Search NASA⌕ Search

SEARCH · Search NASA

Results for “Computational Fluid Dynamics Conduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Validation of a Computational Fluid Dynamics Model of Axial Jet Mixing for Cryogenic Propellant Tank Pressure Control

The Fluid Dynamics Branch at the NASA Marshall Space Flight Center is preparing to support flight programs through analysis of a variety of cryogenic fluid management (CFM) applications. Many vehicles being considered for future manned missions to the moon and beyond use chemical or nuclear thermal propulsion systems that rely on cryogenic propellants. Storing cryogenic propellants for later use is a challenge, though. Many areas of active CFM research, testing, and design involve propellant conditioning to ensure propellant remains a usable liquid for propulsion. Multiple technologies may be used to achieve adequate conditioning including the subject of this paper, a jet-based mixer. Mixing serves to homogenize fluid temperatures and decrease ullage pressure. Development and validation of a modeling methodology for jet-based mixing was conducted to prepare for in-line design work.

Jacob M. Brodnick↗

Simulation of fluid flows during growth of organic crystals in microgravity

Several counter diffusion type crystal growth experiments were conducted in space. Improvements in crystal size and quality are attributed to reduced natural convection in the microgravity environment. One series of experiments called DMOS (Diffusive Mixing of Organic Solutions) was designed and conducted by researchers at the 3M Corporation and flown by NASA on the space shuttle. Since only limited information about the mixing process is available from the space experiments, a series of ground based experiments was conducted to further investigate the fluid dynamics within the DMOS crystal growth cell. Solutions with density differences in the range of 10 to the -7 to 10 to the -4 power g/cc were used to simulate microgravity conditions. The small density differences were obtained by mixing D2O and H2O. Methylene blue dye was used to enhance flow visualization. The extent of mixing was measured photometrically using the 662 nm absorbance peak of the dye. Results indicate that extensive mixing by natural convection can occur even under microgravity conditions. This is qualitatively consistent with results of a simple scaling analysis. Quantitave results are in close agreement with ongoing computational modeling analysis.

Roberts, Gary D.↗

Numerical Study of Vortex Core in Turbulent Swirling Flow

Swirling flow has attracted a great deal of research interest. An application of swirling flow can be found in many engineering areas; such as gas cyclone and heat transfer enhancement. In nuclear engineering, swirling flow is used as heat transfer enhancement in rod bundle by installing grid spacer and mixing vane. Because of its extensive applications, there has been a great number of experimental and numerical investigations of swirling flow. McClusky et al., experimentally studied mapping of the lateral velocity in rod bundle using Laser Doppler Velocimetry (LDV) and Conner et al. predicted the flow field in rod bundle by CFD. To understand the characteristics of swirling flow such as tangential velocity and vortex core swirling flow, some researchers investigated swirling flow in a pipe instead of in rod bundle. This is due to the similarity between swirling flow in a pipe and rod bundle. In recent study, flow mapping of 2D velocity field of single-phase swirling flow had been conducted experimentally by Particle Image Velocimetry (PIV). However, this method needs calibration and complicated. The new measurement technique for flow mapping in swirling flow was done by phased array Ultrasonic Velocity Profiler (PAUVP). Hamdani et al., successfully plotted velocity field and determined the swirling core region (vortex core). This technique is nonintrusive and no need calibration. However, there was a limitation of the measurement because phased array UVP cannot capture 360 deg. velocity field inside the pipe. In addition, tangential velocity in CFD results was not agree well with experiment data due asymmetric problem. To evaluate this limitation of experimental method, the numerical simulations using Computational Fluid Dynamics (CFD) needs to be performed. The objective of this study is to use the commercial CFD code Fluent to model the developing turbulent swirling flow induced by twisted tape inside a straight pipe, and to gain an understanding of such a flow and the turbulence models involved in the simulation. Straight pipe is used instead of rod bundle for a simplification. In this work, the Renormalized Group (RNG) k-{epsilon} turbulence model and Reynolds Stress Model (RSM) turbulence model, are performed to study the phenomena of vortex core in a pipe with twisted tape inserts. Effects of the Reynolds number and asymmetric of twisted tape (inclination, {alpha} = 5 deg. and {alpha} = 20 deg.) on swirling core position are examined using water as the testing fluid. Furthermore, the Navier-Stokes equations will be solved to obtain results that can be validated with the previous experimental results. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Investigating the Role of VR in a Simulation-Based Medical Planning System for Coronary Interventions

Virtual reality (VR) based computational fluid dynamics (CFD) simulations are emerging as a viable solution to guide complex surgical or invasive procedures, such as percutaneous coronary intervention (PCI), as they enable a realistic first-person experience of underlying patient anatomy and physiology. Realistic VR experience can be assessed by immersion, an objective VR property. However, it remains unclear how immersion influences virtual PCI procedures and what level of immersion is required. This study answers both these questions by evaluating the application of a CFD-based VR system and comparing semi-immersive and fully immersive VR displays. Nine patient-specific arterial models were simulated using CFD and used to conduct a quantitative user evaluation (n = 31) with both types of VR displays. The findings of this study reveal that VR immersion significantly improves the accuracy of simulated stent placement in complex arterial geometries, relative to traditional desktops with no immersion (p < 0.05). Higher accuracy is noted by the use of semi-immersive VR display, which offers higher display fidelity as compared to the fully immersive VR display (p < 0.05). Interestingly, CFD data mapped on to arterial geometries strongly influences the location of stent placement. This finding is demonstrated by the lack of significant accuracy deviation between the two immersive displays when CFD data is shown. This study provides compelling evidence that a CFD-based VR system rendered on semi-immersive displays can enable more accurate and efficient stent placement.

Vardhan, Madhurima↗

Dual-Mode Combustion

The Department of Mechanical and Aerospace Engineering at the University of Virginia has conducted an investigation of the mixing and combustion processes in a hydrogen fueled dual-mode scramjet combustor. The experiment essentially consisted of the "direct connect" continuous operation of a Mach 2 rectangular combustor with a single unswept ramp fuel injector. The stagnation enthalpy of the test flow simulated a flight Mach number of 5. Measurements were obtained using conventional wall instrumentation and laser based diagnostics. These diagnostics included, pressure and wall temperature measurements, Fuel Plume Imaging (FPI) and Particle Image Velocimetry (PIV). A schematic of the combustor configuration and a summary of the measurements obtained are presented. The experimental work at UVa was parallel by Computational Fluid Dynamics (CFD) work at NASA Langley. The numerical and experiment results are compared in this document.

Goyne, Christopher P.↗

CFD Study of the Hydrocarbon Boost Low-Pressure Inducer and Kicker in the Presence of a Circumferential Groove

Results are presented of a computational fluid dynamics (CFD) study done in support of Marshall Space Flight Center's (MSFC) sub-scale water flow experiments of the Hydrocarbon Boost (HCB) Oxidizer Turbopump (OTP) being developed by the Air Force Research Laboratory (AFRL) and Aerojet. A circumferential groove may be added to the pump to reduce synchronous cavitation and subsequent bearing loads at a minimal performance cost. However, the energy may reappear as high order cavitation (HOC) that spans a relatively large frequency range. Thus, HOC may have implications for the full-scale OTP inducer in terms of reduced structural margin at higher mode frequencies. Simulations using the LOCI/Stream CFD program were conducted in order to explore the fluid dynamical impact of the groove on the low-pressure inducer and kicker. It was found that the circumferential groove has minimal head performance impact, but causes back-flowing high-swirl fluid to interact with the nearly-axial incoming fluid just above the inducer blades. The high-shear interface between the fluids is Kelvin-Helmholtz unstable, resulting in trains of low pressure regions or 'pearls' forming near the upstream edge of the groove. When the static pressure in these regions becomes low enough and they get cut by the blade leading edge, HOC is thought to occur. Although further work is required, the numerical models indicate that HOC will occur in the runbox of the AFRL/Aerojet HCB OTP. Comparisons to the ongoing water flow experiments will be discussed, as well as possible designs that may mitigate HOC while continuing to reduce synchronous cavitation. December 2011 MSS/LPS/SPS Joint Subcommittee Meeting ABSTRACT SUBMITTAL FORM

Coker, Robert↗

Visualization of Freestream Vortices in the NASA Langley 4-Foot Supersonic Unitary Plan Wind Tunnel

Streamwise vortices present in the freestream of the NASA Langley 4-Foot Supersonic Unitary Plan Wind Tunnel have been observed experimentally for the first time. A high-energy, burst-mode laser system was used to conduct time-resolved planar laser Mie scattering in the freestream of this facility. The freestream of the facility was observed over Mach numbers ranging from 2.4 to 4.6 and (unit) Reynolds number between 3.3 × 10 6 to 14.8 × 10 6 1/m. Apparent vortical structures were observed in the tunnel freestream at Mach numbers ≤ 3 with little difference observed for varying Reynolds number. With further-increasing Mach number, protrusive and oscillatory vertical ‘sprite’ structures were observed emanating from the tunnel floor boundary layer. Neither of these structural phenomena have been observed before experimentally in the facility and act to confirm and inform predictions made in computational fluid dynamic simulations of the facility.

Flow visualization↗

Visualization of Freestream Vortices in the NASA Langley 4-Foot Supersonic Unitary Plan Wind Tunnel

Streamwise vortices present in the freestream of the NASA Langley 4-Foot Supersonic Unitary Plan Wind Tunnel have been observed experimentally for the first time. A high-energy, burst-mode laser system was used to conduct time-resolved planar laser Mie scattering in the freestream of this facility. The freestream of the facility was observed over Mach numbers ranging from 2.4 to 4.6 and (unit) Reynolds number between 3.3 × 10 6 to 14.8 × 10 6 1/m. Apparent vortical structures were observed in the tunnel freestream at Mach numbers ≤ 3 with little difference observed for varying Reynolds number. With further-increasing Mach number, protrusive and oscillatory vertical ‘sprite’ structures were observed emanating from the tunnel floor boundary layer. Neither of these structural phenomena have been observed before experimentally in the facility and act to confirm and inform predictions made in computational fluid dynamic simulations of the facility.

Flow visualization↗

EXPERIMENTAL AND COMPUTATIONAL STUDY OF DIRECT CONTACT MEMBRANE DISTILLATION

Experimental and computational studies of direct contact membrane distillation (DCMD) are conducted. The permeate flux is measured in a module containing a flat sheet membrane. Polytetrafluoroethylene (PTFE) hydrophobic membrane (Membrane Solutions, FPB045A16) with a nominal pore size of 0.45 μm, the thickness of 179~239 μm, the porosity of 80% is used in the experiments. The feed solution is a binary mixture of water and NaCl. The inlet feed temperature is fixed at 70°C, and the feed Reynolds number is varied between 500 and 2000. Two inlet feed concentrations, 0 and 35g/L, are considered. The permeate flow rate was kept constant at Re of 1300 and temperature of 20°C. Three-dimensional steady-state computational fluid dynamics (CFD) simulations are performed using the laminar model. The Navier’s Stokes, energy, and mass transport equations in each channel coupled with flux boundary conditions imposed at the membrane surface are solved. The predicted module-averaged flux is compared to measured data for all operating conditions. Measured and predicted flux agrees well; validating both experiments and model, Temperature polarization in the feed and permeate channel and concentration polarization in the feed channel are characterized by validated CFD simulations.

Oztekin, Alparslan↗

Particle Image Velocimetry Measurements in a Wire-Wrapped 61-Pin Hexagonal Fuel Bundle

Liquid metal fast reactor fuel assemblies using sodium as a coolant typically utilize a tightly packed triangular lattice of fuel pins enclosed in a hexagonal duct. The fuel pins are typically wrapped with a helical wire spacer. The primary function of the wire spacers is to maintain a gap between neighboring fuel pins. They also mitigate vortex-induced vibration and enhance sub-channel mixing to increase convective heat transfer. Many experiments have been performed to study thermal-hydraulic characteristics, primarily pressure drops, of the wire-wrapped fuel bundles. Novendstern developed a semi-empirical model to predict pressure losses in a hexagonal array of wire-wrapped pins in the turbulent flow regime. Rehme proposed pressure drop correlations for a wide range of geometrical parameters, such as pitch-to-diameter ratio P/D from 1.125 to 1.417, lead-to-wire diameter ratio H / dm from 6 to 45, and number of pins n from 7 to 61. Cheng and Todreas introduced their hydrodynamic models for subchannel friction factors and mixing parameters in a 37-pin fuel bundle, which covered the laminar, transition and turbulent flow regimes. Computational fluid dynamics (CFD) offers an opportunity to validate the above correlations and investigate the flow characteristics in the subchannels. Several numerical studies of the wire-wrapped fuel bundles have been performed and most of them are Reynolds-Averaged Navier-Stokes (RANS) based simulations with various turbulence models. Ahmad and Kim performed RANS simulations of 7- and 19-pin bundles using the k-omega SST turbulent model, while Gajapathy et al. performed RANS simulations on 7-pin bundles using the k-epsilons model. Recently, Fischer et al. carried out large-eddy simulation (LES) calculations on wire-wrapped fuel bundles to obtain higher-resolution numerical solutions of subchannel behavior. The geometrical complexity of the hexagonal wire-wrapped fuel bundle has limited experimental activities to pressure drop measurements. A database of pressure drops and flow-field measurements in a 61-pin wire-wrapped hexagonal fuel bundle is not available to benchmark the existing correlations and validate the CFD calculations. Texas A and M University is conducting isothermal flow experiments in a wire-wrapped 61-pin hexagonal fuel bundle to support the research on advanced nuclear fuel development sponsored by the Department of Energy (DOE). The purpose of these tests is to perform high spatial and temporal resolution measurements of the flow and pressure measurements at different locations in the fuel bundle. The experimental facility employs matched-index-of-refraction (MIR) techniques and laser diagnostic velocity measurement techniques such as particle image velocimetry (PIV) and laser Doppler velocimetry (LDV). The result of this experimental activity will be an experimental database of pressure and flow-field measurements that will be suitable for validating CFD computer codes. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Influence of turbulence and thermophysical fluid properties on cavitation erosion predictions in channel flow geometries

Cavitation and cavitation-induced erosion have been observed in fuel injectors in regions of high acceleration and low pressure. Although these phenomena can have a large influence on the performance and lifetime of injector hardware, questions still remain on how these physics should be accurately and efficiently represented within a computational fluid dynamics model. While several studies have focused on the validation of cavitation predictions within canonical and realistic injector geometries, it is not well documented what influence the numerical and physical parameters selected to represent turbulence and phase change will have on the predictions for cavitation erosion propensity and severity. In this work, a range of numerical and physical parameters are evaluated within the mixture modeling approach in CONVERGE to understand their influence on predictions of cavitation, condensation and erosion. Particular attention is paid to grid resolution, turbulence model and near-wall treatment, fuel surrogate properties, and non-condensable gas content. Assessment of cavitation predictions are conducted through comparison of measured and predicted mass flow rates and cavitation probability distributions for flow through a channel with a sharp inlet. Predictions for hydrodynamic impact loading and cavitation erosion are compared with the experimentally measured incubation period and critical site for erosion. Based on these findings, recommendations are provided for modeling turbulent cavitating flows, using the single fluid mixture modeling approach, to improve predictions for cavitation-induced erosion. In particular, to capture the fluid dynamic phenomena characterizing cavitation cloud formation, development and shedding, a Large Eddy simulation with grid resolution as fine as 2.50 μm is recommended. The assumed concentration of non-condensable gas content is observed to have a strong influence on the predicted cavitation erosion severity, which motivates the need for dissolved gas concentration measurements for future cavitation erosion experimental studies. Using the best practices established in this work, good agreement is achieved between the measured and predicted cavitation parameters, as well as the critical site for cavitation-induced erosion.

Magnotti, Gina Maureen↗

SSME HPOTP impeller backcavity CFD analysis

The ball bearings behind the Space Shuttle Main Engine (SSME) HPOTP preburner pump have a history of premature wear requiring their replacement. Extensive tests have been conducted in an attempt to identify the operating factors that contribute to the wear. It has been conjectured that the coolant inflow velocity swirl pattern can aid bearing operation by matching ball orbit speed and thus affect bearing life. However, control of the velocity distribution up to now could only be achieved by trial and error following hardware testing. Observation of hardware from recent flight and development operation led to the hypothesis that certain assemblies with more extensive grinding patterns on the backwall of the impeller for rotor balancing correlated with improved bearing wear. To analytically evaluate the effect of cavity configuration on the flowfield, 3-D computational fluid dynamics (CFD) analyses of various geometries was successfully executed using REACT3D. Height of the anti-vortex ribs on the stationary wall was varied, as was the configuration of the rotating wall, from smooth to simulations of various grindout patterns. The results obtained indicate the effects of the various geometries and provide valuable guidelines for cavity modification to optimize bearing cooling.

Hsu, W. W.↗

Steady pressure measurements on an Aeroelastic Research Wing (ARW-2)

Transonic steady and unsteady pressure tests have been conducted in the Langley transonic dynamics tunnel on a large elastic wing known as the DAST ARW-2. The wing has a supercritical airfoil, an aspect ratio of 10.3, a leading-edge sweep back angle of 28.8 degrees, and two inboard and one outboard trailing-edge control surfaces. Only the outboard control surface was deflected to generate steady and unsteady flow over the wing during this study. Only the steady surface pressure, control-surface hinge moment, wing-tip deflection, and wing-root bending moment measurements are presented. The results from this elastic wing test are in tabulated form to assist in calibrating advanced computational fluid dynamics (CFD) algorithms.

Sandford, Maynard C.↗

An Initial Non-Equilibrium Porous-Media Model for CFD Simulation of Stirling Regenerators

The objective of this paper is to define empirical parameters for an initial thermal non-equilibrium porous-media model for use in Computational Fluid Dynamics (CFD) codes for simulation of Stirling regenerators. The two codes currently used at Glenn Research Center for Stirling modeling are Fluent and CFD-ACE. The codes porous-media models are equilibrium models, which assume solid matrix and fluid are in thermal equilibrium. This is believed to be a poor assumption for Stirling regenerators; Stirling 1-D regenerator models, used in Stirling design, use non-equilibrium regenerator models and suggest regenerator matrix and gas average temperatures can differ by several degrees at a given axial location and time during the cycle. Experimentally based information was used to define: hydrodynamic dispersion, permeability, inertial coefficient, fluid effective thermal conductivity, and fluid-solid heat transfer coefficient. Solid effective thermal conductivity was also estimated. Determination of model parameters was based on planned use in a CFD model of Infinia's Stirling Technology Demonstration Converter (TDC), which uses a random-fiber regenerator matrix. Emphasis is on use of available data to define empirical parameters needed in a thermal non-equilibrium porous media model for Stirling regenerator simulation. Such a model has not yet been implemented by the authors or their associates.

Tew, Roy C.↗

Trajectory Reconstruction and Uncertainty Analysis Using Mars Science Laboratory Pre-Flight Scale Model Aeroballistic Testing

As part of the Mars Science Laboratory (MSL) trajectory reconstruction effort at NASA Langley Research Center, free-flight aeroballistic experiments of instrumented MSL scale models was conducted at Aberdeen Proving Ground in Maryland. The models carried an inertial measurement unit (IMU) and a flush air data system (FADS) similar to the MSL Entry Atmospheric Data System (MEADS) that provided data types similar to those from the MSL entry. Multiple sources of redundant data were available, including tracking radar and on-board magnetometers. These experimental data enabled the testing and validation of the various tools and methodologies that will be used for MSL trajectory reconstruction. The aerodynamic parameters Mach number, angle of attack, and sideslip angle were estimated using minimum variance with a priori to combine the pressure data and pre-flight computational fluid dynamics (CFD) data. Both linear and non-linear pressure model terms were also estimated for each pressure transducer as a measure of the errors introduced by CFD and transducer calibration. Parameter uncertainties were estimated using a "consider parameters" approach.

Lugo, Rafael A.↗

Characterization of Contact and Bulk Thermal Resistance of Laminations for Electric Machines

Thermal management for electric motors is important as the automotive industry continues to transition to more electrically dominant vehicle propulsion systems. The transition to more electrically dominant propulsion systems leads to higher-power duty cycles for electric-drive systems. Thermal constraints place significant limitations on how electric motors ultimately perform. As thermal management improves, there will be a direct trade-off among motor performance, efficiency, cost, and the sizing of electric motors to operate within the thermal constraints. During the development of thermal finite element analysis models and computational fluid dynamics models for electric motors, it was found that there was a lack of open literature detailing the thermal properties of key materials common in electric motors that are significant in terms of heat removal. The lack of available literature, coupled with the strong interest from industry in the passive-stack thermal measurement results, led to experiments to characterize the thermal contact resistance between motor laminations. We examined four lamination materials, including the commonly used 26 gauge and 29 gauge M19 materials, the HF10 and Arnon 7 materials. These latter two materials are thinner and reduce eddy currents responsible for core losses. We measured the thermal conductivity of the lamination materials and the thermal contact resistance between laminations in a stack, as well as investigated factors affecting contact resistance between laminations such as the contact pressure and surface finish. Lamination property data will be provided and we also develop a model to estimate the through-stack thermal conductivity for materials beyond those that were directly tested in this work. For example, at a clamping pressure of 138 kPa, the 29 gauge M19 material has a through-stack thermal conductivity of 1.68 W/m-K, and the contact resistance between laminations was measured to be 193 mm^2-K/W. The measured bulk thermal conductivity for the M19 29 gauge material is 21.0 W/m-K. Density and specific heat were measured to be 7450 kg/m^3 and 463 J/kg-K, respectively. These results are helping, and will continue to help engineers and researchers in the design and development of motors.

33 ADVANCED PROPULSION SYSTEMS↗

Time-Resolved PIV/PTV Measurements on Interior Subchannels of a Wire-Wrapped 61-pin Hexagonal Fuel Bundle

Liquid metal fast reactor fuel bundles using sodium as a coolant typically utilize a tightly packed triangular lattice of fuel pins enclosed in a hexagonal duct. Often, the fuel pins are helically wrapped with a wire spacer. The primary function of the wire spacers is to maintain a gap between adjacent fuel pins. They also enhance sub-channel mixing to increase convective heat transfer and mitigate vortex-induced vibration. Texas A and M University has conducted isothermal flow experiments in a wire-wrapped 61-pin hexagonal fuel bundle to support the research on advanced nuclear fuel development sponsored by the Department of Energy (DOE). These tests produced high spatial and temporal resolution measurements of the velocity field and pressure at different locations in the fuel bundle. The experimental facility employs matched-index-of-refraction (MIR) techniques and laser diagnostic velocity measurement techniques such as particle image velocimetry (PIV), particle tracking velocimetry (PTV), and laser Doppler velocimetry (LDV). The result of this experimental activity will be an experimental database of pressure and velocity field measurements that will be suitable for validating computational fluid dynamics (CFD) methods, such as Reynolds-averaged Navier-Stokes (RANS) and highly resolved large eddy simulation (LES). PIV results on the set of edge subchannels near the hexagonal duct have been presented in another paper. This paper presents PIV results on two sets of interior subchannels, defined as Interior- 1 and Center-2, at a Reynolds number (Re) of 19,000 in the turbulent regime.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Progress on Demonstration of a MOOSE-Based Coupled Capability for Hot Channel Factors in Fast Reactors

Hot channel factors (HCFs) are computed values that account for the impact on predicted peak fuel, cladding, and coolant temperatures due to uncertainties in the as-built reactor’s material properties and geometry as well as uncertainties due to modeling approximations. Reduction in computed HCF values via reduction or elimination of modeling approximations may translate to significant economic savings if the reactor power can be raised due to the extra temperature margin gained. While limited historical datasets exist for sodium-cooled fast reactors (SFRs), there are no available HCF data for lead-cooled fast reactors (LFRs) outside of work generated previously within NEAMS. The computation of HCFs involves insights from reactor physics, thermal fluids and heat conduction calculations to determine how the peak temperatures respond to various uncertainties in the design. Due to the significant advantages for multi-physics coupling offered by the MOOSE framework, Griffin (MOOSE-based reactor physics code), MOOSE Heat Conduction Module, and Cardinal (MOOSE-wrapped multi-physics application which includes the NekRS thermal fluids code) are being coupled together using the MOOSE MultiApp System to develop a highfidelity multi-physics modeling capability for HCF simulations. This high-fidelity coupling workflow may also be beneficial for other fast reactor applications in the future. In previous work, Griffin and NekRS were individually assessed to ensure the necessary capabilities were in place. This work describes initial efforts to couple the codes (including folding in the MOOSE Heat Conduction Module) and determining the workflow for the perturbed calculations which will leverage the Stochastic Tools Module (STM). To our knowledge, this is the first coupling of Griffin and NekRS as well as the first exploratory use of Stochastic Tools Module for Cardinal. In this report, the neutronics code Griffin, the heat conduction solver in MOOSE, and the MOOSE-wrapped application containing NekRS (Cardinal) are linked together to demonstrate the coupled capability. Griffin and Cardinal are linked dynamically by specifying shared libraries. Different coupling hierarchies are tested for selecting the most appropriate coupling strategy. A coupling scheme is selected based on the efficiency of calculation and ease of data communication. Multiple tests are performed to choose suitable mesh structure, model configurations, scheme setup and boundary conditions to avoid loss of energy due to data interpolation between different modules or weak imposition of fluxes in finite element codes. Computational experiments are performed to study the tolerance control of each type of iteration to avoid false convergence. The coupled capability is demonstrated in both single pin and 7-pin models based on LFR materials and geometry. The study finds that the use of too large a time step size in the heat conduction module can lead to temperature oscillation even though the heat conduction equation does not have a time-derivative kernel, but only the time-dependent boundary condition. A 7-pin model without duct region achieved good convergence in the coupled calculation while a 7 pin model with duct region experienced data communication issues which need to be resolved.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗