natural and anthropogenic changes in the atmosphere. Cirrus clouds are thought to be an important modulator of climate sensitivity. The feedback effect of cirrus on climate can be positive or negative depending upon the microphysics and scattering properties of the cloud. These properties of cirrus clouds are not well understood partly because of their thin tenuous nature and partly because of their microphysical properties. The high altitude and cold temperatures within these clouds along with their transparency greatly increase the difficulty in which accurate measurements can be obtained and interpreted both by aircraft and remote sensing. Therefore, the understanding of the interaction of radiation in cirrus clouds is crucial to determining the ways in which these clouds interact with climate forcings. The sensitivity of the radiative budgets of cirrus cloudiness to their microphysical composition and the environments in which they occur is examined. Especially important is the impact of small particles on the radiative properties of cirrus. Remote sensing estimates of the effective crystal size of cirrus and in situ measurements show large differences up to 100 microns. Thus it becomes important to identify the sources of these differences. For this reason, simulations of actual FIRE cases are compared with the in situ radiative observations and inferences are made concerning the cause of the discrepancies.

Stackhouse, Paul W., Jr.↗

Saltation threshold detection in a wind tunnel by the measurement of the net electrostatic charge

The Mars surface wind tunnel (MARSWIT) is an open circuit wind tunnel used for aeolian studies and is located inside a large vacuum chamber allowing testing at Martian surface atmospheric pressure. Since direct access is not available to the tunnel during operation at low pressure, a remote method of saltation detection is needed. The bed is observed by means of closed circuit video, but it is often difficult to determine the initiation of threshold. The measurement by means of an electrometer of the net electric charge produced by the saltating particles has provided a reliable means of saltation threshold detection. Saltating particles become charged several ways, both in wind tunnels and in a natural environment. The most significant of these methods are tribo-charging and contact charging, which always occur. Fracture charging may also occur under the high velocities associated with particle transport on Mars or under simulated Martian conditions. Detection in MARSWIT is achieved by allowing the saltating particles to impinge on a planar conducting surface normal to the flow that is connected to ground through a Keithly electrometer. The signal from the electrometer is connected to a strip chart recorder along with the analog signal from the pitot tube transducer that is used to determine the wind velocity in the tunnel. Thus, a record of wind velocity and the initiation of particle saltation is conveniently displayed together. While both positive and negative charges are produced during saltation, this method measures only the net charge; thus the charge may be either positive or negative depending upon the particles being tested, the size and size distribution of the test material, and the wind velocity. This has proven to be a very trustworthy and sensitive method of saltation threshold detection, being especially useful with the smaller sized particles which are the most difficult to observe visually.

Leach, Rodman N.↗

Properties of large area ErBa2Cu3O(7-x) thin films deposited by ionized cluster beams

ErBa2Cu3O(7-x) films have been produced by simultaneous deposition of Er, Ba, and Cu from three ionized cluster beam (ICB) sources at acceleration voltages of 0.3 to 0.5 kV. Combining ozone oxidation with ICB deposition at 650 C eliminated any need of post annealing processing. The substrates were rotated at 10 rotations per minute during the deposition which took place at a rate of about 3 to 4 nm. Films with areas up to 70 mm in diameter have been made by ICB deposition. These films, 100 nm thick, were deposited on SrTiO3 (100) substrates at 650 C in a mixture of six percent O3 in O2 at a total pressure of 4 x 10(exp -4) Torr. They had T(sub c) ranging from 84.3 K to 86.8 K over a 70 mm diameter and J(sub c) above 10(exp 6) A/sq cm at 77 K. X ray diffraction measurements of the three samples showed preferential c-axis orientation normal to the substrate surface. Scanning electron micrographs (SEM) of the three samples also show some texture dependence on sample position. For the three samples, there is a correlation between SEM texture, full width at half-maximum of rocking curves and J(sub c) versus temperature curves.

Levenson, L. L.↗

Surface analysis of anodized aluminum clamps from NASA-LDEF satellite

Surface analysis results of selected anodized aluminum clamps containing black (Z306) and white (A276) paints which received nearly six years of Low Earth Orbit (LEO) exposure on the Long Duration Exposure Facility are reported. Surface analytical techniques, including x-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES), and scanning electron microscopy/energy dispersive analysis by x-ray (SEM/EDAX), showed significant differences in the surface composition of these materials depending upon the position on the LDEF. Differences in the surface composition are attributed to varying amounts of atomic oxygen and vacuum ultraviolet radiation (VUV). Silicon containing compounds were the primary contaminant detected on the materials.

Grammer, H. L.↗

Experiments with phase change thermal energy storage canisters for Space Station Freedom

The solar dynamic power module proposed for the Space Station Freedom (SSF) uses the heat of fusion of a phase change material (PCM) to efficiently store thermal energy for use during eclipse periods. The PCM, a LiF-20CaF2 salt, is contained in annular, metal canisters located in a heat receiver at the focus of a solar concentrator. PCM canister ground-based experiments and analytical heat transfer studies are discussed. The hardware, test procedures, and test results from these experiments are discussed. After more than 900 simulated SSF orbital cycles, no canister cracks or leaks were observed and all data were successfully collected. The effect of 1-g test orientation on canister wall temperatures was generally small while void position was strongly dependent on test orientation and canister cooling. In one test orientation, alternating wall temperature data were measured that supports an earlier theory of oscillating vortex flow in the PCM melt. Analytical canister wall temperatures compared very favorably with experimental temperature data. This illustrates that ground-based canister thermal performance can be predicted well by analyses that employ straight-forward, engineering models of void behavior and liquid PCM free convection.

Kerslake, Thomas W.↗

Surface characterization of selected LDEF tray clamps

The surface characterization of chromic acid anodized 6061-T6 aluminum alloy tray clamps has shown differences in surface chemistry depending upon the position on the Long Duration Exposure Facility (LDEF). Water contact angle results showed no changes in wettability of the tray clamps. The overall surface topography of the control, trailing edge(E3) and leading edge(D9) samples was similar. The thickness of the aluminum oxide layer for all samples determined by Auger depth profiling was less than one micron. X-ray photoelectron spectroscopy (XPS) analysis of the tray clamps showed significant differences in the surface composition. Carbon and silicon containing compounds were the primary contaminants detected.

Cromer, T. F.↗

Crosstalk in solar polarization measurements

The instrumental crosstalk associated with the Marshall Space Flight Center Vector Magnetograph and the solar crosstalk created by the magnetic field are described and their impact on the reconstruction of the solar vector magnetic field is analyzed. It is pointed out that identifying and correcting the crosstalk is important in the development of realistic models describing the solar atmosphere. Solar crosstalk is spatially dependent on the structure of the magnetic field while instrumental crosstalk is dependent on the position of the analyzer.

West, E. A.↗

Signal-to-noise ratios in IUE low-dispersion spectra. II - Photometrically corrected images

Photometrically corrected images from the IUE's two intensified vidicon cameras are used to explore the character of detector noise, and a protocol for the derivation of realistic noise models is proposed on the basis of available collections of UV-Flood calibration images. The incomplete removal of the pixel-to-pixel sensitivity pattern can lead to a factor-of-2 enhancement in apparent noise; even with good suppression of pixel granularity, the remaining random noise can exhibit saturation behavior which causes S/N to cease improving with increasing exposure. When all relevant effects are considered, underlying, 'pristine' noise models show virtually no dependence on spatial position.

Ayres, Thomas R.↗

Measurement and characterization of force dynamics in high T(sub c) superconductors

Magnetic bearing implementations using more exotic superconducting phenomena have been proliferating in recent years because they have important advantages over conventional implementations. For example, the stable suspension of a six degrees-of-freedom object by superconducting means can be achieved without a control system and with the use of only a single superconductor. It follows that the construction becomes much simpler with decreased need for position sensors and stabilizers. However, it is recognized that the design of superconducting systems can be difficult because important characteristics relating to the 6 degree-of-freedom dynamics of an object suspended magnetically are not readily available and the underlying principles of superconducting phenomena are not yet completely understood. To eliminate some of the guesswork in the design process, this paper proposes a system which can resolve the mechanical properties of suspension by superconductivity and provide position and orientation dependent data about the system's damping, stiffness, and frequency response characteristics. This system employs an actively-controlled magnetically-suspended fine-motion device that can also be used as a six degree-of-freedom force sensor. By attaching the force sensor to a permanent magnet that is being levitated above a superconducting magnet, mechanical characteristics of the superconductor levitation can be extracted. Such information would prove useful for checking the validity of theoretical models and may even give insights into superconducting phenomena.

Higuchi, Toshiro↗

On acoustic radiation from a vibrating panel

An experimental and numerical study of the response and radiation from an acoustically loaded aircraft panel is presented. In the experiment, the panel is excited by a normally incident, harmonic wave. Measurements of the panel response and the resulting transmitted pressure are made in both the near- and acoustic far-fields. The numerical computations model the experiment and in particular account for the full coupling between the panel and the surrounding three dimensional acoustic fluid. The results demonstrate that for a sufficiently high excitation level, the panel response becomes nonlinear. The nonlinearity is characterized by the appearance of harmonics and subharmonics in the power spectral densities of the panel motion and consequently in the resulting acoustic radiation. The primary characteristic of the far-field acoustic radiation is the increase in harmonic content relative to the fundamental and subharmonics with increasing distance from the panel. This is shown to be a result of linear and weakly nonlinear wave propagation effects. The numerical results show that the radiated far-field pressure is strongly dependent on the position of the measurement point with respect to the panel center. The experimental and numerical results are in good qualitative agreement.

Frendi, Abdelkader↗

A Yohkoh search for `black-light flares'

Calculations which predict that a phenomenon analogous to stellar negative pre-flares could also exist on the Sun were published by Henoux et al. (1990), and Aboudarham et al., (1990), who showed at the beginning of a solar white-light flare (WLF) event an electron beam can cause a transient darkening before the WLF emission starts, under certain conditions. They named this event a `black light flare' (BLF). Such a BLF event should appear as diffuse dark patches lasting for about 20 seconds preceding the WLF emission, which would coincide with intense and impulsive hard X-ray bursts. The BLF location would be at (or in the vicinity of ) the forthcoming bright patches. Their predicted contrast depends on the position of the flare on the solar disk and on the wavelength band of the observation. The Yohkoh satellite provided white-light data from the aspect camera of the Soft X-ray Telescope (SXT) instrument (Tsuneta et al., 1991), at 431 nm and with a typical image interval of 10 - 12 s. We have studied nine white-light flares observed with this instrument, with X-ray class larger than M6. We have found a few interesting episodes, but no unambiguous example of the predicted BLF event. This study, although the best survey to date, was not ideal from the observational point of view. We therefore encourage further searches. Successful observations of this phenomenon on the Sun would greatly strengthen our knowledge of the lower solar atmosphere and its effects on solar luminosity variations.

Van Driel-Gesztelyi, Lidia↗