Search NASA⌕ Search

SEARCH · Search NASA

Results for “BATTERY CELL MODELING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Lithium-Ion Batteries Being Evaluated for Low-Earth-Orbit Applications

The performance characteristics and long-term cycle life of aerospace lithium-ion (Li-ion) batteries in low-Earth-orbit applications are being investigated. A statistically designed test using Li-ion cells from various manufacturers began in September 2004 to study the effects of temperature, end-of-charge voltage, and depth-of-discharge operating conditions on the cycle life and performance of these cells. Performance degradation with cycling is being evaluated, and performance characteristics and failure modes are being modeled statistically. As technology improvements are incorporated into aerospace Li-ion cells, these new designs can be added to the test to evaluate the effect of the design changes on performance and life. Cells from Lithion and Saft have achieved over 2000 cycles under 10 different test condition combinations and are being evaluated. Cells from Mine Safety Appliances (MSA) and modules made up of commercial-off-the-shelf 18650 Li-ion cells connected in series/parallel combinations are scheduled to be added in the summer of 2005. The test conditions include temperatures of 10, 20, and 30 C, end-of-charge voltages of 3.85, 3.95, and 4.05 V, and depth-of-discharges from 20 to 40 percent. The low-Earth-orbit regime consists of a 55 min charge, at a constant-current rate that is 110 percent of the current required to fully recharge the cells in 55 min until the charge voltage limit is reached, and then at a constant voltage for the remaining charge time. Cells are discharged for 35 min at the current required for their particular depth-of-discharge condition. Cells are being evaluated in four-cell series strings with charge voltage limits being applied to individual cells by the use of charge-control units designed and produced at the NASA Glenn Research Center. These charge-control units clamp the individual cell voltages as each cell reaches its end-of-charge voltage limit, and they bypass the excess current from that cell, while allowing the full current flow to the remaining cells in the pack. The goal of this evaluation is to identify conditions and cell designs for Li-ion technology that can achieve more than 30,000 low-Earth-orbit cycles. Testing is being performed at the Naval Surface Warfare Center, Crane Division, in Crane, Indiana.

McKissock, Barbara I.↗

Highly textured metal anodes for stable aqueous batteries: Fabrication and characterization

We report a purely mechanical “cold-compression flow” method for fabricating Zn, Sn, and In substrates with tunable crystallographic textures. Using textured Zn as a model system, we investigate Zn electrocrystallization and demonstrate correlated growth of crystalline films with correlation lengths from tens to hundreds of micrometers. At 5 milliamperes per square centimeter (mA/cm 2 ), capacities between 20 and 82 milliampere hours per square centimeter (mA·hour/cm 2 ) are achieved depending on substrate texture level. At higher currents (40 mA/cm 2 ), capacities reach up to 604 mA·hour/cm 2 . Rotating disk electrode studies show that dominantly (002) textured Zn substrates exhibit enhanced corrosion resistance and reduced interphase passivation. We introduce an effective Damköhler number (Da*) to concisely describe morphological evolution during electrocrystallization across substrates with different textures. High-texture (002) Zn substrates substantially enhance performance in high-capacity (~20 mA·hour/cm 2 ) symmetric Zn||Zn cells and full cells (Zn||δ-MnO 2 and Zn||I 2 ), enabling fast-charging and prolonged energy storage in coin and pouch rechargeable Zn battery formats.

Science & Technology - Other Topics↗

Mass and charge transport relevant to the formation of toroidal lithium peroxide nanoparticles in an aprotic lithium-oxygen battery: An experimental and theoretical modeling study

In this paper, the discharge and charge mechanisms of rechargeable Li-O 2 batteries have been the subject of extensive investigation recently. However, they are not fully understood yet. Here we report a systematic study of the morphological transition of Li 2 O 2 from a single crystalline structure to a toroid like particle during the discharge-charge cycle, with the help of a theoretical model to explain the evolution of the Li 2 O 2 at different stages of this process. The model suggests that the transition starts in the first monolayer of Li 2 O 2 , and is subsequently followed by a transition from particle growth to film growth if the applied current exceeds the exchange current for the oxygen reduction reaction in a Li-O 2 cell. Furthermore, a sustainable mass transport of the diffusive active species (e.g., O 2 and Li + ) and evolution of the underlying interfaces are critical to dictate desirable oxygen reduction (discharge) and evolution (charge) reactions in the porous carbon electrode of a Li-O 2 cell.

25 ENERGY STORAGE↗

Representative volume element model of lithium-ion battery electrodes based on X-ray nano-tomography

For this, a new model that keeps all major advantages of the single-particle model of lithium-ion batteries (LIBs) and includes three-dimensional structure of the electrode was developed. Unlike the single spherical particle, this model considers a small volume element of an electrode, called the Representative Volume Element (RVE), which represent the real electrode structure. The advantages of using RVE as the model geometry was demonstrated for a typical LIB electrode consisting of nano-particle LiFePO 4 (LFP) active material. The three-dimensional morphology of the LFP electrode was reconstructed using a synchrotron X-ray nano-computed tomography at the Advanced Photon Source of the Argonne National. A 27 μm 3 cube from reconstructed structure was chosen as the RVE for the simulation purposes. The model was employed to predict the voltage curve in a half-cell during galvanostatic operations and validated with experimental data. The simulation results showed that the distribution of lithium inside the electrode microstructure is very different from the results obtained based on the single-particle model. The range of lithium concentration is found to be much greater, successfully illustrates the effect of microstructure heterogeneity.

25 ENERGY STORAGE↗

Modeling memoryless degradation under variable stress

Accelerated degradation tests can be used as the basis for predicting the performance or state of health of products and materials at use conditions over time. Measurements acquired at accelerated levels of stress are used to develop models that relate to the degradation of one or more performance measures. Frequently, products/materials of interest are subjected to variable stress levels during their lifetimes. However, testing is usually performed only at a few fixed stress levels. In such cases, cumulative degradation models are developed and assessed by using data acquired under those fixed stress conditions. The degradation rate at any stress condition within the range of the model can be estimated by the derivative of the cumulative model at that stress condition. It follows that, to predict cumulative degradation over variable use conditions, one might integrate the fluctuating degradation rate over time. Existing approaches for doing this consider degradation rates that depend only on the current stress level. Here, we propose to allow the degradation rate to also depend on the current state of health as indicated by the associated performance measure(s). The resulting modeling approach is capable of portraying a broader range of degradation behavior than existing approaches. The assertion of memoryless degradation by using this or any other approach should be assessed experimentally with data acquired under variable stress in order to increase confidence that the integrated rate model is accurate. In this article, we demonstrate the additional capability of the proposed approach by developing empirical memoryless rate-based degradation models to predict resistance increase and capacity decrease in lithium-ion cells that are being evaluated for use in electric vehicles. Here, we then assess the plausibility of these models.

42 ENGINEERING↗

General microscopic model of magnetoelastic coupling from first principles

Magnetoelastic coupling, i.e., the change of crystal lattice induced by a spin order, is not only scientifically interesting, but also technically important. In this work, we propose a general microscopic model from firstprinciples calculations to describe the magnetoelastic coupling and provide a way to construct the microscopic model from density functional theory calculations. Based on this model, we reveal that there exists a previously unexpected contribution to the electric polarization induced by the spin order in multiferroics due to the combined effects of magnetoelastic coupling and piezoelectric effect. Interestingly and surprisingly, we find that this latticedeformation contribution to the polarization is even larger than that from the pure electronic and ion-displacement contributions in BiFeO 3 . We conclude this model of magnetoelastic coupling can be generally applied to investigate the other magnetoelastic phenomena.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

X-ray absorption of liquid water by advanced ab initio methods

In this work, oxygen K-edge x-ray absorption spectra of liquid water are computed based on configurations from advanced ab initio molecular dynamics simulations, as well as an electron excitation theory from the GW method. One the one hand, the molecular structures of liquid water are accurately predicted by including both van der Waals interactions and a hybrid functional (PBE0). On the other hand, the dynamic screening effects on electron excitation are approximately described by the recently developed enhanced static Coulomb-hole and screened-exchange approximation of W. Kang and M. S. Hybertsen. The resulting spectra of liquid water are in better quantitative agreement with the experimental spectra due to the softened hydrogen bonds and the slightly broadened spectra originating from the better screening model.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A novel PEMEC with 3D printed non-conductive bipolar plate for low-cost hydrogen production from water electrolysis

For establishing the large-scale hydrogen production as energy carrier from water electrolysis, improving cost-effectiveness and efficiency remains the main challenges. In this study, we propose a novel proton exchange membrane electrolyzer cell (PEMEC), consisting of non-conductive bipolar plates (BPs) and thin film liquid/gas diffusion layers (TF-LGDLs) to reduce the cost and improve the PEMEC performance. The 3D printed non-conductive BP is manufactured with low-cost polylactic acid (PLA) and is mainly functioned to distribute the water and gas products. A titanium thin film LGDL (TF-LGDL) with surroundings is developed for directly transporting electrons from the external power sources, which changes the electron transport path in the PEMECs. The PLA BP exhibits an extremely low cost (1/10 of that of the graphite BP), and the hydrogen production rate per unit BP cost in a PEMEC with PLA BP, is almost 6 times higher than a conventional one with graphite BPs. More importantly, the PEMECs with PLA BPs can achieve a good electrochemical performance of 2.21 V at 1 A/cm 2 under room temperature. A model is also developed to investigate the impact of the BP resistivity of on the cell performance, and a guideline for the selection guideline of conductivity of BPs material is provided. The easily accessible and low-cost PLA BPs coupled with the new electron-conducting path will drive the exploration of plastic materials for economic and efficient water splitting or other energy conversion devices, including fuel cells, batteries, and solar cells.

09 BIOMASS FUELS↗

Method for monitoring/managing electrochemical energy device by detecting intercalation stage changes

A method for determining an operating state (e.g., state-of-charge or state-of-health) and/or generating management (charge/discharge) control information in a system including an electrochemical energy device (EED, e.g., a rechargeable Li-ion battery, supercapacitor or fuel cell) that uses optical sensors to detect the intercalation stage change events occurring in the EED. The externally or internally mounted optical sensors measure operating parameter (e.g., strain and/or temperature) changes of the EED during charge/recharge cycling, and transmit measured parameter data using light signals sent over optical fibers to a detector/converter. A processor then analyzes the measured parameter data, e.g., using a model-based estimation process, to detect intercalation stage changes (i.e., crystalline structure changes caused by migration of guest species, such as Li-ions, between the EED's anode and cathode), and generates the operating state and charge/discharge control information based the analysis.

25 ENERGY STORAGE↗

Manufacturing of Fabric Electrodes using a High-Throughput Screening Platform for Redox Flow Batteries

The objective of this project is to establish a new manufacturing methodology with machine learning- based high-throughput screening for the design and development of hierarchical structured, high-performance fabric electrodes for redox flow batteries (RFBs). The end goal of the project is to design and manufacture fabric electrodes for RFB applications that can provide 250 mA/cm2 current density operation for 100-cycles with 80% average energy efficiency. This was accomplished by first examining the structure-performance-property linkages of the electrodes provided by our partner, AvCarb. The electrodes’ microstructure was characterized by determining their pore size distribution, tortuosity, specific surface area, and porosity. The ohmic, charge transfer and mass transfer resistances were then calculated using electrochemical impedance spectroscopy. Carbon cloth electrodes showed the greatest resistance, which was dominated by charge transfer resistance, which we believe is related to the surface functionalization. Full cell cycling was used in order to determine the area specific resistance and energy efficiency of the cells. All of this experimental data and the results of the mathematical model (to increase the amount of inputs with parametric sweeping) were used to develop a machine learning-based model for the design of high-performance fabric electrodes. Using the results from the machine learning tool, optimized electrodes were fabricated by AvCarb. The ohmic, charge transfer and mass transfer resistances for these new electrodes were measured, and both performed better than any of the initial samples which had been provided by AvCarb.

25 ENERGY STORAGE↗

Alumina – Stabilized SEI and CEI in Potassium Metal Batteries

Aluminum oxide (Al 2 O 3 ) nanopowder is spin-coated onto both sides of commercial polypropene separator to create artificial solid-electrolyte interphase (SEI) and artificial cathode electrolyte interface (CEI) in potassium metal batteries (KMBs). Here, this significantly enhances the stability, including of KMBs with Prussian Blue (PB) cathodes. For example, symmetric cells are stable after 1,000 cycles at 0.5 mA/cm 2 –0.5 mAh/cm 2 and 3.0 mA/cm 2 –0.5 mAh/cm 2 . Alumina modified separators promote electrolyte wetting and increase ionic conductivity (0.59 vs. 0.2 mS/cm) and transference number (0.81 vs. 0.23). Cryo-stage focused ion beam (cryo-FIB) analysis of cycled modified anode demonstrates dense and planar electrodeposits, versus unmodified baseline consisting of metal filaments (dendrites) interspersed with pores and SEI. Alumina-modified CEI also suppresses elemental Fe crossover and reduces cathode cracking. Mesoscale modeling of metal – SEI interactions captures crucial role of intrinsic heterogeneities, illustrating how artificial SEI affects reaction current distribution, conductivity and morphological stability.

25 ENERGY STORAGE↗

Next Generation Batteries for Electric Aviation and Space

Energy storage plays a critical part in the success of future NASA missions that desire batteries with higher energy density, higher power, and most critically improved safety. These performance requirements stretch beyond that of electric automobile markets and are required for enabling widespread adoption of electric aviation. One approach to improve the safety and energy is the transition to non-volatile solid-state electrolytes (SSE) which promise many advantages over traditional flammable liquid electrolytes and may also be an enabling technology for next generation chemistries such as lithium-sulfur (Li-S). However, significant manufacturing challenges must be overcome before the adoption of such technology. This study will discuss the development of solid electrolytes specifically designed to meet future NASA electric aviation targets with densified thicknesses between 20-30 microns derived using solvent processing techniques. Films were produced 10-15 times thinner than comparable bulk cold pressed powder electrolytes and achieved thicknesses comparable to commercial polyolefin separators (25 micron) used in commercial liquid containing lithium-ion cells. Furthermore, design and development of novel cathode composites through integration of experiment and a particle dynamics model will be discussed. Beyond aeronautics, unique challenges and requirements exist for energy storage for space applications, which can cover extreme temperatures and material scarcity for in-situ derived materials. Additionally, this talk will briefly cover the need and development of lunar and Martian derived electrode materials for in-situ manufacturing of energy storage devices.

Batteries↗

Optimization of Component Sizing for a Fuel Cell-Powered Truck to Minimize Ownership Cost

In this study, we consider fuel cell-powered electric trucks (FCETs) as an alternative to conventional medium- and heavy-duty vehicles. FCETs use a battery combined with onboard hydrogen storage for energy storage. The additional battery provides regenerative braking and better fuel economy, but it will also increase the initial cost of the vehicle. Heavier reliance on stored hydrogen might be cheaper initially, but operational costs will be higher because hydrogen is more expensive than electricity. Achieving the right tradeoff between these power and energy choices is necessary to reduce the ownership cost of the vehicle. This paper develops an optimum component sizing algorithm for FCETs. The truck vehicle model was developed in Autonomie, a platform for modelling vehicle energy consumption and performance. The algorithm optimizes component sizes to minimize overall ownership cost, while ensuring that the FCET matches or exceeds the performance and cargo capacity of a conventional vehicle. Class 4 delivery truck and class 8 linehaul trucks are shown as examples. We estimate the ownership cost for various hydrogen costs, powertrain components, ownership periods, and annual vehicle miles travelled.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Understanding the Influence of Li 7 La 3 Zr 2 O 12 Nanofibers on Critical Current Density and Coulombic Efficiency in Composite Polymer Electrolytes

Composite polymer electrolytes (CPEs)are attractive materials for solid-state lithium metal batteries, owing to their high ionic conductivity from ceramic ionic conductors and flexibility from polymer components. As with all lithium metal batteries, however, CPEs face the challenge of dendrite formation and propagation. Not only does this lower the critical current density (CCD) before cell shorting, but the uncontrolled growth of lithium deposits may limit Coulombic efficiency (CE) by creating dead lithium. Here, we present a fundamental study on how the ceramic components of CPEs influence these characteristics. CPE membranes based on poly-(ethylene oxide) and lithium bis-(trifluoro methane sulfonyl)-imide(PEO-LiTFSI) with Li 7 La 3 Zr 2 O 12 (LLZO) nanofibers were fabricated with industrially relevant roll-to-roll manufacturing techniques. Galvanostatic cycling with lithium symmetric cells shows that the CCD can be tripled by including 50 wt % LLZO, but half-cell cycling reveals that this comes at the cost of CE. Varying the LLZO loading shows that even a small amount of LLZO drastically lowers the CE, from 88% at 0 wt % LLZO to 77% at just 2 wt % LLZO. Mesoscale modeling reveals that the increase in CCD cannot be explained by an increase in the macroscopic or microscopic stiffness of the electrolyte; only the microstructure of the LLZO nanofibers in the PEO-LiTFSI matrix slows dendrite growth by presenting physical barriers that the dendrites must push or grow around. This tortuous lithium growth mechanism around the LLZO is corroborated with mass spectrometry imaging. In conclusion, this work highlights important elements to consider in the design of CPEs for high-efficiency lithium metal batteries.

36 MATERIALS SCIENCE↗

Accelerated Short Circuiting in Anode-Free Solid-State Batteries Driven by Local Lithium Depletion

“Anode-free” solid-state batteries (SSBs), which have no anode active material, can exhibit extremely high energy density (≈1500 Wh L -1 ). However, there is a lack of understanding of the lithium plating/stripping mechanisms at initially lithium-free solid-state electrolyte (SSE) interfaces because excess lithium metal is often used. Here, it is demonstrated that commercially relevant quantities of lithium (>5 mAh cm -2 ) can be reliably plated at moderate current densities (1 mA cm -2 ) using the sulfide SSE Li 6 PS 5 Cl. Investigations of lithium plating/stripping mechanisms, in conjunction with cryo-ocused ion beam (FIB) imaging, synchrotron tomography, and phase-field modeling, reveal that the cycling stability of these cells is fundamentally limited by the nonuniform presence of lithium during stripping. Local lithium depletion causes isolated lithium regions toward the end of stripping, decreasing electrochemically active area and resulting in high local current densities and void formation. This accelerates subsequent filament growth and short circuiting compared to lithium-excess cells. Despite this degradation mode, here it is shown that anode-free cells exhibit comparable Coulombic efficiency to lithium-excess cells, and improved resistance to short circuiting is achieved by avoiding local lithium depletion through retention of thicker lithium at the interface. These new insights provide a foundation for engineering future high-energy anode-free SSBs.

25 ENERGY STORAGE↗

Electrified Operando -Freezing of Electrocatalytic CO 2 Reduction Cells for Cryogenic Electron Microscopy

The ability to freeze and stabilize reaction intermediates in their metastable states and obtain their structural and chemical information with high spatial resolution would be very powerful to unravel the fundamentals in many important materials technologies such as catalysis and batteries. Here, we develop an electrified operando-freezing methodology for the first time to preserve these metastable states under electrochemical reaction conditions for cryogenic electron microscopy (cryo-EM) imaging and spectroscopy. Using Cu catalysts for CO 2 reduction as a model system, we observe restructuring of the Cu catalyst in a CO 2 atmosphere while the same catalyst remains intact in an air atmosphere at the nanometer scale. Furthermore, we discover the existence of single valance Cu (1+) state and C-O bonding at the electrified liquid-solid interface of the operando-frozen samples, which are key reaction intermediates that traditional ex situ measurements fail to detect. Finally, this work highlights our novel technique to study the local structure and chemistry of electrified liquid-solid interfaces, which has broad impact for many electrochemical reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Phase-Field Modeling of Materials Interfaces and Nanostructures

Nanostructured materials offer unique properties for a wide range of energy applications. Among various known processing methods, liquid metal dealloying (LMD)—the selective dissolution of a base alloy element into a metallic melt—has emerged as a powerful technique to produce a new class of nano-/meso-scale open porous and bicontinuous composite structures with ultra-high interfacial area. LMD has recently been complemented by the advent of vapor phase dealloying (VPD), a novel technique that exploits the selective evaporation of one element from a parent alloy containing elements with very different vapor pressures, thereby enabling to fabricate open nanoporous structures of various elements from less-noble metals to inorganic elements regardless of their chemical activity without requiring high LMD temperatures and chemical etching. Together LMD and VPD have greatly expanded the scope of dealloying techniques, limited by traditional electrochemical means to noble metals, and boosted the design of new functional and structural materials that combine a wide variety of elements. Topologically-connected open porous structures with ultra-high surface area allow mass transport within the structure while preserving structural integrity, enabling them to serve as catalysts, fuel cells, supercapacitors, or high-capacity battery materials. Bicontinuous composite structures in turn can display high strength and high ductility or superior radiation-damage resistance due to the ultra-high interface area between interpenetrating solid phases. This research program makes use of state-of-the-art computational methods to understand at a basic level the self-organizing dealloying process with main focus on dealloying kinetics and interfacial pattern formation at the dealloying front controlling initial structure size, topology, and phase compositions. Phase-field simulation studies of LMD focus on solid solutions, line compounds, and intermetallic systems that can form ternary composites by nucleation and growth of a new phase. Studies of VPD employ phase-field modeling and a hybrid method combining a kinetic Monte Carlo (KMC) model of evaporation and surface diffusion with molecular dynamics for vapor-phase transport inside nanopores. Simulations explore mechanisms of interface- and diffusion-controlled dealloying kinetics, both observed in VPD but not fundamentally understood. In addition, our newly developed multi-physics phase-field approach of large-volume-change phase transformations is being used to model novel 3D anode geometries based on dealloyed nanoporous structures including novel sandwiched graphene/Si/silica for highrate Li ion battery. Those studies are aimed at elucidating geometric design principles that improve mechanical stability. We expect this research to enhance the capability to tailor nano-/mesoscale structures for a wide range of energy-related materials applications and to yield further advances in computational methodologies that benefit a broad materials research community.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Li Metal Anodes and Rechargeable Lithium Metal Batteries. Springer Series in Materials Science

Lithium (Li) metal is an ideal anode material for rechargeable batteries. With the urgent need for the “next generation” rechargeable batteries, such as Li-S, Li-air batteries as well as rechargeable Li metal batteries using Li intercalation compounds as the cathode, the use of Li metal anode has attracted significant interests in recent years. Unfortunately, rechargeable batteries based on Li metal anode have not yet been commercialized mainly due to two barriers: one is the growth of Li dendrites and associated safety hazard, and another is the low Coulombic efficiency (CE) of Li cycling and associated early battery failure due to Li powdering and increasing cell impedance. To have a high CE, minimum side reactions between freshly/native deposited Li and electrolyte has to be minimized. These reactions are proportional to the chemical and electrochemical activity of native Li when they are in direct contact with surrounding electrolyte. They are also proportional to the surface area of deposited Li. This means that high CE of Li deposition/stripping always related to a low surface area Li deposition and suppressed Li dendrite growth. Therefore, the enhancement of CE is a more fundamental factors controlling long term, stable cycling of Li metal anode. In this book, we will first review the general models of the dendrite growth mechanism. The effect of SEI layer on the modeling of Li dendrite growth will also be discussed. Then we will discuss various instruments/tools that are critical for the investigation of Li dendrite growth. In the Chapter 3, various factors which affect CE of Li cycling and dendrite growth will be discussed together with an emphasize on enhancement of CE. Chapter 4 of the book will discuss the specific application of Li metal anode in several key rechargeable Li metal batteries, including Li-air batteries, Li-S batteries and Li metal batteries using intercalation compounds as cathode. At last, the perspective on the future development and application of Li metal batteries will be discussed in the Chapter 5.

anode↗