Search NASA⌕ Search

SEARCH · Search NASA

Results for “Excel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Hot-Tearing Assessment of Multicomponent Nongrain-Refined Al-Cu Alloys for Permanent Mold Castings Based on Load Measurements in a Constrained Mold

The hot-tearing resistance of multicomponent Al-Cu alloys during permanent mold casting was investigated using a constrained permanent mold in which the load and temperature were measured. The nominal Cu composition was varied from 5 to 8 wt pct. Casting experiments were conducted without adding any grain-refining inoculants. The following variables, which were obtained from the measured load data during casting, were considered to assess the hot-tearing resistance of the Al-Cu multicomponent alloys: “V”-like signature in the load rate variation, load at solidus point, and load rate average over the freezing range. In addition, a hot-tearing criterion based on the variation of the fraction of solid in the late stages of solidification was used. It was found that all criteria considered can accurately predict the alloys with the lowest and highest hot-tear resistance, respectively. It was found that the rate of measured load during casting could be used to indicate substantial hot tearing. However, the load rate variation could not be used to detect when small hot tears were present. Among all the criteria considered, the load at the solidus point shows an excellent agreement with experimentally observed hot-tearing resistance for all but one alloy. The poorly resistant hot-tearing alloys exhibited mainly coarse columnar grains while the most hot-tearing resistant alloys exhibited a much more refined grain microstructure. This is the first study in which good hot-tear resistance is demonstrated for multicomponent Al-Cu alloys with nominal Cu content greater than 7 wt pct.

36 MATERIALS SCIENCE↗

The Sliding Wear and Frictional Behavior of M50-10 wt.%(Sn-Ag-Cu) Self-Lubricating Materials at Elevated Temperatures

As the main steel used in the aero-engine main shaft bearings, the tribological properties of M50 can directly affect the performance of aero-engine. The purpose of this study is to design the reasonable composition of Sn-Ag-Cu alloy and investigate the wear mechanisms of M50-10 wt.%(Sn-Ag-Cu) composites (MSACC) prepared by SPS sliding against Si{sub 3}N{sub 4} ball from 25 to 550 °C at 12 N-0.25 m/s. XRD, EPMA, FESEM and EDS mappings are conducted to understand the major mechanisms leading to the improvement in the sliding behavior of MSACC. The results indicate that MSACC with different specifications of Sn-Ag-Cu alloy shows excellent friction and wear properties from 25 to 550 °C compared to M50. M50-10 wt.%(50Sn40Ag10Cu) (MSACC-2) shows the distinguished tribological performance for the lower friction coefficients of 0.22-0.61 and less wear rates of 1.7-4.1 × 10{sup −6} mm{sup 3} N{sup −1} m{sup −1}, which is attributed to the formed excellent lubricating structure consisting of the lubricating film with massive Sn-Ag-Cu alloy and intermetallic compounds formed during the friction process, as well as the underneath mixed layer who can well support the lubricating film due to the good intersolubility between the designed Sn-Ag-Cu alloy and M50 (Fe).

36 MATERIALS SCIENCE↗

The Application of Canned Deformation to a Hard-Deformed Spray-Deposited Al-Zn-Mg-Cu Alloy

A wide variety of industrial applications require Al-Zn-Mg-Cu alloys with high strength and ductility. However, Zn-rich Al-Zn-Mg-Cu alloys prepared by rapid solidification methods usually show excellent strength but poor formability, which restricts their wide application in complex forming. In this study, we developed a new deformation method for the spray-deposited Zn-rich Al-Zn-Mg-Cu alloy to avoid crack formation and achieve isotropic properties. The microstructure evolution and crystallographic textures were analyzed and compared with the results of a normal deformation process. Crack-free forgings with the ultimate tensile strength (UTS), yield strength (YS) and elongation of 727 ± 5 MPa, 690 ± 3 MPa, 5.0 ± 0.7% along the radial direction and 735 ± 2 MPa, 693 ± 3 MPa, 6.3 ± 0.2% along the tangential direction were finally obtained. The improvement in the mechanical properties can be attributed to the larger amount of subgrains and substructures generated in the canned deformed alloy. The results of this study show excellent advantages and potential application prospects of the canned deformation to hard-deformed Al-Zn-Mg-Cu alloys.

36 MATERIALS SCIENCE↗

Fabrication of Brushite Coating on AZ91D and AZ31 Alloys by Two-Step Chemical Treatment and Its Surface Protection in Simulated Body Fluid

A biocompatible dicalcium phosphate dihydrate (DCPD) brushite coating of flake-like crystals was developed on AZ91D and AZ31 magnesium (Mg) surfaces to control and slow down the rapid degradation rate of the substrates. The electrochemical behavior of the DCPD-coated substrates was examined in a simulated body fluid (SBF) with uncoated substrates as the control. Fabrication of the coating was achieved via chemical immersion technique by modifying the surfaces with Ca(NO{sub 3}){sub 2}·4H{sub 2}O and KH{sub 2}PO{sub 4} in addition to heat treatment. The morphology of the DCPD coating is uniform and dense with a flake-like crystal structure. After in vitro tests, the DCPD coating would have exhibited excellent corrosion resistance with more biomineralization of the active calcium phosphate (CaP). Moreover, the DCPD coating induced CaP formation after immersion in the SBF, indicating excellent bioactivity upon increasing the coating. Hence, the two-step chemical treatment enhances the bioactivity of DCPD coatings on Mg alloys, making them better implant materials.

36 MATERIALS SCIENCE↗

Effects of Particle Characteristic Parameters on the Electrical Conductivity of TiB{sub 2}/Cu Composites: A Modified Model for Predicting Their Electrical Conductivity

High-strength and highly conductive copper matrix composites can not only maintain excellent electrical and thermal conductivity but also enhance the strength and hardness of materials, showing that composites have a bright future for development. Predictions of the effective electrical conductivity of copper matrix composites disagree with experimental data due to the dependence of the composites on several factors. Most prediction models simply consider the influence of the particle volume fraction on conductivity. In the present study, the influence of the volume fraction and the size of the TiB{sub 2} particle on the electrical conductivity of TiB{sub 2}/Cu composites are investigated. The obtained electrical conductivity results correlate with the volume fraction, size, and distribution of particles in a pure copper matrix. A modified model for predicting the electrical conductivity is proposed where the particle spacing parameters are introduced into the existing Maxwell model. The particle spacing parameter, as a fitting parameter, fits the experimental data of the copper matrix composites excellently.

36 MATERIALS SCIENCE↗

Effect of Silver and Carbon Fiber on the Tribological Properties of M50 Matrix Composites Under Different Loads

As one of the most widely used high-performance bearing steels, the service life of M50 steel is closely related to its tribological properties. In this paper, the dry sliding tribological tests of M50 matrix composite containing 5.0 wt.% Ag and 5.0 wt.% carbon fiber (CF) against Si{sub 3}N{sub 4} ceramic balls are carried out under different applied loads. The morphologies and compositions of worn surfaces and the cross sections of worn scars are systematically characterized to explore the wear mechanisms. The results indicate that M50-Ag-CF composites (MAC) exhibit the excellent tribological properties at 10 N, whose friction coefficient and wear rate are 0.212 and 1.6 × 10{sup −6} mm{sup 3} N{sup −1} m{sup −1}, respectively. The excellent tribological performance can be attributed to the synergistic effect of Ag and CF. Massive Ag is enriched on the friction surface to form a lubricating film, thus reducing the surface roughness and friction coefficient. Meanwhile, CF acts as a reinforcement and improves the wear resistance of M50 matrix composites.

36 MATERIALS SCIENCE↗

Oxidation Resistance in 1200°C Steam of a FeCrAl Alloy Fabricated by Three Metallurgical Processes

Abstract FeCrAl alloys are a leading candidate material for accident tolerant fuel cladding due to their good performance in both normal light-water reactor operating conditions as well as their resilience to high-temperature accident scenarios. For commercial-scale production, new fabrication techniques need to be investigated. In this study, the effects of fabrication methods on the high-temperature steam oxidation performance of C26M (Fe12Cr6Al2Mo in wt.%) were investigated. Three variants of C26M were manufactured: wrought (cast and forged) (WC26M), powder metallurgy hot isostatic pressing (PMC26M), and laser powder bed fusion additive manufacturing (AMC26M). All three variants were exposed to steam at 1200°C for 2 h. Results showed no significant variation in mass change between the variants after steam exposure. All three variants effectively formed stable protective alumina films with ~0.6–1.3 µ m thickness. This study suggests FeCrAl alloys have excellent resilience to high-temperature steam in nuclear reactor accident scenarios regardless of the fabrication method.

Materials Science↗

Comparison of CZT SPECT and conventional SPECT for assessment of contractile function, mechanical synchrony and myocardial scar in patients with heart failure

Aim: The aim of this study was to compare CZT-SPECT (CZT SPECT) to conventional SPECT (C-SPECT) in the assessment of left ventricular myocardial scar, contractile function, and mechanical synchrony in patients with heart failure (HF). Methods: Fifty-nine patients with HF who were referred for myocardial perfusion/metabolism imaging were enrolled. All patients underwent resting {sup 99m}Tc-MIBI gated myocardial perfusion imaging using a CZT SPECT camera and a C-SPECT camera, respectively, and {sup 18}F-FDG PET myocardial metabolism imaging within three days. Summed rest score (SRS) and total perfusion defect (TPD) (as indices of perfusion abnormality), left ventricular (LV), end diastolic volume (EDV), end systolic volume (ESV), and ejection fraction (EF) (as indices of LV systolic function), and histogram band width (BW) and standard deviation (SD) (as indices of mechanical synchrony) were analyzed by automated software while the perfusion/metabolism patterns were analyzed visually. Results: There was a good correlation between CZT SPECT and C-SPECT for SRS and TPD. CZT SPECT tended to underestimate SRS and TPD compared to C-SPECT. CZT-SPECT and C-SPECT showed excellent agreement in assessing the perfusion/metabolism pattern though a small proportion of normal segments (6.6%) identified by CZT/PET exhibited mismatch pattern on C-SPECT/PET. CZT SPECT also showed excellent correlation with C-SPECT in measuring EDV, ESV, and EF. Finally, BW and SD measured by CZT SPECT correlated well with C-SPECT but CZT SPECT tended to overestimate BW and SD compared to C-SPECT. Conclusion: CZT SPECT provided comparable data to C-SPECT for measuring LV scar, function and synchrony at a considerable reduction in imaging time. CZT SPECT holds a promise for comprehensive evaluation of myocardial performance in patients with HF.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Evaluation of left ventricular mass on cadmium-zinc-telluride imaging: Validation against cardiac magnetic resonance

Background: Single-photon emission computed tomography has shown relevant limitations in the quantification of left ventricular (LV) mass. We sought to compare the estimates of LV mass on Cadmium-Zinc-Telluride (CZT) myocardial perfusion imaging (MPI) as compared to cardiac magnetic resonance (CMR). Methods and results: Twenty-five patients underwent MPI on a CZT camera and CMR on a 1.5 T scanner within 12 ± 3 weeks. LV mass was quantified on CZT images using two softwares: 4D-MSPECT (4DM) and Emory Cardiac Toolbox (ECTb). LV mass by CMR was quantified using MASS software (Medis, Leiden, The Netherlands). LV mass values obtained with 4DM and ECTb were highly reproducible [intraclass correlation coefficients .98 (95% CI .97-.99), and .98 (95% CI 0.97-.99), respectively]. The mean LVM mass values were 151 ± 44 g on CMR, 151 ± 43 g with 4DM (P = NS vs CMR), and 157 ± 42 g with ECTb (P < .001 vs CMR; P = .007 vs 4DM) CZT images. There was an excellent correlation between LV mass values between CMR and both 4DM (R{sup 2} = .95; P < .001) and ECTb (R{sup 2} = .98; P < .001) with narrow limits of agreement (− 13.6% to + 13.4% for 4DM, and − 5.6% to + 14.1% for ECTb). Conclusions: The evaluation of LV mass is feasible on CZT images, showing excellent agreement with CMR.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

TiO{sub 2} Photocatalyzed Oxidation of Drugs Studied by Laser Ablation Electrospray Ionization Mass Spectrometry

In drug discovery, it is important to identify phase I metabolic modifications as early as possible to screen for inactivation of drugs and/or activation of prodrugs. As the major class of reactions in phase I metabolism is oxidation reactions, oxidation of drugs with TiO{sub 2} photocatalysis can be used as a simple non-biological method to initially eliminate (pro)drug candidates with an undesired phase I oxidation metabolism. Analysis of reaction products is commonly achieved with mass spectrometry coupled to chromatography. However, sample throughput can be substantially increased by eliminating pretreatment steps and exploiting the potential of ambient ionization mass spectrometry (MS). Furthermore, online monitoring of reactions in a time-resolved way would identify sequential modification steps. Here, we introduce a novel (time-resolved) TiO{sub 2}-photocatalysis laser ablation electrospray ionization (LAESI) MS method for the analysis of drug candidates. This method was proven to be compatible with both TiO{sub 2}-coated glass slides as well as solutions containing suspended TiO{sub 2} nanoparticles, and the results were in excellent agreement with studies on biological oxidation of verapamil, buspirone, testosterone, andarine, and ostarine. Finally, a time-resolved LAESI MS setup was developed and initial results for verapamil showed excellent analytical stability for online photocatalyzed oxidation reactions within the set-up up to at least 1 h. .

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Regulating the properties of activated carbon for supercapacitors: impact of particle size and degree of aromatization of hydrochar

Hydrochar (HC), obtained by the hydrothermal carbonization (HTC) of biomass, is an excellent precursor for preparing activated carbon (AC). However, the effects of the intrinsic properties of HC on the microstructure and electrochemical properties of AC are largely unknown. Here, this study investigates the impact of particle size and the degree of aromatization of in-situ HC on the microstructure and electrochemical properties of AC. Our results show that a large particle size and a high degree of aromatization help protect the HC from overactivation by ZnCl 2 , resulting in an large specific surface area (SSA > 2000 m 2 /g) and high mesopore to micropore volume ratio value ( V mes /V mic > 0.3) of the AC. Electrochemical performance measurements show a maximum specific capacitance of 218 F/g at 0.5 A/g was achieved in all samples where the AC (AC180-10 h) was prepared by activating HC180-10 h with a large size, a high degree of aromatization, and abundant surface oxygen-containing functional groups. After AC180-10 h was assembled into a supercapacitor, the specific capacitance of AC180-10 h still reached 158 F/g at 0.5 A/g, and it showed excellent cycling stability. This study advances the understanding of the impact of HC particle size and degree of aromatization on AC properties, providing new insights into tailoring HC qualities so that improving improve the properties of AC.

36 MATERIALS SCIENCE↗

Synthesis of Mg–K-biochar bimetallic catalyst and its evaluation of glucose isomerization

Highly efficient isomerization of glucose to fructose is essential for valorizing cellulose fraction of biomass to value-added chemicals. This work provided an innovative method for preparing Mg-biochar and Mg–K-biochar catalysts by impregnating either MgCl 2 alone or in combination with different K compounds (Ding et al. in Bioresour Technol 341:125835, 2021, https://doi.org/10.1016/j.biortech.2021.125835 and KHCO 3 ) on cellulose-derived biochar, followed by hydrothermal carbonization and pyrolysis. Single active substance MgO existing in the 10 Mg–C could give better catalytic effect on glucose isomerization than the synergy of MgO and KCl crystalline material present in 10 Mg–KCl–C. But the catalytic effect of 10 Mg–C was decreased when the basic site of MgO was overloaded. Compared to other carbon-based metal catalysts, 10 Mg–KHCO3–C with 10 wt% MgCl 2 loading had excellent catalytic performance, which gave a higher fructose yield (36.7%) and selectivity (74.54%), and catalyzed excellent glucose conversion (53.99%) at 100 °C in 30 min. Scanning electron microscope–energy dispersive spectrometer and X-Ray diffraction revealed that the distribution of Mg 2+ and K+ in 10 Mg–KHCO 3 –C was uniform and the catalytic active substances (MgO, KCl and K2CO 3 ) were more than 10 Mg–C (only MgO). The synergy effects of MgO and K 2 CO 3 active sites enhanced the pH of reaction system and induced H 2 O ionization to form considerable OH– ions, thus easily realizing a deprotonation of glucose and effectively catalyzing the isomerization of glucose. In this study, we developed a highly efficient Mg–K-biochar bimetallic catalyst for glucose isomerization and provided an efficient method for cellulose valorization.

59 BASIC BIOLOGICAL SCIENCES↗

Enhanced oxidation resistance of (Mo 95 W 5 ) 85 Ta 10 (TiZr) 5 refractory multi-principal element alloy up to 1300°C

Refractory-metal-based alloys are a potential replacement of current nickel-based superalloys due to their excellent mechanical strength at extremely high temperatures. However, severe oxidation in a high-temperature working environment limits their application. To address this challenge, a two-step coating process (including a Mo precoat and a Si-B pack cementation) was applied to an innovative refractory multi-principal element alloy (RMPEA) (Mo 95 W 5 ) 85 Ta 10 (TiZr) 5 . The coating is composed of an aluminoborosilica glass layer on top of a RMPEA-Si-B multilayered structure. Here, the coating effectively protects the RMPEA from oxidation in high-temperature environments, as demonstrated by phase-stable operation at 10–20% higher temperatures over state-of-the-art systems without any forced-cooling system. Following an isothermal exposure at 1300 °C, the weight change of the coated sample follows a paralinear kinetics with a minor weight loss of 4.2 mg/cm 2 after 50 h. Thermal cycling tests between 1300 °C and room temperature in air resulted in the total weight gain of only 2.6 mg/cm 2 after 450 cycles. The coating shows an excellent adherence to the substrate with a boride layer acting as a barrier that maintains the coating integrity. This two-step Mo-Si-B coating method can be adapted to provide environmental resistance to a wide range of RMPEA.

36 MATERIALS SCIENCE↗

Synergy of tensile strength and high cycle fatigue properties in a novel additively manufactured Al-Ni-Ti-Zr alloy with a heterogeneous microstructure

Alloy design strategies in additive manufacturing (AM) to achieve grain refinement and terminal eutectic solidification have been introduced to engineer Al alloys having microstructural hierarchy and heterogeneity. Such alloy design strategies enable crack-free builds with an expanded AM processing window and pushed the strength limit in Al alloys. However, fatigue performance of Al alloys made by AM is restricted by the presence of process induced defects and its stochasticity. In this work, tensile and high cycle fatigue (HCF) behavior of a novel Al-Ni-Ti-Zr alloy with a heterogeneous microstructure is studied in the as-built condition, supplemented by detailed microstructural and mechanical characterization. Excellent strength-ductility synergy of 342 MPa and 16% failure strain achieved in the alloy was associated with the microstructural attributes that pertain to the novel alloy. Additionally, the alloy showed excellent HCF performance with a fatigue endurance limit to ultimate tensile strength ratio of 0.29 in flexural fatigue mode. The study revealed the existence of multiple crack retardation mechanisms and favorable crack propagation pathways through the fine-grained regions which enabled good fatigue performance to the alloy. Further, a probabilistic model has been used to estimate the fatigue life of the alloy as a function of the stochastic microstructure by utilizing the statistical distribution of pores, solid-state inclusions, and grains in the AM Al alloy. Finally, the model parametric trends are consistent with the experimental observations.

36 MATERIALS SCIENCE↗

The SCALE/AMPX multigroup cross section processing for fast reactor analysis

The SCALE/AMPX multigroup (MG) cross section processing procedure has been updated to minimize reactivity differences for fast reactor designs and boiling water reactors (BWRs) with very high void fractions to provide excellent agreement with continuous-energy reference calculations. SCALE MG calculations are widely applied to thermal spectrum light-water reactor (LWR) systems as well as fast spectrum metallic systems of interest to National Nuclear Security Administration. With growing interest from industry and regulators in applying SCALE for the design of fast spectrum reactors, both sodium and molten salt, and in the licensing of power up rates for BWRs, it is desirable to review the SCALE/AMPX procedure for unresolved resonance self-shielded data and high energy neutron spectra. The data were improved by generating MG unresolved resonance data based on the analytic probability table method with the narrow resonance approximation as well as the use of a very fine group structure typically used in fast system analysis. This study focused on verifying the probability table and the SCALE/AMPX MG cross section processing procedure by performing reaction rate analysis and benchmark calculations for various fast reactor and high void BWR systems. Here, results indicate that the improved SCALE/AMPX MG cross section processing provides excellent results for the fast reactor analysis.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

ZIF-67 incorporated with carbon derived from pomelo peels: A highly efficient bifunctional catalyst for oxygen reduction/evolution reactions

Developing carbon catalyst materials using natural, abundant and renewable resources as precursors plays an increasingly important role in clean energy generation and environmental protection. In this work, N-doped pomelo-peel-derived carbon (NPC) materials were prepared using a widely available food waste-pomelo peels and melamine. The synthetic NPC exhibits well-defined porosities and a highly doped-N content (e.g. 6.38 at% for NPC-2), therefore affords excellent oxygen reduction reaction (ORR) catalytic activities in alkaline electrolytes. NPC was further integrated with ZIF-67 to form ZIF-67@NPC hybrids through solvothermal reactions. The hybrid catalysts show substantially enhanced ORR catalytic activities comparable to that of commercial 20 wa Pt/C. Furthermore, the catalysts also exhibit excellent oxygen evolution reaction (OER) catalytic activities. Among all prepared ZIF-67@NPC hybrids, the optimal composition with ZIF-67 to NPC ratio of 2:1 exhibits the best ORR and OER bifunctional catalytic performance and the smallest Delta E (E-OER@10 mA cm(-2)-E-ORR@-1 mA cm(-2)) value of 0.79 V. The catalyst also demonstrated desirable 4-electron transfer pathways and superior catalytic stabilities. The Co-N-4 in ZIF-67, electrochemical active surface area, and the strong interactions between ZIF-67 and NPC are attributed as the main contributors to the bifunctional catalytic activities. These factors act synergistically, resulting in substantially enhanced bifunctional catalytic activities and stabilities; consequently, this hybrid catalyst is among the best of the reported bifunctional electrocatalysts and is promising for use in metal-air batteries and fuel cells. (C) 2016 Elsevier B.V. All rights reserved.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Elucidation of Fe-N-C electrocatalyst active site functionality via in-situ X-ray absorption and operando determination of oxygen reduction reaction kinetics in a PEFC

In the past decade the notable effort placed on improving intrinsic electrochemical kinetics of platinum group metal (PGM)-free electrocatalysts for the oxygen reduction reaction (ORR) has led to a significant improvement in both performance and understanding of this class of electrocatalysts. However, a limited amount of this development and understanding has been undertaken using operando electrochemical diagnostics at the membrane electrode assembly (MEA) level. In this work, the operando ORR kinetics on an atomically dispersed iron-nitrogen-carbon ((AD)Fe-N-C) PGM-free electrocatalyst have been examined to extract the reaction order and the activation energy of the ORR. The experiments were carefully designed to ensure the stability/predictability of the electrocatalyst during the data collection process and thus validate the relevance of the values obtained for the aforementioned parameters. A kinetic model that considers a potential-dependent availability of active sites (θ) is proposed. Active site availability is shown to be a function of both the change in the oxidation state (nR) and the redox potential at which the metal center transitions from a higher oxidation state to a lower one (). The resulting model fitting parameters for nR and (0.71 and 0.788 V, respectively) obtained from the analysis of operando data correlate well with those from in situ X-ray absorption near edge structure measurements (nR=0.57) and in situ cyclic voltammetry measurements (0.75 V < <0.8 V) in the MEA environment. The resulting model provides an excellent fit of MEA performance across the range of pressures, temperatures, and potentials under which the data were collected.

Activation energy↗

Dual-atom Ag 2 /graphene catalyst for efficient electroreduction of CO 2 to CO

Electrochemical reduction of CO 2 into value-added carbon compounds offers a promising strategy to mitigate global warming, but present challenges for chemistry due to the poor selectivity and stability of electrocatalysts. In this work, we report a dual-atom Ag 2 /graphene catalyst featuring well-defined AgN 3 -AgN 3 active site for CO 2 electrochemical reduction. This dual-atom catalyst can drive CO 2 reduction reaction at a potential as high as -0.25 V, and exhibit excellent CO Faradic efficiency up to 93.4 % with a current density of 11.87 mA cm -2 at -0.7 V and long-term stability, far surpassing the single-atom Ag 1 /graphene and the traditional silver nanoparticle catalysts. Finally, DFT calculations reveal that the dual-atom Ag site lowers the barrier for the formation of *COOH by stabilizing the *CO 2 through the concomitant interactions with the C and an O atom of CO 2 , resulting in excellent catalytic performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗