A Li 2 S-TiS 2 -Electrolyte Composite for Stable Li 2 S-Based Lithium–Sulfur Batteries
Not provided.
Chemistry↗
SEARCH · Search NASA
Results for “Diffusion process”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Material requirements for the adoption of unconventional silicon crystal and wafer growth techniques for high-efficiency solar cells
Silicon wafers comprise approximately 40% of crystalline silicon module cost and represent an area of great technological innovation potential. Paradoxically, unconventional wafer-growth techniques have thus far failed to displace multicrystalline and Czochralski silicon, despite four decades of innovation. One of the shortcomings of most unconventional materials has been a persistent carrier lifetime deficit in comparison to established wafer technologies, which limits the device efficiency potential. In this perspective article, we review a defect-management framework that has proven successful in enabling millisecond lifetimes in kerfless and cast materials. Control of dislocations and slowly diffusing metal point defects during growth, coupled to effective control of fast-diffusing species during cell processing, is critical to enable high cell efficiencies. As a result, to accelerate the pace of novel wafer development, we discuss approaches to rapidly evaluate the device efficiency potential of unconventional wafers from injection-dependent lifetime measurements.
14 SOLAR ENERGY↗
Ionic Liquid–Directed Nanoporous TiNb 2 O 7 Anodes with Superior Performance for Fast–Rechargeable Lithium–Ion Batteries
Nanoporous TiNb 2 O 7 (NPTNO) material is synthesized by a sol–gel method with an ionic liquid (IL) as the nanoporous structure directing template. NPTNO exhibits a high reversible capacity of 210 mAh g –1 even at the charging rate of 50 C and an excellent cyclability of half-cell capacity retention of 74% for 1000 cycles at 5 C and LiNi 0.5 Mn 1.5 O 4 -coupled full-cell capacity retentions of 81% and 87% for 1000 cycles at 1 C and 2 C, respectively. The studies of the 1000 cycled NPTNO electrode illustrate that the IL-directed mesoporous structure can enhance the cyclability of NPTNO cells due to the alleviation of repetitive mechanical stress and volume fluctuation induced by the repetitive Li + insertion-extraction processes. The measured Li + diffusion coefficients from the galvanostatic intermittent titration technique suggest that the IL-templating strategy indeed ensures the fast rechargeability of NPTNO cells based on the fast Li + diffusion kinetics. Benefitting from the nanoporous structure, NPTNO with unhindered Li + diffusion pathways achieves a superior rate capability in the titanium-based oxide materials and the best full-cell cyclability in the TNO materials. Furthermore, the templating potential of IL is demonstrated, and the superb electrochemical performance establishes the IL-directed NPTNO as a promising anode candidate for fast-rechargeable LIBs.
25 ENERGY STORAGE↗
Electrolyte Gated Oxides
Electrolyte gating has the potential to generate electric fields at the surface of materials in the 10 7 -10 8 V/cm range and induce charge carriers in these materials up to 10 14 -10 15 cm -2 , making this technique very attractive for studying complex and functional oxides. Several types of processes — notably including proton diffusion and intake — can occur during charging, which makes it crucially important to consider and understand exactly how a given material is interacting with an electrolyte. We report on several of these mechanisms and how to distinguish between them.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Titanium Extraction from Spent Selective Catalytic Reduction Catalysts in a NaOH Molten-Salt System: Thermodynamic, Experimental, and Kinetic Studies
In this study, sodium hydroxide was used as an alkali reagent in roasting spent selective catalytic reduction (SCR) catalysts for titanium extraction. The thermodynamic analysis of the roasting process is discussed in terms of process design. The effects of various roasting parameters, such as the mass ratio of NaOH-to-SCR, temperature, and time, on the extraction efficiency of titanium were investigated; under the optimum parameters of 1.8:1, 550 °C, and 10 minutes, the titanium extraction yield reached 97.8 pct. The roasting kinetics of titanium extraction were also studied. The kinetics of titanium extraction follow the Avrami model, which is expressed as follows: −ln(1−x)=K{sub 0}C{sub m{sub N{sub a{sub O{sub H/m{sub S{sub C{sub R}{sup −2.012}}}}}}}}exp(−(4120/(8.314T)))t, and the overall roasting process is controlled by diffusion in the solid state, with an activation energy (E{sub a}) of 4.12 kJ/mol.
36 MATERIALS SCIENCE↗
Examination of Dendritic Growth During Solidification of Ternary Alloys via a Novel Quantitative 3D Cellular Automaton Model
A three-dimensional (3D) quantitative cellular automaton (CA) model was developed to simulate dendritic growth during solidification processing of ternary alloys. A detailed method was proposed to solve solute diffusion and calculate the solid fraction for ternary alloys during solidification. The present model has been shown to accurately predict dendrite morphologies and solute distributions of both single equiaxed dendrite and columnar dendrites during solidification. The model was also used to study the influence of the concentration of a third component (Mg in the Al-Si-Mg system) on dendritic growth. With increasing Mg concentration, the steady-state dendrite tip growth velocity was shown to decrease, resulting in a shorter primary dendrite length. The 3D CA simulation results agree well with the prediction of the LGK theoretical model. Multi-columnar dendrite growth was simulated with different cooling rates. Primary and secondary dendrite morphology was shown to have little variation at low cooling rates (1.0 to 2.0 K/s) and a constant undercooling. The average secondary dendrite arm spacing was shown to decrease with the increase of cooling rate within this range. The 3D CA simulation results are in good agreement with the experimental directional solidification experiments of a commercial A356 (Al-7 wt pct Si-0.3 wt pct Mg).
36 MATERIALS SCIENCE↗
Achieving Metallurgical Bonding in Aluminum/Steel Bimetallic Castings
Abstract Aluminum castings are increasingly being used in automotive powertrain and structural applications for vehicle lightweighting. Cast aluminum parts often need to be machined and joined to steel components in multi-material systems. Bimetallic components produced by casting aluminum over steel substrate are advantageous due to the elimination of machining and traditional dissimilar material joining processes. However, forming a strong metallurgical bonding during overcasting process has been challenging. In this paper, the effects of processing conditions such as substrate surface preparation, pre-heating temperature, melt conditions as well as casting design were studied by investigating the bimetallic interfaces for aluminum A319 casting alloy and a high alloy steel substrate in a sand-casting process. Zn and Al-based substrate coatings were evaluated. The experimental results suggest a metallurgical bond between aluminum and steel can be formed during the sand-casting process via high temperature diffusion with or without coatings. Al-based substrate coating prior to overcasting results in the formation of a continuous layer of intermetallics at the bimetallic interface, with large Al–Si–Fe intermetallics penetrating the cast aluminum.
Moodispaw, Michael P. (ORCID:0000000267635882)↗
Binding and leaching of trace elements in Portland cement pastes
Portland cement contains trace elements originating from the raw materials and the fuels used for cement production. The trace elements are bound to some extent during cement hydration. A small fraction remains dissolved in the pore solution. The dissolved fractions of antimony, barium, chromium, lead, molybdenum and vanadium were quantified in the course of hydration of four different Portland cements. The development of heavy metal concentrations signifies the relevant hydration products for the binding of heavy metals. For chromate and molybdate a substitution for sulfate in ettringite was found. Vanadium and antimony are most likely not bound in ettringite. Barium precipitates as barium sulfate. For lead no clear trends could be observed. Leaching experiments were carried out and the concentrations of the leachates were compared to pore solution concentrations to check if the solubility of the heavy metals is relevant or if the leaching process is controlled by diffusion.
36 MATERIALS SCIENCE↗
An effective numerical algorithm for intra-granular fission gas release during non-equilibrium trapping and resolution
Both fission gas release and gaseous swelling in nuclear fuel are driven by the transport of fission gas from within the fuel grains to grain boundaries (intra-granular fission gas release). The process involves gas atom diffusion in conjunction with trapping in and resolution from intra-granular bubbles, and is described mathematically by a system of two partial differential equations (PDE). Following Speight, under the assumption of equilibrium between trapping and resolution (quasi-stationary approximation) the system can be reduced to a single diffusion equation with an effective diffusion coefficient. Numerical solutions used in engineering fuel performance calculations invariably rely on this simplification. First, we investigate the validity of the quasi-stationary approximation compared to the solution of the general system of PDEs. Results demonstrate that the approximation is valid under most conditions of practical interest, but is inadequate to model intra-granular fission gas release during rapid transients to relatively high temperatures such as postulated reactivity initiated accidents (RIA). Then, we develop a novel numerical algorithm for the solution of the general problem in time-varying conditions. We verify the PolyPole-2 algorithm against a reference finite difference solution for a large number of randomly generated operation histories including prototypical RIA transients. Results demonstrate that PolyPole-2 captures the solution of the general PDE system with a high accuracy and a low computational cost. As a result, the PolyPole-2 algorithm overcomes the quasi-stationary approximation and the concept of an effective diffusion coefficient for the solution of the intra-granular fission gas release problem in nuclear fuel analysis.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
The Instability of Monolayer-Thick PbSe on VSe 2
Two-dimensional monolayers derived from 3D bulk structures remain a relatively unexplored class of materials because of the challenge of stabilizing non-epitaxial interfaces. Here, we report an unusual reconstruction during the deposition of precursors when targeting the synthesis of heterostructures with an odd number of PbSe monolayers. Multilayer elemental precursors of Pb|Se + V|Se were deposited to have correct number of atoms to form [(PbSe) 1+δ ] q (VSe 2 ) 1 where q is the number of PbSe monolayers in the heterostructure. Structural analysis of the self-assembled precursor via xray reflectivity, x-ray diffraction, and HAADF-STEM suggests three different behaviors upon deposition. Precursors with q 7 and even values of q have the targeted nanoarchitectures after deposition which are maintained as the products are selfassembled through a near diffusionless process. Significant lateral surface diffusion occurred during deposition of precursors with q = 1, 3, and 5 resulting in the precursor having a different nanoarchitecture than targeted. Additional perpendicular long range diffusion occurs during self-assembly of these precursors resulting in different final products than targeted. DFT calculations of PbSe blocks show that the odd numbered layers are less stable than even numbered layers, which suggests an energetic driving force for the observed rearrangement. This work highlights the importance of understanding the reaction mechanism when attempting to prepare 2D layers of constituents with bulk 3D structures.
36 MATERIALS SCIENCE↗
Building Materials from Colloidal Nanocrystal Assemblies: Molecular Control of Solid/Solid Interfaces in Nanostructured Tetragonal ZrO 2
We describe in this paper a bottom-up approach to control the composition of solid/solid interfaces in nanostructured materials, and we test its effectiveness on tetragonal ZrO 2 , an inorganic phase of great technological significance. Colloidal nanocrystals capped with trioctylphosphine oxide (TOPO) or oleic acid (OA) are deposited, and the organic fraction of the ligands is selectively etched with O 2 plasma. The interfaces in the resulting all-inorganic colloidal nanocrystal assemblies are either nearly bare (for OA-capped nanocrystals) or terminated with phosphate groups (for TOPO-capped nanocrystals) resulting from the reaction of phosphine oxide groups with plasma species. The chemical modification of the interfaces has extensive effects on the thermodynamics and kinetics of the material. Different growth kinetics indicate different rate limiting processes of growth (surface diffusion for the phosphate-terminated surfaces and dissolution for the “bare” surfaces). Phosphate termination led to a higher activation energy of growth, and a 3-fold reduction in interfacial energy, and facilitated significantly the conversion of the tetragonal phase into the monoclinic phase. Finally, films devoid of residual ligands persisted in the tetragonal phase at temperatures as high as 900 °C for 24 h.
36 MATERIALS SCIENCE↗
Heterolytic Scission of Hydrogen Within a Crystalline Frustrated Lewis Pair
We report the heterolysis of molecular hydrogen under ambient conditions by the crystalline frustrated Lewis pair (FLP) 1-{2-[bis(pentafluorophenyl)boryl]phenyl}-2,2,6,6-tetramethylpiperidine (KCAT). The gas–solid reaction provides an approach to prepare the solvent-free, polycrystalline ion pair KCATH2 through a single crystal to single crystal transformation. The crystal lattice of KCATH2 increases in size relative to the parent KCAT by approximately 2%. Microscopy was used to follow the transformation of the highly colored red/orange KCAT to the colorless KCATH2 over a period of 2 h at 300 K under a flow of H2 gas. There is no evidence of crystal decrepitation during hydrogen uptake. Inelastic neutron scattering employed over a temperature range from 4–200 K did not provide evidence for the formation of polarized H2 in a precursor complex within the crystal at low temperatures and high pressures. However, at 300 K, the INS spectrum of KCAT transformed to the INS spectrum of KCATH2. Calculations suggest that the driving force is more favorable in the solid state compared to the solution or gas phase, but the addition of H2 into the KCAT crystal is unfavorable. Ab Initio methods were used to calculate the INS spectra of KCAT, KCATH2, and a possible precursor complex of H2 in the pocket between the B and N of crystalline KCAT. Ex-situ NMR showed that the transformation from KCAT to KCATH2 is quantitative and our results suggest that the hydrogen heterolysis process occurs via H2 diffusion into the FLP crystal with a rate-limiting movement of H2 from inactive positions to reactive sites.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Pinned Electrode/Electrolyte Interphase and Its Formation Origin for Sulfurized Polyacrylonitrile Cathode in Stable Lithium Batteries
Sulfurized polyacrylonitrile (SPAN) represents one of the most promising directions for high-energy-density lithium (Li)-sulfur batteries. However, the practical application of Li||SPAN is currently limited by the insufficient chemical/electrochemical stability of electrode/electrolyte interphase (EEI). Here, a pinned EEI layer is designed for stabilizing a SPAN cathode by regulating the EEI formation mechanism in an advanced LiFSI/ether/fluorinated-ether electrolyte. Computational simulations and experimental investigations reveal that, benefiting from the nonsolvating nature, the fluorinated-ether can not only act as a protective shield to prevent the Li polysulfides dissolution but also, more importantly, endow a diffusion-controlled EEI formation process. It promotes the formation of a uniform, protective, and conductive EEI layer pinning into SPAN surface region, enabling the high loading Li||SPAN batteries with superior cycling stability, wide temperature performance, and high-rate capability. Finally, this design strategy opens an avenue for exploring advanced electrolytes for Li||SPAN batteries and guides the interface design for broad types of battery systems.
25 ENERGY STORAGE↗
Porous Structured Ni–Fe–P Nanocubes Derived from a Prussian Blue Analogue as an Electrocatalyst for Efficient Overall Water Splitting
Exploring nonprecious metal electrocatalysts to replace the noble metal-based catalysts for full water electrocatalysis is still an ongoing challenge. In this work, porous structured ternary nickel–iron–phosphide (Ni–Fe–P) nanocubes were synthesized through one-step phosphidation of a Ni–Fe-based Prussian blue analogue. The Ni–Fe–P nanocubes exhibit a rough and loose porous structure on their surface under suitable phosphating temperature, which is favorable for the mass transfer and oxygen diffusion during the electrocatalysis process. As a result, Ni–Fe–P obtained at 350 °C with poorer crystallinity offers more unsaturated atoms as active sites to expedite the absorption of reactants. Additionally, the introduction of nickel improved the electronic structure and then reduced the charge-transfer resistance, which would result in a faster electron transport and an enhancement of the intrinsic electrocatalytic activities. Benefiting from the unique porous nanocubes and the chemical composition, the Ni–Fe–P nanocubes exhibit excellent hydrogen evolution reaction and oxygen evolution reaction activities in alkaline medium, with low overpotentials of 182 and 271 mV for delivering a current density of 10 mA cm–2, respectively. Moreover, the Ni–Fe–P nanocubes show outstanding stability for sustained water splitting in the two-electrode alkaline electrolyzer. Furthermore, this work not only provides a facile approach for designing bifunctional electrocatalysts but also further extends the application of metal–organic frameworks in overall water splitting.
36 MATERIALS SCIENCE↗
Strain wave pathway to semiconductor-to-metal transition revealed by time-resolved X-ray powder diffraction
One of the main challenges in ultrafast material science is to trigger phase transitions with short pulses of light. Here we show how strain waves, launched by electronic and structural precursor phenomena, determine a coherent macroscopic transformation pathway for the semiconducting-to-metal transition in bistable Ti 3 O 5 nanocrystals. Employing femtosecond powder X-ray diffraction, we measure the lattice deformation in the phase transition as a function of time. We monitor the early intra-cell distortion around the light absorbing metal dimer and the long range deformations governed by acoustic waves propagating from the laser-exposed Ti 3 O 5 surface. We developed a simplified elastic model demonstrating that picosecond switching in nanocrystals happens concomitantly with the propagating acoustic wavefront, several decades faster than thermal processes governed by heat diffusion.
36 MATERIALS SCIENCE↗
Numerical simulation of temperature field, microstructure evolution and mechanical properties of HSS during hot stamping
The hot stamping of boron steels is widely used to produce ultra high strength automobile components without any spring back. The ultra high strength of final products is attributed to the fully martensitic microstructure that is obtained through the simultaneous forming and quenching of the hot blanks after austenization. In the present study, a mathematical model incorporating both heat transfer and the transformation of austenite is presented. A FORTRAN program based on finite element technique has been developed which permits the temperature distribution and microstructure evolution of high strength steel during hot stamping process. Two empirical diffusion-dependent transformation models under isothermal conditions were employed respectively, and the prediction capability on mechanical properties of the models were compared with the hot stamping experiment of an automobile B-pillar part.
36 MATERIALS SCIENCE↗