Search NASA⌕ Search

SEARCH · Search NASA

Results for “ATOMIC MODELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Dislocation and Structural Studies at Metal–Metallic Glass Interface at Low Temperature

In this paper, molecular dynamics (MD) simulation deformation studies on the Al (metal)–Cu{sub 50}Zr{sub 50} (metallic glass) model interface is carried out based on cohesive zone model. The interface is subjected to mode-I loading at a strain rate of 10{sup 9} s{sup −1} and temperature of 100 K. The dislocations reactions and evolution of dislocation densities during the deformation have been investigated. Atomic interactions between Al, Cu and Zr atoms are modeled using EAM (embedded atom method) potential, and a timestep of 0.002 ps is used for performing the MD simulations. A circular crack and rectangular notch are introduced at the interface to investigate the effect on the deformation behavior and fracture. Further, scale size effect is also investigated. The structural changes and evolution of dislocation density are also examined. It is found that the dominant deformation mechanism is by Shockley partial dislocation nucleation. Amorphization is observed in the Al regions close to the interface and occurs at a lower strain in the presence of a crack. The total dislocation density is found to be maximum after the first yield in both the perfect and defect interface models and is highest in the case of perfect interface with a density of 6.31 × 10{sup 17} m{sup −2}. In the perfect and circular crack defect interface models, it is observed that the fraction of Shockley partial dislocation density decreases, whereas that of strain rod dislocations increases with increase in strain.

36 MATERIALS SCIENCE↗

Numerical and experimental study of atomic transport and Balmer line intensity in Linac4 negative ion source

Time structure of Balmer H{sub α} line intensity in Linac4 RF plasma has been analyzed by the combined simulation model of atomic transport and Collisional-Radiative models. As a preliminary result, time variation of the line intensity in the ignition phase of RF plasma is calculated and compared with the experimental results by photometry. For the comparison, spatial distribution of the local H{sub α} photon emission rate at each time is calculated from the numerical model. The contribution of the local photon emission rates to the observed line intensity via optical viewing port is also investigated by application of the mock-up of the optical viewing port and the known light source. It has been clarified from the analyses that the higher and the lower peaks of the H{sub α} line intensity observed during 1 RF cycle is mainly due to the different spatial distributions in the electron energy distribution function and the resultant local photon emission rate. These results support previous suggestion that the existence of the capacitive electric field in axial direction leads to the higher/lower peaks of the line intensity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Shadow Molecular Dynamics and Atomic Cluster Expansions for Flexible Charge Models

Here, a shadow molecular dynamics scheme for flexible charge models is presented where the shadow Born–Oppenheimer potential is derived from a coarse-grained approximation of range-separated density functional theory. The interatomic potential, including the atomic electronegativities and the charge-independent short-range part of the potential and force terms, is modeled by the linear atomic cluster expansion (ACE), which provides a computationally efficient alternative to many machine learning methods. The shadow molecular dynamics scheme is based on extended Lagrangian (XL) Born–Oppenheimer molecular dynamics (BOMD). XL-BOMD provides stable dynamics while avoiding the costly computational overhead associated with solving an all-to-all system of equations, which normally is required to determine the relaxed electronic ground state prior to each force evaluation. To demonstrate the proposed shadow molecular dynamics scheme for flexible charge models using atomic cluster expansion, we emulate the dynamics generated from self-consistent charge density functional tight-binding (SCC-DFTB) theory using a second-order charge equilibration (QEq) model. The charge-independent potentials and electronegativities of the QEq model are trained for a supercell of uranium oxide (UO 2 ) and a molecular system of liquid water. The combined ACE+XL-QEq molecular dynamics simulations are stable over a wide range of temperatures both for the oxide and for the molecular systems and provide a precise sampling of the Born–Oppenheimer potential energy surfaces. Accurate ground Coulomb energies are produced by the ACE-based electronegativity model during an NVE simulation of UO 2 , predicted to be within 1 meV of those from SCC-DFTB on average during comparable simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The ANI-1ccx and ANI-1x data sets, coupled-cluster and density functional theory properties for molecules

Abstract Maximum diversification of data is a central theme in building generalized and accurate machine learning (ML) models. In chemistry, ML has been used to develop models for predicting molecular properties, for example quantum mechanics (QM) calculated potential energy surfaces and atomic charge models. The ANI-1x and ANI-1ccx ML-based general-purpose potentials for organic molecules were developed through active learning; an automated data diversification process. Here, we describe the ANI-1x and ANI-1ccx data sets. To demonstrate data diversity, we visualize it with a dimensionality reduction scheme, and contrast against existing data sets. The ANI-1x data set contains multiple QM properties from 5 M density functional theory calculations, while the ANI-1ccx data set contains 500 k data points obtained with an accurate CCSD(T)/CBS extrapolation. Approximately 14 million CPU core-hours were expended to generate this data. Multiple QM calculated properties for the chemical elements C, H, N, and O are provided: energies, atomic forces, multipole moments, atomic charges, etc. We provide this data to the community to aid research and development of ML models for chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Systematic Evaluation of Counterpoise Correction in Density Functional Theory

A widespread belief persists that the Boys–Bernardi function counterpoise (CP) procedure “overcorrects” supramolecular interaction energies for the effects of basis-set superposition error. To the extent that this is true for correlated wave function methods, it is usually an artifact of low-quality basis sets. The question has not been considered systematically in the context of density functional theory, however, where basis-set convergence is generally less problematic. We present a systematic assessment of the CP procedure for a representative set of functionals and basis sets, considering both benchmark data sets of small dimers and larger supramolecular complexes. The latter include layered composite polymers with ~150 atoms and ligand–protein models with ~300 atoms. Provided that CP correction is used, we find that intermolecular interaction energies of nearly complete-basis quality can be obtained using only double-ζ basis sets. Furthermore, this is less expensive as compared to triple-ζ basis sets without CP correction. CP-corrected interaction energies are less sensitive to the presence of diffuse basis functions as compared to uncorrected energies, which is important because diffuse functions are expensive and often numerically problematic for large systems. Our results upend the conventional wisdom that CP “overcorrects” for basis-set incompleteness. In small basis sets, CP correction is mandatory in order to demonstrate that the results do not rest on error cancellation.

74 ATOMIC AND MOLECULAR PHYSICS↗

Molecular dynamics study of mechanical properties of carbon nanotube reinforced aluminum composites

Atomistic simulations were conducted to estimate the effect of the carbon nanotube (CNT) reinforcement on the mechanical behavior of CNT-reinforced aluminum (Al) nanocomposite. The periodic system of CNT-Al nanocomposite was built and simulated using molecular dynamics (MD) software LAMMPS (Large-scale Atomic/Molecular Massively Parallel Simulator). The mechanical properties of the nanocomposite were investigated by the application of uniaxial load on one end of the representative volume element (RVE) and fixing the other end. The interactions between the atoms of Al were modeled using embedded atom method (EAM) potentials, whereas Adaptive Intermolecular Reactive Empirical Bond Order (AIREBO) potential was used for the interactions among carbon atoms and these pair potentials are coupled with the Lennard-Jones (LJ) potential. The results show that the incorporation of CNT into the Al matrix can increase the Young’s modulus of the nanocomposite substantially. In the present case, i.e. for approximately 9 with % reinforcement of CNT can increase the axial Young’s modulus of the Al matrix up to 77 % as compared to pure Al.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Population inversion in a magnetized hydrogen plasma expansion as a consequence of the molecular mutual neutralization process

A weakly magnetized expanding hydrogen plasma, created by a cascaded arc, was investigated using optical emission spectroscopy. The emission of the expanding plasma is dominated by H{sub {alpha}} emission in the first part of the plasma expansion, after which a sharp transition to a blue afterglow is observed. The position of this sharp transition along the expansion axis depends on the magnetic field strength. The blue afterglow emission is associated with population inversion of the electronically excited atomic hydrogen states n=4-6 with respect to n=3. By comparing the measured densities with the densities using an atomic collisional radiative model, we conclude that atomic recombination processes cannot account for the large population densities observed. Therefore, molecular processes must be important for the formation of excited states and for the occurrence of population inversion. This is further corroborated at the transition from red to blue, where a hollow profile of the excited states n=4-6 in the radial direction is observed. This hollow profile is explained by the molecular mutual neutralization process of H{sub 2}{sup +} with H{sup -}, which has a maximum production for excited atomic hydrogen 1-2 cm outside the plasma center.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The influence of intake flow and coolant temperature on gasoline spray morphology during early-injection DISI engine operation

Multi-hole gasoline injectors operating at conditions spanning throttled early-intake stroke operation produce spray plumes that either remained separated or merge and collapse due to flash boiling. Flash boiling occurs due to the sudden expansion of gas bubbles in the liquid fuel at high fuel temperature and low ambient pressure. This study records high-speed images of spray-morphology changes due to in-cylinder flow, thereby revealing operating conditions that do and do not affect the self-induced morphology observed in quiescent vessels. Specifically, in a central-injection, four-valve, high-tumble engine, where the thermodynamic state and in-cylinder cross flow are dynamic. Motivated by cold start and hot restart operation, the fuel pressure, coolant temperature, in-cylinder air pressure, and engine rpm were systematically varied over relevant operating conditions, which bracketed the range from non- to flash-boiling sprays. The results reveal the operating conditions at which the in-cylinder cross flow disrupts the spray morphology as well as the extent of the disruption. At 650 rpm, the spray morphology was similar to that observed in quiescent vessels at nominally equivalent fuel temperature and in-cylinder pressure, indicating that the spray’s self-induced entrainment flow dominated the in-cylinder flow. However, for fuel temperature and ambient pressure near the transition between non- and flash-boiling, the intake cross flow at higher engine speed (1950 rpm) significantly disrupted the spray morphology. The high cross-flow velocity appears to induce plume merging and collapse, whereas none was evident at low rpm (650 rpm). This study led to the postulate that the spray merging and collapse are governed by the rate of atomization near the nozzle exit, presumed to be controlled by either or both aerodynamic atomization and flash-boiling intensity. It would then follow that spray modeling in CFD requires atomization models that blend the effects of both physical processes.

42 ENGINEERING↗

Multiphysics Simulations of MSRE with NEAMS Thermal Hydraulics Tools

This report documents the benchmarks being developed and simulations performed using tools and codes developed under the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, utilizing MSRE experimental data. In FY23, three main work scopes were investigated under the NEAMS MSR work package at ANL. The first scope investigated the Griffin-SAM coupling model for simulating the pump startup transient experiment of MSRE. The analyses start with a simple model (single-channel, single-lattice), gradually adding more details (multi-channel, full-core) into the model. The results show that the reactivity loss curve is very sensitive to the axial boundary conditions and the radial core discretization. The simple model can predict a similar reactivity trend as that of the more sophisticated model, which is likely due to error cancellation. Accurately modeling the axial boundary condition may further improve the reactivity trend but would require significant efforts to generate the mesh of the MSRE inlet and upper plenum. The core channel radial discretization for the Griffin-SAM coupled model also depends on the flow distribution. Given the complex geometry in the inlet plenum, the flow distribution needed to be calculated from CFD analysis, which was performed using the NekRS code. This analysis employed a MSRE CAD model developed by Copenhagen Atomics. The CAD model was disassembled to keep the inlet plenum region only, which was subsequently cleaned and modified so that the mesh generated is under the memory limit. The results are merged to a few radial regions to show that the flow rate is highest in the central region. This would be useful for future improvement of the Griffin-SAM coupling model of the MSRE core. The last task investigated is tritium transport modeling using the standalone SAM code. This task aimed to initiate the effort to demonstrate and validate the tritium transport model implemented in SAM. The preliminary investigation employed an MSRE model consisting of the primary loop. Three tritium transport pathways were examined including the retention in the graphite, the permeation through the HX tube wall, and the removal from the off-gas system. The results compare well with the MSRE data, but improvements are still needed on the initial conditions (i.e., the present state may not have reached equilibrium), the boundary conditions, the off-gas system modeling, and a better numerical strategy to reach the equilibrium state.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Status of the framework for research in nuclear science and engineering - 25460

The Framework for Research in Nuclear Science and Engineering (FRENSIE) is a collection of packages written in C++ that are designed primarily to aid in methods development. New features are continually being added to the various packages and as a result, the Forward Adjoint Continuous Energy Monte Carlo (FACEMC) tool provided by FRENSIE continues to undergo verification and validation. While FRENSIE is not currently open source, the ultimate goal is for it to be released as such. A few of the more recent developments in FRENSIE include the addition of combinatorial geometry capabilities using ROOT, tet and hex meshing, support for thermal neutron S (α; β) data, photon Doppler broadening, electron interactions using basic analog electron physics models as well as an elastic moment-preserving model, and atomic relaxation. Preliminary verification results for much of the newly added physics models show good agreement between FACEMC and MCNP6. (authors)

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

A phase-field model for void and gas bubble superlattice formation in irradiated solids

A phase-field model to simulate the formation of both void and gas bubble superlattices is derived from a grand potential functional, assuming 1D diffusion of self-interstitial atoms. The model is capable of accounting for superlattice formation by either a nucleation and growth or spinodal decomposition mechanism; in this work, we focus on the nucleation and growth mechanism, using a discrete nucleation approach in the phase-field model. In simulations of void formation, short aligned rows of voids were initially formed, followed by growth in the size of the aligned rows, and finally leading to superlattice formation, consistent with experimental observations. Void superlattice spacing as a function of model parameters was quantified. Increased nucleation rates led to smaller superlattice spacing, while increased vacancy diffusivity led to larger superlattice spacing. In simulations of gas bubble superlattice formation, superlattice spacing decreased with increasing gas atom flux, consistent with experimental observations. Here, simulations with increasing ratio of gas atom flux to vacancy-interstitial pair production led to increased superlattice spacing, which is inconsistent with experimental observations at high gas atom flux rates; this discrepancy is attributed to the fact that the model does not account for bound gas atom-vacancy pairs that may dominate at high gas flux rates.

36 MATERIALS SCIENCE↗

Atomization data for spray combustion modeling

Computer models that simulate the energy release processes in spray combustion are highly dependent upon the quality of atomization data utilized. This paper presents results of analyses performed with a state-of-the-art rocket combustion code, demonstrating the important effects of initial droplet sizes and size distributions on combustion losses. Also, the questionable aspects and inapplicability of the generally available atomization data are discussed. One important and misunderstood aspect of the atomization process is the difference between spatial (concentration) and flux (temporal) droplet size distributions. These are addressed, and a computer model developed to assess this difference is described and results presented. Finally, experimental results are shown that demonstrate the often neglected effects of the local gas velocity field on the atomization process.

Ferrenberg, A. J.↗

Cross-Scale Catalyst Modeling Applied to H 2 Storage and Release via Formic Acid

Here, we propose the Systems-to-Atoms (S2A) modeling framework that integrates the kinetics of reaction chemistry and structural configurations across various length scales with the aim of establishing a versatile template for multiscale modeling of reactive flow problems and to predict the operando activity of catalyst materials. The approach encompasses a microkinetic model to analyze surface reactions on individual facets of catalyst nanoparticles coupled with the computation of average surface reaction rates for catalyst nanoparticles of specific size distributions. Macro-homogeneous surface reaction kinetics are derived as a function of catalyst loading and used as input parameters for the continuum-scale reactor model. The cross-scale framework enables the optimization of catalyst utilization through reactor design and operating strategy. To demonstrate the framework, we studied the storage and release of hydrogen from formic acid, a promising liquid organic hydrogen carrier (LOHC), over Pd, Pt, and Cu catalysts. The framework predicts observed trends in formic acid dehydrogenation activity for catalysts with comparable weight loadings and metal particle diameters, demonstrating satisfactory quantitative alignment. Finally, the seamless transmission of parameter uncertainties between scales is also discussed.

08 HYDROGEN↗

Feasibility of supersonic diode pumped alkali lasers: Model calculations

The feasibility of supersonic operation of diode pumped alkali lasers (DPALs) is studied for Cs and K atoms applying model calculations, based on a semi-analytical model previously used for studying static and subsonic flow DPALs. The operation of supersonic lasers is compared with that measured and modeled in subsonic lasers. The maximum power of supersonic Cs and K lasers is found to be higher than that of subsonic lasers with the same resonator and alkali density at the laser inlet by 25% and 70%, respectively. These results indicate that for scaling-up the power of DPALs, supersonic expansion should be considered.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Breakdown in helium in high-voltage open discharge with subnanosecond current front rise

Investigations of high-voltage open discharge in helium have shown a possibility of generation of current pulses with subnanosecond front rise, due to ultra-fast breakdown development. The open discharge is ignited between two planar cathodes with mesh anode in the middle between them. For gas pressure 6 Torr and 20 kV applied voltage, the rate of current rise reaches 500 A/(cm{sup 2} ns) for current density 200 A/cm{sup 2} and more. The time of breakdown development was measured for different helium pressures and a kinetic model of breakdown in open discharge is presented, based on elementary reactions for electrons, ions and fast atoms. The model also includes various cathode emission processes due to cathode bombardment by ions, fast atoms, electrons and photons of resonant radiation with Doppler shift of frequency. It is shown, that the dominating emission processes depend on the evolution of the discharge voltage during the breakdown. In the simulations, two cases of voltage behavior were considered: (i) the voltage is kept constant during the breakdown; (ii) the voltage is reduced with the growth of current. For the first case, the exponentially growing current is maintained due to photoemission by the resonant photons with Doppler-shifted frequency. For the second case, the dominating factor of current growth is the secondary electron emission. In both cases, the subnanosecond rise of discharge current was obtained. Also the effect of gas pressure on breakdown development was considered. It was found that for 20 Torr gas pressure the time of current rise decreases to 0.1 ns, which is in agreement with experimental data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗