Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dynamic profiling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Studies on chemoviscosity modeling for thermosetting resins

A new analytical model for simulating chemoviscosity of thermosetting resins has been formulated. The model is developed by modifying the well-established Williams-Landel-Ferry (WLF) theory in polymer rheology for thermoplastic materials. By introducing a relationship between the glass transition temperature Tg(t) and the degree of cure alpha(t) of the resin system under cure, the WLF theory can be modified to account for the factor of reaction time. Temperature dependent functions of the modified WLF theory constants C sub 1 (t) and C sub 2 (t) were determined from the isothermal cure data. Theoretical predictions of the model for the resin under dynamic heating cure cycles were shown to compare favorably with the experimental data. This work represents progress toward establishing a chemoviscosity model which is capable of not only describing viscosity profiles accurately under various cure cycles, but also correlating viscosity data to the changes of physical properties associated with the structural transformation of the thermosetting resin systems during cure.

Bai, J. M.↗

Gravity waves and convection in Colorado during July 1983

The dynamics of gravity-wave/convective-cell interaction is studied using NOAA data collected in NE Colorado during July and August 1983. The pressure fields measured with microbarographs, the tropospheric wind profiles obtained with a UHF wind profiler radar, and precipitation data collected with a 10-cm weather radar for four events (A, B, C, and D) are analyzed. The four disturbances are detected through a substantial depth of the troposphere. It is observed that in event A the wave and convective cells appear to be locked together; in event B, the wave and convective cells commence about the same time, but the wave velocities differ from the cell velocities; and in events C and D, the waves move faster than the maximum wind in the jet and faster than the convective cells. It is suggested that events A and B are generated by wind shear in the jet stream, and the excitation of events C and D depends on mechanisms such as vertical convective motion and acceleration in the jet flow.

Einaudi, F.↗

Large-scale motions on the sun - An overview

The history and present status of observations of large-scale velocity fields in the solar atmosphere are reviewed. Observations of the torsional oscillation and of mean meridional circulation suggest a connection of large-scale dynamics with the solar cycle. Significant problems must be solved before Doppler observations can match the precision of tracer measurements, particularly allowing for the effects of changes in line-profile asymmetries and for scattered light. Coordinated observations would establish the reliability of Doppler techniques, but Doppler measurements with precision of order 1 m/s made in a proper spatial-temporal window appear necessary for the identification of sub-global velocity fields varying with time-scales less than that of the solar cycle.

Bogart, Richard S.↗

Wind Measurements from 15 to 50 Km with a Doppler Rayleigh Lidar

The possibility to measure the mean wind in the high stratosphere using a Doppler Rayleigh lidar was demonstrated in 1989, and the Observatory of Haute Province (44 deg N, 6 deg E). It was originally developed to cover the height range 25-60 km, a region where the radars cannot operate; therefore, the system was designed to cover altitudes where the signal is only due to the Rayleigh backscattering. The instrument is currently set up at the Center d'Essais des Landes (44 deg N, 1 deg W) where it operated during the Dynamic Adapted Network for the Atmosphere Campaign in 1990. As the contribution of the Mie scattering was very low during this period above southern France, we have obtained vertical wind profiles in the stratosphere down to 15 km. Since the eruption of the Pinatubo volcano in Jun. 1991, the contribution of Mie scattering has increased between 15 and 30 km and it was very difficult with the original system to obtain wind measurements below 30 km. We will show that by using the same method with slightly different characteristics of the system, it is possible to measure the wind in the presence of Mie scattering. The first experimental results are presented.

Garnier, A.↗

Spacecraft Radio Scintillation and Solar System Exploration

When a wave propagates through a turbulent medium, scattering by the random refractive index inhomogeneities can lead to a wide variety of phenomena that have been the subject of extensive study. The observed scattering effects include amplitude or intensity scintillation, phase scintillation, angular broadening, and spectral broadening, among others. In this paper, I will refer to these scattering effects collectively as scintillation. Although the most familiar example is probably the twinkling of stars (light wave intensity scintillation by turbulence in the Earth's atmosphere), scintillation has been encountered and investigated in such diverse fields as ionospheric physics, oceanography, radio astronomy, and radio and optical communications. Ever since planetary spacecraft began exploring the solar system, scintillation has appeared during the propagation of spacecraft radio signals through planetary atmospheres, planetary ionospheres, and the solar wind. Early studies of these phenomena were motivated by the potential adverse effects on communications and navigation, and on experiments that use the radio link to conduct scientific investigations. Examples of the latter are radio occultation measurements (described below) of planetary atmospheres to deduce temperature profiles, and the search for gravitational waves. However,these concerns soon gave way to the emergence of spacecraft radio scintillation as a new scientific tool for exploring small-scale dynamics in planetary atmospheres and structure in the solar wind, complementing in situ and other remote sensing spacecraft measurements, as well as scintillation measurements using natural (celestial) radio sources. The purpose of this paper is to briefly describe and review the solar system spacecraft radio scintillation observations, to summarize the salient features of wave propagation analyses employed in interpreting them, to underscore the unique remote sensing capabilities and scientific relevance of the scintillation measurements, and to highlight some of the scientific results obtained to date. Special emphasis is placed on comparing the remote sensing features of planetary and terrestrial scintillation measurements, and on contrasting spacecraft and natural radio source scintillation measurements. I will first discuss planetary atmospheres and ionospheres, and then the solar wind.

Woo, Richard↗

A Status Report on the SHADOZ (Southern Hemisphere Additional Ozonesondes) Project and Some Issues Affecting Ozone Climatology

SHADOZ aims to support the study of local and global patterns in stratospheric and tropospheric ozone and to provide a data set for the validation for satellite products and model calculations of ozone. Southern hemispheric tropical ozone is of particular interest because this region appears to have complex interplay among photochemical ozone formation (from biomass burning and lightning), stratospheric dynamics, convection and possibly cross-hemispheric transport. Balloon-borne ozone instrumentation (ozonesondes), joined with standard radiosondes for measurement of pressure, temperature and relative humidity, is used to collect profiles throughout the troposphere and lower- to mid-stratosphere. A network of 10 southern hemisphere tropical and subtropical stations, called the Southern Hemisphere ADditional OZonesondes (SHADOZ) project, has been established from operational sites to assemble sonde data for 1998-2000. A status report on the archive, with station operating characteristics, will be given, along with some operational issues that may affect data analysis and interpretation.

Thompson, Anne M.↗

Non-Linear Structural Dynamics Characterization using a Scanning Laser Vibrometer

This paper presents the use of a scanning laser vibrometer and a signal decomposition method to characterize non-linear dynamics of highly flexible structures. A Polytec PI PSV-200 scanning laser vibrometer is used to measure transverse velocities of points on a structure subjected to a harmonic excitation. Velocity profiles at different times are constructed using the measured velocities, and then each velocity profile is decomposed using the first four linear mode shapes and a least-squares curve-fitting method. From the variations of the obtained modal \ielocities with time we search for possible non-linear phenomena. A cantilevered titanium alloy beam subjected to harmonic base-excitations around the second. third, and fourth natural frequencies are examined in detail. Influences of the fixture mass. gravity. mass centers of mode shapes. and non-linearities are evaluated. Geometrically exact equations governing the planar, harmonic large-amplitude vibrations of beams are solved for operational deflection shapes using the multiple shooting method. Experimental results show the existence of 1:3 and 1:2:3 external and internal resonances. energy transfer from high-frequency modes to the first mode. and amplitude- and phase- modulation among several modes. Moreover, the existence of non-linear normal modes is found to be questionable.

Pai, P. F.↗

Analysis of Probe Surveys Conducted in the 10-MW TP3 Arc-Jet Facility 15-Inch Nozzle Flow

Computational simulations and analysis of flow characterization tests in a high enthalpy arc-jet facility at NASA Ames Research Center are reported. These tests were conducted in the 10-MW TP3 facility 15-inch conical nozzle, and pitot pressure and heat flux probes are used to survey test flow downstream of the nozzle exit. Two 1.59-cm (0.625 in) diameter hemisphere probes were used: one with a stagnation-point pressure port, the other with a Gardon heat flux gage. Calibration data were also obtained using 10.16-cm iso-q and 20.32-cm flat-faced slug calorimeters. Experimental surveys of arc-jet test flow with pitot pressure and heat flux probes were obtained at eight arc-heater conditions, covering wide ranges in arc current (316–1756 A) and mass flow rate (32–500 g/s, without any cold-gas injection at the arc-heater plenum) and providing assessment of the flow uniformity in the facility. The present analysis comprises computational fluid dynamics simulations of the nonequilibrium flowfield in the facility nozzle and test box, including the models tested. These simulations take into account non-uniform total enthalpy and mass flux profiles at the nozzle inlet as well as the expansion waves emanating from the nozzle exit and their effects on the model flowfields. Comparisons of computations with the experimental measurements are presented, showing reasonably good agreement. The probe survey data and accompanying analysis show that the test flow in the TP3 15-inch nozzle is highly non-uniform at most conditions, and the extent of flow non-uniformity depends on arc current and mass flow rate.

Arc-jets↗

Analysis of Probe Surveys Conducted in the 10-MW TP3 Arc-Jet Facility 15-Inch Nozzle Flow

Computational simulations and analysis of flow characterization tests in a high enthalpy arc-jet facility at NASA Ames Research Center are reported. These tests were conducted in the 10-MW TP3 facility 15-inch conical nozzle, and pitot pressure and heat flux probes are used to survey test flow downstream of the nozzle exit. Two 1.59-cm (0.625 in) diameter hemisphere probes were used: one with a stagnation-point pressure port, the other with a Gardon heat flux gage. Calibration data were also obtained using 20.32-cm flat-faced slug calorimeters. Experimental surveys of arc-jet test flow with pitot pressure and heat flux probes were obtained at eight arc-heater conditions, covering wide ranges in arc current (316–1756 A) and mass flow rate (32–500 g/s, without any cold-gas injection at the arc-heater plenum) and providing assessment of the flow uniformity in the facility. The present analysis comprises computational fluid dynamics simulations of the nonequilibrium flowfield in the facility nozzle and test box, including the models tested. These simulations take into account non-uniform total enthalpy and mass flux profiles at the nozzle inlet as well as the expansion waves emanating from the nozzle exit and their effects on the model flowfields. Comparisons of computations with the experimental measurements are presented, showing reasonably good agreement. The probe survey data and accompanying analysis show that the test flow in the TP3 15-inch nozzle is highly non-uniform at most conditions, and the extent of flow non-uniformity depends on arc current and mass flow rate.

Arc-jets↗

Using Importance Sampling Monte Carlo to Analyze Aircraft Takeoff and Landing

Aircraft have achieved high levels of reliability, so the probability of undesirable dynamics is very low. The low probability of a bad takeoff or landing challenges nondeterministic methods to quantify the uncertainty of these improbable events. In the present work, a Monte Carlo method is defined to more effectively quantify these unlikely events that is suitable for uncertainty analysis of a mature design with many uncertainty parameters. The proposed Monte Carlo method has been applied to the takeoff and landing of the X-59 Quiet SuperSonic Technology (QueSST). Takeoff and landing simulation profiles were defined using a combination of industry standards and piloted simulation experience. The proposed method is shown to be able to quantify events with significantly fewer samples than would be required with conventional Monte Carlo. These results improve understanding of the sensitivity of the takeoff and landing dynamics to inform further studies and test planning.

Jeffrey Ouellette↗

Using Importance Sampling Monte Carlo to Analyze Aircraft Takeoff and Landing

Aircraft have achieved high levels of reliability, so the probability of undesirable dynamics is very low. The low probability of a bad takeoff or landing challenges nondeterministic methods to quantify the uncertainty of these improbable events. In the present work, a Monte Carlo method is defined to more effectively quantify these unlikely events that is suitable for uncertainty analysis of a mature design with many uncertainty parameters. The proposed Monte Carlo method has been applied to the takeoff and landing of the X-59 Quiet SuperSonic Technology (QueSST). Takeoff and landing simulation profiles were defined using a combination of industry standards and piloted simulation experience. The proposed method is shown to be able to quantify events with significantly fewer samples than would be required with conventional Monte Carlo. These results improve understanding of the sensitivity of the takeoff and landing dynamics to inform further studies and test planning.

Jeffrey Ouellette↗

Oceanographic mapping of structure and dynamics of the northern Gulf of California by the use of spectral modeling and ERTS-1

Distribution and flow of water masses at four depth intervals were determined by analyzing ERTS imagery through the use of optical models of classes of vertical oceanographic profiles. Data used for these models was obtained from shipboard measurements including surface spectral radiance, and optical and more conventional oceanographic depth profiles. The spectral models obtained were applied to radiance-contoured ERTS imagery in band 4, 5, 6, and 7. Features mapped by direct photointerpretation of ERTS imagery include submerged shoals, current streamlines, and location of possible upwellings, downwellings and submarine springs.

Lepley, L. K.↗

Radiative accretion of intracluster gas onto dominant galaxies in poor clusters

An analysis of X-ray images of MKW 4, MKW 3, AMW 4, and AMW 7 indicates that the hot gas in poor clusters is cooling and accreting onto the central, dominant galaxies. The deprojection technique of Fabian et al (1980) is applied to deduce the detailed density and temperature profiles for a wide range of assumed parameters. For each cluster, the mass accretion rates computed vary by less than a factor of 2 over the full range of the assumed parameters. Examinations of the gas and light density profiles, and of the effects of contraction of the gravitational potential, lead to the conclusion that the high gas densities giving rise to cooling flows are not primarily the result of dynamical evolution of the cluster, especially the merger of galaxies to form the dominant galaxy. Instead, the general initial condition of high material density favors both mergers and cooling flows.

Stewart, G. C.↗

Gravity Waves

In recent years it has been widely recognized that vertically propagating gravity waves play an important role in the dynamics of the middle atmosphere in partly determining the large scale temperature and wind structure through their energy and momentum transport. In particular, the meridional temperature distribution and the mean wind profile in the upper mesosphere are considered to be largely affected by the turbulence diffusion and friction that gravity waves induce through their breaking. For an understanding of the middle atmosphere circulation, it is therefore very important to know the global distribution and temporal variation of gravity waves in a climatological sense. The results of the statistics for gravity wave activity in the stratosphere and mesosphere are presented as a function of latitude and month, with the aid of meteorological rocket network observations.

Hirota, I.↗

Chemoviscosity modeling for thermosetting resin systems, part 3

A new analytical model for simulating chemoviscosity resin has been formulated. The model is developed by modifying the well established Williams-Landel-Ferry (WLF) theory in polymer rheology for thermoplastic materials. By introducing a relationship between the glass transition temperature (T sub g (t)) and the degree of cure alpha(t) of the resin system under cure, the WLF theory can be modified to account for the factor of reaction time. Temperature-dependent functions of the modified WLF theory parameters C sub 1 (T) and C sub 2 (T) were determined from the isothermal cure data. Theoretical predictions of the model for the resin under dynamic heating cure cycles were shown to compare favorably with the experimental data. This work represents a progress toward establishing a chemoviscosity model which is capable of not only describing viscosity profiles accurately under various cure cycles, but also correlating viscosity data to the changes of physical properties associated with the structural transformations of the thermosetting resin systems during cure.

Hou, T. H.↗

Preliminary statistical survey of plasmaspheric ion properties from observations by DE 1/RIMS

The paper presents mean temperatures and densities of plasmaspheric H(+) ions obtained from observations by the retarding ion mass spectrometer on Dynamics Explorer 1. Composition is shown in terms of ratios of densities of the various ion species to those of H(+). The spatial variations are indicated in terms of L shell profiles, with separate profiles for local morning and evening sides.

Comfort, R. H.↗

A real-time algorithm for integrating differential satellite and inertial navigation information during helicopter approach

A real-time, high-rate precision navigation Kalman filter algorithm is developed and analyzed. This Navigation algorithm blends various navigation data collected during terminal area approach of an instrumented helicopter. Navigation data collected include helicopter position and velocity from a global position system in differential mode (DGPS) as well as helicopter velocity and attitude from an inertial navigation system (INS). The goal of the Navigation algorithm is to increase the DGPS accuracy while producing navigational data at the 64 Hertz INS update rate. It is important to note that while the data was post flight processed, the Navigation algorithm was designed for real-time analysis. The design of the Navigation algorithm resulted in a nine-state Kalman filter. The Kalman filter's state matrix contains position, velocity, and velocity bias components. The filter updates positional readings with DGPS position, INS velocity, and velocity bias information. In addition, the filter incorporates a sporadic data rejection scheme. This relatively simple model met and exceeded the ten meter absolute positional requirement. The Navigation algorithm results were compared with truth data derived from a laser tracker. The helicopter flight profile included terminal glideslope angles of 3, 6, and 9 degrees. Two flight segments extracted during each terminal approach were used to evaluate the Navigation algorithm. The first segment recorded small dynamic maneuver in the lateral plane while motion in the vertical plane was recorded by the second segment. The longitudinal, lateral, and vertical averaged positional accuracies for all three glideslope approaches are as follows (mean plus or minus two standard deviations in meters): longitudinal (-0.03 plus or minus 1.41), lateral (-1.29 plus or minus 2.36), and vertical (-0.76 plus or minus 2.05).

Hoang, TY↗