Spin-Tunnel Tests of Airplane Models with Extreme Variations in Mass Distribution Along the Three Body Axes
Explore the source record for details and available documents.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
The effect of various vertical tail arrangements upon the stability and control characteristics of an XP-62 fighter model was investigated. Rudder-free yaw characteristics with take-off power and flaps deflected were satisfactory after dorsal fin modifications. Directional stability was obtained with all modified vertical tails. Satisfactory rudder effectiveness resulted partly because the dual-rotation propellers produced no asymmetric yawing moments. Pedal forces in sideslips were undesirably large but may be easily reduced.
An investigation was made of the static longitudinal stability, and control and stall characteristics of XBTK-1 dive bomber. Results indicate that the longitudinal stability will probably be satisfactory for all contemplated flight conditions at the rear-most CG location with elevator both fixed and free. Power effects were small. Sufficient elevator control will be available to trim in any flight condition above the ground. Increasing the slotted flap deflection above 30 degrees only slightly increased the max. lift coefficient.
Explore the source record for details and available documents.
The topics covered include the following: a test of a Space Shuttle model with various base enhancements intended to help reduce the drag of the Shuttle in the landing configuration; further tests conducted using a Shuttle model to explore base drag improvement techniques; testing of parafoils having different airfoil shapes and line lengths; a study of ground effects on a Shuttle model; and three dimensional velocity profiles in the wake aft of the Space Shuttle were determined to study the effects of wake velocities on the Orbiter drag chute.
Tests were made of a large-scale tilt-wing deflected-slipstream VTOL airplane with blowing-type BLC trailing-edge flaps. The model was tested with flap deflections of 0 deg. without BLC, 50 deg. with and without BLC, and 80 deg. with BLC for wing-tilt angles of 0, 30, and 50 deg. Included are results of tests of the model equipped with a leading-edge flap and the results of tests of the model in the presence of a ground plane.
An investigation was made to determine the lifting effectiveness and flow requirements of blowing over the trailing-edge flaps and ailerons on a large-scale model of a twin-engine, propeller-driven airplane having a high-aspect-ratio, thick, straight wing. With sufficient blowing jet momentum to prevent flow separation on the flap, the lift increment increased for flap deflections up to 80 deg (the maximum tested). This lift increment also increased with increasing propeller thrust coefficient. The blowing jet momentum coefficient required for attached flow on the flaps was not significantly affected by thrust coefficient, angle of attack, or blowing nozzle height.
Inlet-performance and external-drag-coefficient characteristics are presented without analysis. Effects are shown of variations of fuselage boundary-layer diverter profile, bleed-surface porosity, bleed-exit area, and inlet ramp, and lip angle.
Flutter of an aeroelastic structure is potentially destructive aeroelastic instability. This phenomenon has motivated research within the aeroelastic community to develop methods that can accurately predict aeroelastic instabilities. The Flutterometer method used herein, and as developed by NASA DFRC, is based upon the mu method which has been coupled with wavelet filtering processes in estimating aeroelastic models from flight data. The approach leads to a methodology to predict the occurrence of flutter boundaries, and may prove to reliably predict flutter boundaries during flight tests. An analytical model is used as the first estimate of the aeroelastic structural dynamics, and uncertainty operators are introduced into the system to model variations between the theoretical system and the physical system. The modelling uncertainties are then updated from experimental data. Although the model used did not work well with this particular experiment, a sensitivity analysis was additionally performed and improvements suggested.