Search NASA⌕ Search

SEARCH · Search NASA

Results for “Well Test Data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

High pressure shock tube ignition delay time measurements during oxy-methane combustion with high levels of CO 2 dilution

For this study, ignition delay times and methane species time-histories were measured for methane/O 2 mixtures in a high CO 2 diluted environment using shock tube and laser absorption spectroscopy. The experiments were performed between 1300 K and 2000 K at pressures between 6 and 31 atm. The test mixtures were at an equivalence ratio of 1 with CH 4 mole fractions ranging from 3.5% -5% and up to 85% CO 2 with a bath of argon gas as necessary. The ignition delay times and methane time histories were measured using pressure, emission, and laser diagnostics. Predictive ability of two literature kinetic mechanisms (GRI 3.0 and ARAMCO Mech 1.3) was tested against current data. In general, both mechanisms performed reasonably well against measured ignition delay time data. The methane time-histories showed good agreement with the mechanisms for most of the conditions measured. A correlation for ignition delay time was created taking into the different parameters showing that the ignition activation energy for the fuel to be 49.64 kcal/mol. Through a sensitivity analysis, CO 2 is shown to slow the overall reaction rate and increase the ignition delay time. To the best of our knowledge, we present the first shock tube data during ignition of methane/CO 2 /O 2 under these conditions. In conclusion, current data provides crucial validation data needed for development of future kinetic mechanisms.

42 ENGINEERING↗

Brine stability study

This is a study of the brine formulations that we were using in our testing were stable over time. The data includes charts, as well as, all of the original data from the ICP-MS runs to complete this study.

15 GEOTHERMAL ENERGY↗

Regulatory Gap Analysis of Select NUREG-0800 Chapters for Applicability to Molten Salt Reactors

The past licensing approach for advanced reactors was based on adapting the current LWR-based NRC process that exists today to the advanced reactor concept. This is the approach used by advanced technologies such as the Pebble Bed Reactor licensing application, the Clinch River Breeder Reactor licensing application, and more recently the NuScale licensing application. Current Standard Review Plan (SRP) guidance for large LWRs is available in NUREG-0800, Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants: Light Water Reactor (LWR) Edition. However, the SRP is cumbersome to apply to liquid-fueled molten salt reactor (MSR) technologies. Therefore, a thoughtful licensing approach for MSRs is necessary.This report documents for DOE-NE an additional regulatory gap analysis of select chapters from the LWR SRP to further inform a generic nonpower MSR test program. Although the review process outlined in NUREG-0800 is LWR-specific, the plant functions and processes to be reviewed will be similar for the MSR. Therefore, a well-planned nonpower MSR test program can provide the performance data needed to better facilitate the eventual commercial-sized MSR review. The LWR SRP chapters dealing with the reactor, reactor coolant, engineered safety features, auxiliary systems, and waste management systems were reviewed.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

PIPII cryoplant non thermal cycling updates

The Proton Improvement Plan-II (PIP-II) is a crucial upgrade to the Fermilab accelerator complex, featuring a new 800-MeV Superconducting Radio-Frequency (SRF) linear accelerator (LINAC) with 23 cryomodules operating at 2K. The LINAC thermohydraulic conditions are satisfied by the cryogenic subsystems: Cryogenic Distribution System (CDS), a helium refrigerator cold box (CB), a warm compression station (WCS) and a helium recovery system (RSYS). The accelerator has a strict requirement of non-thermal cycling of the LINAC cryomodules during planned and unplanned subsystem outages. This paper presents an integrated operating modes analysis of the of the LINAC/CDS thermohydraulic loads satisfied by the CB/WCS cooling system supported by the RSYS inventory management system. The study is based on latest cryoplant and CDS engineering deliverables, as well as the recent performance data from single cryomodule qualification tests performed at the Fermilab PIP-II Injector Test test s tand. The study evaluates both normal and abnormal operating modes, with a focus on identifying integrated scenarios that put subsystems components under stress. The conclusions of this study will help build redundancy to reduce the risk of thermal cycles during planned and unplanned subsystem outages.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Validation of Modern Nuclear Data Processing in SCALE

The nuclear data (ND) community is continuously developing more accurate, diversified, and comprehensive data for radiation transport modeling to support the nuclear science community. As these community efforts progress, it is crucial that ND processing tools like AMPX (used for SCALE [1] ND) also be developed in parallel to incorporate these new data into transport codes and actually deliver those data to end users. AMPX is a mature, well-tested code that was developed by many people at Oak Ridge National Laboratory (ORNL) over the course of the past few decades. A large portion of the AMPX codebase, however, was outdated, difficult to maintain, and incompatible with modern code development tools. Some of the most important parts of the AMPX code have now been replaced with modern C++ code that can be maintained more cost-effectively and can be tested more rigorously.

AMPX↗

Density jumps near the virial radius of galaxy clusters

Recent simulations have indicated that the dark matter halos of galaxy clusters should feature steep density jumps near the virial radius. Since the member galaxies are expected to follow similar collisionless dynamics as the dark matter, the galaxy density profile should show such a feature as well. We examine the potential of current data sets to test this prediction by selecting cluster members for a sample of 56 low-redshift (0.1<z<0.3) galaxy clusters, constructing their projected number density profiles, and fitting them with two profiles, one with a steep density jump and one without. Additionally, we investigate the presence of a jump using a non-parametric spline approach. We find that some of these clusters show strong evidence for a model with a density jump, with the strength of the signal increasing with the inclusion of spectroscopic cluster member identification. We discuss avenues for further analysis of the density jump with future data sets, particularly with the inclusion of additional spectroscopy of cluster outskirts.

79 ASTRONOMY AND ASTROPHYSICS↗

Hybrid holographic non-destructive test system

An automatic hybrid holographic non-destructive testing (HNDT) method and system capable of detecting flaws or debonds contained within certain materials are described. This system incorporates the techniques of optical holography, acoustical/optical holography and holographic correlation in determining the structural integrity of a test object. An automatic processing system including a detector and automatic data processor is used in conjunction with the three holographic techniques for correlating and interpreting the information supplied by the non-destructive systems. The automatic system also includes a sensor which directly translates an optical data format produced by the holographic techniques into electrical signals and then transmits this information to a digital computer for indicating the structural properties of the test object. The computer interprets the data gathered and determines whether further testing is necessary as well as the format of this new testing procedure.

Kurtz, R. L.↗

Quiet Clean Short-haul Experimental Engine (QCSEE); acoustic performance of a 50.8-cm (20 inch) diameter variable pitch fan and inlet, test results and analysis, volume 1

Tests were run both in forward and in reverse thrust modes with a bellmouth inlet, five accelerating inlets (one hard wall and four treated) with a design throat Mach number of 0.79 at the takeoff condition, and four low Mach inlets (one hard wall and three treated) with a design throat Mach number of 0.6 at the takeoff condition. Unsuppressed and suppressed inlet radiated noise levels were measured at conditions representative of QCSEE takeoff, approach, and reverse thrust operations. Measured aerodynamic performance of the accelerating inlet is also included. The test objectives, facility, configurations, are described as well as the data analysis, results, and comparisons.

Bilwakesh, K. R.↗

Flow simulations for nacelle-propeller configurations using Euler equations

Euler codes for both axisymmetric and general three-dimensional nacelle-propeller flow analysis have been developed. Surface-fitted grids are generated either by a finite difference method or by an algebraic method. The propeller is represented by an actuator disk along a computational plane where proper boundary conditions are assigned to simulate the propeller power loading. Computed results for a NASA SR3 propeller as well as a NASA turboprop configuration are compared with test data. Good agreement has been achieved through the present simulation method.

Yu, N. J.↗

Earth radiation budget experiment software development

Computer programming and analysis efforts were carried out in support of the Earth Radiation Budget Experiment (ERBE) at NASA/Langley. The Earth Radiation Budget Experiment is described as well as data acquisition, analysis and modeling support for the testing of ERBE instruments. Also included are descriptions of the programs developed to analyze, format and display data collected during testing of the various ERBE instruments. Listings of the major programs developed under this contract are located in an appendix.

Edmonds, W. L.↗

In-flight thrust determination

The major aspects of processes that may be used for the determination of in-flight thrust are reviewed. Basic definitions are presented as well as analytical and ground-test methods for gathering data and calculating the thrust of the propulsion system during the flight development program of the aircraft. Test analysis examples include a single-exhaust turbofan, an intermediate-cowl turbofan, and a mixed-flow afterburning turbofan.

Abernethy, Robert B.↗

Using a modified Hewlett Packard 8410 network analyzer as an automated farfield antenna range receiver

A Hewlett Packard 8410 Network Analyzer was modified to be used as an automated far-field antenna range receiver. By using external mixers, analog to digital signal conversion, and an external computer/controller, the HP8410 is capable of measuring signals as low as -110 dBm. The modified receiver is an integral part of an automated far-field range which features computer controlled test antenna positioning, system measurement parameters, and data acquisition, as well as customized measurement file management. The system described was assembled and made operational, taking advantage of off-the-shelf hardware available at minimal cost.

Terry, John D.↗

A survey of spacecraft thermal design solutions

A review of activities at the NASA/Marshall Space Flight Center in the heat transfer and thermodynamics disciplines as well as attendant fluid mechanics, transport phenomena, and computer science applications is presented. Attention is focused on recent activities including the Hubble Space Telescope, and large space instruments, particularly telescope thermal control systems such as those flown aboard Spacelab 2 and the Astro missions. Emphasis is placed on defining the thermal control features, unique design schemes, and performance of selected programs. Results obtained both by ground testing and analytical means, as well as flight and postflight data are presented.

Humphries, R.↗

Properties of powder-impregnated graphite/PEKK

Poly Ether Ketone Ketone (PEKK) powders were prepregged on AS4 (12K), IM7 (12K), and G30-500 (12K) carbon fibers and consolidated into unidirectional laminates. The preferred formulation of PEKK for the dry powder process was identified. Mechanical test data on panels prepared via the powder process agreed well with flex, short beam shear, and double cantilever beam values obtained previously on melt-impregnated material. IM7/PEKK composites showed superior mechanical properties to AS4/PEKK and G30-500/PEKK composites. Transverse flexural strength and fiber/resin contact angle correlated well as measures of the fiber/matrix interfacial strength.

Bucher, R. A.↗

The evolution of procurement and assurance methods used to proof an advanced space material

A development history and current performance evaluation is presented for a Kapton polyimide for the Space Station Freedom. Analyses of results obtained for this class of materials by the Long Duration Exposure Facility led to major revisions of procurement specifications and test requirements for this material. Attention is given to the use of oxygen plasma etching and blocking, as well as the evolution of test methodologies due to preproduction test data evaluations and the relationship between tests and product-improvement cycles.

Berendt, Marjorie↗

Analysis of woven and braided fabric reinforced composites

A general purpose micromechanics analysis that discretely models the yarn architecture within the textile repeating unit cell, was developed to predict overall, three dimensional, thermal and mechanical properties. This analytical technique was implemented in a user-friendly, personal computer-based, windows compatible code called Textile Composite Analysis for Design (TEXCAD). TEXCAD was used to analyze plain, 5-harness satin, and 8-harness satin weave composites along with 2-D braided and 2x2, 2-D triaxial braided composites. The calculated overall stiffnesses correlated well with available 3-D finite element results and test data for both the woven and the braided composites. Parametric studies were performed to investigate the effects of yarn size on the yarn crimp and the overall thermal and mechanical constants for plain weave composites. The effects of braid angle were investigated for the 2-D braided composites. Finally, the effects of fiber volume fraction on the yarn undulations and the thermal and mechanical properties of 2x2, 2-D triaxial braided composites were also investigated.

Naik, Rajiv A.↗

Pegasus hypersonic flight research

Hypersonic aeronautics research using the Pegasus air-launched space booster is described. Two areas are discussed in the paper: previously obtained results from Pegasus flights 1 and 2, and plans for future programs. Proposed future research includes boundary-layer transition studies on the airplane-like first stage and also use of the complete Pegasus launch system to boost a research vehicle to hypersonic speeds. Pegasus flight 1 and 2 measurements were used to evaluate the results of several analytical aerodynamic design tools applied during the development of the vehicle as well as to develop hypersonic flight-test techniques. These data indicated that the aerodynamic design approach for Pegasus was adequate and showed that acceptable margins were available. Additionally, the correlations provide insight into the capabilities of these analytical tools for more complex vehicles in which design margins may be more stringent. Near-term plans to conduct hypersonic boundary-layer transition studies are discussed. These plans involve the use of a smooth metallic glove at about the mid-span of the wing. Longer-term opportunities are proposed which identify advantages of the Pegasus launch system to boost large-scale research vehicles to the real-gas hypersonic flight regime.

Curry, Robert E.↗

X-33 Tank Failure During Autoclave Fabrication

During a repair cure cycle on tank #1 of the X-33 liquid hydrogen tanks, a skin to core disbond occurred. Both the inner skin and outer skin of the lobe #1 sandwich panel was noted to have been disbonded and cracked- An investigation was undertaken to determine the cause of this failure. The investigation consisted of reviewing all of the processing data and performing testing on the failed lobe #1, as well as the other lobes, which did not fail during the cure cycle. The tests consisted of residual stress measurements in one of the intact lobes and "plug-pulls" to assess skin to core strength on all of the remaining lobes. Results showed an extremely low bondline strength due to lack of proper filleting of the adhesive, in addition, tests showed a very rapid decrease in strength with increasing temperature, as well as a further decrease in strength with a larger number of cycles. Also, the honeycomb used was not vented so pressure could build up within the cells. All of these factors appeared to be contributors to the failure.

Nettles, Alan T.↗