Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphite Characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

High-throughput Li plating quantification for fast-charging battery design

Fast charging of most commercial lithium-ion batteries is limited due to fear of lithium plating on the graphite anode, which is difficult to detect and poses considerable safety risk. In this report we demonstrate the power of simple, accessible and high-throughput cycling techniques to quantify irreversible Li plating spanning data from over 200 cells. We first observe the effects of energy density, charge rate, temperature and state of charge on lithium plating, use the results to refine a mature physics-based electrochemical model and provide an interpretable empirical equation for predicting the plating onset state of charge. We then explore the reversibility of lithium plating and its connection to electrolyte design for preventing irreversible Li accumulation. Finally, we design a method to quantify in situ Li plating for commercially relevant graphite|LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC) cells and compare with results from the experimentally convenient Li|graphite configuration. The hypotheses and abundant data herein were generated primarily with equipment universal to the battery researcher, encouraging further development of innovative testing methods and data processing that enable rapid battery engineering.

25 ENERGY STORAGE↗

Methodologies for Design, Characterization and Testing of Electrolytes that Enable Extreme Fast Charging of Lithium-ion Cells

Selection, testing and validation of electrolyte candidates for Li-ion cells are discussed, based on a 10-minute target for extreme fast charge (XFC). A combination of modeling and laboratory measurements create a timely and synergistic approach to identifying candidate electrolyte formulations. Multi-solvent systems provide a balanced set of properties, wherein lower molecular-weight solvents offer reduced viscosity, increased species diffusivity, and mitigation of concentration polarization at high charge rates. Carefully selected formulations can exhibit peak conductivity and usable conductivity range of two to three times that of the baseline EC-EMC (3:7, wt.) + LiPF 6 . Candidates are also chosen based on stability and longevity within the cell environment. Lab testing coincides with property predictions from the Advanced Electrolyte Model (AEM) and a macro-scale cell model. Furthermore, cell testing utilized coin and pouch cells having NMC532 or NMC811 cathodes with graphite electrodes. Results indicate combinations of low-molecular weight solvents are key for fast-charge electrolytes as they extend the useful conductivity range to both low and higher salt concentrations, and possess higher self-diffusivities compared to conventional solvents. This reduces impacts from concentration polarization. The choice of electrolyte also influences the tendency for lithium metal deposition at the anode, as showcased by experimental and modeling results herein.

25 ENERGY STORAGE↗

X-ray absorption spectroscopic study of the alumina supported Fe and FeMo catalysts for methane dehydrogenation

Nanoscale Fe (5%Fe/Al 2 O 3 ) and FeMo (4.5%Fe-0.5%Mo/Al 2 O 3 ) catalysts are prepared by precipitating metal components onto alumina and then reducing in hydrogen at 700 °C for 2 hrs. Here, the catalysts are characterized before and after their exposures to methane at 700 °C, employing ex-situ X-ray absorption spectroscopy (XAS) and X-ray diffraction techniques. XAS data of the as-prepared catalysts shows that, iron precipitates onto alumina as 6L-ferrihydrite, and Mo is present as molybdate (Mo(VI)O 4 2- ). The molybdate, which binds the alumina in the as-prepared FeMo catalyst, is partially reduced to MoO 2 . The reduction of iron to metallic state is incomplete because the ferrous iron binds the alumina, forming hercynite. After several hrs of methane exposure to both the catalysts at 700 °C, a major Fe 3 C and a graphite phase are observed only in the FeMo catalyst. The observation confirms that the Mo promotes more iron to an active Fe metal, a part of that metal converts to Fe 3 C and austenite (Fe x C). Concurrently, the MoO 2 converts to Mo-oxycarbide (MoO x C y ), the latter then carburize to Mo 2 C in the FeMo catalyst. The Fe metal, Mo-oxycarbide and metal carbides are mainly responsible for the conversion of methane to H 2 and carbon. At reaction temperature > 900 °C, the Mo carbide particles agglomerate, and the excess carbon deposits on this agglomerate leading to catalyst deactivation. The deactivated catalyst is regenerated with CO 2 treatment at 1000 °C to restore its initial oxide structure.

30 DIRECT ENERGY CONVERSION↗

Lithium Metal Anodes for Rechargeable Batteries

Rechargeable lithium metal batteries have much higher energy density than those of lithium ion batteries using graphite anode. Unfortunately, uncontrollable dendritic lithium growth inherent in these batteries (upon repeated charge/discharge cycling) and limited Coulombic efficiency during lithium deposition/striping has prevented their practical application over the past 40 years. With the emerging of post Li-ion batteries, safe and efficient operation of lithium metal anode has become an enabling technology which may determine the fate of several promising candidates for the next generation of energy storage systems, including rechargeable Li-air battery, Li-S battery, and Li metal battery which utilize lithium intercalation compounds as cathode. In this work, various factors which affect the morphology and Coulombic efficiency of lithium anode will be analyzed. Technologies used to characterize the morphology of lithium deposition and the results obtained by modeling of lithium dendrite growth will also be reviewed. At last, recent development in this filed and urgent need in this field will also be discussed.

25 ENERGY STORAGE↗

Pyrolytic synthesis and characterization of N-doped carbon nanoflakes for electrochemical applications

Highlights: • Carbon nanoflakes doped with nitrogen were produced by a pyrolytic technique. • Quarternary, pyrrolic and pyridinic types of nitrogen are confirmed by XPS. • Nitrogen content depends on precursor used and temperature processed. • Specific surface area values decrease with increasing of synthesis duration. • N-doped carbon nanoflakes may be suitable for electrochemical applications. - Abstract: Nitrogen doped carbon nanoflakes, which are very important for many electrochemical applications, were synthesized by pyrolysis of nitrogen containing organic compounds over metal oxide template. Acetonitrile, pyridine and butylamine, which are of different volatility were tested as N-containing precursors. Morphology, structure and chemical composition of the as-synthesized materials were investigated by scanning electron microscopy (SEM), high resolution transmission electron microscopy (TEM), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). It was found that materials are highly defective and consist of a few malformed graphene layers. X-ray photoelectron spectra reflect the dominant graphitic and pyridinic N-bonding configuration. It was also noted that specific surface area depends on the duration and temperature of the reaction. Increase in duration and temperature led to decrease of the specific surface area from 1000 to 160 m{sup 2}/g, 1170 to 210 m{sup 2}/g and 1180 to 480 m{sup 2}/g for acetonitrile, butylamine and pyridine precursors, respectively.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Synchrotron measurements of local microstructure and residual strains in ductile cast iron

The local microstructure and distribution of thermally induced residual strains in ferrite matrix grains around an individual spherical graphite nodule in ductile cast iron (DCI) were measured using a synchrotron X-ray micro-diffraction technique. It is found that the matrix grains are deformed, containing dislocations and dislocation boundaries. Each of the residual strain components in the matrix grains exhibits a complex pattern along the circumferential direction of the nodule. Along the radial direction of the nodule, strain gradients from the interface to the grain interior are seen for some strain components, but only in some matrix grains. The observed residual strain patterns have been analysed by finite element modelling, and a comparison between the simulation and experiments is given. The present study of local residual stress by both experimental characterization and simulation provide much needed information for understanding the mechanical properties of DCI, and represent an important contribution for the microstructural design of new DCI materials.

Zhang, Y B↗

Experimental and Computational Analysis of NEAMS Pebble Bed Reactors

The Advanced High-Temperature Pebble Bed Reactor concept leverages a particle-based fuel format consisting of discrete spherical graphite pebbles arrayed in a packed bed architecture. Thermal regulation achieved via flow of gas (e.g., helium) or liquid (e.g., molten salt) coolants through the void spaces between pebbles in the bed (characteristic pebble diameters: ~ 6 cm, gas cooled; ~ 3 cm, liquid cooled). This design is of interest owing to inherent advantages including passive safety features and highly efficient heat transfer characteristics that enable high power densities to be achieved. Fully leveraging these advantages requires a fundamental understanding of the complex coolant flow structure within the pebble-shaped fuel bed. Unfortunately, complexities associated with non-invasively probing the micro-scale flow phenomena within the complex network of void spaces between pebbles have hindered efforts to characterize the underlying transport phenomena. Without this fundamental foundation, it becomes challenging to rationally construct macroscopic transport models based upon volume averages of micro-scale parameters that accurately capture the observed flow behavior. Consequently, this lack of fundamental knowledge has limited previous work to coarse comparisons between theory and extremely limited experimental data. Moreover, these comparisons have been made only in terms of integral or macroscopic results. Therefore, multipoint measurements with a high level of spatial and temporal resolution are critically needed to fully map the complex flow patterns and to provide data at high spatial density to permit accurate volume averaging in the pebble bed. For this project, we performed a coordinated experimental and computational effort to quantitatively map the full-field velocity and temperature fields in the interstitial spaces within the pebble bed. The major accomplishments of this project included the important knowledge acquired for the flow mixing and heat transfer in the interstitial pore scales, the effects of flow mixing in the near-wall and far-wall regions, and the by-pass flows of pebble bed systems. The produced high-resolution experimental data (not broadly available in existing literature) were then used for the numerical studies enabling the refinement and validation of standard simulation tools (Nek5000).

42 ENGINEERING↗

Fabrication and long-wavelength characterization of neat and chemically modified graphene

Graphene, a single- or several layer-thick carbon, attracts significant research activity because of its exceptional material properties. Graphene is a promising material for optoelectronic applications. Neat graphene demonstrates potential as a material for long wavelength photodetectors working at elevated temperatures. Chemical modification of graphene opens up many new applications of this material in electronics, in new composite materials, and in new catalysts for different chemical processes. Chemical vapor deposition-grown large-area graphene can be successfully modified with the creation of benzyne attachments. The investigation of microwave properties is an important part of graphene research. Two variants of near-field long wavelength microscopy were found efficient with graphene. Measurements with a probe formed by an electrically open end of a 4 GHz half-lambda parallel-strip transmission line resonator allow the implementation of an electrodynamic model of graphene microwave impedance. The results of near-field scanning superconducting quantum interference device (SQUID) RF microscopy of graphite and graphene at 200 MHz shed light on mechanisms of AC graphene response: screening currents induced in graphene by an external RF magnetic field tend to localize near structural defects.

36 MATERIALS SCIENCE↗

Integrative Additive Design for Robust SEI Formation in NMC811||Silicon Batteries

Silicon (Si) is considered a promising replacement for graphite anodes in lithium-ion batteries (LIBs) due to its high abundance and exceptional specific capacity, but its widespread commercialization has been hindered by poor electrochemical performance. Among various strategies, the use of functional additives has emerged as one of the most effective and cost-efficient methods to enhance the electrochemical properties of LIBs. In this study, several additives—vinylene carbonate (VC), vinyl ethylene carbonate (VEC), lithium difluorophosphate (LiDFP), lithium difluoro(oxalato)borate (LiDFOB), lithium tetrafluorooxalatophosphate (LiTFOP), and lithium difluorobis(oxalato)phosphate (LiDFBOP)—were systematically investigated in LiNi₀.₈Mn₀.₁Co₀.₁O₂ (NMC811)||Si full cells. Notably, LiDFBOP, a lithium salt containing two oxalate groups, outperformed all other additives, delivering the best capacity retention after 300 cycles. Comprehensive characterizations, including FTIR, SEM, and XPS, revealed that LiDFBOP's superior performance stems from its ability to form a more stable solid electrolyte interphase (SEI) on the Si anode, owing to its favorable molecular structure that integrates the beneficial features of the other additives.

25 ENERGY STORAGE↗

Raman spectroscopy of thermally perturbed carbon fibers: Discriminating spectral responses of modulus classes and defect types

The mechanical strength properties of carbon fibers are generally thought to be correlated with the presence of underlying atomic-level defects. These defects serve to break the underlying translational symmetry of the graphitic or graphene subunits of the fiber construction, resulting in the emergence of new Raman-active spectral features. However, historical attempts to classify the precise origin of defect contributions to the Raman spectra have been challenging because of indistinct and overlapping features in the carbon fiber Raman spectra. Further, while substantial research exists on high-temperature exposure in inert atmospheres for carbon fiber composites, comparatively less addresses microscale behaviors and Raman spectral alterations to monofilament carbon fibers exposed to high-temperature atmospheric environments. Here, we report Raman spectral responses of nine commercially available high-performance, polyacrylonitrile-based carbon fibers exposed to various atmospheric heat treatments. In this work, we introduce a model-independent characterization method, the integrated absolute difference, to quantify the spectral responses to heat treatment of different fiber modulus classes. We combine this new method with a newly reported strategy to standardize spectral fitting for carbon fibers. With this approach, we show that atomic-scale defects in the underlying fiber microstructure manifest in measurably distinct manners and have distinct responses to thermal perturbation. These combined approaches may lay the foundation for disentangling contributions from specific defects in the Raman spectra of carbon fibers.

36 MATERIALS SCIENCE↗

Polymorphic, Porous, and Host–Guest Nanostructures Directed by Monolayer–Substrate Interactions: Epitaxial Self-Assembly Study of Cyclic Trinuclear Au(I) Complexes on HOPG at the Solution–Solid Interface

Synthesis, crystallographic characterization, and molecular self-assembly of two novel cyclotrimeric gold(I) complexes, Au 3 [3,5-(COOEt) 2 Pz] 3 (Au 3 Pz 3 ) and Au 3 [(n-Pr–O)C=N(Me)] 3 (Au 3 Cb 3 ) was studied. Single crystal X-ray crystallography data reveal that both gold(I) complexes have one-dimensional stacking patterns caused by intermolecular Au(I)···Au(I) aurophilic interactions. The Au 3 Pz 3 trimer units stack with two alternate and symmetrical Au(I)···Au(I) interactions while the Au 3 Cb 3 units have three alternating and nonsymmetrical Au(I)···Au(I) interactions. Molecular self-assembly of the gold(I) complexes on the 1-phenyloctane/highly ordered pyrolytic graphite (HOPG) (0001) solution–solid interface is studied with scanning tunneling microscopy (STM). The gold(I) cyclotrimers form epitaxial nanostructures on the HOPG surface. At a concentration of ~1 × 10 –4 M, Au 3 Pz 3 complexes exhibit a single morphology, while Au 3 Cb 3 complexes exhibit polymorphology. Two polymorphs, one nonporous and the other porous, are observed at 22.0 ± 2.0 °C for Au 3 Cb 3 complexes. A nonporous, low-surface-density (0.82 molecules/nm 2 ) Au 3 Cb 3 nanostructure forms first and then transforms into a high-density (1.43 molecules/nm2) porous nanostructure. This is the first time any porous surface nanostructure is reported for an organometallic system. The porous structure is thought to be stabilized by a combination of hydrogen bonding and monolayer–substrate interactions. These pores are utilized to incorporate pyrene into the film, rendering this the first organometallic host–guest system imaged at the solid–solution interface. In conclusion, molecular and periodic density functional theory (DFT) calculations shed light on the two-dimensional topography and polymorphic self-assembly revealed by STM; these calculations suggest significant electronic hybridization of the Au 3 trimer orbitals and HOPG. The multiple-technique approach used herein provides insights concerning molecule–substrate and molecule–molecule interactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Quantification of Uncoupled Spin Domains in Spin-Abundant Disordered Solids

Materials often contain minor heterogeneous phases that are difficult to characterize yet nonetheless significantly influence important properties. Here we describe a solid-state NMR strategy for quantifying minor heterogenous sample regions containing dilute, essentially uncoupled nuclei in materials where the remaining nuclei experience heteronuclear dipolar couplings. NMR signals from the coupled nuclei are dephased while NMR signals from the uncoupled nuclei can be amplified by one or two orders of magnitude using Carr-Meiboom-Purcell-Gill (CPMG) acquisition. The signal amplification by CPMG can be estimated allowing the concentration of the uncoupled spin regions to be determined even when direct observation of the uncoupled spin NMR signal in a single pulse experiment would require an impractically long duration of signal averaging. We use this method to quantify residual graphitic carbon using 13 C CPMG NMR in poly(carbon monofluoride) samples synthesized by direct fluorination of carbon from various sources. Our detection limit for graphitic carbon in these materials is better than 0.05 mol%. The accuracy of the method is discussed and comparisons to other methods are drawn.

36 MATERIALS SCIENCE↗

INITIAL ANALYSIS OF TRANSIENT POWER TIME LAG DUE TO HETEROGENEITY WITHIN THE TREAT FUEL MATRIX.

The topic Nuclear Safety encompasses a broad spectrum of focal areas within the nuclear industry; one specific aspect centers on the performance and integrity of nuclear fuel during a reactivity insertion accident (RIA). This specific accident has proven to be fundamentally difficult to theoretically characterize due to the numerous empirically driven characteristics that quantify the fuel and reactor performance. The Transient Reactor Test (TREAT) facility was designed and operated to better understand fuel behavior under extreme (i.e. accident) conditions; it was shutdown in 1994. Recently, efforts have been underway to commission the TREAT facility to continue testing of advanced accident tolerant fuels (i.e. recently developed fuel concepts). To aid in the restart effort, new simulation tools are being used to investigate the behavior of nuclear fuels during facility’s transient events. This study focuses specifically on the characterizing modeled effects of fuel particles within the fuel matrix of the TREAT. The objective of this study was to (1) identify the impact of modeled heterogeneity within the fuel matrix during a transient event, and (2) demonstrate acceptable modeling processes for the purpose of TREAT safety analyses, specific to fuel matrix and particle size. Hypothetically, a fuel that is dominantly heterogeneous will demonstrate a clearly different temporal heating response to that of a modeled homogeneous fuel. This time difference is a result of the uniqueness of the thermal diffusivity within the fuel particle and fuel matrix. Using MOOSE/BISON to simulate the temperature time-lag effect of fuel particle diameter during a transient event, a comparison of the average graphite moderator temperature surrounding a spherical particle of fuel was made for both types of fuel simulations. This comparison showed that at a given time and with a specific fuel particle diameter, the fuel particle (heterogeneous) simulation and the homogeneous simulation were related by a multiplier relative to the average moderator temperature. As time increases the multiplier is comparable to the factor found in a previous analytical study from literature. The implementation of this multiplier and the method of analysis may be employed to remove assumptions and increase fidelity for future research on the effect of fuel particles during transient events.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of carbon ion implantation induced graded microstructure and phase transformation in stainless steel

Austenitic stainless steel 316L is ion implanted by carbon with implantation fluences of 1.2 × 10{sup 17} ions-cm{sup −} {sup 2}, 2.4 × 10{sup 17} ions-cm{sup −} {sup 2}, and 4.8 × 10{sup 17} ions-cm{sup −} {sup 2}. The ion implantation induced graded microstructure and phase transformation in stainless steel is investigated by X-ray diffraction, X-ray photoelectron spectroscopy and high resolution transmission electron microscopy. The corrosion resistance is evaluated by potentiodynamic test. It is found that the initial phase is austenite with a small amount of ferrite. After low fluence carbon ion implantation, an amorphous layer and ferrite phase enriched region underneath are formed. Nanophase particles precipitate from the amorphous layer due to energy minimization and irradiation at larger ion implantation fluence. The morphology of the precipitated nanophase particles changes from circular to dumbbell-like with increasing implantation fluence. The corrosion resistance of stainless steel is enhanced by the formation of amorphous layer and graphitic solid state carbon after carbon ion implantation. - Highlights: • Carbon implantation leads to phase transformation from austenite to ferrite. • The passive film on SS316L becomes thinner after carbon ion implantation. • An amorphous layer is formed by carbon ion implantation. • Nanophase precipitate from amorphous layer at higher ion implantation fluence. • Corrosion resistance of SS316L is improved by carbon implantation.

36 MATERIALS SCIENCE↗

A Single Small-Scale Plutonium Redox Reaction System Yields Three Crystallographically-Characterizable Organoplutonium Complexes

Here, an approach to obtaining substantial amounts of data from a hazardous starting material that can only be obtained and handled in small quantities is demonstrated by the investigation of a single small-scale reaction of cyclooctatetraene, C 8 H 8 , with a solution obtained from the reduction of Cp' 3 Pu (Cp' = C 5 H 4 SiMe 3 ) with potassium graphite. This one reaction coupled with oxidation of a product has provided single-crystal X-ray structural data on three organoplutonium compounds as well as information on redox chemistry thereby demonstrating an efficient route to new reactivity and structural information on this highly radioactive element. The crystal structures were obtained from the reduction of C 8 H 8 by a putative Pu(II) complex, (Cp' 3 Pu II ) 1– , generated in situ, to form the Pu(III) cyclooctatetraenide complex, [K(crypt)][(C 8 H 8 ) 2 Pu III ], 1-Pu , and the tetra(cyclopentadienyl) Pu(III) complex, [K(crypt)][Cp' 4 Pu III ], 2-Pu . Oxidation of the sample of 1-Pu with Ag(I) afforded a third organoplutonium complex that has been structurally characterized for the first time, (C 8 H 8 ) 2 Pu IV , 3-Pu . Complexes 1-Pu and 3-Pu contain Pu sandwiched between parallel (C 8 H 8 ) 2– rings. The (Cp' 4 Pu III ) – anion in 2-Pu features three η 5 -Cp' rings and one η 1 -Cp' ring, which is a rare example of a formal Pu–C η 1 -bond. In addition, this study addresses the challenge of small-scale synthesis imparted by radiological and material availability of transuranium isotopes, in particular that of pure metal samples. A route to an anhydrous Pu(III) starting material from the more readily available Pu IV O 2 was developed to facilitate reproducible syntheses and allow complete spectroscopic analysis of 1-Pu and 2-Pu . Pu IV O 2 was converted to Pu III Br 3 (DME) 2 (DME = CH 3 OCH 2 CH 2 OCH 3 ) and subsequently Pu III Br 3 (THF) x , which was used to independently synthesize 1-Pu , 2-Pu , and 3-Pu .

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Fracture Effects on Explosive Response (FEER); FY2018 Report

It is known that the violence of explosive response is affected by inertial and mechanical confinement. In a mechanical insult, the impact location creates a contact pressure that can act as confinement surrounding the ignition location, as has been observed in the Skid Test experiment. Under certain conditions — the details of which have not been well characterized — the ignition can produce cracking in the explosive, down which flames are observed to propagate. Cracks serve to simultaneously provide additional surface area for accelerating the reaction, as well as vent paths for quenching the reaction. These are competing behaviors, and the factors which govern the outcome are poorly described. A new experiment was devised to examine the effect of a controlled pre-load pressure on the explosive response. Sixteen experiments were performed on 1-inch thick discs of PBX 9501, with diameters of 1 in ch, 4.25 in ch, and 5 in ch. The explosive was compressed to a known pre-load between two clear windows and ignited at the center of the bottom surface with a focused laser impinging on a graphite inclusion. The ensuing reaction was imaged through the windows used to compress the sample, and from the side. A speckle pattern was applied to some samples for performing DIC (digital image correlation) for the purpose of quantifying the strain field and tracking crack growth. A threshold behavior was observed, in which higher-pressure pre-load resulted in cracks forming, while lower-pressure pre-load vented across the face of the explosive. This report presents the preliminary results, discusses the observations, enumerates hypotheses regarding the observed behavior, identifies lessons learned, and outlines a path forward for the next round of testing. Proof testing was only recently concluded and considerable additional analysis is required. These data will be valuable for the ongoing development of a constitutive mechanical and cracking failure model that will aid in predicting explosive response in mechanical impact scenarios.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Control of the Plasma-Material Interface for Long Pulse Optimization in the Experimental Advanced Superconducting Tokamak (EAST) (Final Report)

This project involved a collaborative effort, led by Dr. Rajesh Maingi of Princeton Plasma Physics Laboratory, to understand and control the plasma-material interface to improve long pulse discharge control and performance in the EAST devices. The focus is on long pulse recycling control and optimization, which can be challenging because of their broad range of materials used for plasma-facing components (PFC) and wall conditioning techniques. The purpose of the EAST device is to demonstrate long-pulse, stable, high performance plasma operation, providing a test-bed for key physics and technology issues for next step devices. As part of these tests, EAST has deployed carbon for the lower divertor PFC, tungsten for the upper divertor, and molybdenum for the main wall. In addition wall coatings are deployed for long pulse recycling control: lithium (Li) via several delivery tools, boronization, and recently also siliconization; for example, in 2013, a layer of SiC was deposited on all of the graphite tiles. Oxygen is also present at trace levels, making for a complex mix of materials and plasma-materials interactions (PMI). This mix of materials and the limited durability of wall coatings, coupled to partially optimized cryo-pumping, lead to evolution of the recycling off the PFCs, which restricts the duration of stationary, high performance, long pulse discharges. Comparing the wall conditioning techniques, Li enables the highest energy confinement and lowest recycling for the longest duration, while also suppressing ELMs in certain discharges. More specifically, research activities at the University of Tennessee focused on heat flux profile measurements in EAST, modeling the surface response, including the bonding energetics and chemical interactions between Li with carbon, tungsten, hydrogen and impurities, in addition to post situ experimental characterization and analysis of the divertor plasma facing components in EAST. This final report describes the overall progress within each of these tasks at the University of Tennessee within the project.

36 MATERIALS SCIENCE↗

A novel fiber-fretting test for tribological characterization of the fiber/matrix interface

Ceramic matrix composites exhibit excellent high temperature properties and are candidate materials for structural applications from jet engines to nuclear fuel cladding. The strength and deformation behavior of these composites are intrinsically tied to the properties of the fiber/matrix interface. This research introduces a novel technique to evaluate the fundamental friction and wear characteristics of these interfaces. A case study on SiC f /PyC/SiC m composites applies in situ fiber fretting to investigate the kinetic friction coefficient and cyclic wear characteristics of the interphase. The experimental methodology is presented in explicit detail to encourage other researchers to explore the capabilities of this technique. Additionally, testing was carried out as a function of fiber roughness, PyC thickness (≈10, 500, 1200 nm), cycle count (10, 100, 1000), and frequency (1, 5, and 10 Hz). The friction coefficient and wear behavior changed with cycle length due to a transition from adhesive to abrasive mechanisms. SEM fractography provided insights to tribological evolution from adhesive sliding to three-body abrasive wear. The structural disorder at the tribo-surface relating to graphitic content and dangling bond density was investigated using Raman spectroscopy. Properties are contextualized with comparison to uniaxial tensile behavior of the parent composite.

36 MATERIALS SCIENCE↗