Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS CORROSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Spectral changes in Si–O–Si stretching band of porous glass network upon ingress of water

Water ingress into porous glass can induce internal stress, resulting in strains in chemical bonds of the network. For silica and silicate glasses, the position of Si–O–Si stretching mode in infrared spectroscopy is known to vary with the degree of strain in the Si–O network. Then, one could hypothesize that the stress due to water ingress could be probed with infrared spectroscopy. We tested this hypothesis using porous layers formed through aqueous corrosion on a model nuclear waste glass. The porosity and thickness of the porous layer were determined using ellipsometry. The humidity-dependent infrared spectra of the samples showed red-shifts of the Si–O–Si stretching band; however, it was difficult to deconvolute the spectral change due to variation of effective refractive index of the sample upon water ingress. Thus, it was infeasible to unambiguously determine the internal stress of porous glass network upon water ingress using the infrared spectroscopy alone.

36 MATERIALS SCIENCE↗

Microstructure and in-service degradation of baffle former bolts – in-core components of light water reactors

This report presents a microstructure evaluation of the baffle former bolt, a commercial pressurized water reactor component. Using SEM, EDS, and EBSD analysis the material was identified as AISI 316 steel with an annealed austenite microstructure. Findings include abnormal grain growth in a fraction of the grains and the absence of retained ferrite. Notable observations include an overlapping of pre- and post-irradiation deformation, including defect-free channel formation as an active deformation mechanism in the near-surface layer of BFB. Specimen surfaces, exposed to high-temperature, high-pressure water, exhibited signs of in-service corrosion degradation. EBSD and EDS analyses highlighted intergranular corrosion, possible grain boundary oxidation with depths less than 3 µm, and, unexpectedly, short cracks filled with Cr-rich oxides measuring around 5-6 µm. The presence of defect-free channels from EBSD data suggests episodes of high mechanical stresses during service. The specimens provide a potentially unique insight into the in-service degradation of NPP components, strain localization, and crack initiation processes. An intact corrosion layer reveals a complex component's in-service history. Further research is underway for a detailed analysis.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Corrosion of Silica-Based Optical Fibers in Various Environments

This research article explores the potential of optical fibers as sensors, highlighting their ability to measure various parameters such as temperature, pressure, stress, and radiation dose. The study focuses on investigating the material compatibility of optical fibers in challenging sensing environments like Gen II/II+ and advance nuclear reactors, as well as concentrated solar power (CSP) plants. Material compatibility tests were conducted to determine the feasibility of using fluorine and germanium optical fiber sensors in these environments. The study found that raw fibers were corrosion-resistant to lead bismuth eutectic at 600 °C, regardless of the coating. In molten salt environments, raw fibers were incompatible with FLiNaK but showed corrosion resistance to MgCl₂-NaCl-KCl. However, the survivability of raw fiber optics improved with a gold coating in FLiNaK. Raw fiber optics were found to be incompatible in high-temperature steam at 1200 °C and in a pressurized water reactor (PWR) at 300 °C.

Leong, Amanda (ORCID:0000000307134493)↗

Effects of Heat Treatment on Microstructure, Mechanical Properties, Corrosion Resistance and Cytotoxicity of ZM21 Magnesium Alloy as Biomaterials

The effects of heat treatment on microstructure, mechanical properties, corrosion resistance and cytotoxicity of extruded Mg-2Zn-1Mn (wt.%) alloy were investigated for biomedical application in this study. The extruded alloy was T4 treated at 510 °C for 4 h and T5 treated at 200 °C for 16 h separately. The extruded Mg-Zn-Mn alloy mainly consists of Mg{sub x}Mn{sub y} phases. After T4 treatment, the amount of Mg{sub x}Mn{sub y} phases decreases and average grain size rises from 8 to 24 μm. After T5 treatment, Mg{sub 7}Zn{sub 3} phase newly precipitates along the grain boundaries and the size of grain remains similar. Compared with the T4-treated samples, the extruded and T5-treated samples exhibit higher mechanical properties. The T5-treated samples have an ultimate tensile stress of 273 MPa and an elongation of 19.7%. On the other hand, T4-treated samples present higher corrosion resistance in electrochemical tests. The degradation rates of extruded, T4-treated and T5-treated samples are 0.44 mm/year, 0.48 mm/year and 0.50 mm/year, respectively, in Ringer’s solution at 37 ± 0.2 °C. In addition, T4-treated alloy does not induce toxicity to the L-929 cells in in vitro cytotoxicity test.

36 MATERIALS SCIENCE↗

Validation of the Modelling of Corrosion Driven Expansion in Grouted Waste-forms - 16125

One of the current preferred solutions for the disposal of Intermediate Level radioactive waste in the UK is grout encapsulation inside steel boxes for long term storage. These boxes are then to be entombed in a Geological Disposal Facility once one is available. However, both prior to and during geological disposal, waste contents can react with the water present in the encapsulant grout and begin to corrode. This corrosion product occupies a larger volume (by several hundred percent) than the original material and the corrosion occurs over the course of decades and centuries, long after the encapsulant grout has set and hardened. The expanding waste then creates stresses in the encapsulant causing both it and the surrounding box to deform and, in extreme circumstances, and after long times, for the structural integrity of the box to fail. This behaviour needs to be quantified before the box can be approved for use as any excessive deformation could lead to a loss of containment or, since the boxes are stacked on top of each other, to a significant accident in the stores. Due to the long timescales involved, physical testing of the phenomenon in full scale is impossible. Instead, a combination of chemical modelling and finite element analysis is used to predict the extent of the corrosion in the waste and its effect of the integrity of the box. There are a number of difficulties in modelling the corrosion-driven expansion and subsequent deformation of the boxes. Although the corrosion occurs over a very long time scale, the event is highly non-linear and dynamic. All of the material models, including the steel and grout are non-linear. The deformation is in the order of 10s of centimetres, well beyond the static elastic range. Finally, the components must be allowed to move relative to each other which involve a lot of part to part contacts. This means that simple static modelling, which would solve quite quickly, cannot be used. Instead a dynamic analysis code, LS-DYNA, has been used to expand the product over time to simulate the corrosion-driven expansion. This software is generally used for modelling car crashes or scenarios where waste containers have been dropped. The analyses therefore include a significant inertial component. This paper will detail the NNL's approach to modelling this long-term, quasi-static phenomenon in the dynamic, impact oriented software code LS-DYNA. It will cover the problems inherent in this approach, the errors that it creates as well as the tests and solutions that NNL worked on in order to overcome them and be confident that the solution could be validated. This work will ultimately be used to determine the maximum inventory which can be stored in each box based on the waste content and the potential extent of expansion as well as any modification that could be made to the box design or the processing streams that may improve the storage solution. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Identification and quantification of hydride phases in Zircaloy-4 cladding using synchrotron x-ray diffraction.

Zirconium hydrides precipitate in fuel cladding alloys as a result of hydrogen uptake from the high-temperature corrosion environment of light water reactors. Synchrotron X-ray diffraction was performed at room temperature on stress-relieved Zircaloy-4 cladding with two distributions of hydrides - (1) uniformly distributed hydrides across the entire cladding wall and (2) hydride rim next to the outer surface. The {delta}-hydride phase was found to be the predominant hydride phase to precipitate for hydrogen contents up to 1250 weight parts per million (wt ppm). At a higher content, about 3000 wt ppm, although {delta}-hydride is still the majority phase, a significant amount of {gamma}-hydride is also observed. At even higher hydrogen contents, in excess of approximately 6000 wt ppm, such as can occur in a highly dense hydride layer, peaks associated with the {epsilon}-hydride phase are also observed in the diffraction pattern. The volume fraction of hydrides was estimated as a function of hydrogen content using the integrated intensities of select diffraction peaks corresponding to the {alpha}-Zr matrix and the hydride phases. These estimated values agree well with calculated values from the independently measured concentrations. The results of this study indicate that hydride precipitation in Zircaloy-4 is a complex process of evolving hydride phases with increasing local hydrogen content.

08 HYDROGEN↗

In-Situ Powder-Directed Energy Process Control for Additively Manufactured Multi-Layer, Functionally Graded Components

Coatings and cladding can experience damage in harsh environments: Erosion Oxidation Delamination External mechanical damage Radiation induced damage Functionally Graded Materials (FGMs) were primarily designed to reduce thermal stress in thermal barrier coatings (TBCs), but can produce coatings which resist a variety of material damage (corrosion, surface damage, diffusion) Powder-fed DED with multiple independent feeders allows for AM FGMs, and provides robust control over process parameters to optimize microstructure and performance. FGMs have a great opportunity for applications in energy applications as a strategy to increase plant efficiency and lifetime.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Molten Salt Corrosion Tests of Additively Manufactured Stainless Steel 316H

Molten salt reactors (MSRs) have drawn considerable interest due to their favorable safety features, high thermal efficiency, and compatibility with different fuel cycles. Yet, the success of MSRs hinges critically on the performance of structural materials to be used in these aggressive molten salt environments, where corrosion and material compatibility remain primary challenges to long-term reliability. Additively manufactured (AM) nuclear structural materials prompt the use of novel geometries and compositions to enhance material performance and reduce costs of constructing MSRs. The rapid solidification conditions inherent to AM processing impart distinctive microstructural features, including cellular sub-structures, dislocation densities, residual stress, and oxide inclusions, which can influence material performance in MSR components. While the mechanical properties of AM stainless steels have been widely studied, their corrosion behavior, particularly in molten salt environments, has received far less attention. Addressing these needs, the Advanced Materials and Manufacturing Technologies (AMMT) program provides a framework for systematically evaluating how unique microstructures produced by AM processes influence the performance of these materials in these demanding environments and for developing reproducible testing workflows that can support future code qualification efforts and standards development. Bridging this knowledge gap is essential for assessing the viability of AM alloys in MSRs and informing qualification strategies. A further challenge is the absence of standardized protocols for molten salt corrosion testing. Accordingly, this report provides an account of the corrosion evaluation of AM 316H stainless steel in NaCl 2 -MgCl 2 molten salt at 550 °C, with exposure times of 100 and 500 hours. It documents the experimental procedures implemented under the AMMT program, including salt preparation, exposure protocols, and post-test characterization methods, to establish reproducibility and transparency. Importantly, the study examines AM 316H samples in the as-fabricated condition, directly reflecting the surface state most relevant to engineering applications, and compares their behavior to machine-cut surfaces. Overall, preliminary evaluations have noted that surface conditions (e.g. morphology, contamination, etc.) have a noticeable impact on the corrosion resiliency. The impact of the corrosion is difficult to detect at 100h, unless, in the case of AM 316H, the specimen surface is decontaminated. After 500 h, as-fabricated surfaces of AM and wrought 316H display evidence of general versus preferential corrosion attack, respectively. Both AM and wrought 316H machine-cut surfaces exhibit a continuous Cr depletion zone, evident of general corrosion. While the estimated extent of corrosion appears within the same order of magnitude regardless of the surface condition, it is apparent that more predictable behavior is observed on machine-cut surfaces. Nonetheless, further investigation is necessary to fully elucidate the corrosion mechanism under these conditions.

36 - MATERIALS SCIENCE↗

A Semi-Empirical Two Step Carbon Corrosion Reaction Model in PEM Fuel Cells

The cathode CL of a polymer electrolyte membrane fuel cell (PEMFC) was exposed to high potentials, 1.0 to 1.4 V versus a reversible hydrogen electrode (RHE), that are typically encountered during start up/shut down operation. While both platinum dissolution and carbon corrosion occurred, the carbon corrosion effects were isolated and modeled. The presented model separates the carbon corrosion process into two reaction steps; (1) oxidation of the carbon surface to carbon-oxygen groups, and (2) further corrosion of the oxidized surface to carbon dioxide/monoxide. To oxidize and corrode the cathode catalyst carbon support, the CL was subjected to an accelerated stress test cycled the potential from 0.6 VRHE to an upper potential limit (UPL) ranging from 0.9 to 1.4 VRHE at varying dwell times. The reaction rate constants and specific capacitances of carbon and platinum were fitted by evaluating the double layer capacitance (Cdl) trends. Carbon surface oxidation increased the Cdl due to increased specific capacitance for carbon surfaces with carbon-oxygen groups, while the second corrosion reaction decreased the Cdl due to loss of the overall carbon surface area. The first oxidation step differed between carbon types, while both reaction rate constants were found to have a dependency on UPL, temperature, and gas relative humidity.

08 HYDROGEN↗

Influence of SiC microstructure on its corrosion behavior in molten FLiNaK salt

The influence of the microstructure on the corrosion rate of three monolithic SiC samples in FLiNaK salt at 900 °C for 250 h was studied. The SiC samples, labeled as SiC-1, SiC-2, and SiC-3, had corrosion rates of 0.137, 0.020, and 0.043 mg/cm 2 h, respectively. Compared with grain size and the presence of special grain boundaries (i.e., Σ3), the content of high-angle grain boundaries (HAGBs) appeared to have the strongest influence on the corrosion rate of SiC in FLiNaK salt, since the corrosion rate increased six times as the concentration of high-angle grain boundaries increased from 19 to 32% for SiC-2 and SiC-1, respectively. The results here stress the importance of controlling the content of HAGBs during the production process of SiC.

36 MATERIALS SCIENCE↗

Modeling of concrete cracking due to corrosion process of reinforcement bars

The reinforcement corrosion in Reinforced Concrete (RC) is a major reason of degradation for structures and infrastructures throughout the world leading to their premature deterioration before design life was attained. The effects of corrosion of reinforcement are: (i) the reduction of the cross section of the bars, and (ii) the development of corrosion products leading to the appearance of cracks in the concrete cover and subsequent cover spalling. Due to their intrinsic complex nature, these issues require an interdisciplinary approach involving both material science and structural design knowledge also in terms on International and National codes that implemented the concept of durability and service life of structures. In this paper preliminary FEM analyses were performed in order to simulate pitting corrosion or general corrosion aimed to demonstrate the possibility to extend the results obtained for a cylindrical specimen, reinforced by a single bar, to more complex RC members in terms of geometry and reinforcement. Furthermore, a mechanical analytical model to evaluate the stresses in the concrete surrounding the reinforcement bars is proposed. In addition, a sophisticated model is presented to evaluate the non-linear development of stresses inside concrete and crack propagation when reinforcement bars start to corrode. The relationships between the cracking development (mechanical) and the reduction of the steel section (electrochemical) are provided. Finally, numerical findings reported in this paper were compared to experimental results available in the literature and satisfactory agreement was found.

36 MATERIALS SCIENCE↗

Understanding failure in austenitic steels: Key considerations for molten salt storage in CSP applications

Owing to their excellent properties, austenitic stainless steels are extensively used in boilers, furnaces, molten salt tanks, and other applications that are subjected to extreme mechanical loads and high-temperature conditions. Their high corrosion and creep resistance make them suitable for high-temperature operating environments. Additionally, good fatigue resistance and favorable mechanical and visual properties are essential. However, the premature failure of several components at elevated temperatures has been previously reported. Although the failure analysis of components in service is complex, processes such as cold work and welding have been identified as contributing factors to the performance degradation of these steels. This study aims to analyze the various documented failure modes and mechanisms in austenitic steels, including creep, cracking, stress relaxation cracking, and fatigue, to better understand the multi-objective design requirements for these alloys as structural materials for high-temperature molten salt tanks in Concentrating Solar Power (CSP) plants. Stabilized austenitic grades, such as AISI 347H, demonstrate superior resistance to creep and corrosion-related degradation when compared to non-stabilized grades like AISI 316L at temperatures relevant to concentrated solar power (CSP) applications. In contrast, nickel-based alloys offer enhanced corrosion resistance, albeit at a higher cost. This review underscores that creep, stress relaxation cracking, and thermo-mechanical fatigue are the predominant long-term failure risks in CSP hot tanks.

14 SOLAR ENERGY↗

LWRS Fuels Pathway: Engineering Design and Fuels Pathway - Initial Testing of the Hot Water Corrosion System

The Advanced LWR Nuclear Fuel Development R&D pathway performs strategic research focused on cladding designs leading to improved reactor core economics and safety margins. The research performed is to demonstrate the nuclear fuel technology advancements while satisfying safety and regulatory limits. These goals are met through rigorous testing and analysis. The nuclear fuel technology developed will assist in moving existing nuclear fuel technology to an improved level that would not be practical by industry acting independently. Strategic mission goals are to improve the scientific knowledge basis for understanding and predicting fundamental nuclear fuel and cladding performance in nuclear power plants, and to apply this information in the development of high-performance, high burn-up fuels. These will result in improved safety, cladding, integrity, and nuclear fuel cycle economics. To achieve these goals various methods for non-irradiated characterization testing of advanced cladding systems are needed. One such new test system is the Hot Water Corrosion System (HWCS) designed to develop new data for cladding performance assessment and material behavior under simulated off-normal reactor conditions. The HWCS is capable of exposing prototype rodlets to heated, high velocity water at elevated pressure for long periods of time (days, weeks, months). Water chemistry (dissolved oxygen, conductivity and pH) is continuously monitored. In addition, internal rodlet heaters inserted into cladding tubes are used to evaluate repeated thermal stressing and heat transfer characteristics of the prototype rodlets. In summary, the HWCS provides rapid ex-reactor evaluation of cladding designs in normal (flowing hot water) and off-normal (induced cladding stress), enabling engineering and manufacturing improvements to cladding designs before initiation of the more expensive and time consuming in-reactor irradiation testing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A General Overview of Cathodic Protection in Reinforced Concrete

Corrosion of reinforcement steel in concrete is a prevalent issue in infrastructures worldwide, with the direct costs of repair estimated to be $1 trillion annually. Treatment options are complicated by the concrete’s role in the corrosion process. Ordinary, modern-day cement is so alkaline that it maintains a thick passive layer on the steel surface, reducing corrosion to inconsequential rates. However, environmental contaminants in the form of carbon dioxide or chlorides may cause a breakdown in the passive layer, exposing the steel surface to corrosion. Galvanic cells will be free to form due to potential differences along the rebar, and anode sites will create dissolved iron ions that cannot travel far through the still concrete. Thus, rust products will accumulate directly onto the steel/concrete interface. Iron oxides have a much higher volume relative to steel, and even a miniscule amount of rust can produce enough volumetric stress to cause cracking, spalling and delamination of the surrounding concrete, increasing the risk of structural failure. Safeguards and inhibiting technology exist to limit the chances of corrosion initiation by either species, but cracking of the concrete cover and gradual accumulation of contaminants means that corrosion is unavoidable in certain environments and will initiate, given enough time.

36 MATERIALS SCIENCE↗

Microstructure and corrosion behavior of cast Fe-B alloys dipped into liquid zinc bath

The corrosion behavior of cast Fe-B alloys in a liquid zinc bath was examined. As a result, the as-cast Fe-3.5B alloy displays the best corrosion resistance in all tested specimens owing to its netlike structure of eutectic Fe{sub 2}B against the liquid zinc. XRD and EDS results indicate that the main phases in the corrosion layer are determined to be {delta}, {zeta} and {eta} from the matrix to the zinc zone, respectively. The corrosion process is controlled by the diffusion of zinc atoms and the dissolution mechanism. According to the observations, only three steps occur in the whole dissolution process: the preferential dissolution of {alpha}-Fe, the formation of intermetallic compounds, and the spalling of Fe{sub 2}B caused by cracks that mainly result from the internal stress produced by Fe/Zn phase transformation. The continuous netlike Fe{sub 2}B phase delays the further reaction of Fe/Zn and hinders the diffusion of zinc atoms between the substrate and liquid zinc effectively, improving corrosion resistance of Fe-B alloy in comparison with 1Cr18Ni9Ti stainless steel.

36 MATERIALS SCIENCE↗

Degradation in PV Encapsulation Strength of Attachment: An Interlaboratory Study Towards a Climate-Specific Test

Reduced strength of attachment of the encapsulant resulting from the outdoor environment, including ultraviolet (UV) radiation, may decrease photovoltaic (PV) module lifetime by enabling widespread corrosion of internal components. To date, few studies exist showing how the adhesion of PV components varies with environmental stress. We have conducted an interlaboratory experiment to provide an understanding that will be used to develop climatic specific module tests. Factors examined in the study included the UV light source (lamp type), temperature, and humidity to be proposed for use in accelerated aging tests. A poly (ethylene-co-vinyl acetate) (EVA) formulation often used in veteran PV installations was studied using a compressive shear test - to quantify the strength of attachment at the EVA/glass interface. Replicate laminated glass/polymer/glass coupon specimens were weathered at 12 institutions using a variety of indoor chambers or field aging. Shear strength, shear strain, and toughness were measured using a mechanical load-frame for the compressive shear test, with subsequent optical imaging and electron microscopy of the separated surfaces.

14 SOLAR ENERGY↗

Sodium Exposure Tests of A709 Steel (FY2020 Progress Report)

Sodium exposure tests were conducted on the first commercial heat, H58776 of A709 steel. Six different processing and heat treatment conditions were investigated, including three processing conditions, namely, Argon-Oxygen-Decarburization (AOD), Electro-slag Remelting (ESR), and Electro-slag Remelting with subsequent homogenization (HOMO), and two heat treatment conditions, i.e. solution annealing at 1100°C (SA1100°C) or 1150°C (SA1150°C). Specimens of AOD-SA1100°C, AOD-SA1150°C, ESR-SA1100°C, ESR-SA1150°C, HOMO-SA1100°C, and HOMO-SA1150°C were tested in sodium at 650°C and for times up to 10,152 h. Specimens in the AOD-SA1100°C and AOD-SA1150°C conditions were also tested in sodium at 550 and 600°C. Parallel thermal aging experiments were carried out for comparison with sodium exposure tests to separate the thermal and sodium effects. It was found that A709 H58776 generally showed a weight loss after sodium exposures at 650°C except a few data points of the ESR-SA1100°C specimens. The corrosion rate showed large variations in the initial stage and decreased with increasing exposure time. Long-term exposure tests are needed to determine its steady-state corrosion rate. The AOD-SA1100°C and HOMO-SA1100°C specimens showed similar tensile responses after thermal or sodium exposures at 650°C. The yield stress increased, the ultimate tensile strength decreased, and the uniform and total elongations were reduced after thermal or sodium exposures. A longer exposure time had a minimal effect on the tensile strength but further reduced the tensile ductility. The sodium-exposed specimens had higher tensile strength than the thermally-aged specimens. In contrast, the ESR-SA1100°C specimens showed an increase in the yield stress and the ultimate tensile strength after thermal or sodium exposures at 650°C and ~10,000 h. The AOD-SA1150°C and ESR-SA1150°C specimens showed similar tensile behavior after thermal or sodium exposures at 650°C.Thermal or sodium exposures at 650°C increased the yield stress, decreased the ultimate tensile strength, and reduced uniform and total elongations. There were minimal differences in tensile properties between the sodium-exposed and thermally-aged specimens after an ~3000 h exposure. After an exposure for ~10,000 h the sodium-exposed specimens showed higher yield stress and ultimate tensile strength and lower uniform and total elongations than the thermally-aged specimens. For the HOMO-SA1150°C specimens, thermal or sodium exposures at 650°C significantly increased the yield stress but had a minimal effect on the ultimate tensile strength. Both uniform and total elongations were significantly reduced at an exposure time of ~3,000 h, and they were further reduced after an exposure of ~10,000 h. The sodium-exposed specimens had lower tensile ductility than the thermally-aged specimens. Before exposure, the stress-strain curves of the specimens in all six processing-heat treatment conditions showed serrations indicating the dynamic aging effect at 650°C. Thermal aging or sodium exposures at 650°C after ~10,000 h completely removed the serrations of the flow curves in A709 H58776, indicating strong precipitation during thermal or sodium exposures. Longer-term sodium exposure tests are needed to determine the steady-state corrosion rates in sodium for A709 H58776 and fully understand the influence of sodium exposures on its mechanical performance.

36 MATERIALS SCIENCE↗

Corrosion Behavior of Zinc Cold Spray Coatings in a Simulated Natural Gas Environment Containing H2O, CO2, and H2S

The natural gas transmission pipeline network in the U.S. consists of approximately 300,000 miles, is made mainly of carbon steel, and was installed in the 1950s and 1960s. Understanding the pipeline steel behavior in natural gas will inform new pipeline designs and repurposing of existing pipelines. Sulfide stress cracking (SSC) is a problem for steel pipelines transporting natural gas or CO2 containing partial pressures of H2S higher than 0.3 kPa (0.05 psi). Therefore, the objective of this work is to mitigate internal corrosion in steel pipelines transporting natural gas containing H2S using cold spray coatings.

Belarbi, Zineb↗