Search NASA⌕ Search

SEARCH · Search NASA

Results for “Materials Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Friction and wear of oxide-ceramic sliding against IN-718 nickel base alloy at 25 to 800 C in atmospheric air

The friction and wear of oxide-ceramics sliding against the nickel base alloy IN-718 at 25 to 800 C were measured. The oxide materials tested were mullite (3Al2O3.2SiO2); lithium aluminum silicate (LiAlSi(x)O(y)); polycrystalline monolithic alpha alumina (alpha-Al2O3); single crystal alpha-Al2O3 (sapphire); zirconia (ZrO2); and silicon carbide (SiC) whisker-reinforced Al2O3 composites. At 25 C the mullite and zirconia had the lowest friction and the polycrystalline monolithic alumina had the lowest wear. At 800 C the Al2O3-8 vol/percent SiC whisker composite had the lowest friction and the Al2O3-25 vol/percent SiC composite had the lowest wear. The friction of the Al2O3-SiC whisker composites increased with increased whisker content while the wear decreased. In general, the wear-resistance of the ceramics improve with their hardness.

Sliney, Harold E.↗
NASA NTRS1990

Manual and computer-aided materials selection for industrial production: An exercise in decision making

Students are introduced to methods and concepts for systematic selection and evaluation of materials which are to be used to manufacture specific products in industry. For this laboratory exercise, students are asked to work in groups to identify and describe a product, then to proceed through the process to select a list of three candidates to make the item from. The exercise draws on knowledge of mechanical, physical, and chemical properties, common materials test techniques, and resource management skills in finding and assessing property data. A very important part of the exercise is the students' introduction to decision making algorithms, and learning how to apply them to a complex decision making process.

Bates, Seth P.↗
NASA NTRS1988

Evolution and use of combined mechanical and thermal codes for cryogenic turbopump bearings

Shaft bearing system analysis codes were developed, improved, and used to investigate Space Shuttle Main Engine (SSME) Liquid Oxygen (LOX) turbopump bearing problems, and to support the Marshall Space Flight Center Bearing and Seal Materials Test (BSMT) program. Thermal network modeling uses the SINDA thermal code, and the modeling of bearing quasi-dynamic characteristics uses the SHABERTH bearing/shaft code. These codes are solved concurrently for a bearing/shaft system using software developed for this purpose. Simulation of the SSME LOX turbopump turbine and pump end bearings and the MSFC BSMT operating in liquid nitrogen (LN sub 2) and LOX was done. The thermal network models include the bearing components, bearing carriers, shaft, housing, frictional heat, and viscous fluid energy. A cage model was included to account for heat generation between the cage and rolling elements. Since most bearing surfaces operate at temperatures well above the coolant saturation temperature, and move at high speed relative to the coolant, forced convection boiling is the dominant mechanism for heat removal. Improved modeling of forced convection film boiling was incorporated to take into account the local vapor generation at the high temperature surfaces. Rearing preloads in the pump and tester are provided by preload springs. As bearing operating clearances and contact angles change due to thermal effects and loading, the bearing preload changes with these varying conditions. These characteristics were modeled and are included in the overall system models. Results from these models indicate an operational limit which, if exceeded, predicts a thermal excursion.

Cody, Joe C.↗
NASA NTRS1989

1200 to 1400 K slow strain rate compressive properties of NiAl/Ni2AlTi-base materials

An attempt to apply the Martin Marietta Corporation's XD technology to the fabrication of NiAl-Ni2AlTi materials with improved creep properties is presented. Composite materials, containing from 0 to 30 vol pct of nominally 1-micron-diameter TiB2 particles in the intermetallic matrix have been produced by the XD process and compacted by hot pressing. Such composites demonstrated significant strength increases, approaching 3-fold for the 20 vol pct materials, in comparison to the unreinforced aluminide. This behavior was accomplished without deleterious side effects as the grain boundaries and particle-matrix interfaces were intact after compressive deformation to 10 percent or more strain. Typical true compressive stress-strain diagrams for materials tested in air between 1200 and 1400 K at approximate strain rates of 1.7 x 10 to the -6th/sec are presented.

Whittenberger, J. Daniel↗
NASA NTRS1989

Evaluation of atomic oxygen resistant protective coatings for fiberglass-epoxy composites in LEO

Fiberglass-epoxy composite masts are the prime structural members for the Space Station Freedom solar array. At the altitude where Space Station Freedom will operate, atomic oxygen atoms are the most predominant species. Atomic oxygen is highly reactive and has been shown to oxidize organic and some metallic materials. Tests with random and directed atomic oxygen exposure have shown that the epoxy is removed from the composite exposing brittle glass fibers which could be easily removed from the surface where they could contaminate space Station Freedom Systems. Protection or fiber containment systems, inorganic based paints, aluminum braid, and a metal coatinsg, were evaluated for resistance to atomic oxygen, vacuum ultraviolet radiation, thermal cycling, and mechanical flexing. All appeared to protect well against atomic oxygen and provide fiber containment except for the single aluminum braid covering. UV radiation resistance was acceptable and in general, thermal cycling and flexure had little to no effect on the mass loss rate for most coatings.

Rutledge, Sharon K.↗
NASA NTRS1990

Hydrogen permeation, diffusion and solubility in IN-100 and Waspaloy

An attempt has been made to determine the permeation rate of hydrogen in IN-100 and Waspaloy by determining the evolution rate of hydrogen from a closed capsule of the test materials. Enclosed vanadium hydride was the source of hydrogen in the capsule. The presentation discusses the treatment of data and assesses the validity of the techniques in permeation measurement. In addition to permeation experiments, the solubility and diffusion of hydrogen in IN-100 and Waspaloy were also determined. For hydrogen diffusion in Waspaloy, Delta H was 38.5 kJ and D(0) was 0.0026 sq cm/sec. For IN-100, Delta H was 68.2 kJ and D(0) was 0.059 sq cm /sec. Both IN-100 and Waspaloy exhibited limited solubility of hydrogen at pressures up to 340 atmospheres hydrogen.

Khan, A. S.↗
NASA NTRS1990

Compressive failure of thick-section composite laminates with and without cutouts subjected to biaxial loading

The composites studied are fiber composite laminate plates made of carbon fibers and a thermoplastic matrix material. Tests and results are given for: the solution convergence for transverse shear in a clamped plate without cutout under compression; the effects of cutout and laminate thickness on maximum shear in buckling and postbuckling response of a clamped plate under biaxial compression; the effects of cutout and laminate thickness on maximum shear in buckling and postbuckling response of a clamped plate under biaxial compression; and the effects of laminate thickness and cutout of the lowest three eigenvalues of a clamped plate under biaxial compression. Additional test results are given.

Rouxel, L.↗
NASA NTRS1991

Saltation threshold detection in a wind tunnel by the measurement of the net electrostatic charge

The Mars surface wind tunnel (MARSWIT) is an open circuit wind tunnel used for aeolian studies and is located inside a large vacuum chamber allowing testing at Martian surface atmospheric pressure. Since direct access is not available to the tunnel during operation at low pressure, a remote method of saltation detection is needed. The bed is observed by means of closed circuit video, but it is often difficult to determine the initiation of threshold. The measurement by means of an electrometer of the net electric charge produced by the saltating particles has provided a reliable means of saltation threshold detection. Saltating particles become charged several ways, both in wind tunnels and in a natural environment. The most significant of these methods are tribo-charging and contact charging, which always occur. Fracture charging may also occur under the high velocities associated with particle transport on Mars or under simulated Martian conditions. Detection in MARSWIT is achieved by allowing the saltating particles to impinge on a planar conducting surface normal to the flow that is connected to ground through a Keithly electrometer. The signal from the electrometer is connected to a strip chart recorder along with the analog signal from the pitot tube transducer that is used to determine the wind velocity in the tunnel. Thus, a record of wind velocity and the initiation of particle saltation is conveniently displayed together. While both positive and negative charges are produced during saltation, this method measures only the net charge; thus the charge may be either positive or negative depending upon the particles being tested, the size and size distribution of the test material, and the wind velocity. This has proven to be a very trustworthy and sensitive method of saltation threshold detection, being especially useful with the smaller sized particles which are the most difficult to observe visually.

Leach, Rodman N.↗
NASA NTRS1991

Adhesion and abrasion of surface materials in the Venusian aeolian environment

In laboratory simulations of the Venusian environment, rock and mineral 'target' surfaces struck by aeolian particles develop a thin layer of accretionary material derived from the particles' attrition debris. Accretion may be (in part) a manifestation of 'cold welding', a process well known in engineering, where bonding occurs between metals at a tribological interface. Accretion on geological materials was found to occur at all Venusian surface temperatures and for all types of materials tested. First-order variations in the amount deposited by particles are related to relative attrition susceptibilities. Second-order variations relate to properties of the particle-target interface. Variations in accretion volume are apparently independent of mineral chemistry and are only weakly dependent on crystallography. The results suggest that accretion should be a fairly universal phenomenon in areas of Venus subject to aeolian activity.

Marshall, John R.↗
NASA NTRS1991

A thermal shield concept for the Solar Probe mission

The Solar Probe spacecraft will travel to within 4 solar radii of the sun's center while performing a variety of fundamental experiments in space physics. Exposure to 2900 earth suns (400 W/sq cm) at perihelion imposes severe thermal and material demands on a solar shield system designed to protect the payload that will reside within the shield's shadow envelope or umbra. The design of the shield subsystem is a thermal/materials challenge requiring new technology development. While currently in the preproject study phase, anticipating a 1995 project start, shield preliminary design efforts are currently underway. This paper documents the current status of the mission concept, the materials issues, the configuration concept for the shield subsystem, the current configuration studies performed to date, and the required material testing to provide a database to support a design effort required to develop the shield subsystem.

Miyake, Robert N.↗
NASA NTRS1990

Techniques for capturing expert knowledge - An expert systems/hypertext approach

The knowledge-acquisition strategy developed for the Explosive Hazards Classification (EHC) Expert System is described in which expert systems and hypertext are combined, and broad applications are proposed. The EHC expert system is based on rapid prototyping in which primary knowledge acquisition from experts is not emphasized; the explosive hazards technical bulletin, technical guidance, and minimal interviewing are used to develop the knowledge-based system. Hypertext is used to capture the technical information with respect to four issues including procedural, materials, test, and classification issues. The hypertext display allows the integration of multiple knowlege representations such as clarifications or opinions, and thereby allows the performance of a broad range of tasks on a single machine. Among other recommendations, it is suggested that the integration of hypertext and expert systems makes the resulting synergistic system highly efficient.

Lafferty, Larry↗
NASA NTRS1992

Scaling Of Responses Of Composite Beams

Report describes series of experiments in which scale-model composite beams made of matrix/fiber composite materials tested to failure under combined axial compressive and bending loads. Discusses scaling effects in static large-deflection response of composite beams.

Jackson, Karen E.↗
NASA NTRS1991

High strain rate properties of angle-ply composite laminates, part 3

Angle-ply graphite/epoxy and graphite/S-glass/epoxy laminates were characterized in uniaxial tension at strain rates ranging from quasi-static to over 500 s(sup -1). Laminate ring specimens of +/-15(sub 2s), +/-22.5(sub 2s), +/-30(sub 2s), +/-45(sub 2s), +/-60(sub 2s), +/-67.5(sub 2s), and +/-75(sub 2s) degree layups were loaded under internal pressure. Results were presented in the form of stress-strain curves to failure. Properties determined included moduli, Poisson's ratios, strength, and ultimate strain. In all seven laminates for the two materials tested the modulus and strength increase with strain rate. The effect of strain rate varies with layup, being lowest for the fiber dominated +/-15(sub 2s) degree laminates and highest for the matrix dominated +/-75(sub 2s) degree laminates. The highest increments over the static values are 10 to 25 percent for the +/-15(sub 2s) degree layup and 200 to 275 percent for the +/-75(sub 2s) degree layup. Ultimate strains do not show any significant trends with strain rate. In almost all cases the ultimate strain values are within +/-20 percent of the mean value and in half of the cases the deviation from the mean are less than 10 percent.

Daniel, I. M.↗
NASA NTRS1992

Space aging of solid rocket materials

Solid rocket propellant and rocket motor components were aged in a vented container on the interior of the LDEF. This paper will present the results of aging the Improved Performance Space Motor-II/Payload Assist Module-Delta II (IPSM-II/PAM-DII) space motor components. Ballistic and mechanical properties of the space aged main propellant, igniter propellant, and ignition system were compared with similar data from preflight and ground aged samples. Mechanical properties of the composite materials and bonded joints used in the motor case, insulation, liner, nozzle, exit cone, and skirt were similarly evaluated. The space aging results will be compared to data collected in a ground based vacuum aging program on similar components. The operation of the vacuum actuated venting valve and pressure actuated resealing of the container will also be addressed. The materials tested showed no significant changes due to space aging. These results indicate that properly designed solid rocket motors can be expected to perform reliably after extended periods of exposure to a space environment.

Dean M Lester↗
NASA NTRS1990

Residual strength of repaired graphite/epoxy laminates after 5 years of outdoor exposure

The NASA Langley Research Center has sponsored research to develop generic repair techniques and processes for advanced graphite/epoxy (Gr/Ep) composites applicable to secondary structures for commercial transport aircraft. The long-term durability of such repairs is being addressed in a 10-year outdoor exposure program at the Langley Research Center. Details of the program and results of residual strength tests after 5 years of outdoor exposure are presented. Four repair methods are being evaluated. These include: (1) externally bolted aluminum-plus adhesive; (2) precured, bonded external Gr/Ep; (3) cure-in-place external Gr/Ep; and (4) cure-in-place flush Gr/Ep. Repaired specimens as well as undamaged and damaged unrepaired controls are being exposed outdoors for 1, 3, 5, 7, and 10 years. The residual tensile strength of stressed, unstressed, and fatigue specimens from each group is reported and compared with the tensile strength of baseline specimens which received no outdoor exposure. Identification of the commercial products and companies is used to describe adequately the test materials. The identification of these commercial products does not constitute endorsement, expressed or implied, of such products by the National Aeronautics and Space Administration.

Deaton, Jerry W.↗
NASA NTRS1992

Status report, June 1988 - April 1992

The Mars Mission Research Center (MMRC) is one of nine University Space Engineering Research Centers established in June 1988 by NASA's Office of Aeronautics and Space Technology to broaden the nation's engineering capability to meet the critical needs fo the civilian space program. It includes North Carolina State University (NCSU) at Raleigh and on North Carolina A&T State University at Greensboro. The goal of the Center is to focus on research and educational technologies necessary for planetary exploration, especially transportation to and from our moon and Mars. The research combines mission analysis and design, hypersonic aerodynamics, structures and controls, composite materials, and fabrications. Covered here are activities of the Center from June to April 1992. The Center supports 26 graduate students, 29 undergraduates, 27 faculty and 6 staff. An additional 88 undergraduates worked on four special projects. Three facilities at A&T were renovated and a new 7,000 square foot facility was occupied at NCSU in October 1991. Five laboratories have been developed for composite processing and fabrication facility (A&T), materials testing (A&T), weaving (NCSU), braiding (NCSU), and structures (NCSU). During the past two years, the Center added a new dimension to its program - special projects which involve analysis, design, construction, and testing. The first two projects were full-scale research models of a Mars aerobrake and the HL-20 Personnel Launch System. Both projects received considerable new coverage and appeared in national publications. Additional projects include a model of a Mars Exclusion Vehicle, an Orbiter Ejector, and a Remotely Operated Vehicle. The Orbiter Ejector is scheduled to fly on Shuttle Flight STS-47 in October 1992. Special projects have increased undergraduate student participation and provided a mechanism for more interaction between the universities, NASA centers, and industries. The faculty developed 26 new courses related to the activities of the Center. They conducted four workshops on interplanetary spacecraft, lunar/Mars aerobrakes, spacecraft controls, and aerodynamic heating. The Outreach Program developed into a significant component of the Center. Faculty and students have conducted 12 tours of facilities and given 67 lectures to schools (grade k-12) and civic organizations.

Source record↗
NASA NTRS1992

Variability in the vacuum-ultraviolet transmittance of magnesium fluoride windows

Sample window materials tested during the development of a domed magnesium fluoride detector window for the Hubble Space Telescope's Imaging Spectrograph are noted to exhibit wide variability in VUV transmittance; a test program was accordingly instituted to maximize a prototype domed window's transmittance. It is found that VUV transmittance can be maximized if the boule from which the window is fashioned is sufficiently large to allow such a component to be cut from the purest available portion of the boule.

Herzig, Howard↗
NASA NTRS1993

Testing Machine Exerts Longitudinal And Transverse Loads

Hydraulic load frame for testing materials applies both longitudinal uniaxial tension and transverse bending force simultaneously. Includes axial and transverse hydraulic actuators mounted on pivots to eliminate coupling effects between two loading modules.

Gardner, Mickey R.↗