Search NASA⌕ Search

SEARCH · Search NASA

Results for “scanning electron diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Excess Conductivity Investigation of Y{sub 3}Ba{sub 5}Cu{sub 8}O{sub 18±δ} Superconductors Prepared by Various Parameters of Planetary Ball Milling Technique

Superconducting samples of type Y{sub 3}Ba{sub 5}Cu{sub 8}O{sub 18±δ} were elaborated by using a planetary high-energy ball milling (HEBM) technique with various parameters. Phases, microstructure, and superconductivity have been examined using X-ray powder diffraction (XRD), scanning electron microscopy (SEM), and electrical resistivity measurements. SEM investigation shows the occurrence of nanoentities embedded into the superconducting matrix for samples prepared by a ball milling technique. The main objective of this study is to investigate the influence of ball milling parameters on the fluctuation-induced conductivity (FIC). The electrical resistivity versus temperature, ρ(T), above T{sub c} was analyzed using Lawrence–Doniach (LD) and Aslamazov–Larkin (AL) models. Different fluctuation regimes indicated by short-wave fluctuation (SWF) and three-dimensional (3D), two-dimensional (2D), one-dimensional (1D), and critical region (CR) fluctuations were identified. The coherence length at zero temperature, the effective layer thickness, the critical magnetic fields, and the critical current densities are determined. The superconducting parameters strongly depend on the planetary ball milling technique, and the results are explained in relevancy to the microstructure. It was found that the achievement of a microstructure with well-dispersed nanoentities is an effective way for introducing pinning centers for enhancing critical current density and flux pinning capability of bulk Y-358.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of bath temperatures on physical and electrical properties of potentiostatically deposited Cu{sub 2}O thin films for heterojunction solar cell applications

In the present work, the influence of bath temperatures on structural, morphological, vibrational, optical, electrical and photo response properties of the electrochemically deposited cuprous oxide (Cu{sub 2}O) thin films on fluorine doped tin oxide substrate is extensively investigated with the help of X-ray diffraction (XRD), scanning electron microscopy (SEM), Micro Raman spectroscopy, photo luminescence (PL) spectroscopy, UV–visible spectroscopy, LCR measurement, Keithley 4200 semiconductor characterization system respectively. XRD patterns reveal that the deposited Cu{sub 2}O films have cubic structure grown along the preferential (111) orientation and the film deposited at 40 °C shows better crystalline nature when compared at 55 and 70 °C. The micro structural properties of films such as crystallite size (D), dislocation density (δ), micro strain (ε) and stacking fault probability (α) were calculated and discussed in detail. SEM displays a well-defined three side pyramid shaped morphology for the film deposited at 40 °C. Micro Raman and PL spectra reveal the film deposited at 40 °C by being better crystalline at a higher acceptor concentration. UV–Visible study shows that the optical energy band gap increases from 2.05 to 2.17 eV with an increase in bath temperature from 40 to 70 °C. The frequency-temperature dependence of impedance analysis shows a higher electrical conductivity for a film deposited at 40 °C compared to other bath temperatures. I-V measurement illustrates a good photoconductivity response for Cu{sub 2}O thin film deposited at 40 °C compared to films deposited at 55 and 70 °C.

36 MATERIALS SCIENCE↗

Ultrasound-assisted facile synthesis of a new tantalum(V) metal-organic framework nanostructure: Design, characterization, systematic study, and CO{sub 2} adsorption performance

This work presents a fast route for the preparation of a new Ta(V) metal-organic framework nanostructure with high surface area, significant porosity, and small size distribution. X-ray diffraction (XRD), scanning electron microscopy (SEM), Transition electron microscopy (TEM), energy dispersive spectrometer (EDS), thermo-gravimetric analysis (TGA), differential scanning calorimetry (DSC), fourier transform infrared spectroscopy (FTIR), CHNS/O elemental analyser, and Brunauer-Emmett-Teller (BET) surface area analysis were applied to characterize the synthesized product. Moreover, the influences of ultrasonic irradiation including temperature, time, and power on different features of the final products were systematically studied using 2{sup k-1} factorial design experiments, and the response surface optimization was used for determining the best welding parameter combination. The results obtained from analyses of variances showed that ultrasonic parameters affected the size distribution, thermal behaviour, and surface area of Ta-MOF samples. Based on response surface methodology, Ta-MOF could be obtained with mean diameter of 55 nm, thermal stability of 228 °C, and high surface area of 2100 m{sup 2}/g. The results revealed that the synthesized products could be utilized in various applications such as a novel candidate for CO{sub 2} adsorption. - Graphical abstract: A facile route was used for fabrication of a new metal -organic framework based on tantalum nanostructures that have high surface area, considerable porosity, homogenous morphology, and small size distribution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Efficient photocatalytic degradation of gaseous formaldehyde by the TiO{sub 2}/tourmaline composites

Graphical abstract: - Highlights: • The TiO{sub 2}/tourmaline composites were prepared by a sol–gel method. • The composites exhibited excellent photocatalytic activity and good stability. • The physicochemical property of tourmaline may be favor for the degradation of HCHO. • The mixed-phase of anatase and rutile TiO{sub 2} may be favor for the degradation of HCHO. - Abstract: The TiO{sub 2} supported tourmaline composites were prepared by a sol–gel method and used as a photocatalyst for the degradation of formaldehyde (HCHO). The composites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), N{sub 2} adsorption–desorption, Fourier transform infrared (FT-IR) spectroscopy and UV–vis diffuse reflectance spectroscopy (UV–vis DRS). The results indicate that the mixed-phase of anatase and rutile exists in the TiO{sub 2}/tourmaline composites. The specific surface area of the TiO{sub 2}/tourmaline composites is much higher than that of the pure TiO{sub 2}. The TiO{sub 2}/tourmaline composites exhibited excellent photocatalytic activity for the degradation of HCHO, which was 6 times higher than that of the pure TiO{sub 2}. Moreover, the excellent photocatalytic activity of the composites was fully maintained after five photocatalytic cycles, which may be attributed to the physicochemical property of tourmaline and the mixed-phase of anatase and rutile in the TiO{sub 2}/tourmaline composites.

36 MATERIALS SCIENCE↗

AgI/Ag{sub 3}PO{sub 4} hybrids with highly efficient visible-light driven photocatalytic activity

Highlights: • AgI/Ag{sub 3}PO{sub 4} hybrid was prepared via an in situ anion-exchange method. • AgI/Ag{sub 3}PO{sub 4} displays the excellent photocatalytic activity under visible light. • AgI/Ag{sub 3}PO{sub 4} readily transforms to be Ag@AgI/Ag{sub 3}PO{sub 4} system. • h{sup +} and O{sub 2}{sup ·−} play the major role in the AO 7 decolorization over AgI/Ag{sub 3}PO{sub 4}. • The activity enhancement is ascribed to a Z-scheme system composed of Ag{sub 3}PO{sub 4}, Ag and AgI. - Abstract: Highly efficient visible-light-driven AgI/Ag{sub 3}PO{sub 4} hybrid photocatalysts with different mole ratios of AgI were prepared via an in situ anion-exchange method and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), UV–vis diffuse reflectance spectroscopy (DRS) and photoluminescence (PL) technique. Under visible light irradiation (>420 nm), the AgI/Ag{sub 3}PO{sub 4} photocatalysts displayed the higher photocatalytic activity than pure Ag{sub 3}PO{sub 4} and AgI for the decolorization of acid orange 7 (AO 7). Among the hybrid photocatalysts, AgI/Ag{sub 3}PO{sub 4} with 80% of AgI exhibited the highest photocatalytic activity for the decolorization of AO 7. X-ray photoelectron spectroscopy (XPS) results revealed that AgI/Ag{sub 3}PO{sub 4} readily transformed to be Ag@AgI/Ag{sub 3}PO{sub 4} system while the photocatalytic activity of AgI/Ag{sub 3}PO{sub 4} remained after 5 recycling runs. In addition, the quenching effects of different scavengers displayed that the reactive h{sup +} and O{sub 2}{sup ·−} play the major role in the AO 7 decolorization. The photocatalytic activity enhancement of AgI/Ag{sub 3}PO{sub 4} hybrids can be ascribed to the efficient separation of electron–hole pairs through a Z-scheme system composed of Ag{sub 3}PO{sub 4}, Ag and AgI, in which Ag nanoparticles act as the charge separation center.

36 MATERIALS SCIENCE↗

Synthesis and photoactivity enhancement of Ba doped Bi{sub 2}WO{sub 6} photocatalyst

Highlights: • The Ba-doped Bi{sub 2}WO{sub 6} photocatalyst have been synthesized by a hydrothermal route. • The photocatalytic activity of Bi{sub 2}WO{sub 6} was greatly enhanced by Ba-doping. • The effect of Ba on the catalytic activity of Bi{sub 2}WO{sub 6} was studied and discussed. - Abstract: In this study, Bi{sub 2}WO{sub 6} doped with different barium contents were successfully prepared by a simple hydrothermal route at 180 °C for 12 h. The as-synthesized samples were characterized in detailed by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV–vis diffusere flectance spectroscopy (UV–vis DRS) and Brunauer–Emmet–Teller (BET) theory. Their photocatalytic activities were evaluated by photodegradation of Rhodamine B (RhB) under simulated solar light. As a result, the photocatalytic properties were enhanced after Ba doping and the Ba-doped Bi{sub 2}WO{sub 6} with R{sub Ba} = 0.15 showed the highest photocatalytic activities of 96.3% RhB was decomposed in 50 min. Close investigation revealed that the proper Ba doped into Bi{sub 2}WO{sub 6} could not only increases its BET surface area, decrease its crystalline size, but also act as electron traps and facilitate the separation of photogenerated electron–hole pairs. The mechanism of enhanced photocatalytic activities of Ba-doped Bi{sub 2}WO{sub 6} were further investigated.

36 MATERIALS SCIENCE↗

Oriented and ordered mesoporous ZrO{sub 2}/TiO{sub 2} fibers with well-organized linear and spring structure

Graphical abstract: The ultra-stable order mesoporous ZrO{sub 2}/TiO{sub 2} fibers with well-organized linear and spring structure and large surface area under higher temperatures were prepared by a simple EISA process. - Highlights: • The ZrO{sub 2}/TiO{sub 2} fibers were prepared by EISA process combined with steam heat-treatment. • The mesoporous ZrO{sub 2}/TiO{sub 2} fibers have well-organized linear and spring structure. • The fibers were composed of oval rod nanocrystals of ZrTiO{sub 4}. - Abstract: The ultra-stable order mesoporous ZrO{sub 2}/TiO{sub 2} fibers with well-organized linear and spring structure and large surface areas under higher temperatures were prepared by a (simple evaporation-induced assembly) EISA process. The preparation, microstructures and formation processes were characterized by Fourier transformation infrared (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and N{sub 2} adsorption–absorption measurements. The fibers take on pinstripe configuration which is very orderly along or perpendicular to the axial direction of the fibers. The diameters of the pinstripe are in the region of 200–400 nm and arranges regularly, which are composed of oval rod nanocrystals of ZrTiO{sub 4}.

36 MATERIALS SCIENCE↗

Phase transition and negative thermal expansion of HfMnMo3O12

Highlights: • HfMnMo{sub 3}O{sub 12} exhibits negative thermal expansion from 373 K to 773 K. • The linear CTE of HfMnMo{sub 3}O{sub 12} is −3.8 × 10{sup −6} K{sup −1}. • Vibrational modes corresponding to librational and translational motions of the polyhedra are observed. - Abstract: A novel compound HfMnMo{sub 3}O{sub 12} with negative thermal expansion (NTE) was synthesized using solid state method. The crystal structure, fracture morphology and NTE properties of the material were investigated by temperature-dependent X-ray diffraction (XRD), scanning electron microscope (SEM) and temperature-dependent Raman spectra. Our experimental results show that the compound adopts a monoclinic symmetry below room temperature and transforms to an orthorhombic phase above 348 K. In the orthorhombic phase the compound exhibits NTE property with a linear coefficient of thermal expansion (CTE) −3.8 × 10{sup −6} K{sup −1} from 400 K to 700 K. The physical mechanism of the NTE is discussed and elucidated according to our experiments.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Substrate nitridation induced modulations in transport properties of wurtzite GaN/p-Si (100) heterojunctions grown by molecular beam epitaxy

Phase pure wurtzite GaN films were grown on Si (100) substrates by introducing a silicon nitride layer followed by low temperature GaN growth as buffer layers. GaN films grown directly on Si (100) were found to be phase mixtured, containing both cubic ({beta}) and hexagonal ({alpha}) modifications. The x-ray diffraction (XRD), scanning electron microscopy (SEM), photoluminescence (PL) spectroscopy studies reveal that the significant enhancement in the structural as well as in the optical properties of GaN films grown with silicon nitride buffer layer grown at 800 deg. C when compared to the samples grown in the absence of silicon nitride buffer layer and with silicon nitride buffer layer grown at 600 deg. C. Core-level photoelectron spectroscopy of Si{sub x}N{sub y} layers reveals the sources for superior qualities of GaN epilayers grown with the high temperature substrate nitridation process. The discussion has been carried out on the typical inverted rectification behavior exhibited by n-GaN/p-Si heterojunctions. Considerable modulation in the transport mechanism was observed with the nitridation conditions. The heterojunction fabricated with the sample of substrate nitridation at high temperature exhibited superior rectifying nature with reduced trap concentrations. Lowest ideality factors ({approx}1.5) were observed in the heterojunctions grown with high temperature substrate nitridation which is attributed to the recombination tunneling at the space charge region transport mechanism at lower voltages and at higher voltages space charge limited current conduction is the dominating transport mechanism. Whereas, thermally generated carrier tunneling and recombination tunneling are the dominating transport mechanisms in the heterojunctions grown without substrate nitridation and low temperature substrate nitridation, respectively.

36 MATERIALS SCIENCE↗

Composite electrolyte with proton conductivity for low-temperature solid oxide fuel cell

In the present work, cost-effective nanocomposite electrolyte (Ba-SDC) oxide is developed for efficient low-temperature solid oxide fuel cells (LTSOFCs). Analysis has shown that dual phase conduction of O{sup −2} (oxygen ions) and H{sup +} (protons) plays a significant role in the development of advanced LTSOFCs. Comparatively high proton ion conductivity (0.19 s/cm) for LTSOFCs was achieved at low temperature (460 °C). In this article, the ionic conduction behaviour of LTSOFCs is explained by carrying out electrochemical impedance spectroscopy measurements. Further, the phase and structure analysis are investigated by X-ray diffraction and scanning electron microscopy techniques. Finally, we achieved an ionic transport number of the composite electrolyte for LTSOFCs as high as 0.95 and energy and power density of 90% and 550 mW/cm{sup 2}, respectively, after sintering the composite electrolyte at 800 °C for 4 h, which is promising. Our current effort toward the development of an efficient, green, low-temperature solid oxide fuel cell with the incorporation of high proton conductivity composite electrolyte may open frontiers in the fields of energy and fuel cell technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tuning the metal-insulator transition via epitaxial strain and Co doping in NdNiO{sub 3} thin films grown by polymer-assisted deposition

The epitaxial NdNi{sub 1-x}Co{sub x}O{sub 3} (0 ≤ x ≤ 0.10) thin films on (001) LaAlO{sub 3} and (001) SrTiO{sub 3} substrates were grown by a simple polymer-assisted deposition technique. The co-function of the epitaxial strain and Co doping on the metal-insulator transition in perovskite nickelate NdNiO{sub 3} thin films is investigated. X-ray diffraction and scanning electron microscopy reveal that the as-prepared thin films exhibit good crystallinity and heteroepitaxy. The temperature dependent resistivities of the thin films indicate that both the epitaxial strain and Co doping lower the metal-insulator (MI) transition temperature, which can be treated as a way to tune the MI transition. Furthermore, under the investigated Co-doping levels, the MI transition temperature (T{sub MI}) shifts to low temperatures with Co content increasing under both compressive and tensile strain, and the more distinction is in the former situation. When x is increased up to 0.10, the insulating phase is completely suppressed under the compressive strain. With the strain increases from compression to tension, the resistivities are enhanced both in the metal and insulating regions. However, the Co-doping effect on the resistivity shows a more complex situation. As Co content x increases from zero to 0.10, the resistivities are reduced both in the metal and insulating regions under the tensile strain, whereas they are enhanced in the high-temperature metal region under the compressive strain. Based on the temperature dependent resistivity in the metal regions, it is suggested that the electron-phonon coupling in the films becomes weaker with the increase of both the strain and Co-doping.

36 MATERIALS SCIENCE↗

The effect of milling time on the synthesis of Cu{sub 54}Mg{sub 22}Ti{sub 18}Ni{sub 6} alloy

In the present work, nanocrystalline Cu{sub 54}Mg{sub 22}Ti{sub 18}Ni{sub 6} alloy was produced by mechanical alloying from mixtures of pure crystalline Cu, Mg, Ti and Ni powders using a Fritsch planetary ball mill with a ball to powder ratio of 10:1. Morphological changes, microstructural evolution and thermal behaviour of the Cu-Mg-Ti-Ni powders at different stages of milling were characterised by X-ray diffraction (XRD), scanning electron microscopy with energy-dispersive X-ray detection (SEM/EDX) and differential thermal analysis (DTA). This alloy resulted in formation of single phase solid solution with FCC structure α-Cu (Mg, Ti, Ni) after 80 h of milling. In the initial stage of milling different sized and shaped elemental powders became uniform during mechanical alloying. The homogeneity of the Cu{sub 54}Mg{sub 22}Ti{sub 18}Ni{sub 6} alloy increased with increasing milling time. The EDX result also confirmed the compositional homogeneity of the powder alloy. The crystallite size of alloy was calculated below 10 nm from XRD data.

36 MATERIALS SCIENCE↗

Shock wave induced martensitic transformations and morphology changes in Fe-Pd ferromagnetic shape memory alloy thin films

Combining experimental methods and classical molecular dynamics (MD) computer simulations, we explore the martensitic transformation in Fe{sub 70}Pd{sub 30} ferromagnetic shape memory alloy thin films induced by laser shock peening. X-ray diffraction and scanning electron microscope measurements at shock wave pressures of up to 2.5 GPa reveal formation of martensitic variants with preferred orientation of the shorter c-axis of the tetragonal unit cell perpendicular to the surface plane. Moreover, consequential merging of growth islands on the film surface is observed. MD simulations unveil the underlying physics that are characterized by an austenite-martensite transformation with a preferential alignment of the c-axis along the propagation direction of the shock wave, resulting in flattening and in-plane expansion of surface features.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Pulsed laser deposition growth of heteroepitaxial YBa2Cu3O7/La0.67Ca0.33MnO3 superlattices on NdGaO3 and Sr0.7La0.3Al0.65Ta0.35O3 substrates

Heteroepitaxial superlattices of [YBa{sub 2}Cu{sub 3}O{sub 7}(n)/La{sub 0.67}Ca{sub 0.33}MnO{sub 3}(m)]{sub x} (YBCO/LCMO), where n and m are the number of YBCO and LCMO monolayers and x the number of bilayer repetitions, have been grown with pulsed laser deposition on NdGaO{sub 3} (110) and Sr{sub 0.7}La{sub 0.3}Al{sub 0.65}Ta{sub 0.35}O{sub 3} (001). These substrates are well lattice matched with YBCO and LCMO and, unlike the commonly used SrTiO{sub 3}, they do not give rise to complex and uncontrolled strain effects at low temperature. The growth dynamics and the structure have been studied in situ with reflection high-energy electron diffraction and ex situ with scanning transmission electron microscopy, x-ray diffraction, and neutron reflectometry. The individual layers are found to be flat and continuous over long lateral distances with sharp and coherent interfaces and with a well-defined thickness of the individual layer. The only visible defects are antiphase boundaries in the YBCO layers that originate from perovskite unit-cell height steps at the interfaces with the LCMO layers. We also find that the first YBCO monolayer at the interface with LCMO has an unusual growth dynamics and is lacking the CuO chain layer, while the subsequent YBCO layers have the regular Y-123 structure. Accordingly, the CuO{sub 2} bilayers at both the LCMO/YBCO and the YBCO/LCMO interfaces are lacking one of their neighboring CuO chain layers and, thus, half of their hole-doping reservoir. Nevertheless, from electric transport measurements on a superlattice with n = 2 we obtain evidence that the interfacial CuO{sub 2} bilayers remain conducting and even exhibit the onset of a superconducting transition at very low temperature. Finally, we show from dc magnetization and neutron reflectometry measurements that the LCMO layers are strongly ferromagnetic.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

TOF SIMS analysis and generation of white photoluminescence from strontium silicate codoped with europium and terbium

White light emitting terbium (Tb{sup 3+}) and europium (Eu{sup 3+}) codoped strontium silicate (Sr{sub 2}SiO{sub 4}) phosphors were prepared by a solid state reaction process. The structure, particle morphology, chemical composition, ion distribution, photoluminescence (PL), and decay characteristics of the phosphors were analyzed by x-ray diffraction (XRD), scanning electron microscopy (SEM), time-of-flight secondary ion mass spectrometry (TOF-SIMS), and PL spectroscopy, respectively. The XRD data showed that our Sr{sub 2}SiO{sub 4} composed of two phases, namely, β-Sr{sub 2}SiO{sub 4} and α′-Sr{sub 2}SiO{sub 4}, and the α′-Sr{sub 2}SiO{sub 4} phase was more prominent than the β-Sr{sub 2}SiO{sub 4} phase. The SEM micrographs showed that the particles were agglomerated together and they did not have definite shapes. All ions (i.e., negative and positive) present in our materials were identified by TOF-SIMS. In addition, the chemical imaging performed with the TOF-SIMS demonstrated how the individual ions including the dopants (Eu{sup 3+} and Tb{sup 3+}) were distributed in the host lattice. White photoluminescence was observed when the Sr{sub 2}SiO{sub 4}:Tb{sup 3+}, Eu{sup 3+} phosphor was excited at 239 nm using a monochromatized xenon lamp as the excitation source. The phosphor exhibited fast decay lifetimes implying that it is not a good candidate for long afterglow applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Hydrothermal synthesis of cerium titanate nanorods and its application in visible light photocatalysis

Highlights: • Cerium titanate nanorods have been synthesized by a simple hydrothermal process. • The size of the cerium titanate nanorods can be controlled by growth conditions. • Cerium titanate nanorods exhibit good photocatalytic activities for methyl blue. - Abstract: Cerium titanate nanorods have been prepared via a hydrothermal process using sodium dodecyl sulfate (SDS) as the surfactant. The cerium titanate nanorods have been analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), and ultraviolet–visible (UV–vis) diffuse reflectance spectrum. XRD shows that the nanorods are composed of CeTi{sub 21}O{sub 38} phase. Electron microscopy observations indicate that the nanorods have good single crystalline nature. The diameter and length of the nanorods are about 50–200 nm and 1–2 μm, respectively. Cerium titanate nanorods have a band gap of 2.65 eV. The photocatalytic activities of the nanorods have been investigated by degrading methylene blue (MB) under visible light irradiation. MB solution with the concentration of 10 mg L{sup −1} can be degraded totally with the irradiation time increasing to 240 min. Cerium titanate nanorods exhibit great potential in photocatalytic degradation of MB under visible light irradiation.

36 MATERIALS SCIENCE↗

Facile fabrication of rutile monolayer films consisting of well crystalline nanorods by following an IL-assisted hydrothermal route

In this study, rutile films consisting of rectangular nanorods were facilely deposited on glass substrates from strongly acid solution of TiCl{sub 4}. The highly ordered array of nanorods was realized in presence of ionic liquid (IL) of [Bmim]Br by following a hydrothermal process. In this process, Degussa P25 nanoparticles served as seeds that were pre-deposited on the substrates to facilitate the array of rutile nanorods. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Raman spectrum were used to characterize the obtained nanorod films. The measurements showed that the nanorods were rectangular with width of 100-200 nm and length of more than 1 {mu}m, and grew up typically along c-axis to form the arrays against the substrate. The presence of IL was found vital for the formation of rutile nanorods, and the suitable molar ratio of [Bmim]Br to TiCl{sub 4} ranged from 500:1 to 1500:1. The excessive [Bmim]Br may hinder the precipitation of rutile particles. - Graphical abstract: The rutile film consisting of rectangular nanorods is successfully deposited on glass substrate in presence of ionic liquid (IL) of [Bmim]Br. The nanorods were rectangular with width of 100-200 nm and length of more than 1 {mu}m, which grew up typically along c-axis to form the arrays against the substrate.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Photoluminescence in Pb{sub 0.95}Sr{sub 0.05}(Zr{sub 1−x}Ti{sub x}){sub 1−y}Cr{sub y}O{sub 3} ferroelectric ceramic system

Over the past several years, there has been a remarkable growth and development in new ceramic and/or composite materials to be used in the electro-electronic industry. Ferroelectric materials have been recognized for their multifunctional physical properties; also, their optical properties are a subject of intense research effort due to their possible electro-optic applications. In this work, the visible photoluminescence effect is analyzed at room temperature in a sintered Pb{sub 0.95}Sr{sub 0.05}(Zr{sub 1−x}Ti{sub x}){sub 1−y}Cr{sub y}O{sub 3} perovskite-type structure system, doped with Sr and Cr. The excitation bands used were 267, 325, 373, 457, 635, and 680 nm, but the best result was obtained at 373 nm. The intensity and energy of such emission in this system have been studied by changing the molar Cr concentration (0 < y < 0.005) and the Ti content (x), with x = 0.20, 0.40, 0.53, 0.60, and 0.80, on both sides of the morphotropic phase boundary (MPB) zone. The principal emission bands are at the energies 1.73, 1.87, and 3.03 eV. The changes that were caused by Zr or Ti ions in the symmetry presented in the rhombohedral or tetragonal side of the MPB are more important. Additionally, structural and micro-structural measurements were performed by the x-ray diffraction and scanning electron microscopy techniques, respectively. The micro-Raman technique is also used in the study of this set of samples, which allows finding the Raman shift modes and the influence on the structural changes of the dopants.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗