Results for “Process settings” — Page 44

DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence S - Raw Data

Sequences S, T, and U: Upwind, No Probes (F); Upwind 2° Pitch (F); Upwind 4° Pitch (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of 0° to 180° were achieved for Sequence S, but the yaw angle remained at 0° for Sequences T and U. The blade tip pitch was 3° for Sequence S, 2° for Sequence T, and 4° for Sequence U. These three sequences were interleaved during testing because the pitch angle change was easily made by the turbine operator. The rotor rotated at 72 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to -99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. In addition to the standard 30-second campaigns, yaw sweeps were done at 7 m/s and 10 m/s for the Sequence S configuration. These 6-minute campaigns were collected while the yaw drive rotated the turbine 360° at a rate of 1°/s. The file names for these campaigns use the letter designation, followed by two digits for wind speed, followed by YSU, followed by 00.

17 WIND ENERGY↗

DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence T - Raw Data

Sequences S, T, and U: Upwind, No Probes (F); Upwind 2° Pitch (F); Upwind 4° Pitch (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of 0° to 180° were achieved for Sequence S, but the yaw angle remained at 0° for Sequences T and U. The blade tip pitch was 3° for Sequence S, 2° for Sequence T, and 4° for Sequence U. These three sequences were interleaved during testing because the pitch angle change was easily made by the turbine operator. The rotor rotated at 72 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to -99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. In addition to the standard 30-second campaigns, yaw sweeps were done at 7 m/s and 10 m/s for the Sequence S configuration. These 6-minute campaigns were collected while the yaw drive rotated the turbine 360° at a rate of 1°/s. The file names for these campaigns use the letter designation, followed by two digits for wind speed, followed by YSU, followed by 00.

17 WIND ENERGY↗

DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence U - Raw Data

Sequences S, T, and U: Upwind, No Probes (F); Upwind 2° Pitch (F); Upwind 4° Pitch (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of 0° to 180° were achieved for Sequence S, but the yaw angle remained at 0° for Sequences T and U. The blade tip pitch was 3° for Sequence S, 2° for Sequence T, and 4° for Sequence U. These three sequences were interleaved during testing because the pitch angle change was easily made by the turbine operator. The rotor rotated at 72 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to -99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. In addition to the standard 30-second campaigns, yaw sweeps were done at 7 m/s and 10 m/s for the Sequence S configuration. These 6-minute campaigns were collected while the yaw drive rotated the turbine 360° at a rate of 1°/s. The file names for these campaigns use the letter designation, followed by two digits for wind speed, followed by YSU, followed by 00.

17 WIND ENERGY↗

DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence X - Raw Data

Sequence X: Elevated RPM (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 12 m/s, and yaw angles of ±30° were obtained. The blade pitch angle was 3°. The rotor rotated at 90 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. As described in Appendix F, the hydrostatic correction derived for operation at 72 RPM was applied to these data.

17 WIND ENERGY↗

DOE OSTI2019

International Standards as Critical Enablers to Development and Diffusion of D and D Technologies - 19372

The U.S. Department of Energy's Office of Environmental Management (DOE EM) has taken a leading role in investing in the research and development (R and D) of critical technologies to support the safe and efficient decommissioning of legacy nuclear facilities. In order to facilitate the complex-wide deployment and adoption of those technologies from the laboratory to end users, and to maximize return on investment of government-sponsored R and D projects, DOE EM proactively solicits and evaluates initiatives intended to enhance achievement of these goals. One such case study emerged and involved the successful deployment of an intumescent fixative technology in support of the SRS 235-F PuFF Facility Risk Reduction Program. A detailed analysis confirmed that a critical enabler and key contributor to this effort was a deliberate, methodical approach to leverage an international, consensus-based standards organization from the onset. There is a substantial body of literature that supports the crucial role of standards in technology programs across all phases of development - from concept, to deployment, to large-scale diffusion - in other industries. Formal standards are the result of a consensual negotiation process carried out by producers, regulators, end users and other interested stakeholders in a voluntary process within standardization organizations (WTO, 2011). Therefore, standard setting is often viewed as a self-regulatory process (Gupta and Lad, 1983), and can often yield better acceptance of technologies in certain industries, particularly if those standards are further referenced in government directives and regulations. This analysis connects several theoretical concepts: information asymmetry, risk adverse markets, and technology diffusion. It is complimented by some initial, rudimentary survey results in a burgeoning academic study conducted by the author, and reinforced by the aforementioned case study on the deployment of a fixative technology at the SRS 235-F PuFF Facility. The importance of managing a holistic technology development program that focuses on not just the technical aspects of the technology itself, but the critical enablers as well, is emphasized. This effort has direct application to potentially enhancing DOE EM technology development programs across the complex. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS2005

Surveillance system and method having parameter estimation and operating mode partitioning

A system and method for monitoring an apparatus or process asset including creating a process model comprised of a plurality of process submodels each correlative to at least one training data subset partitioned from an unpartitioned training data set and each having an operating mode associated thereto; acquiring a set of observed signal data values from the asset; determining an operating mode of the asset for the set of observed signal data values; selecting a process submodel from the process model as a function of the determined operating mode of the asset; calculating a set of estimated signal data values from the selected process submodel for the determined operating mode; and determining asset status as a function of the calculated set of estimated signal data values for providing asset surveillance and/or control.

Bickford, Randall L.↗

DOE OSTI2021

Development of a framework for sequential Bayesian design of experiments: Application to a pilot-scale solvent-based CO 2 capture process

In this paper, a methodology is developed for sequential design of experiments (SDoE) for process systems and applied to a solvent-based CO 2 capture system. In this approach, the prior knowledge of the system is used to prioritize process data collection at specific operating conditions. These data are then incorporated into a Bayesian inference methodology for updating a stochastic model by refining estimations of its underlying parameters, and the updated model is then used to generate the next set of test runs. Thus, the new knowledge obtained from the data is used to guide subsequent iterations of the experimental runs, ensuring that the overall data collection is maximally informative given that most experimental campaigns, especially at pilot or higher-scale plants, are costly, time-consuming, and resource-limited. The test run objective for this work was to minimize the maximum model prediction uncertainty for key output variables, but the methodology is generic and can be readily applied to other test run objectives. This methodology is applied to an aqueous monoethanolamine (MEA) pilot plant campaign at the National Carbon Capture Center (NCCC) in Wilsonville, Alabama, USA. The SDoE framework was utilized for two iterations, while collecting 18 sets of data representing different process conditions, and this resulted in an overall average reduction in uncertainty of approximately 50% in the prediction of CO 2 capture percentage. Moreover, 11 additional data sets were obtained with variation of absorber packing height for further model validation. This work shows the capability of the SDoE framework to maximize learning given limited resources, allowing for the reduction of model uncertainty, which is of great importance for many applications including reduction of technical risk associated with scale-up and economic analysis.

20 FOSSIL-FUELED POWER PLANTS↗

NASA NTRS1980

Improvements to satellite retrieval systems. The operational perspective

Operational weather satellites are built as a series of nearly identical instruments which are flown for 5 to 7 years. Minor improvements are made during the life of the series. However, major improvements and changes in design are made with the initiation of a new series of instruments. Similarly, procedures used to process the data are characterized by frequent changes early in the life of a satellite series as user experience is gained with the new instrument. Later the changes become less frequent, both because the processing system becomes well tuned to that particular set of instruments and because, at the end of a series, resources are devoted to generating the processing system for the next set of instruments. Past and present systems are considered with emphasis on the vertical temperature profile radiometer and a procedure for deriving clear radiances in partly cloudy areas.

Mcmillin, L.↗

NASA NTRS1984

Evaluation of long-duration exposure to the natural space environment on graphite-polyimide and graphite-epoxy mechanical properties (A0175)

The primary objective of this experiment is to accumulate the needed operational data associated with the exposure of graphite-polyimide and graphite-epoxy material to the environments of space. The experiment will be mounted in two 3-in.-deep peripheral trays. Graphite-polyimide specimens will occupy 1 1/3 trays and the graphite-epoxy specimens will occupy two-thirds of a tray. The experiment approach requires two matched sets of specimens with traceable records that are maintained for materials processing and specimen quality. After fabrication, one set of each test specimen will be sectioned and structurally tested to serve as a data baseline. After the flight, the other set of specimens will undergo extensive measurements of mechanical properties for comparison with the original data baseline. Structural testing of the graphite-polyimide specimens will provide strength and elastic data in tension, compression, and shear. Transverse tension microcracking and crack propagation will be evaluated by photomicroscopy. Structural testing of the graphite-epoxy specimens will include verification of laminate, core, adhesive, and fatigue properties as applied to the design and analysis of the payload bay door. Microcracking and crack propagation will also be analyzed by photomicroscopy.

Powell, J. H.↗

NASA NTRS2012

DDS-Suite - A Dynamic Data Acquisition, Processing, and Analysis System for Wind Tunnel Testing

Wind Tunnels have optimized their steady-state data systems for acquisition and analysis and even implemented large dynamic-data acquisition systems, however development of near real-time processing and analysis tools for dynamic-data have lagged. DDS-Suite is a set of tools used to acquire, process, and analyze large amounts of dynamic data. Each phase of the testing process: acquisition, processing, and analysis are handled by separate components so that bottlenecks in one phase of the process do not affect the other, leading to a robust system. DDS-Suite is capable of acquiring 672 channels of dynamic data at rate of 275 MB / s. More than 300 channels of the system use 24-bit analog-to-digital cards and are capable of producing data with less than 0.01 of phase difference at 1 kHz. System architecture, design philosophy, and examples of use during NASA Constellation and Fundamental Aerodynamic tests are discussed.

Burnside, Jathan J.↗

NASA NTRSDate not supplied

Preparation for and Performance of a Pseudomonas aeruginosa Biofilm Experiment On Board the International Space Station

Biofilms are a problem on Earth given their ability to degrade the materials upon which they grow and due to their relevance to infections. Remarkably, 65% and 80% of infections and chronic diseases on Earth are associated with biofilms, respectively. In space, these problems' impact is higher because the crew's lives and mission success depend on nominal operation of mechanical systems. Furthermore, the isolated confined environment nature of spaceflight may increase the rates of disease transmission. In the case of the International Space Station (ISS), biofilms are an identified problem on the Environmental Control and Life Support System (ECLSS), namely on the water processor assembly (WPA). In late 2019, the Space Biofilms experiment launched towards ISS to (i) characterize the mass, thickness, morphology, and gene expression of biofilms formed in space with respect to matched Earth controls, (ii) interrogate the expression of antimicrobial resistance genes, and (iii) test novel materials as potential biofilm control strategies for future ECLSS components. For this, 288 bacterial samples were prepared prior to the launch of the Northrop Grumman CRS-12 mission from NASA's Wallops Flight Facility. The samples were integrated into the spaceflight hardware, BioServe's Fluid Processing Apparatus (FPA) packed in sets of eight in Group Activation Packs (GAP). Half of these samples were activated and terminated on orbit by NASA astronauts Jessica Meir and Christina Koch, while the remaining half were processed equivalently on Earth. The spaceflight bacterial samples of Space Biofilms returned on board SpaceX' CRS-19 Dragon spacecraft, in early 2020. We here describe the test campaign implemented to verify the experiment design and confirm it would enable us to achieve the project's scientific goals. This campaign ended with the Experiment Verification Test (EVT), from which we here present example morphology and transcriptomic results. We describe in detail the sample preparation prior to flight, including cleaning and sterilization of the coupons of six materials (SS316, passivated-SS316, lubricant impregnated surface, catheter-grade silicone with and without a nanotopography, and cellulose membrane), loading and integration of growth media, bacterial inoculum, fixative and preservative to enable experiment termination on orbit. Additionally, we describe the performance of the experiment on board the ISS, including crew activities, use of assets, temperature profile, and experiment timeline; all leading to a successful spaceflight experiment.

Pamela Flores↗

DOE OSTI2022

The interplay between vapour, liquid, and solid phases in laser powder bed fusion

The capability of producing complex, high performance metal parts on demand has established laser powder bed fusion (LPBF) as a promising additive manufacturing technology, yet deeper understanding of the laser-material interaction is crucial to exploit the potential of the process. By simultaneous in-situ synchrotron x-ray and schlieren imaging, we probe directly the interconnected fluid dynamics of the vapour jet formed by the laser and the depression it produces in the melt pool. The combined imaging shows the formation of a stable plume over stable surface depressions, which becomes chaotic following transition to a full keyhole. We quantify process instability across several parameter sets by analysing keyhole and plume morphologies, and identify a previously unreported threshold of the energy input required for stable line scans. The effect of the powder layer and its impact on process stability is explored. These high-speed visualisations of the fluid mechanics governing LPBF enable us to identify unfavourable process dynamics associated with unwanted porosity, aiding the design of process windows at higher power and speed, and providing the potential for in-process monitoring of process stability.

36 MATERIALS SCIENCE↗

NASA NTRS1981

SPAR data set contents

The contents of the stored data sets of the SPAR (space processing applications rocket) finite element structural analysis system are documented. The data generated by each of the system's processors are stored in a data file organized as a library. Each data set, containing a two-dimensional table or matrix, is identified by a four-word name listed in a table of contents. The creating SPAR processor, number of rows and columns, and definitions of each of the data items are listed for each data set. An example SPAR problem using these data sets is also presented.

Cunningham, S. W.↗

NASA NTRS1996

Variance Analysis of Unevenly Spaced Time Series Data

We have investigated the effect of uneven data spacing on the computation of delta (sub chi)(gamma). Evenly spaced simulated data sets were generated for noise processes ranging from white phase modulation (PM) to random walk frequency modulation (FM). Delta(sub chi)(gamma) was then calculated for each noise type. Data were subsequently removed from each simulated data set using typical two-way satellite time and frequency transfer (TWSTFT) data patterns to create two unevenly spaced sets with average intervals of 2.8 and 3.6 days. Delta(sub chi)(gamma) was then calculated for each sparse data set using two different approaches. First the missing data points were replaced by linear interpolation and delta (sub chi)(gamma) calculated from this now full data set. The second approach ignored the fact that the data were unevenly spaced and calculated delta(sub chi)(gamma) as if the data were equally spaced with average spacing of 2.8 or 3.6 days. Both approaches have advantages and disadvantages, and techniques are presented for correcting errors caused by uneven data spacing in typical TWSTFT data sets.

Hackman, Christine↗

NASA NTRS2005

Analytical Laboratory Science on the 2009 Mars Science Laboratory (MSL) Mission

The Odyssey Missions orbital maps of near surface ice abundance using neutron spectroscopy (Boynton et al., 2002), the Mars Exploration Rover s confirmation of aqueous processing (Squyres et al., 2004), and the Mars Express detailed infrared maps of specific mineral types that were likely formed in aqueous environments (Bibring et al., 2005) have dramatically expanded our tool set for understanding of aqueous processes on Mars. The 2009 Mars Science Laboratory is designed to extend the "follow the water" crosscutting theme of the Mars Exploration Program toward an even more detailed exploration of habitability - the potential of the Mars environment to support life. The next steps in understanding the habitability of Mars are a more detailed in situ analysis of the chemical state of elements such as C, H, O, N, S, P, Ca, and Fe that are essential for terrestrial life. Of particular interest are experiments that establish definitive mineralogy for a wider range of compounds and those that implement a more comprehensive and sensitive search for organic molecules both in the atmosphere and in surface or near surface rocks, soils, and fines. The recent reports of atmospheric methane in the Martian atmosphere make the organics exploration even more compelling. The substantial mass and power resources of MSL combined with its mobility and powerful sample acquisition and processing tools will enable it to locate a variety of near-surface samples and analyze these in some detail. NASA is presently considering the possibility of landing a second MSL rover in 2011.

Mahaffy, P. R.↗

DOE OSTI2024

Selective Deposition and Fusion of AISI 316L: An Additive Manufacturing Process for Space Environments via Direct Ink Writing and Laser Processing

Unlocking the potential of additive manufacturing (AM) for space exploration hinges on overcoming key challenges, notably the ability to manufacture or repair parts on-site during exploration missions with consideration of quality, feedstock utilization, and challenges involved in microgravity environments. While there are multiple efforts to investigate the use of existing metal AM processes such as powder bed fusion (PBF), directed energy deposition (DED), and filament-based material extrusion, each process comes with a different set of challenges in space environments. Here, in this work, we introduce a new AM method that integrates the benefits of direct ink writing (DIW) to selectively deposit metallic pastes with laser-based processing to locally debind and subsequently melt and fuse metal powder, layer by layer, enabling the manufacturing of AISI 316L samples with densities exceeding 99.0%. The impact of process parameters on single-track dimensions, surface morphology, and porosity was characterized. The efficacy of laser debinding was assessed via secondary-ion mass spectrometry, permitting the carbon content to be estimated at 0.0152%, which is safely below the acceptable limit (0.03 wt%) for AISI 316L.

36 MATERIALS SCIENCE↗

NASA NTRS1994

Assessment of the SFC database for analysis and modeling

SFC is one of the four clusters that make up the Integrated Work Control System (IWCS), which will integrate the shuttle processing databases at Kennedy Space Center (KSC). The IWCS framework will enable communication among the four clusters and add new data collection protocols. The Shop Floor Control (SFC) module has been operational for two and a half years; however, at this stage, automatic links to the other 3 modules have not been implemented yet, except for a partial link to IOS (CASPR). SFC revolves around a DB/2 database with PFORMS acting as the database management system (DBMS). PFORMS is an off-the-shelf DB/2 application that provides a set of data entry screens and query forms. The main dynamic entity in the SFC and IOS database is a task; thus, the physical storage location and update privileges are driven by the status of the WAD. As we explored the SFC values, we realized that there was much to do before actually engaging in continuous analysis of the SFC data. Half way into this effort, it was realized that full scale analysis would have to be a future third phase of this effort. So, we concentrated on getting to know the contents of the database, and in establishing an initial set of tools to start the continuous analysis process. Specifically, we set out to: (1) provide specific procedures for statistical models, so as to enhance the TP-OAO office analysis and modeling capabilities; (2) design a data exchange interface; (3) prototype the interface to provide inputs to SCRAM; and (4) design a modeling database. These objectives were set with the expectation that, if met, they would provide former TP-OAO engineers with tools that would help them demonstrate the importance of process-based analyses. The latter, in return, will help them obtain the cooperation of various organizations in charting out their individual processes.

Centeno, Martha A.↗

DOE OSTI2025

Ultraviolet Fluorescence Imaging for Photovoltaic Module Metrology: Best Practices and Survey of Features Observed in Fielded Modules

As the photovoltaics (PV) industry grows in sophistication, so must the extent to which systems are characterized. UV Fluorescence (UVF) imaging is a valuable, easy-to-perform, high-throughput, nonintrusive technique for characterizing modules in the field and in the lab. However, UVF is still a relatively new technique, and many in the PV industry are still unaware of its potential. We provide a guideline for obtaining, processing, and interpreting UVF images. We have provided a list of considerations for imaging hardware and settings, a suggested pipeline for image processing, and details on a survey of features shown in UVF images. As a result, a new database with UVF images of 7190 modules and another database curated by BrightSpot Automation are publicly available.

14 SOLAR ENERGY↗