SEARCH · Search NASA

Results for “Behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

All sources NASA NTRS DOE OSTI

NASA NTRS1994

(abstract) Line Mixing Behavior of Hydrogen-Broadened Ammonia Under Jovian Atmospheric Conditions

Laboratory spectral data reported last year have been used to investigate the line mixing behavior of hydrogen-broadened ammonia inversion lines. The data show that broadening parameters appearing in the modified Ben-Reuven opacity formalism of Berge and Gulkis (1976) cannot maintain constant values over pressure ranges that include low to moderate pressures and high pressures. Also, they cannot change drastically in value, as in the Spilker (1990) revision of the Berge and Gulkis formalism. It has long been recognized that at low pressures, less than about 1 bar of a Jovian atmospheric mixture, a VVW formalism yields more accurate predictions of ammonia opacity than Ben-Reuven formalisms. At higher pressures the Ben-Reuven formalisms are more accurate. Since the Ben-Reuven lineshape collapses to a VVW lineshape in the low pressure limit, this low pressure inaccuracy of the Ben-Reuven formalisms is surprising. By incorporating various behavior, a new formalism is produced that is more accurate than previous formalisms, particularly in the critical 'transition region' from 0.5 to 2 bars, and that can be used without discontinuity from pressures of zero to hundreds of bars. The new formalism will be useful in such applications as interpretation of radio astronomical and radio occultation data on giant planet atmospheres, and radiative transfer modeling of those atmospheres.

inversion lines formalisms radiative transfer mode↗

NASA NTRS2007

Effects of Rhenium Addition on the Temporal Evolution of the Nanostructure and Chemistry of a Model Ni-Cr-Al Superalloy: Analysis of the Coarsening Behavior - 2

The temporal evolution of the nanostructure and chemistry of a model Ni-8.5 at.% Cr-10 at.% Al alloy with the addition of 2 at.% Re was studied using transmission electron microscopy and atom-probe tomography in order to measure the number density and mean radius of the y' (LIZ) precipitates and the chemistry of the y'-precipitates and the y (fcc)-matrix. In this article, the coarsening behavior of the y'-precipitates is discussed in detail and compared with the Umantsev-Olson model for multi-component alloys. In addition, the experimental results are evaluated with PrecipiCalc(TradeMark) simulations. The results show that the diffusivities of the solute elements play a major role in the coarsening behavior of the y'-precipitates and that the addition of Re retards the coarsening kinetics and stabilizes the spheroidal morphology of the precipitates by reducing the interfacial energy.

Yoon, Kevin E.↗

NASA NTRS2007

Effect of an Opaque Reflecting Layer on the Thermal Behavior of a Thermal Barrier Coating

A parametric study using a two-flux approximation of the radiative transfer equation was performed to examine the effects of an opaque reflective layer on the thermal behavior of a typical semitransparent thermal barrier coating on an opaque substrate. Some ceramic materials are semitransparent in the wavelength ranges where thermal radiation is important. Even with an opaque layer on each side of the semitransparent thermal barrier coating, scattering and absorption can have an effect on the heat transfer. In this work, a thermal barrier coating that is semitransparent up to a wavelength of 5 micrometers is considered. Above 5 micrometers wavelength, the thermal barrier coating is opaque. The absorption and scattering coefficient of the thermal barrier was varied. The thermal behavior of the thermal barrier coating with an opaque reflective layer is compared to a thermal barrier coating without the reflective layer. For a thicker thermal barrier coating with lower convective loading, which would be typical of a combustor liner, a reflective layer can significantly decrease the temperature in the thermal barrier coating and substrate if the scattering is weak or moderate and for strong scattering if the absorption is large. The layer without the reflective coating can be about as effective as the layer with the reflective coating if the absorption is small and the scattering strong. For low absorption, some temperatures in the thermal barrier coating system can be slightly higher with the reflective layer. For a thin thermal barrier coating with high convective loading, which would be typical of a blade or vane that sees the hot sections of the combustor, the reflective layer is not as effective. The reflective layer reduces the surface temperature of the reflective layer for all conditions considered. For weak and moderate scattering, the temperature of the TBC-substrate interface is reduced but for strong scattering, the temperature of the substrate is increased slightly.

Spuckler, Charles M.↗

NASA NTRS2005

Loggers and Forest Fragmentation: Behavioral Models of Road Building in the Amazon Basin

Although a large literature now exists on the drivers of tropical deforestation, less is known about its spatial manifestation. This is a critical shortcoming in our knowledge base since the spatial pattern of land-cover change and forest fragmentation, in particular, strongly affect biodiversity. The purpose of this article is to consider emergent patterns of road networks, the initial proximate cause of fragmentation in tropical forest frontiers. Specifically, we address the road-building processes of loggers who are very active in the Amazon landscape. To this end, we develop an explanation of road expansions, using a positive approach combining a theoretical model of economic behavior with geographic information systems (GIs) software in order to mimic the spatial decisions of road builders. We simulate two types of road extensions commonly found in the Amazon basin in a region: showing the fishbone pattern of fragmentation. Although our simulation results are only partially successful, they call attention to the role of multiple agents in the landscape, the importance of legal and institutional constraints on economic behavior, and the power of GIs as a research tool.

Arima, Eugenio Y.↗

NASA NTRS2007

A Review of Training Methods and Instructional Techniques: Implications for Behavioral Skills Training in U.S. Astronauts (DRAFT)

Long-duration space missions (LDM) place unique physical, environmental and psychological demands on crewmembers that directly affect their ability to live and work in space. A growing body of research on crews working for extended periods in isolated, confined environments reveals the existence of psychological and performance problems in varying degrees of magnitude. The research has also demonstrated that although the environment plays a cathartic role, many of these problems are due to interpersonal frictions (Wood, Lugg, Hysong, & Harm, 1999), and affect each individual differently. Consequently, crewmembers often turn to maladaptive behaviors as coping mechanisms, resulting in decreased productivity and psychological discomfort. From this body of research, critical skills have been identified that can help a crewmember better navigate the psychological challenges of long duration space flight. Although most people lack several of these skills, most of them can be learned; thus, a training program can be designed to teach crewmembers effective leadership, teamwork, and self-care strategies that will help minimize the emergence of maladaptive behaviors. Thus, it is the purpose of this report is twofold: 1) To review the training literature to help determine the optimal instructional methods to use in delivering psychological skill training to the U.S. Astronaut Expedition Corps, and 2) To detail the structure and content of the proposed Astronaut Expedition Corps Psychological Training Program.

Hysong, Sylvia J.↗

NASA NTRS2005

New Integrated Modeling Capabilities: MIDAS' Recent Behavioral Enhancements

The Man-machine Integration Design and Analysis System (MIDAS) is an integrated human performance modeling software tool that is based on mechanisms that underlie and cause human behavior. A PC-Windows version of MIDAS has been created that integrates the anthropometric character "Jack (TM)" with MIDAS' validated perceptual and attention mechanisms. MIDAS now models multiple simulated humans engaging in goal-related behaviors. New capabilities include the ability to predict situations in which errors and/or performance decrements are likely due to a variety of factors including concurrent workload and performance influencing factors (PIFs). This paper describes a new model that predicts the effects of microgravity on a mission specialist's performance, and its first application to simulating the task of conducting a Life Sciences experiment in space according to a sequential or parallel schedule of performance.

Gore, Brian F.↗

NASA NTRS2007

Human Activity Behavior and Gesture Generation in Virtual Worlds for Long- Duration Space Missions

A virtual worlds presentation technique with embodied, intelligent agents is being developed as an instructional medium suitable to present in situ training on long term space flight. The system combines a behavioral element based on finite state automata, a behavior based reactive architecture also described as subsumption architecture, and a belief-desire-intention agent structure. These three features are being integrated to describe a Brahms virtual environment model of extravehicular crew activity which could become a basis for procedure training during extended space flight.

Sierhuis, Maarten↗

NASA NTRS2008

Behavioral and Psychological Issues in Long Duration Head-down Bed Rest

Behavioral health services, similar to those offered to the U.S. astronauts who complete six-month missions on board the International Space Station, were provided to 13 long-duration head-down bed rest participants. Issues in psychological screening, selection, and support are discussed as they relate to other isolated and confined environments. Psychological services offered to participants are described, and challenges in subject selection and retention are discussed. Psychological support and training provided to both subjects and study personnel have successfully improved the well-being of study participants. Behavioral health services are indispensable to long-duration head-down tilt bed rest studies.

Seaton, Kimberly A.↗

NASA NTRS2008

Fatigue Behavior of a Third Generation PM Disk Superalloy

The fatigue behavior of a 3rd generation PM disk alloy, LSHR, was studied at 1300 F. Tensile, creep, and fatigue tests were run on smooth and notched (Kt = 2) bars under a variety of conditions. Analysis of smooth bar fatigue data, run under strain and load control with R ratios of 0 and -1, showed that a stress based Smith-Watson-Topper approach could collapse the data set. While the tensile and creep data showed substantial notch strengthening at 1300 F, the fatigue data showed a life deficit for the notch specimens. A viscoplastic finite element model, which accounted for stress relaxation at the notch tip, provided the best correlation between the notched and smooth bar behavior, although the fatigue data was not fully rationalized based on this simplified viscoplastic model of the stresses at the notch tip.Inclusion of a 90 sec dwell at peak load was found to dramatically decrease notch fatigue life. This result was shown to be consistent with a simple linear creep-fatigue damage rule, where creep damage dominated at low stresses and fatigue damage was more prevalent at higher stresses.

Gayda, John↗

NASA NTRS2001

Calculation of the Aerodynamic Behavior of the Tilt Rotor Aeroacoustic Model (TRAM) in the DNW

Comparisons of measured and calculated aerodynamic behavior of a tiltrotor model are presented. The test of the Tilt Rotor Aeroacoustic Model (TRAM) with a single, 1/4-scale V- 22 rotor in the German-Dutch Wind Tunnel (DNW) provides an extensive set of aeroacoustic, performance, and structural loads data. The calculations were performed using the rotorcraft comprehensive analysis CAMRAD II. Presented are comparisons of measured and calculated performance and airloads for helicopter mode operation, as well as calculated induced and profile power. An aerodynamic and wake model and calculation procedure that reflects the unique geometry and phenomena of tiltrotors has been developed. There are major differences between this model and the corresponding aerodynamic and wake model that has been established for helicopter rotors. In general, good correlation between measured and calculated performance and airloads behavior has been shown. Two aspects of the analysis that clearly need improvement are the stall delay model and the trailed vortex formation model.

Johnson, Wayne↗

NASA NTRS2009

The Effect of Impingement on Transitional Behavior in Underexpanded Jets

An investigation into the development of flow unsteadiness in impinging axisymmetric underexpanded jets has been conducted at NASA Langley Research Center. The study has examined the effect of an impingement target placed at various distances and angles on transitional behavior of such jets. Two nozzles, with exit Mach numbers of 1.0 and 2.6, were used in this investigation. Planar laser-induced fluorescence of nitric oxide (NO PLIF) has been used to identify flow unsteadiness and to image transitional and turbulent flow features. Measurements of the location of the onset of various degrees of unsteady flow behavior have been made using these PLIF images. Both qualitative and quantitative comparisons are presented to demonstrate the observed effects of impingement and flow parameters on the process of the transition to turbulence. The presence of the impingement target was found to significantly shorten the distance to transition to turbulence by up to a factor of approximately three, with closer targets resulting in slightly shorter distance to transition and turbulence. The location at which the flow first exhibits unsteadiness was found to have a strong dependence on the presence and location of key flow structures. This paper presents quantitative results on transition criteria for free and impinging jets.

Inman, Jennifer A.↗

NASA NTRS2009

Timing Behavior of the Magnetically Active Rotation-Powered Pulsar in the Supernova Remnant Kesteven 75

We report a large spin-up glitch in PSR J1846-0258 which coincided with the onset of magnetar-like behavior on 2006 May 31. We show that the pulsar experienced an unusually large glitch recovery, with a recovery fraction of Q = 5.9+/-0.3, resulting in a net decrease of the pulse frequency. Such a glitch recovery has never before been observed in a rotation-powered pulsar, however, similar but smaller glitch over-recovery has been recently reported in the magnetar AXP 4U 0142+61 and may have occurred in the SGR 1900+14. We discuss the implications of the unusual timing behavior in PSR J1846-0258 on its status as the first identified magnetically active rotation-powered pulsar.

Livingstone, Margaret A.↗

NASA NTRS2010

Probabilistic Multi-Factor Interaction Model for Complex Material Behavior

Complex material behavior is represented by a single equation of product form to account for interaction among the various factors. The factors are selected by the physics of the problem and the environment that the model is to represent. For example, different factors will be required for each to represent temperature, moisture, erosion, corrosion, etc. It is important that the equation represent the physics of the behavior in its entirety accurately. The Multi-Factor Interaction Model (MFIM) is used to evaluate the divot weight (foam weight ejected) from the external launch tanks. The multi-factor has sufficient degrees of freedom to evaluate a large number of factors that may contribute to the divot ejection. It also accommodates all interactions by its product form. Each factor has an exponent that satisfies only two points - the initial and final points. The exponent describes a monotonic path from the initial condition to the final. The exponent values are selected so that the described path makes sense in the absence of experimental data. In the present investigation, the data used were obtained by testing simulated specimens in launching conditions. Results show that the MFIM is an effective method of describing the divot weight ejected under the conditions investigated. The problem lies in how to represent the divot weight with a single equation. A unique solution to this problem is a multi-factor equation of product form. Each factor is of the following form (1 xi/xf)ei, where xi is the initial value, usually at ambient conditions, xf the final value, and ei the exponent that makes the curve represented unimodal that meets the initial and final values. The exponents are either evaluated by test data or by technical judgment. A minor disadvantage may be the selection of exponents in the absence of any empirical data. This form has been used successfully in describing the foam ejected in simulated space environmental conditions. Seven factors were required to represent the ejected foam. The exponents were evaluated by least squares method from experimental data. The equation is used and it can represent multiple factors in other problems as well; for example, evaluation of fatigue life, creep life, fracture toughness, and structural fracture, as well as optimization functions. The software is rather simplistic. Required inputs are initial value, final value, and an exponent for each factor. The number of factors is open-ended. The value is updated as each factor is evaluated. If a factor goes to zero, the previous value is used in the evaluation.

Abumeri, Galib H.↗

NASA NTRS2010

Explanation of Anomalous Behavior Observed in Impedance Eduction Techniques Using Measured Data

Several enhancements that improve the accuracy and robustness of an impedance eduction technique that use an automatic optimizer are presented. These enhancements are then used to launch an intensive investigation into the cause of anomalous behavior that occurs for a small number of test conditions. This anomalous behavior is investigated for both a hardwall insert and a conventional liner. The primary conclusions of the study are that: (1) for the hard wall insert, the anomalies are due to narrow peaks in the objective function, (2) For the conventional liner, the anomalies are due to the presence of an extremely flat objective function, and (3) the anomalies appear to be triggered by inconsistencies between the duct propagation model and the measured data. At high frequencies, the duct propagation model may need to include the effects of higher-order duct modes, whereas at low frequencies, the effects of the mean boundary layer may have to be included.

Watson, Willie R.↗

NASA NTRS2010

Experimental Charging Behavior of Orion UltraFlex Array Designs

The present ground based investigations give the first definitive look describing the charging behavior of Orion UltraFlex arrays in both the Low Earth Orbital (LEO) and geosynchronous (GEO) environments. Note the LEO charging environment also applies to the International Space Station (ISS). The GEO charging environment includes the bounding case for all lunar mission environments. The UltraFlex photovoltaic array technology is targeted to become the sole power system for life support and on-orbit power for the manned Orion Crew Exploration Vehicle (CEV). The purpose of the experimental tests is to gain an understanding of the complex charging behavior to answer some of the basic performance and survivability issues to ascertain if a single UltraFlex array design will be able to cope with the projected worst case LEO and GEO charging environments. Stage 1 LEO plasma testing revealed that all four arrays successfully passed arc threshold bias tests down to -240 V. Stage 2 GEO electron gun charging tests revealed that only the front side area of indium tin oxide coated array designs successfully passed the arc frequency tests

Golofaro, Joel T.↗

NASA NTRS2010

NASA Human Research Program Behavioral Health and Performance Element (BHP)

The goal of NASA BHP is to identify, characterize, and prevent or reduce behavioral health and performance risks associated with space travel, exploration, and return to terrestrial life. The NASA Behavioral Health and Performance Operations Group (BHP Ops) supports astronauts and their families before, during, and after a long-duration mission (LDM) on the ISS. BHP Ops provides ISS crews with services such as preflight training (e.g., psychological factors of LDM, psychological support, cross-cultural); preflight, in-flight, and postflight support services, including counseling for astronauts and their families; and psychological support such as regular care packages and a voice-over IP phone system between crew members and their families to facilitate real-time one-on-one communication.

Whitmire, Sandra↗

NASA NTRS2009

Spectral Invariant Behavior of Zenith Radiance Around Cloud Edges Observed by ARM SWS

The ARM Shortwave Spectrometer (SWS) measures zenith radiance at 418 wavelengths between 350 and 2170 nm. Because of its 1-sec sampling resolution, the SWS provides a unique capability to study the transition zone between cloudy and clear sky areas. A spectral invariant behavior is found between ratios of zenith radiance spectra during the transition from cloudy to cloud-free. This behavior suggests that the spectral signature of the transition zone is a linear mixture between the two extremes (definitely cloudy and definitely clear). The weighting function of the linear mixture is a wavelength-independent characteristic of the transition zone. It is shown that the transition zone spectrum is fully determined by this function and zenith radiance spectra of clear and cloudy regions. An important result of these discoveries is that high temporal resolution radiance measurements in the clear-to-cloud transition zone can be well approximated by lower temporal resolution measurements plus linear interpolation.

Marshak, A.↗

NASA NTRS2010

NASA Astronaut Selection 2009: Behavioral Overview

NASA's multi-phase U.S. astronaut selection process seeks to identify the most qualified astronaut candidates from a large number of applicants. With the approaching retirement of the Space Shuttle, NASA focused on selecting those individuals who were most suited to the unique demands of long-duration spaceflight. In total, NASA received 3,535 applications for the 2009 astronaut selection cycle. Of these, 123 were invited to NASA Johnson Space Center (JSC) for Round 1 initial screening and interviews, which consisted of an Astronaut Selection Board (ASB) preliminary interview, medical review, and psychological testing. Of these, 48 individuals were invited to return for Round 2. This round consisted of medical testing, further behavioral assessments, and a second ASB interview. Following this, nine astronaut candidates (ASCANs) were ultimately chosen to go forward to basic training. The contents, benefits, and lessons learned from implementing this phased process will be discussed. The lessons learned can benefit the future selection of space flyers, whether they are NASA or commercial. Learning Objective: 1) Familiarization with the 2009 NASA behavioral screening process for astronaut applicants.

Holland, A. W.↗