Search NASA⌕ Search

SEARCH · Search NASA

Results for “Component Test Capability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Development of a 5-Component Balance for Water Tunnel Applications

The principal objective of this research/development effort was to develop a multi-component strain gage balance to measure both static and dynamic forces and moments on models tested in flow visualization water tunnels. A balance was designed that allows measuring normal and side forces, and pitching, yawing and rolling moments (no axial force). The balance mounts internally in the model and is used in a manner typical of wind tunnel balances. The key differences between a water tunnel balance and a wind tunnel balance are the requirement for very high sensitivity since the loads are very low (typical normal force is 90 grams or 0.2 lbs), the need for water proofing the gage elements, and the small size required to fit into typical water tunnel models. The five-component balance was calibrated and demonstrated linearity in the responses of the primary components to applied loads, very low interactions between the sections and no hysteresis. Static experiments were conducted in the Eidetics water tunnel with delta wings and F/A-18 models. The data were compared to forces and moments from wind tunnel tests of the same or similar configurations. The comparison showed very good agreement, providing confidence that loads can be measured accurately in the water tunnel with a relatively simple multi-component internal balance. The success of the static experiments encouraged the use of the balance for dynamic experiments. Among the advantages of conducting dynamic tests in a water tunnel are less demanding motion and data acquisition rates than in a wind tunnel test (because of the low-speed flow) and the capability of performing flow visualization and force/moment (F/M) measurements simultaneously with relative simplicity. This capability of simultaneous flow visualization and for F/M measurements proved extremely useful to explain the results obtained during these dynamic tests. In general, the development of this balance should encourage the use of water tunnels for a wider range of quantitative and qualitative experiments, especially during the preliminary phase of aircraft design.

Suarez, Carlos J.↗

Thermal Design and Analysis for the Cryogenic MIDAS Experiment

The Materials In Devices As Superconductors (MIDAS) spaceflight experiment is a NASA payload which launched in September 1996 on the Shuttle, and was transferred to the Mir Space Station for several months of operation. MIDAS was developed and built at NASA Langley Research Center (LaRC). The primary objective of the experiment was to determine the effects of microgravity and spaceflight on the electrical properties of high-temperature superconductive (HTS) materials. The thermal challenge on MIDAS was to maintain the superconductive specimens at or below 80 K for the entire operation of the experiment, including all ground testing and 90 days of spaceflight operation. Cooling was provided by a small tactical cryocooler. The superconductive specimens and the coldfinger of the cryocooler were mounted in a vacuum chamber, with vacuum levels maintained by an ion pump. The entire experiment was mounted for operation in a stowage locker inside Mir, with the only heat dissipation capability provided by a cooling fan exhausting to the habitable compartment. The thermal environment on Mir can potentially vary over the range 5 to 40 C; this was the range used in testing, and this wide range adds to the difficulty in managing the power dissipated from the experiment's active components. Many issues in the thermal design are discussed, including: thermal isolation methods for the cryogenic samples; design for cooling to cryogenic temperatures; cryogenic epoxy bonds; management of ambient temperature components self-heating; and fan cooling of the enclosed locker. Results of the design are also considered, including the thermal gradients across the HTS samples and cryogenic thermal strap, electronics and thermal sensor cryogenic performance, and differences between ground and flight performance. Modeling was performed in both SINDA-85 and MSC/PATRAN (with direct geometry import from the CAD design tool Pro/Engineer). Advantages of both types of models are discussed. Correlation of several models to ground testing and flight data (where available) is presented. Both SINDA and PATRAN models predicted the actual thermal performance of the experiment well, even without post-flight correlation adjustments of the models.

Amundsen, Ruth McElroy↗

Feasibility of Actively Cooled Silicon Nitride Airfoil for Turbine Applications Demonstrated

Nickel-base superalloys currently limit gas turbine engine performance. Active cooling has extended the temperature range of service of nickel-base superalloys in current gas turbine engines, but the margin for further improvement appears modest. Therefore, significant advancements in materials technology are needed to raise turbine inlet temperatures above 2400 F to increase engine specific thrust and operating efficiency. Because of their low density and high-temperature strength and thermal conductivity, in situ toughened silicon nitride ceramics have received a great deal of attention for cooled structures. However, the high processing costs and low impact resistance of silicon nitride ceramics have proven to be major obstacles for widespread applications. Advanced rapid prototyping technology in combination with conventional gel casting and sintering can reduce high processing costs and may offer an affordable manufacturing approach. Researchers at the NASA Glenn Research Center, in cooperation with a local university and an aerospace company, are developing actively cooled and functionally graded ceramic structures. The objective of this program is to develop cost-effective manufacturing technology and experimental and analytical capabilities for environmentally stable, aerodynamically efficient, foreign-object-damage-resistant, in situ toughened silicon nitride turbine nozzle vanes, and to test these vanes under simulated engine conditions. Starting with computer aided design (CAD) files of an airfoil and a flat plate with internal cooling passages, the permanent and removable mold components for gel casting ceramic slips were made by stereolithography and Sanders machines, respectively. The gel-cast part was dried and sintered to final shape. Several in situ toughened silicon nitride generic airfoils with internal cooling passages have been fabricated. The uncoated and thermal barrier coated airfoils and flat plates were burner rig tested for 30 min without and with air cooling. Without cooling, the surface temperature of the flat plate reached approximately 2350 F. Starting with computer aided design (CAD) files of an airfoil and a flat plate with internal cooling passages, the permanent and removable mold components for gel casting ceramic slips were made by stereolithography and Sanders machines, respectively. The gel-cast part was dried and sintered to final shape. Several in situ toughened silicon nitride generic airfoils with internal cooling passages have been fabricated. The uncoated and thermal barrier coated airfoils and flat plates were burner rig tested for 30 min without and with air cooling. Without cooling, the surface temperature of the flat plate reached approximately 2350 F. With cooling, the surface temperature decreased to approximately 1910 F--a drop of approximately 440 F. This preliminary study demonstrates that a near-net-shape silicon nitride airfoil can be fabricated and that silicon nitride can sustain severe thermal shock and the thermal gradients induced by cooling and, thus, is a viable candidate for cooled components.

Bhatt, Ramakrishna T.↗

Small Payload Launch Integrated Testing Services (SPLITS) - SPSDL

My experience working on the Small Payload Launch Integrated Testing Services project has been both educational and rewarding. I have been given the opportunity to work on and experiment with a number of exciting projects and initiatives, each offering different challenges and opportunities for teamwork and collaboration. One of my assignments is to aid in the design and construction of a small-scale two stage rocket as part of a Rocket University initiative. My duties include programming a microcontroller to control the various sensors on the rocket as well as process and transmit data. Additionally, I am writing a graphical user interface application for the ground station that will receive the transmitted data from the rocket and display the information on screen along with a 3D rendering displaying the rocket orientation. Another project I am working on is to design and develop the avionics that will be used to control a high altitude balloon flight that will test a sensor called a Micro Dosimeter that will measure the total ionizing dose absorbed by electrical components during a flight. This includes assembling and soldering the various sensors and components, programming a microcontroller to input and process data from the Micro Dosimeter, and transmitting the data down to a ground station as well as save the data to an on-board SD card. Additionally, I am aiding in the setup and development of ITOS (Integrated Test and Operations System) capability in the SPSDL (Spaceport Processing System Development Lab).

Intern↗

Advanced Environmental Barrier Coating Development for SiC-SiC Ceramic Matrix Composite Components

This presentation reviews the NASA advanced environmental barrier coating (EBC) system development for SiCSiC Ceramic Matrix Composite (CMC) components for next generation turbine engines. The emphasis has been placed on the current design challenges of the 2700F environmental barrier coatings; coating processing and integration with SiCSiC CMCs and component systems; and performance evaluation and demonstration of EBC-CMC systems. This presentation also highlights the EBC-CMC system temperature capability and durability improvements through advanced compositions and architecture designs, as shown in recent simulated engine high heat flux, combustion environment, in conjunction with mechanical creep and fatigue loading testing conditions.

Simulated Engine Test↗

Effect of Geometric Fidelity on the Aerodynamics of a Swept Wing with Glaze Ice Accretion

Aerodynamic assessment of icing effects on swept wings is an important component of a larger effort to improve three-dimensional icing simulation capabilities. An understanding of ice-shape geometric fidelity on iced-wing aerodynamics and the associated flowfield features are needed to guide the development and validation of ice-accretion simulation tools. To this end, wind-tunnel testing was carried out for 8.9% and 13.3% scale semispan wing models based upon the Common Research Model airplane configuration. Various levels of geometric fidelity of an artificial ice shape representing a glaze-ice accretion on a swept wing were investigated. The highest fidelity artificial ice shape reproduced all of the three-dimensional features associated with the glaze ice accretion. The lowest fidelity artificial ice shapes were simple, spanwise-varying horn ice geometries intended to represent the maximum ice thickness on the wing upper surface. The results presented in this paper show that the addition of grit roughness to some lower-fidelity artificial ice shapes resulted in favorable lift and pitching moment comparisons to the wing with the highest fidelity artificial ice shape. In the range of 4.3 to 7.4 deg. angle of attack, surface oil flow visualization and pressure data show that the wing with the two lower fidelity simulations clearly demonstrated a leading edge vortex dominated flowfield, referred to as type I. For the wing with the high fidelity ice shape, the flowfield at lower angles of attack was characterized by streamwise-running, counter-rotating vortical flow referred to as type II. Between 6.4 and 7.4 deg. angle of attack, the effect of the type II flow structures was significantly altered and gave way to the type I leading edge vortex. This means that for angles of attack 7.4 deg. and higher, the wing with all three configurations exhibited the same type of flowfield. This helps to explain why there is reasonably good agreement in the lift and pitching moment coefficients among these configurations.

Aircraft icing↗

Advancing Dust Tolerant Mechanisms for a Sustained Exploration of the Moon

Introduction: “I think dust is probably one of our greatest inhibitors to a nominal operation on the Moon. I think we can overcome other physio-logical or physical or mechanical problems except dust.”– Gene Cernan, Apollo 17 Technical Debrief The Apollo missions revealed the impact of lu-nar dust on mechanisms. Lunar dust particles are jagged and electrostatically charged, giving them the ability to bind or damage mechanisms and alter thermal properties. Reports documented clogged equipment and jammed mechanisms in every mission, regardless of surface duration, as well as clogged mechanisms in the Extravehicular Mobility Suit (EMS), including zippers, wrist and hose locks, faceplates, and sunshades [1-2]. Several astronauts remarked they could not have sustained surface activity much longer because clogged joints would have frozen up completely [2]. Effective dust mitigation strategies are need-ed to support longer duration stays on the lunar surface [3-4]. State of the Art: Technology for mechanisms able to operate in dusty enviroments is advancing rapidly due to the needs of both Mars rovers and the Artemis program. Vacuum-tight connectors are essential for spacesuits and habitats, and their performance can be dependent on cleaning technologies, which have proven difficult on the lunar surface. Several TRL 3-5 technologies are undergoing tests with the expectation to reach TRL 6 within 1-2 years. Some mechanisms will be infused and tested on the VIPER (Volatiles Inves-tigating Polar Exploration Rover) mission planned for mid-2020s. NASA Funded Efforts: NASA has recognized the need for dust tolerant mechanisms, and has partnered with industry to advance the state-of-the-art. At NASA GRC, KSC, and JSC, the Dust Tolerant Mechanisms Project is working to devel-op advanced actuator seals for rotary joints and rotary bearing technologies for long-term sus-tained operation in lunar dust environments. An-other NASA project at NASA GRC, partnered with GSFC, JPL, and KSC is Motors for Dusty & Ex-treme Cold Environments (MDECE). MDECE is developing an unheated magnetically-geared mo-tor that can operate continuously for a long dura-tion at an ambient temperature of -243 ºC (33 K). NASA GRC has the capability to characterize the effects of dust on seals, mechanisms, and other mating surfaces and components under lunar conditions [5]. Through the SBIR/STTR program, NASA has funded several companies to advance dust toler-ant mechanisms via the Dust Tolerant Mecha-nisms sub-topic with applications in surface mobil-ity, spacesuits, connectors, joints, and more. LSIC and Community Efforts: The Lunar Surface Innovation Consortium (LSIC) Dust Miti-gation focus group has fostered collaborations across NASA, industry, and academia to develop solutions that minimizes the impact of lunar dust on robotic and human systems. Community ef-forts have included topical meetings on dust tol-erant mechanisms, featured technology presenta-tions, and feedback to NASA on potential gaps and needs. Testing: In 2021, NASA released NASA-STD-1008 [6]. This NASA Technical Standard estab-lishes minimum requirements and provides guid-ance for testing systems and hardware to be ex-posed to dust in planetary environments. The standard has specific sections dedicated to Mechanisms Testing (e.g. bearings, gears) as well as Seals and Mating Surfaces Testing (e.g. hatches, docking systems). Gaps and Needs: NASA is tracking dust tol-erant mechanisms as a gap in a cross-directorate analysis of capability areas needed to enable fu-ture human space-flight architectures. Two high-priority gap areas include additional facilities for testing mechanisms in lunar-surface conditions, and a better understanding of vulnerabilities to the smallest, nanometer-scale dust particles. Conclusion: Understanding and mitigating lu-nar dust is critical to successful, sustained opera-tions on the lunar surface – whether autonomous or otherwise. This presentation will discuss both the state-of-the-art and open needs in lunar dust tolerant mechanisms, technology impacts, mitiga-tion approaches, testing, LSIC community efforts, and more. References: [1] Gaier, J. R. (2020). The Im-pact of Dust on Lunar Surface Equipment During Apollo. Lunar Dust 2020. [2] GRC, & Gaier, J. R. (2005). The Effects of Lunar Dust on EVA Sys-tems During the Apollo Missions. [3] Johansen, M. R. (2020). An Update on NASA’s Lunar Dust Mitigation Strategy. Lunar Dust 2020. [4] ASI, CSA, ESA, JAXA, & NASA. (2016). Dust Mitiga-tion Gap Assessment Report. [5] Jimenez, N. et al (2022), LPSC Abstract 2572. [6] NASA-STD-1008, 2021.

J I Nunez↗

Survivability characteristics of composite compression structure

Test and evaluation was performed to determine the compression residual capability of graphite reinforced composite panels following perforation by high-velocity fragments representative of combat threats. Assessments were made of the size of the ballistic damage, the effect of applied compression load at impact, damage growth during cyclic loading and residual static strength. Several fiber/matrix systems were investigated including high-strain fibers, tough epoxies, and APC-2 thermoplastic. Additionally, several laminate configurations were evaluated including hard and soft laminates and the incorporation of buffer strips and stitching for improved damage resistance of tolerance. Both panels (12 x 20-inches) and full scale box-beam components were tested to assure scalability of results. The evaluation generally showed small differences in the responses of the material systems tested. The soft laminate configurations with concentrated reinforcement exhibited the highest residual strength. Ballistic damage did not grow or increase in severity as a result of cyclic loading, and the effects of applied load at impact were not significant under the conditions tested.

Avery, John G.↗

Development of a comprehensive analysis for rotorcraft. I - Rotor model and wake analysis

The development of a comprehensive analytical model of rotorcraft aerodynamics and dynamics is described. Particular emphasis is given to describing the reasons behind the choices and decisions involved in constructing the model. The analysis is designed to calculate rotor performance, loads and noise; helicopter vibration and gust response; flight dynamics and handling qualities; and system aeroelastic stability. It is intended for use in the design, testing and evaluation of a wide class of rotors and rotorcraft, and to be the basis for further development of rotary wing theories. The general characteristics of the geometric, structural, inertial, and aerodynamic models used for the rotorcraft components are described, including the assumptions introduced by the chosen models and the resulting capabilities and limitations. Finally, some examples from recent applications of the analysis are given.

Johnson, W.↗

Development of a comprehensive analysis for rotorcraft. II - Aircraft model, solution procedure and applications

The development of a comprehensive analytical model of rotorcraft aerodynamics and dynamics is described. Particular emphasis is given to describing the reasons behind the choices and decisions involved in constructing the model. The analysis is designed to calculate rotor performance, loads and noise; helicopter vibration and gust response; flight dynamics and handling qualities; and system aeroelastic stability. It is intended for use in the design, testing and evaluation of a wide class of rotors and rotorcraft and to be the basis for further development of rotary wing theories. The general characteristics of the geometric, structural, inertial and aerodynamic models used for the rotorcraft components are described, including the assumptions introduced by the chosen models and the resulting capabilities and limitations. Finally, some examples from recent applications of the analysis are given.

Johnson, W.↗

Strain isolated ceramic coatings

Plasma sprayed ceramic coatings are used in gas turbine engines to improve component temperature capability and cooling air efficiency. A compliant metal fiber strain isolator between a plasma sprayed ceramic coating and a metal substrate improves ceramic durability while allowing thicker coatings for better insulation. Development of strain isolated coatings has concentrated on design and fabrication of coatings and coating evaluation via thermal shock testing. In thermal shock testing, five types of failure are possible: buckling failure im compression on heat up, bimetal type failure, isothermal expansion mismatch failure, mudflat cracking during cool down, and long term fatigue. A primary failure mode for thermally cycled coatings is designated bimetal type failure. Bimetal failure is tensile failure in the ceramic near the ceramic-metal interface. One of the significant benefits of the strain isolator is an insulating layer protecting the metal substrate from heat deformation and thereby preventing bimetal type failure.

Tolokan, R. P.↗

Experimental and Analytical Determinations of Spiral Bevel Gear-Tooth Bending Stress Compared

Spiral bevel gears are currently used in all main-rotor drive systems for rotorcraft produced in the United States. Applications such as these need spiral bevel gears to turn the corner from the horizontal gas turbine engine to the vertical rotor shaft. These gears must typically operate at extremely high rotational speeds and carry high power levels. With these difficult operating conditions, an improved analytical capability is paramount to increasing aircraft safety and reliability. Also, literature on the analysis and testing of spiral bevel gears has been very sparse in comparison to that for parallel axis gears. This is due to the complex geometry of this type of gear and to the specialized test equipment necessary to test these components. To develop an analytical model of spiral bevel gears, researchers use differential geometry methods to model the manufacturing kinematics. A three-dimensional spiral bevel gear modeling method was developed that uses finite elements for the structural analysis. This method was used to analyze the three-dimensional contact pattern between the test pinion and gear used in the Spiral Bevel Gear Test Facility at the NASA Glenn Research Center at Lewis Field. Results of this analysis are illustrated in the preceding figure. The development of the analytical method was a joint endeavor between NASA Glenn, the U.S. Army Research Laboratory, and the University of North Dakota.

Handschuh, Robert F.↗

Thermo-Mechanical Properties of Super Sylramic SiC Fibers

Ceramic matrix composites (CMC) reinforced by Sic fibers, such as SiC/SiC, are targeted for application in hot-section components of advanced engines for aerospace propulsion and for electrical power generation. Two Super Sylramic Sic fiber types recently developed at NASA using the Sylramic fiber from COI Ceramics are candidates fof providing these components with improved thermal capability and improved performance. This paper reports on the state-of-the-art ability of these new fiber types to meet the key fiber requirements of these applications: high strength, high creep-rupture resistance, high environmental resistance, and high thermal conductivity. For example, creep-rupture tests performed at from 1350 to 1500 C under various environments to simulate CMC fabrication and service conditions show creep resistance in air improved -20 and -7 times in comparison to current Sylramic and Sylramic-iBN fiber types, respectively. This in turn resulted in an increase in fiber rupture life by up to two orders of magnitude. TEM and AES microscopic observations are presented to indicate that these improvements can be correlated with the replacement of weak grain boundary phases with stronger phases that hinder grain boundary sliding more effectively. SiC/SiC composite results are also provided to show the advantages of the Super Sylramic fiber types both for CMC fabrication and high temperature application.

Yun, H. M.↗

Experimental Aerodynamic Simulation of Glaze Ice Accretion on a Swept Wing

Aerodynamic assessment of icing effects on swept wings is an important component of a larger effort to improve three-dimensional icing simulation capabilities. An understanding of ice-shape geometric fidelity and Reynolds and Mach number effects on iced-wing aerodynamics is needed to guide the development and validation of ice-accretion simulation tools. To this end, wind-tunnel testing was carried out for 8.9% and 13.3% scale semispan wing models based upon the Common Research Model airplane configuration. Various levels of geometric fidelity of an artificial ice shape representing a realistic glaze-ice accretion on a swept wing were investigated. The highest fidelity artificial ice shape reproduced all of the three-dimensional features associated with the glaze ice accretion. The lowest fidelity artificial ice shapes were simple, spanwise-varying horn ice geometries intended to represent the maximum ice thickness on the wing upper surface. The results presented in this paper show that changes in Reynolds and Mach number have only a small effect on the iced-wing aerodynamics relative to the clean-wing configuration. Furthermore, the addition of grit roughness to some lower-fidelity artificial ice shapes resulted in favorable lift and pitching moment comparisons to the wing with the highest fidelity artificial ice shape. For the wing with simple horn ice shapes, the dependence of maximum lift coefficient on horn height and angle are generally consistent with the trends observed for similar experiments conducted on iced airfoils in past research. In terms of usable lift however, the horn height did have a significant effect even for lower horn angles. This could be an important finding since usable lift may be more indicative of the impending iced-swept wing stall and need for additional pitch control than maximum lift coefficient.

Broeren, Andy P.↗

An Agile-Like Approach to Hardware Development: The Ejectable Data Recorder (EDR) for Orion's Ascent Abort 2 (AA-2) Test Flight

On July 2, 2019, the Ascent Abort 2 (AA-2) Flight Test Vehicle was launched from Cape Canaveral, with the goal of demonstrating the performance of Orion’s Launch Abort System (LAS) and collecting data from hundreds of sensors throughout the vehicle. The data collected during this test flight is of paramount importance, as it will be used to certify the Orion vehicle for human spaceflight. Originally, the data was to be downlinked via a single string network of antennas on the LAS, with the associated risk of potential data dropouts, as well as loss of data once the LAS was jettisoned. Thus, additional antennas were added onto the crew module (CM) to support data downlink post-LAS jettison, a buffer rebroadcast capability was added to fill in any gaps in data downlink transmissions, and an ejectable data recorder (EDR) subsystem was added to the CM as a redundant measure to collect all the instrumentation data. The EDR subsystem was added to the project about one year after the project commenced, which significantly reduced the available development time when compared with the other subsystems of the AA-2 Test Flight. The project was further accelerated by six months, around the critical design review gate. Due to the schedule compression challenge and the fact that the EDR subsystem was a backup system and not flight critical, the EDR subsystem was further challenged to find a new and more efficient way to develop hardware. Thus, the EDR subsystem experimented with different management and systems engineering processes, team sizes, communication methods, and tools. Some examples are novel uses of SharePoint as a Data-centric Project Management & Systems Engineering environment, a continuous testing approach through the lifecycle, and a Skunkworks approach to managing the team. The EDR subsystem blended Commercial Off The Shelf (COTS) hardware with in-house developed hardware and software to create a novel data retrieval capability. The capability evolved rapidly through a hardware in the loop simulation environment that enabled incremental component updates for not only the EDR subsystem but across the entire Crew Module. This paper will present an overview of how the EDR subsystem was managed and compare it to an Agile approach to managing projects. The paper will further provide a recommended approach to future Agile-like hardware development that incorporates lessons learned from the EDR experience.

Agile↗

A Fast Evaluation of PDA Experimental Parameters Using Mie Scattering to Enhance the Measurement Accuracy of Droplet Size Distributions

The Phase Doppler technique (PDA) and its implementation generally relies on a geometric optics formulation for light scattering to estimate drop sizes from the measured phase differences between Doppler signals from two or more detectors. Although this limits experimental PDA scattering geometries to those where only one component of the geometric scatter is dominant, the calculations are relatively simple. This TM describes a fast method to evaluate PDA experimental parameters analytically using Mie scattering that provides a performance estimate of all possible configurations. The best configurations are fully tested using a Monte Carlo simulation to obtain a more accurate capability estimate for each one.

PDA↗

SSME structural dynamic model development, phase 2

A set of test correlated mathematical models of the SSME High Pressure Oxygen Turbopump (HPOTP) housing and rotor assembly was produced. New analysis methods within the EISI/EAL and SPAR systems were investigated and runstreams for future use were developed. The LOX pump models have undergone extensive modification since the first phase of this effort was completed. The rotor assembly from the original model was abandoned and a new, more detailed model constructed. A description of the new rotor math model is presented. Also, the pump housing model was continually modified as additional test data have become available. This model is documented along with measured test results. Many of the more advanced features of the EAL/SPAR finite element analysis system were exercised. These included the cyclic symmetry option, the macro-element procedures, and the fluid analysis capability. In addition, a new tool was developed that allows an automated analysis of a disjoint structure in terms of its component modes. A complete description of the implementation of the Craig-Bampton method is given along with two worked examples.

Foley, M. J.↗

Development of circulation control technology for powered-lift STOL aircraft

The flow entraining capabilities of the Circulation Control Wing high lift system were employed to provide an even stronger STOL potential when synergistically combined with upper surface mounted engines. The resulting configurations generate very high supercirculation lift in addition to a vertical component of the pneumatically deflected engine thrust. A series of small scale wind tunnel tests and full scale static thrust deflection tests are discussed which provide a sufficient data base performance. These tests results show thrust deflections of greater than 90 deg produced pneumatically by nonmoving aerodynamic surfaces, and the ability to maintain constant high lift while varying the propulsive force from high thrust recovery required for short takeoff to high drag generation required for short low speed landings.

Englar, Robert J.↗