Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain microstructure evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Microstructural Progression of Shear-Induced Mixing in a CuNi Alloy

Shear deformation has been highlighted in multiple research efforts for its ability to impart mechanical properties improvements and unique microstructures. When used to process and densify powdered material, these shear-based consolidation techniques are commonly referred to as friction consolidation (FC). In this paper, we have examined the microstructural evolution from compacted Cu and Ni powders to a consolidated Cu0.5Ni0.5 alloy. We have shown various stages of porosity reduction and preferential deformation being accommodated by the more ductile material early in the process, leading to formation of a tortuous microstructural zone. Porosity reduction was extensive, decreasing from ~65% in the unprocessed powder to ~1% in the fully consolidated alloy. The final consolidated alloy showed roughly a 2X hardness improvement over the unalloyed, compacted material. Unique aspects of this work include demonstration of the ability to use FC processing to produce a submicron and equiaxed grain size in samples within a 0.5 to 2 minute processing time.

Overman, Nicole R.↗

Deformation and fracture characteristics of zirconium plate produced via ultrasonic additive manufacturing

Abstract The microstructural evolution, deformation modes, and fracture mechanisms of zirconium plate produced using ultrasonic additive manufacturing (UAM) are presented. In addition to conventional tensile testing techniques, digital image correlation captured highly variable strain accumulation in specimens loaded perpendicular or parallel to the build height (Z). When tested in parallel to Z, delamination at prior foil/foil interfaces creates strain localization noticeable in strain rate maps, whereas specimens loaded perpendicular to Z illustrate conventional strain hardening until necking accelerates delamination. Although bond strengths are statistically and spatially variable, in situ electron backscattering diffraction tests illustrate the ability for grains near interfaces to accommodate strain with twinning and slip modes consistent with conventionally produced zirconium alloys. Finally, mixtures of ductile and delamination-induced fracture highlight the interface-driven failure modes of UAM zirconium plate in the as-built condition. Graphic abstract

36 MATERIALS SCIENCE↗

Microstructural evolution of NARloy-Z at elevated temperatures

Microstructural evolution was studied in samples of wrought and vacuum plasma sprayed (VPS) NARloy-Z exposed to temperatures up to 970 C (1,780 F) for up to 60 h. Samples were heated in a vacuum furnace, followed by rapid quenching in helium (He) gas at a cooling rate of 166 C (300 F) per second. Microstructural analyses were conducted using optical microscopy, scanning electron microscopy (SEM), and electron probe microanalysis (EPMA). In both the wrought and VPS conditions, precipitates rich in silver (Ag) and zirconium (Zr) were present in the matrix and at the grain boundaries even after long exposure to elevated temperatures. Islands rich in oxygen (O2) and Zr were also observed, as well as incipient melting at the grain boundary triple points. Results indicated that the alloy cannot be homogenized by heat treatment at elevated temperatures.

Singh, J.↗

An Object-Oriented Finite Element Framework for Multiphysics Phase Field Simulations

The phase field approach is a powerful and popular method for modeling microstructure evolution. In this work, advanced numerical tools are used to create a phase field framework that facilitates rapid model development. This framework, called MARMOT, is based on Idaho National Laboratory's finite element Multiphysics Object-Oriented Simulation Environment. In MARMOT, the system of phase field partial differential equations (PDEs) are solved simultaneously with PDEs describing additional physics, such as solid mechanics and heat conduction, using the Jacobian-Free Newton Krylov Method. An object-oriented architecture is created by taking advantage of commonalities in phase fields models to facilitate development of new models with very little written code. In addition, MARMOT provides access to mesh and time step adaptivity, reducing the cost for performing simulations with large disparities in both spatial and temporal scales. In this work, phase separation simulations are used to show the numerical performance of MARMOT. Deformation-induced grain growth and void growth simulations are included to demonstrate the muliphysics capability.

36 MATERIALS SCIENCE↗

A new smoothed particle hydrodynamics non-Newtonian model for friction stir welding: Process modeling and simulation of microstructure evolution in a magnesium alloy

We present a new smoothed particle hydrodynamics (SPH) model for friction stir welding (FSW). FSW has broad commercial application in the marine, aerospace, rail, and automotive industries. However, development of the FSW process for each new application has remained largely empirical. Few established numerical modeling techniques have been developed that can explain and predict important features of the process physics involved in FSW. This is particularly true in the areas of material flow and mixing mechanisms. In this paper, we present a novel modeling approach to simulate FSW that may have significant advantages over current finite element or finite difference based methods. Unlike traditional grid-based methods, Lagrangian particle methods such as SPH can simulate the dynamics of interfaces, large material deformations, and the material’s strain and temperature history without employing complex tracking schemes. Three-dimensional simulations of FSW on AZ31 Mg alloy are performed. The temperature history and distribution, grain size, microhardness as well as the texture evolution are presented. Numerical results are found to be in good agreement with experimental observations.

Pan, Wenxiao↗

Incorporating dynamic recrystallization into a crystal plasticity model for high-temperature deformation of Ti-6Al-4V

During hot deformation of (α + β) titanium alloys, the simultaneous action of strain and temperature in the (α + β) regime facilitates dynamic recovery, dynamic recrystallization (DRX), and phase transformations via non-equilibrium paths. DRX is manifested in the form of fine recrystallized α or β grains. Here, in the present study, a two-phase crystal plasticity finite element framework (CP-DRX) has been developed which incorporates DRX kinetics into the crystal plasticity (CP) model to predict the flow characteristics of Ti-6Al-4V alloys during thermo-mechanical processing. The CP slip system parameters, as well as elastic properties from both α and β phases of Ti, are calibrated for different strain rate conditions. An EBSD-informed two-phase microstructure representation has been utilized in the CP-DRX framework to explore the time-dependent evolution of DRX microstructure and crystal orientation for different strain rate conditions. The proposed CP-DRX can capture the evolution of crystal orientation and plastic flow stress–strain response of polycrystalline Ti-6Al-4V during the deformation process. Furthermore, the proposed model is able to capture the softening behavior, observed in average stress–strain response from experiments performed using a Gleeble thermomechanical simulator and predict the recrystallization texture.

(α+ β)-Titanium (Ti) Alloys↗

Correlation Between Structural Parameters and Mechanical Properties of Al5083 Sheets Processed by ECAR

In the paper, structural parameters and mechanical properties of Al5083 alloy sheet during equal channel angular rolling (ECAR) process and their relationship are studied. In order to evaluate the effect of ECAR process, Al5083 strips were subjected to the ECAR process for 1, 2, and 3 passes through the die channel angles 110°, 120°, and 130° at two routes. The effect of the process on the microstructural evolution of samples was investigated by means of x-ray diffraction and EBSD techniques. X-ray pattern has been analyzed using Rietveld method to compute structural parameters, including microstrain, average crystallite size, and dislocation density. The results showed that the dislocation density and microstrain were increased, and crystallite size was decreased during ECAR process. It was found that the behavior of variations in mechanical properties was in accordance with the dislocation density changes. This paper revealed that the increase in the strength of ECARed samples could be attributed to reduction in high-angle grain boundaries and the increase in dislocation density. Moreover, the yield strength estimated from Taylor equation was found in accordance very well with the experimentally measured yield strength of the samples.

36 MATERIALS SCIENCE↗

Characterizing the Effect of Thermal Processing on Feedstock Al Alloy Powder for Additive Manufacturing Applications

Gas-atomized metallic powders are commonly used in additive manufacturing processes. Research has shown that, for certain AM techniques, the chemistry and microstructural properties of the feedstock powders significantly affect the properties of the consolidated material. Understanding the powder characteristics before use in additive manufacturing can lead to optimizing properties of additively manufactured materials as well as determining the recyclability of feedstock powders. This research studies the effect of various solution treatment processes on the characteristics and microstructural evolution of powder aluminum alloy 6061. Solution treatment times and temperatures were guided by thermodynamic and kinetic modeling. Light microscopy, scanning electron microscopy, and hardness were used to evaluate each condition in both two and three dimensions. Results indicate that the Mg{sub 2}Si present in the untreated condition dissolves after 60 min of solution treatment, while there are competing effects from the dissolution and concurrent growth of various Fe-containing phases. Additionally, it is shown that both granular and sub-granular structures exist in these rapidly solidified powders, and the sub-grains reorient themselves during solution treatment.

36 MATERIALS SCIENCE↗

Microstructure, precipitates and hardness of selectively laser melted AlSi10Mg alloy before and after heat treatment

Highlights: • Microstructural characterization of SLM AlSi10Mg alloy and comparison with cast and powder AlSi10Mg • Effect of solution heat treatment and aging on the hardness change of SLM AlSi10Mg alloy • Evolution of strengthening precipitates and Fe-rich intermetallics in SLM AlSi10Mg during heat treatment - Abstract: The microstructure and precipitates within selectively laser melted (SLM) AlSi10Mg alloys in the as-built state and after T6 heat treatment were examined and correlated to the hardness evolution. The as-built alloy exhibited columnar patterns perpendicular to the build-direction and fish-scale pattern along the build-direction originating from the melt pool. The microstructure consisted of fine Al cells and eutectic structure with up to 4 μm in size. Tiny needle-like Si particles with highly faulted structure were identified within the Al cells and formed semi-coherent interface with the matrix. Nanoscale Si particles and π-Al{sub 8}Si{sub 6}Mg{sub 3}Fe phase were observed to segregate along the cell and grain boundary. Solution heat treatment (SHT) at 520 °C resulted in the dissolution of Al cellular microstructure. Precipitation and coarsening of the Si particles occurred, while the aspect ratio of Si particles remained nearly constant. The π-Al{sub 8}Si{sub 6}Mg{sub 3}Fe phase decomposed into plate-shaped β-Al{sub 5}SiFe. The artificial aging (AA) at 160 °C did not alter the microstructure but led to the formation of metastable Mg{sub 2}Si precipitates. The GP zones and β″ were identified through transmission electron microscopy after AA of 6 h, and β″ existed up to AA of 24 h. The hardness decreased after SHT due to the coarsening of the microstructure and reduced solid solution hardening. Hardness reached maximum magnitude after AA of 6–10 h due to the precipitation hardening, and remained relatively unchanged up to AA of 24 h. Microstructure and/or hardness of gas atomized powders and bulk cast AlSi10Mg alloys were also examined as references.

36 MATERIALS SCIENCE↗

Microstructural Characterization of Deformation Localization at Small Strains in a Neutron Irradiated 304 Stainless Steel

Deformation localization and structure evolution were investigated in an AISI 304 austenitic stainless steel deformed to 0.8% strain. Using SEM-EBSD, it was shown local plastic deformation may reach significant levels even when the bulk averaged strain level remains below 1%. Local misorientation values up to 24 were observed in these regions of high local plastic deformation. EBSD analysis of FIB lift-out specimens demonstrated that local misorientation level was highest near the free surface and diminished with increasing depth. (S)TEM observations on the same specimen indicated the local density of dislocation channels may vary up to an order of magnitude depending on local grain configuration, distance to the surface and/or local grain boundary structure. It was found that in the case of RT deformation, dislocation defect-free channels may contain twin or may be twin-free with twinning occurring inside channels. Formation of BCC-phase colonies (martensite) was observed in near-surface layer whereas no transformation in the volume of the specimen was detected at this strain level. Martensite formation was associated with channel-grain boundary intersection points where high local misorientation was observed using EBSD.

Deformation↗

Transient Microstructure Evolutions and Local Properties of Dual-Phase 980 MPa Grade Steel Via Friction Stir Spot Processing

Friction stir processing is a novel solid-state process to modify microstructures and their properties by intense, localized plastic deformation. However, little research has been reported for microstructure evolutions of advanced high-strength steels during the process. The present work focuses on the study of transient microstructure changes and local mechanical properties for friction stir spot processed dual-phase (DP) 980 MPa grade steel (DP980) under different peak temperatures. A pinless silicon nitride ceramic tool was used to produce relatively simple material deformation and flow near the tool. Friction stir spot processed steel samples were characterized by optical and electron microscopies. Furthermore, Vickers microhardness and nano-indentation measurements were used to study local mechanical properties for correlation with microstructures. A swallow layer of refined grains (<0.6 µm) was obtained with a low peak temperature (under 400 °C), whereas higher peak temperatures (>Ac 1 ) led to a change in grain size with different microstructures (fine-grained DP or martensite). Electron back-scattered diffraction characterizations revealed a large deformation in the as-received microstructures (mixture of ferrite and tempered martensite) induced by friction stir spot processing, leading to recrystallization and grain refinement around the stirred zone. Also, nano-indentation measurements showed a higher hardness than the hardness of the as-received DP980. Friction stir processing with different process conditions effectively changed microstructures and local mechanical properties.

36 MATERIALS SCIENCE↗

Reactivity of Shale to Supercritical CO 2 : Insights from Microstructural Characterization and Mineral Phase Evolution in Caney Shales for CCUS Applications

Understanding mineral–fluid interactions in shale under supercritical CO 2 (scCO 2 ) conditions is relevant for assessing long-term geochemical containment. This study characterizes mineralogical transformations and elemental redistribution in five Caney Shale samples serving as proxies for reservoir (R1, R2, R3) and caprock (D1, D2) facies, subjected to 30-day static exposure to pure scCO 2 at 60 °C and 17.23 MPa (2500 psi), with no brine or impurities introduced. SEM-EDS analyses were conducted before and after exposure, with mineral phases classified into silicates, carbonates, sulfides, and organic matter. Initial compositions were dominated by quartz (38–47 wt.%), illite (16–23 wt.%), carbonates (12–18 wt.%), and organic matter (8–11 wt.%). Post-exposure, carbonate loss ranged from 15 to 40% in reservoir samples and up to 20% in caprock samples. Illite and K-feldspar showed depletion of Fe 2+ , Mg 2+ , and K + at grain edges and cleavages, while pyrite underwent oxidation with Fe redistribution. Organic matter exhibited scCO 2 -induced surface alteration and apparent sorption effects, most pronounced in R2 and R3. Elemental mapping revealed Ca 2+ , Mg 2+ , Fe 2+ , and Si 4+ mobilization near reactive interfaces, though no secondary mineral precipitates formed. Reservoir samples developed localized porosity, whereas caprock samples retained more structural clay integrity. The results advance understanding of mineral reactivity and elemental fluxes in shale-based CO 2 sequestration.

geochemical CO2 sequestration↗

Phase transformation kinetics model for metals

We develop a new model for phase transformation kinetics in metals by generalizing the Levitas–Preston (LP) phase field model of martensite phase transformations (see Levitas and Preston (2002a,b) and Levitas et al. (2003)) to arbitrary pressure. Furthermore, we account for and track: the interface speed of the pressure-driven phase transformation, properties of critical nuclei, as well as nucleation at grain sites and on dislocations and homogeneous nucleation. The volume fraction evolution of each phase is described by employing KJMA (Kolmogorov, 1937; Johnson and Mehl, 1939; Avrami, 1939, 1940, 1941) kinetic theory. We then test our new model for iron under ramp loading conditions and compare our predictions for the α → ϵ iron phase transition to experimental data of Smith et al. (2013). In conclusion, more than one combination of material and model parameters (such as dislocation density and interface speed) led to good agreement of our simulations to the experimental data, thus highlighting the importance of having accurate microstructure data for the sample under consideration.

36 MATERIALS SCIENCE↗

Microstructure and hardness evolution induced by annealing of ion irradiated LiTaO 3

We report the evolution of the microstructure and mechanical properties of low-energy heavy-ion-irradiated LiTaO 3 crystals annealed at various temperatures was investigated by transmission electron microscopy (TEM) observations and nanoindentation tests to extend the applications of irradiated LiTaO 3 crystals. Before annealing, randomly distributed voids formed in an approximately 200 nm thick region at the end of the ion irradiation range, which was attributed to preferential absorption of interstitials by the amorphous-crystalline interface. After annealing, a new directional diffusion path of defects was identified, resulting in a void string. Furthermore, void string diffusion to the free surface was also found during the annealing temperature increase process, which offers a potential application in designing custom sized-thickness exfoliation at the nanoscale. Meanwhile, two competing processes were identified during the annealing process: epitaxial recrystallization from the amorphous-crystalline interface and grain nucleation process in the amorphous region, which formed phases different from the matrix crystal structure, resulting in an interaction between them. Furthermore, the hardness of irradiated samples was also found to be affected by the annealing process; in particular, a hardness decrease induced by the interstitial Fe ions in the recrystallized region was also confirmed, which can improve the processability of samples for further application.

36 MATERIALS SCIENCE↗

Understanding the Mechanism of Dynamic Recrystallization During High-Temperature Deformation in Nb-1Zr-0.1C Alloy

In the present investigation, a systematic study of the evolution of microstructure and crystallographic texture during hot deformation of Nb-1Zr-0.1C was carried out in the temperature range 1773-1973 K (1500-1700 °C) at different strain rates of 0.001, 0.01 and 0.1 s{sup −1}. The aim was to examine the mechanisms of dynamic recovery and recrystallization in a high-temperature range. A detailed microstructural analysis of the deformed samples was performed using the electron backscatter diffraction technique to study the occurrence and nature of various dynamic restoration processes; the different regimes of dynamic recovery and recrystallization were identified. The orientations of the dynamically recrystallized grains were found to be (001) .

36 MATERIALS SCIENCE↗

Modeling of intragranular misorientation and grain fragmentation in polycrystalline materials using the viscoplastic self-consistent formulation

In this paper, the recently established methodology to use known algorithmic expressions of the second moments of the stress field in the grains of a polycrystalline aggregate for calculating average fluctuations of lattice rotation rates and the associated average intragranular misorientation distributions using the mean-field viscoplastic self-consistent (VPSC) formulation is extended to solve the coupled problem of considering the effect of intragranular misorientations on stress and rotation rate fluctuations. In turn, these coupled expressions are used to formulate and implement a grain fragmentation (GF) model in VPSC. Case studies, including tension and plane-strain compression of face-centered cubic polycrystals are used to illustrate the capabilities of the new model. GF-VPSC predictions of intragranular misorientation distributions and texture evolution are compared with experiments and full-field numerical simulations, showing good agreement. In particular, the inclusion of misorientation spreads reduced the intensity of the deformed texture and thus improved the texture predictions. Finally and moreover, considering that intragranular misorientations act as driving forces for recrystallization, the new GF-VPSC formulation is shown to enable modeling of microstructure evolution during deformation and recrystallization, in a computationally efficient manner.

36 MATERIALS SCIENCE↗

Microstructural evolution of a silicon carbide-carbon coated nanostructured ferritic alloy composite during in-situ Kr ion irradiation at 300°C 450°C

This work focuses on irradiation behaviors of a novel silicon carbide and carbon coated nanostructured ferritic alloy (SiC-C@NFA) composite for potential applications as a cladding and structural material for next generation nuclear reactors. The SiC-C@NFA samples were irradiated with 1 MeV Kr ions up to 10 dpa at 300 and 450 °C. Microstructures and defect evolution were studied in-situ at the IVEM-Tandem facility at Argonne National Laboratory. The effects of ion irradiation on various phases such as α-ferrite matrix, (Fe,Cr) 7 C 3 , and (Ti,W)C precipitates were evaluated. The α-ferrite matrix showed a continuous increase in dislocation density along with spatial ordering of dislocation loops (or loop strings) at >5 dpa. The size of the dislocation loops at 450 °C was larger than that at 300 °C. The nucleation and growth of new (Ti,W)C precipitates in α-ferrite grains were enhanced with the ion dose at 450 °C. This study provides new insight into the irradiation resistance of the SiC-C@NFA system.

(FeCr)(7)C-3↗

Microstructure control to improve creep strength of alumina-forming austenitic heat-resistant steel by pre-strain

Highlights: • The effect of pre-strain on creep strength of AFA steel was studied. • The creep test was performed at 700°C and 200Mpa, and the aging test was carried out using box furnace at 700°C to simulate the microstructural evolution during creep. • Microstuctural evolution was observed by using SEM, EBSD, and TEM to investigate the relationship between creep strength and microstructure. - Abstract: At 700 °C and 200 MPa, the creep rupture time of W-containing alumina-forming austenitic heat-resistant (WAFA) steel increases from 1044 to 3119 h by pre-strain. Pre-strain introduces a lot of dislocation into the matrix and most of the dislocations remain stable to the end of creep without recovery and recrystallization. In addition, the dislocations have enabled secondary NbC and Laves phase to be uniformly distributed and refined. However, the dislocations lower grain boundary strength due to the coarsening of precipitates along grain boundaries Therefore, the increase in the creep rupture time in spite of deterioration of grain boundary strength is attributed to the dislocation strengthening and enhanced precipitation hardening within grains.

36 MATERIALS SCIENCE↗