Search NASA⌕ Search

SEARCH · Search NASA

Results for “SINTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

FABRICATION AND TESTING OF MICROWAVE SINTERED SOL-GEL SPRAY-ON BISMUTH TITANATE-LITHIUM NIOBATE BASED PIEZOELECTRIC COMPOSITE FOR USE AS A HIGH TEMPERATURE (>500 deg. C) ULTRASONIC TRANSDUCER

Bismuth titanate-lithium niobate based ultrasonic transducers have been fabricated using a sol-gel spray-on deposition technique. These transducers were then tested to determine their potential as high temperature ultrasonic transducers. Fabricated transducers were capable of operating to 1000 deg. C in pulse-echo mode; however, the exposure to such extreme temperatures appears to be destructive to the transducers.

36 MATERIALS SCIENCE↗

Evolution of Triplet Paramagnetic Centers in Diamonds Obtained by Sintering of Detonation Nanodiamonds at High Pressure and Temperature

The electron paramagnetic resonance (EPR) spectra of triplet centers in detonation nanodiamonds (DNDs) and diamond single crystals of submicrometer size, synthesized from those DNDs at high pressures and temperatures, are studied. In the EPR spectra of DNDs, signals from negatively charged nitrogen- vacancy centers (NV)/sup(-) with a g factor of g{sub 1} = 4.24 and multivacancies with g{sub 2} = 4.00 are observed. The signals from (NV)/sup(-) centers disappear in the spectra of diamond single crystals, and a quintet signal with g = 4.00 is detected at the position of the signal from multivacancies. Analysis of the shape and position of the quintet’ lines showed that this ESR signal is due to the pairs of nitrogen substitution centers in diamond, separated from each other by distances not exceeding 0.7 nm, between which a strong exchange interaction takes place. A comparison of the experimental data and the simulation results allows determining the spin-Hamiltonian parameters of the exchange-coupled pairs of paramagnetic impurity nitrogen atoms.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Literature Review of Recycling Polypropylene and Polyamide 12 Powders for Selective Laser Sintering

Additive manufacturing (AM) is the creation of three-dimensional parts by adding material layer-by-layer based on two dimensional “slices” of a CAD file, without molds or tooling. AM has broken the relationship between part complexity and manufacturing cost. As a general rule, for conventional manufacturing, the more complex the part produced, the more costly its manufacturing. For example, in the production of a bracket for a satellite, moving from conventional manufacturing to AM allowed the part to be consolidated from 4 parts to just one, as well as reducing the weight of the part by 35%. A further benefit, AM can be more cost effective for small lot sizes. To illustrate, consider a case study of white board marker caps presented by Klahn et al. The cost to produce 1,000 units of a new design using SLS was about an order of magnitude lower than conventional manufacturing, as shown in Figure 1.

36 MATERIALS SCIENCE↗

Influence of Reduction Pretreatment and Methane Reforming on Nickel Solubility in YSZ Grains and Nickel Sintering within Ni-YSZ SOFC Anode Materials

Internal reforming of hydrocarbon fuels (e.g. methane or natural gas) can improve the thermal efficiency of solid oxide fuel cells (SOFC) by balancing exothermic electrochemical oxidation of H2 and CO at the anode/cathode interface with endothermic steam reforming reactions on the anode1. Generally the rate of reforming is much greater than the rate of H2 and CO oxidation leading to extensive thermal gradients across the cell that can compromise the physical integrity of the cell. Therefore, methods to control reformation activity and predict thermal gradients are needed. Computational modeling is used to predict thermal gradients and fuel conversion profiles across the cell, thus accurate and predictable methane reforming kinetics are required. Significant discrepancies in activation energy, rate expressions, and rate constants for methane reforming over nickel-yttria stabilized zirconia (Ni-YSZ) are reported in the open literature1-4. The objective of this work is to provide clarity on factors leading to discrepancies in kinetic information reported in the literature and identify potential methods to control reforming rates over NiYSZ anodes. Effects of pretreatment and reforming on Ni microstructure and activity of NiYSZ anodes for methane reforming were examined under open-circuit conditions.

03 NATURAL GAS↗