Search NASA⌕ Search

SEARCH · Search NASA

Results for “Research Design and Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Toll-Booth Purification

NASA's Technology Application Team at Stanford Research Institute searched available information and suggested a transfer of clean-room technology employing the use of the same laminar flow techniques found in environmental control systems of clean rooms used for contamination-free assembly of precision aerospace equipment. That information, from technology originally developed by NASA and the Energy Research & Development Administration was incorporated in the design of a prototype toll booth purifier. The draft-free design includes a "diffusor", which blows clean air out the toll booth doorway, thus retarding the infiltration of contaminated air. The net effect is a decrease in the toll collector's inhalation of exhaust fumes. The Washington Department of Highways installed the prototype system in a toll booth at the Evergreen Point Bridge near Seattle. After a successful two-year test, the department now has equipped all 10 of the bridge's toll booths with the air purifiers.

Source record↗

Quick-Change Ceramic Flame Holder for High-Output Torches

Researchers at NASA's Langley Research Center have developed a new ceramic design flame holder with a service temperature of 4,000 F (2,204 C). The combination of high strength and high temperature capability, as well as a twist-lock mounting method to the steel burner, sets this flame holder apart from existing technology.

Haskin, Henry↗

NASA N+3 Subsonic Fixed Wing Silent Efficient Low-Emissions Commercial Transport (SELECT) Vehicle Study

A conceptual commercial passenger transport study was performed to define a single vehicle for entry into service in the 2030 to 2035 timeframe, meeting customer demands as well as NASA goals for improved fuel economy, NOx emissions, noise, and operability into smaller airports. A study of future market and operational scenarios was used to guide the design of an advanced tube-and-wing configuration that utilized advanced material and structural concepts, an advanced three-shaft high-bypass turbofan engine, natural laminar flow technology, and a suite of other advanced technologies. This configuration was found to meet the goals for NOx emissions, noise, and field length. A 64 percent improvement in fuel economy compared to a current state-of-the-art airliner was achieved, which fell slightly short of the desired 70 percent goal. Technology maturation plans for the technologies used in the design were developed to help guide future research and development activities.

Bruner, Sam↗

Designing Struts for the Low-Fidelity Orion Cockpit Mockup

The objective of the project was to design and construct nine struts to be installed in the low-fidelity Orion cockpit mockup (Rev F; located at NASA s Johnson Space Center in Houston, TX) as simplified representations of the existing flight designed struts designed by engineers at Lockheed Martin (the primary contractor of the Orion). The project design included: researching the existing flight designs, brainstorming design upgrades, developing three unrelated three-dimensional (3D) strut designs using Pro/Engineer Wildfire 3.0, choosing the best fit design, locating materials and their sources, implementing the chosen design, and making design modifications. The project resulted in making simple modifications to the existing struts used in the last Orion cockpit mockup. The project is relevant to NASA, because upgrades to the low-fidelity Orion cockpit mockup progresses NASA s goals of developing and testing a new spacecraft, conducting the spacecraft's first crewed mission by 2015, returning to the moon by 2020, and exploring Mars and other planets in the future.

Lucienne, Runa A.↗

Composite Overview and Composite Aerocover Overview

Materials Science Division within the Engineering Directorate tasked by the Ares Launch Vehicle Division (LX-V) and the Fluids Testing and Technology Development Branch (NE-F6) to design, fabricate and test an aerodynamic composite shield for potential Heavy Lift Launch Vehicle infusion and a composite strut that will serve as a pathfinder in evaluating calorimeter data for the CRYOSTAT (cryogenic on orbit storage and transfer) Project. ATP project is to carry the design and development of the aerodynamic composite cover or "bracket" from cradle to grave including materials research, purchasing, design, fabrication, testing, analysis and presentation of the final product. Effort consisted of support from the Materials Testing & Corrosion Control Branch (NE-L2) for mechanical testing, the Prototype Development Branch (NE-L3) for CAD drawing, design/analysis, and fabrication, Materials & Processes Engineering Branch (NE-L4) for project management and materials selection; the Applied Physics Branch (NE-LS) for NDE/NDI support; and the Chemical Analysis Branch (NE-L6) for developmental systems evaluation. Funded by the Ares Launch Vehicle Division and the Fluids Testing and Technology Development Branch will provide ODC

Caraccio, Anne↗

Implementing Geometric Surface Imperfections into Sandwich Composite Cylinder Finite Element Method Models

The buckling responses of certain cylindrical shell structures are extremely sensitive to geometric surface imperfections. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF) is conducting research to develop analysis-based buckling design recommendations. Experiments are used to verify the analysis-based factors, but the sensitivity of the test articles to geometric imperfections requires implementing as-manufactured imperfections into high-fidelity finite element method models. Data collection methods such as structured light scanning are used for all geometric surface data used in this work. Common preprocessing and visualization steps used in SBKF are discussed, and steps on how surface scans are prepared for implementation into a finite element model is described. The Python Tool for Implementing Geometric Imperfections in Reduced Structures (Py_TIGIRS), written specifically for the use with SBKF, is briefly described and uses eight functions to extract, modify, and write geometric imperfections into Abaqus input files. Results of the pre-processing methods and results from Py_TIGIRS are provided and compared for Composite Test Article (CTA) 8.2B. Excellent agreement between the visualized scan data and the FEM-extracted geometry is demonstrated. A brief example of why geometric surface imperfections are significant in nonlinear numerical analyses for thin cylinders in axial compression is provided as motivation to use tools such as Py_TIGIRS. Future development of Py_TIGIRS including expansion to structures of arbitrary geometry is planned.

Sandwich structures↗

Implementing Geometric Surface Imperfections into Sandwich Composite Cylinder Finite Element Method Models

The buckling responses of certain cylindrical shell structures are extremely sensitive to geometric imperfections. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF) is conducting research to develop analysis-based buckling design recommendations. Experiments are used to verify the analysis-based factors, but the sensitivity of the test articles to geometric imperfections requires implementing as-manufactured imperfections into high-fidelity finite element method (FEM) models. Geometry measurement methods such as structured light scanning are used for all geometric surface data used in this work. Common preprocessing and visualization steps used in SBKF are discussed, and steps of how surface scans are prepared for implementation into a finite element model is described. The Python Tool for Implementing Geometric Imperfections in Reduced Structures (Py_TIGIRS), written specifically for the use with SBKF, is briefly described and uses eight functions to extract, modify, and write geometric imperfections into Abaqus input files. Results of the preprocessing methods and results from Py_TIGIRS are provided and compared for Composite Test Articles (CTA) 8.2, 8.2B, and 8.3. Excellent agreement between the visualized scan data and the FEM-extracted geometry is demonstrated. A brief example of why geometric surface imperfections are significant in nonlinear numerical analyses for thin cylinders in axial compression is provided as motivation to use tools such as Py_TIGIRS. Future developments of Py_TIGIRS including expansion to structures of arbitrary geometry is planned.

Geometric imperfections↗

Implementing Geometric Surface Imperfections into Sandwich Composite Cylinder Finite Element Method Models

The buckling responses of certain cylindrical shell structures are extremely sensitive to geometric imperfections. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF) is conducting research to develop analysis-based buckling design recommendations. Experiments are used to verify the analysis-based factors, but the sensitivity of the test articles to geometric imperfections requires implementing as-manufactured imperfections into high-fidelity finite element method (FEM) models. Geometry measurement methods such as structured light scanning are used for all geometric surface data used in this work. Common preprocessing and visualization steps used in SBKF are discussed, and steps of how surface scans are prepared for implementation into a finite element model is described. The Python Tool for Implementing Geometric Imperfections in Reduced Structures (Py_TIGIRS), written specifically for the use with SBKF, is briefly described and uses eight functions to extract, modify, and write geometric imperfections into Abaqus input files. Results of the preprocessing methods and results from Py_TIGIRS are provided and compared for Composite Test Articles (CTA) 8.2, 8.2B, and 8.3. Excellent agreement between the visualized scan data and the FEM-extracted geometry is demonstrated. A brief example of why geometric surface imperfections are significant in nonlinear numerical analyses for thin cylinders in axial compression is provided as motivation to use tools such as Py_TIGIRS. Future developments of Py_TIGIRS including expansion to structures of arbitrary geometry is planned.

Geometric imperfections↗

Component-Based Development of CFD Software FUN3D

FUN3D, a suite of Computational Fluid Dynamics simulation and design tools developed at the NASA Langley Research Center, has undergone continuous development since the late1980s. It contains a large portion of legacy code. Extending it with new capabilities becomes increasingly difficult. To improve the extensibility and reusability, FUN3D is moving toward component-based development. New features, such as Stabilized Finite Elements, Yoga, and Sparse Linear Algebra Toolkit, are integrated into the system as components. Some existing features such as the Node-Centered Finite Volume Solver, are also being refactored to components. The integration of these components poses new requirements on the development workflow. In this paper, we describe the Continuous Integration of FUN3D to support component-based development, and discuss the tools used, the practices followed, and lessons learned during the transition from the traditional approach.

computational fluid dynamics software↗

Acoustic Modeling of Novel Over-The-Rotor Acoustic Liner Concepts Using COMSOL Multiphysics Simulation Software

This paper presents simulation predictions of novel over-the-rotor acoustic liner configurations compared with experimental data. This is a follow on to the investigation on the effect of grazing flow on grooved over-the-rotor casing treatments. The purpose of this modeling investigation stems from the determination that traditional liner modeling techniques are inadequate for nontraditional internal liner cavity geometries. A series of these expansion chamber type liner design concepts were previously developed by Glenn Research Center and tested using the Langley Research Center Normal Incidence Tube. The measured normalized impedance and absorption coefficient is compared with that obtained from the COMSOL Multiphysics® simulation. Additionally, using a parametric case study, another series of simulations were conducted to determine what additional benefits, if any, this genre of liner has to offer the acoustics community. A total of 53 permutations of this concept was investigated. The results indicate that with longer internal fins, the resonance is sifted to lower frequencies.

Acoustics↗

Low-Cost Testing in Representative Lunar Regolith Environment

Rapid prototyping and testing are key enablers of iterative designs common in early technology research and development. Testing in a dusty environment is critical to prepare the Cryogenic Magnetic Coupler for lunar operations. To enable early and iterative testing of dust mitigation concepts, a low-cost, low-fidelity representative lunar regolith environment was developed at the National Aeronautics and Space Administration (NASA) Armstrong Flight Research Center (Edwards, California). Based on preliminary testing with this test setup, a similar setup may be of interest to universities and other entities looking to develop the capability to safely test relatively small-scale components with lunar regolith simulant. The development of this lunar regolith test chamber and results from preliminary testing are presented in this paper. Also discussed are further development strategies for the potential improvement of this setup.

Scott Stebbins↗

Research and Technology Challenges for Human Data Analysts in Future Safety Management Systems

Enabling new and novel concepts of operations for Advanced Air Mobility poses an important need to evolve current safety management systems (SMS) and is posited to be realized through advances in Machine Learning (ML) Data Sciences and Artificial Intelligence. The “In-time Aviation Safety Management System” (IASMS) concept of operations supports the need to evolve today’s SMS to become more tailorable, scalable, and interoperable in response to forecasted changes expected for the future airspace system. Key to IASMS is integration of proactive and predictive ML algorithms trained to provide “in time” detection and mitigation of hazards and emergent risks through new methods and novel data types. IASMS research and technology development includes human factors design considerations for these systems to include human-system teaming, innovations in human interfaces and management of complex digital data information, human-system interaction/model-based system engineering, and verification and validation for data assurance and trust.

Chad L Stephens↗

Design of a Six-Tiltrotor Concept Vehicle for Urban Air Mobility

NASA has developed a series of aircraft concepts known as reference vehicles for urban air mobility operations to facilitate research and development, enabling system-level comparisons between design candidates. In this study, new six-tiltrotor reference vehicles with full-electric and turboelectric propulsion systems were developed using the NASA Design and Analysis of Rotorcraft (NDARC) tool. The sizing results and performance metrics of these new vehicles are presented, along with comparisons to existing reference vehicles. The turboelectric six-tiltrotor is shown to be the fastest among the turboelectric reference vehicles. Although the full-electric six-tiltrotor is not as fast as the turboelectric version, it still offers considerable speed along with increased safety compared to the tiltrotor reference vehicle.

Six-Tiltrotor↗

Update on Planetary, Lunar, & Asteroid Natural Environment Testbed (PLANET)

At ISMSE15, the Planetary, Lunar, & Asteroid Natural Environment Testbed (PLANET) was introduced as an upcoming high-fidelity, combined-effects planetary surface environment laboratory. This year, we will present an update on the facility status, describing the procurement, installation, commissioning of the chamber in Huntsville, Alabama (USA). With NASA’s push to return to the Moon through the Artemis program, there is a clear need for more high-fidelity test chambers that can replicate multiple aspects of the lunar surface, especially the fine, dusty lunar soil known as regolith. The PLANET chamber is designed to fill this gap, enabling research & development, qualification, and verification testing in a combined lunar surface environment, at an affordable price, for government, commercial/industry, and academic partners. Features include a large regolith simulant bed, low energy electron and ion sources to replicate the solar wind, full-spectrum UV and Solar simulation, and a liquid nitrogen cryogenic shroud, all in a high-vacuum environment (as low as 10^-7 mbar). PLANET’s initial focus will be on the lunar environment, but other surface environments (Martian, asteroid, etc.) are also possible to simulate. Besides the environmental instrumentation, PLANET will be equipped with specialized test systems that the Space Environmental Effects Team has developed over the past two years, including an in-situ tribometer and uniform dust distribution system. The chamber is currently being manufactured, with plans to install in May 2024. This will be followed by outfitting and commissioning. The challenges and accomplishments seen during this process will be detailed, and data from the first tests performed in PLANET will be shared with the community.

environmental testing↗

Sources and transport systems for low energy extreme of ion implantation

For the past seven years a joint research and development effort focusing on the design of steady state, intense ion sources has been in progress with the ultimate goal being to meet the two, energy extreme range needs of mega-electron-volt and 100's of electron-volt ion implanters. However, since the last Fortier is low energy ion implantation, focus of the endeavor has shifted to low energy ion implantation. For boron cluster source development, we started with molecular ions of decaborane (B{sub 10}H{sub 14}), octadecaborane (B{sub 18}H{sub 22}), and presently our focus is on carborane (C{sub 2}B{sub 10}H{sub 12}) ions developing methods for mitigating graphite deposition. Simultaneously, we are developing a pure boron ion source (without a working gas) that can form the basis for a novel, more efficient, plasma immersion source. Our Calutron-Berna ion source was converted into a universal source capable of switching between generating molecular phosphorous P{sub 4}{sup +}, high charge state ions, as well as other types of ions. Additionally, we have developed transport systems capable of transporting a very large variety of ion species, and simulations of a novel gasless/plasmaless ion beam deceleration method were also performed.

36 MATERIALS SCIENCE↗

Findings of the US Research Needs Workshop on the Topic of Fusion Power

The US Department of Energy, Office of Fusion Energy Sciences (OFES) conducted a Research Needs Workshop, referred to as ReNeW, in June 2009. The information developed at this workshop will help OFES develop a plan for US fusion research during the ITER era, roughly the next two decades. The workshop was organized in five Themes, one of which was Harnessing Fusion Power (or Fusion Power for short). The top level goal of the Fusion Power Theme was to identify the research needed to develop the knowledge to design and build, with high confidence, robust and reliable systems that can convert fusion products to useful forms of energy in a reactor environment, including a self-sufficient supply of tritium fuel. Each Theme was subsequently subdivided into Panels to address specific topics. The Fusion Power Panel topics were: fusion fuel cycle; power extraction; materials science; safety and environment; and reliability, availability, maintainability and inspectability (RAMI). Here we present the key findings of the Fusion Power Theme.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Standardized Procedure Content And Data Structure Based On Human Factors Requirements For Computer-Based Procedures

Most activities that involve human interaction with systems in a nuclear power plant are guided by procedures. Traditionally, the use of procedures has been a paper-based process that supports safe operation of the nuclear power industry. However, the nuclear industry is constantly trying to find ways to decrease the human error rate, especially the human errors associated with procedure use. Advances in digital technology make computer-based procedures (CBPs) a valid option that provides further enhancement of safety by improving human performance related to procedure use. The transition from paper-based procedures (PBPs) to CBPs creates a need for a computer-based procedure system (CBPS). A CBPS needs to have the ability to perform logical operations in order to adjust to the inputs received from either users or real time data from plant status databases. Without the ability for logical operations the procedure is just an electronic copy of the paper-based procedure. In order to provide the CBPS with the information it needs to display the procedure steps to the user, special care is needed in the format used to deliver all data and instructions to create the steps. The procedure should be broken down into basic elements and formatted in a standard method for the CBPS. One way to build the underlying data architecture is to use an Extensible Markup Language (XML) schema, which utilizes basic elements to build each step in the smart procedure. The attributes of each step will determine the type of functionality that the system will generate for that step. The CBPS will provide the context for the step to deliver referential information, request a decision, or accept input from the user. The XML schema needs to provide all data necessary for the system to accurately perform each step without the need for the procedure writer to reprogram the CBPS. The research team at the Idaho National Laboratory has developed a prototype CBPS for field workers as well as the underlying data structure for such CBPS. The objective of the research effort is to develop guidance on how to design both the user interface and the underlying schema. This paper will describe the result and insights gained from the research activities conducted to date.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Paired Straight Hearth Furnace

This factsheet describes a research project whose goals are to design, develop, and evaluate the scalability and commercial feasibility of the PSH Paired Straight Hearth Furnace alternative ironmaking process.

Fact Sheet↗