Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

THERMAL/STRUCTURAL ANALYSIS OF THE AXION QUANTUM METROLOGY CAVITY AND ITS COMPONENTS

This research was centered around maximizing the capability to cool dielectric material within a containment unit, or Photonic Band Gap (PBG) cavity, designed for detecting axion dark matter and identifying the unit’s thermal properties. There are multiple types of PBG cavities, but the latest version that axion researchers wish to use has been theorized to contain possible issues related to its thermal properties. Thermal conductivity is an issue with the dielectric material because it is made from alumina which is highly insulative. This is important since the research is being done in a cryogenic environment and the thermal noise affects the quantum bit used for detecting the axion to photon conversion process. Therefore, any improvements to this unit should be justified and implemented but are not entirely limited to thermal contact related aspects of PBG cavities. A prospect of using sapphire in place of alumina also exists, but this is a more expensive, less tested, and more elusive material to justify the creation of a full dielectric structure out of sapphire. Thermal aspects of the cavity were analyzed using finite element method (FEM) and an experiment designed to test different thermal joint materials. FEM was used to check the contraction of the cavity during cooling, the contact quality between the dielectric material and cavity wall, theheat flow rate through the assembly, and helps visualize the cavity’s reaction to different design changes. A simple comparison between thermal conductivity curves justified the usage of sapphire over alumina from a thermal property point of view. Thus, the method of experimentation had an additional dielectric material, sapphire, to test with and compare to alumina. The thermal test identified which material is best to use for a thermal joint but also simultaneously found the conductance of the joint and dielectric material as well as an estimate for what the temperature is inside the larger scale cavity since a thermometer cannot be placed inside the PBG when it cools. Initially, the cavity simulation was tested for structural deformation properties and stress distribution since it is made of copper which contracts heavily in comparison to most other materials. The reduction in volume of the cavity was less than anticipated which gave more room for a possible usage of a modified thermal joint for additional contact area and higher conductivity.

43 PARTICLE ACCELERATORS↗

Development of Lightweight Structural Materials with Improved Properties for Fission Batteries

The notion of a “fission battery” conveys a vision focused on realizing very simple “plug-and-play” nuclear systems that can be integrated into a variety of applications requiring affordable, reliable energy in the form of electricity and/or heat and function without operations and maintenance staff. Fission batteries require lightweight structural materials to increase their mobility, and the lightweight materials must demonstrate structural resilience under various conditions. The objective of this work is to develop lattice structured lightweight structural material featuring a good combination of mechanical properties using advanced modeling and simulation together with an advanced additive manufacturing technique such as laser powder bed fusion. The preliminary results show that different lattice structures and types can be successfully meshed using nTopology software, and the lattice structure data can be successfully transformed to Multiphysics Object-Oriented Simulation (MOOSE) Environment input. Finite Element Analysis (FEA) displays that, at macro/engineering scale simulation, the weight saving design has an obvious effect on tensile behavior such as effective elastic modulus and yield stress. The novel approaches of this work are (1) development of lattice structures for improved mechanical properties using advanced simulation and modeling techniques; and (2) model predictions of the mechanical properties (e.g., strength and stress distribution) of macroscopic materials in order to preliminarily select a lattice structure for additive manufacturing.

36 MATERIALS SCIENCE↗

COMPUTER-AIDED LATTICE DESIGN AND ADVANCED MODELING FOR THE DEVELOPMENT OF LIGHTWEIGHT STRUCTURAL MATERIALS

The notion of a “fission battery” conveys a vision focused on realizing very simple “plug-and-play” nuclear systems that can be integrated into a variety of applications requiring affordable, reliable energy in the form of electricity and/or heat and function without operations and maintenance staff. Fission batteries require lightweight structural materials to increase their mobility, and the lightweight materials must demonstrate structural resilience under various conditions. The objective of this work is to develop lattice structured lightweight structural material featuring a good combination of mechanical properties using advanced modeling and simulation together with an advanced additive manufacturing technique such as laser powder bed fusion. The preliminary results show that different lattice structures and types can be successfully meshed using nTopology software, and the lattice structure data can be successfully transformed to Multiphysics Object-Oriented Simulation (MOOSE) Environment input. Finite Element Analysis (FEA) displays that, at macro/engineering scale simulation, the weight saving design has an obvious effect on tensile behavior such as effective elastic modulus and yield stress. The novel approaches of this work are (1) development of lattice structures for improved mechanical properties using advanced simulation and modeling techniques; and (2) model predictions of the mechanical properties (e.g., strength and stress distribution) of macroscopic materials in order to preliminarily select a lattice structure for additive manufacturing.

36 MATERIALS SCIENCE↗

Development of Lightweight Structural Materials with Improved Properties for Fission Batteries

The notion of a “fission battery” conveys a vision focused on realizing very simple “plug-and-play” nuclear systems that can be integrated into a variety of applications requiring affordable, reliable energy in the form of electricity and/or heat and function without operations and maintenance staff. Fission batteries require lightweight structural materials to increase their mobility, and the lightweight materials must demonstrate structural resilience under various conditions. The objective of this work is to develop lightweight structural material featuring a good combination of mechanical properties using advanced modeling and simulation together with an advanced additive manufacturing technique such as laser powder bed fusion. The preliminary results show that different lattice structures and types can be successfully meshed using nTopology software, and the lattice structure data can be successfully transformed to Multiphysics Object-Oriented Simulation Environment (MOOSE) input. Finite Element Analysis (FEA) displays that, at macro/engineering scale simulation, the weight saving design has an obvious effect on tensile behavior such as effective elastic modulus and yield stress. The novel approaches of this work are (1) development of optimized lattice structures for improved mechanical properties using advanced simulation and modeling techniques; and (2) model predictions of the mechanical properties (e.g., strength and stress distribution) of macroscopic materials in order to preliminarily select a lattice structure for additive manufacturing.

36 MATERIALS SCIENCE↗

Microwave Debinding of Ceramics Produced by Additive Manufacturing

Microwave-assisted debinding offers an innovative approach to processing 3D-printed engineering ceramics. Ceramic parts produced with photopolymer-based additive manufacturing techniques require thermal debinding to remove polymers that bind ceramic particles during the printing process. Microwave-assisted debinding significantly reduces processing times and offers energy savings over conventional thermal treatments due to higher heating rates and more uniform heating. Finite-element modeling of the debinding process allows for the optimization and prediction of temperature distribution, stress development, and potential defects, leading to improved process control and material quality.

36 - MATERIALS SCIENCE↗

Mathematical models as tools for probing long-term safety of CO2 storage

Subsurface reservoirs being considered for storing CO{sub 2} include saline aquifers, oil and gas reservoirs, and unmineable coal seams (Baines and Worden, 2004; IPCC, 2005). By far the greatest storage capacity is in saline aquifers (Dooley et al., 2004), and our discussion will focus primarily on CO{sub 2} storage in saline formations. Most issues for safety and security of CO{sub 2} storage arise from the fact that, at typical temperature and pressure conditions encountered in terrestrial crust, CO{sub 2} is less dense than aqueous fluids. Accordingly, CO{sub 2} will experience an upward buoyancy force in most subsurface environments, and will tend to migrate upwards whenever (sub-)vertical permeable pathways are available, such as fracture zones, faults, or improperly abandoned wells (Bachu, 2008; Pruess, 2008a, b; Tsang et al., 2008). CO{sub 2} injection will increase fluid pressures in the target formation, thereby altering effective stress distributions, and potentially triggering movement along fractures and faults that could increase their permeability and reduce the effectiveness of a caprock in containing CO{sub 2} (Rutqvist et al., 2008; Chiaramonte et al., 2008). Induced seismicity as a consequence of fluid injection is also a concern (Healy et al., 1968; Raleigh et al., 1976; Majer et al., 2007). Dissolution of CO{sub 2} in the aqueous phase generates carbonic acid, which may induce chemical corrosion (dissolution) of minerals with associated increase in formation porosity and permeability, and may also mediate sequestration of CO{sub 2} as solid carbonate (Gaus et al., 2008). Chemical dissolution of caprock minerals could promote leakage of CO{sub 2} from a storage reservoir (Gherardi et al., 2007). Chemical dissolution and geomechanical effects could reinforce one another in compromising CO{sub 2} containment. Additional issues arise from the potential of CO{sub 2} to mobilize hazardous chemical species (Kharaka et al., 2006), and from migration of the large amounts of brine that would be mobilized by industrial-scale CO{sub 2} injection (Nicot et al., 2008; Birkholzer et al., 2008a, b).

54 ENVIRONMENTAL SCIENCES↗

Evaluation of the Pressing Characteristics of Commercially Pure Titanium Using an Instrumented Double Acting Die

With recent advances in synthesizing titanium powder by low-cost routes, there has been growing interest in identifying process/material conditions that overcome the powder compaction problems typically found with this reactive metal. The use of instrumented dies in studying the cold pressing process for commercial iron and steel powders has provided greater insight into the complex phenomena that occur and may be used to evaluate constitutive relations that describe the compaction process. Nevertheless, little work has been conducted on the special, more problematic case of reactive metal powders such as titanium. An instrumented die was developed that allows die wall friction to be characterized and the radial stress distribution along the die wall and throughout the compact to be monitored. As will be presented, this tool has been used to investigate titanium compaction and to draw comparisons with results obtained on a baseline commercial iron powder. Both sets of data were systematically collected using various powder/die lubrication combinations.

36 MATERIALS SCIENCE↗

Stress and strain relaxation in magnesium AZ31 rolled plate: In-situ neutron measurement and elastic viscoplastic polycrystal modeling

Continuous mechanical tests with strain holds (stress relaxation) and with stress holds (strain relaxation) are performed simultaneously with in-situ neutron measurements to analyze the mechanisms of stress and strain relaxation in Mg AZ31 rolled plate. A dislocation activity based constitutive model, accounting for internal stress statistical distributions, is proposed and implemented into an elastic viscoplastic self-consistent (EVPSC) framework to simultaneously describe both stress and strain relaxation. The model captures the experimental data in terms of macroscopic stress strain curves, evolution of stress and strain during holding, as well as evolution of the internal elastic strains. Model results indicate that the magnitude of the stress relaxed during strain holding is dependent on both, the magnitude of the flow stress and the spread of the resolved shear stress distribution. The magnitude of strain accumulated during stress holding is, on the other hand, dependent on the magnitude of the hardening rate and on the spread of the resolved shear stress distribution. Furthermore, the internal elastic strains are directly correlated with the stress state, and hence the stress relaxation during strain holds has a greater influence on the lattice strains than strain relaxation during stress holds.

36 MATERIALS SCIENCE↗

Temperature-time distribution and thermal stresses on the RTG fins and shell during water cooling

Radioisotope thermoelectric generator (RTG) packages designed for space missions generally do not require active cooling. However, the heat they generate cannot remain inside of the launch vehicle bay and requires active removal. Therefore, before the Shuttle bay door is closed, the RTG coolant tubes attached to the heat rejection fins must be filled with water, which will circulate and remove most of the heat from the cargo bay. There is concern that charging a system at initial temperature around 200 C with water at 24 C can cause unacceptable thermal stresses in the RTG shell and fins. A computer model is developed to estimate the transient temperature distribution resulting from such charging. The thermal stresses resulting from the temperature gradients do not exceed the elastic deformation limit for the material. Since the simplified mathematical model for thermal stresses tends to overestimate stresses, it is concluded that the RTG can be cooled by introducing water at 24 C to the initially hot fin coolant tubes while the RTG is in the Shuttle cargo bay.

Turner, R. H.↗

Distribution of Reynolds stress carried by mesoscale variability in the Antarctic Circumpolar Current

Satellite altimeter data collected by the Geosat Exact Repeat Mission were used to investigate turbulent stress resulting from the variability of surface geostrophic currents in the Antarctic Circumpolar Current. The altimeter measured sea level along the subsatellite track. The variability of the along-track slope of sea level is directly proportional to the variability of surface geostrophic currents in the cross-track direction. Because the grid of crossover points is dense at high latitudes, the satellite data could be used for mapping the temporal and spatial variability of the current. Two and a half years of data were used to compute the statistical structure of the variability. The statistics included the probability distribution functions for each component of the current, the time-lagged autocorrelation functions of the variability, and the Reynolds stress produced by the variability. The results demonstrate that stress is correlated with bathymetry. In some areas the distribution of negative stress indicate that eddies contribute to an acceleration of the mean flow, strengthening the hypothesis that baroclinic instability makes important contributions to strong oceanic currents.

Johnson, Thomas J.↗

Determination of Stress Intensity Factor Distributions for "Interface" Cracks in Incompressible, Dissimilar Materials

The present study was undertaken in order to develop test methods and procedures for measuring the variation of the stress intensity factor through the thickness in bimaterial specimens containing cracks within and parallel to the bond line using the frozen stress photoelastic method. Since stress freezing materials are incompressible above critical temperature, and since thick plates are to be employed which tend to produce a state of plane strain near the crack tip, the interface near tip fracture equations reduce to the classic form for homogeneous materials. Moreover, zero thickness interfaces do not exist when materials are bonded together. It was decided early on that it would be important to insure a uniform straight and accurate crack tip region through the thickness of the body to reduce scatter in the SIF distribution through the thickness. It was also observed that rubberlike materials which were desired to be modeled exhibited significant tip blunting prior to crack extension and that some blunting of the tip would provide a more realistic model. It should be noted that, in normal stress freezing photoelastic work, it is considered good practice to avoid utilizing data near bond lines in photoelastic models due to the bond line stresses which inevitably develop when two parts are bonded together. Thus, the present study involves certain exploratory aspects in deviating from standard practice in stress freezing work. With the above ideas in mind, several different test methods were investigated and are described in the following sections and appendices. The geometry selected for the program was a thick, edge cracked specimen containing a bond line.

Smith, C. W.↗

A Study of Temperature Distribution and Thermal Stresses in a Hot Rock Due to Rapid Cooling

Thermal stresses may be induced in a hot dry rock when a cold fluid is injected in the well. To study this problem, we look at the thermoelastic response of a hot rock that is suddenly cooled. The cooling is assumed to be either at a constant temperature or at a constant heat flux per unit depth. Our approach is to nondimensionalize the equations and perform a parametric study and look at the temperature distribution and the induced-thermal stresses. The results indicate that depending on the extent of cooling and the cooling time, thermal stresses can be induced. Numerical simulations on sandstone, with an initial uniform temperature of 473 K, are also carried out. The results show that if the cooling is due to the surface temperature maintained at 463 K (10 °C lower than the initial temperature of the hot rock), thermal stresses that are larger than the rock tensile strength could be induced. When the cooling is due to a constant surface heat flux, this temperature can be reached after about 777 days of cooling with a minimum value of a heat flux of -20 W/m.

Tran, Phuoc↗

Slip band characteristics in the presence of grain boundaries in nickel-based superalloy

Shear strain profiles along slip bands in a modified Rolls-Royce nickel superalloy (RR1000) were analyzed for a tensile sample deformed by 2%. The strain increased with distance away from a grain boundary (GB), with maximum shear strain towards the center of the grain, indicating that dislocation nucleation generally occurred in the grain interior. The strain gradients in the neighborhood of the GBs were quantified and generally correlated with rotation about the active slip system line direction. This leads to an ability to determine the active slip system in these regions. The dislocation spacing and pileup stresses were inferred. The dislocation spacing closely follows an Eshelby analytical solution for a single ended pileup of dislocations under an applied stress. The distribution of pileup stress values for GBs of a given misorientation angle follows a log-normal distribution, with no correlation between the pileup stress and the GB misorientation angle. Furthermore, there is no observed correlation between various transmissivity factors and slip band pileup stress. Hence it appears that the obstacle strength of any of the observed GBs is adequate to facilitate the dislocation pileups present in the slip bands. However, slip band transmission does correlate with transmissivity factors, with the current study focusing on the Luster and Morris m’-factor. Observation of strain profiles of transmitted bands indicate dislocation nucleation locations.

36 MATERIALS SCIENCE↗

The craton - Its effect on the distribution of seismicity and stress in North America

The gross distribution of seismicity in North America suggests the interior platform and shield provinces are relatively stable and significantly affect the intraplate stress field. Focal mechanisms and in-situ stress measurements indicate the cratonic areas of North America must be relatively immobile with respect to the eastern and western portions of the continent. Simple kinematic models are presented to illustrate the importance of the craton in any attempt to explain the general pattern of intraplate stress and seismicity in North America.

Wesnousky, S. G.↗

Atomistic simulations of nanowelding of single-crystal and amorphous gold nanowires

The mechanism and quality of the welding of single-crystal (SC) and amorphous gold nanowires (NWs) with head-to-head contact are studied using molecular dynamics simulations based on the second-moment approximation of the many-body tight-binding potential. The results are discussed in terms of atomic trajectories, slip vectors, stress, and radial distribution function. Simulation results show that the alignment for the amorphous NWs during welding is easier than that for the SC NWs due to the former's relatively stable geometry. A few dislocations nucleate and propagate on the (111) close-packed plane (slip plane) inside the SC NWs during the welding and stretching processes. During welding, an incomplete jointing area first forms through the interactions of the van der Waals attractive force, and the jointing area increases with increasing extent of contact between the two NWs. A crystallization transition region forms in the jointing area for the welding of SC-amorphous or amorphous-SC NWs. With increasing interference, an amorphous gold NW shortens more than does a SC gold NW due to the former's relatively poor strength. The pressure required for welding decreases with increasing temperature.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗