Search NASA⌕ Search

SEARCH · Search NASA

Results for “Yield Strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

High-speed friction stir butt welding of 25.4 mm thick 7175-T79 aluminum alloy

This presents the first experimental demonstration of friction stir butt welding of 25.4 mm thick high-strength, precipitate-strengthened 7XXX aluminum alloy at a welding speed above 500 mm/min and penetration depth greater than 10 mm. Tool pin threads that terminate away from the shoulder region, helped mitigate nearby stress concentration during tool traversing, enabling a higher welding speed while avoiding pin fracture near shoulder. Two kinds of welds—one-sided with full penetration of the plate thickness and double-sided with partial penetration of the plate thickness—were conducted. Significant grain refinement (grain size 1.3 ± 0.8 µm) was evident at the junction of double-sided friction stir welding (FSW) compared to other regions of weld-nugget or base material. Cross-weld tensile testing with digital image correlation revealed high local strains at the junction of double-sided FSW before macro-yield. This strain concentration impeded the typical early necking on advancing/retreating sides of FSW joints, improving the yield strength of as-welded double-sided FSW by 20–24% over slow- to medium-speed one-sided FSW. In conclusion, the joint efficiency of as-welded, double-sided high-speed FSW was about 76% with respect to the base material’s ultimate tensile strength.

36 MATERIALS SCIENCE↗

High performance Nb/TiNi nanocomposites produced by packaged accumulative roll bonding

Taking full advantage of intrinsic high strength of nano-reinforcements has been proven difficult in a composite until the concept of strain matching was experimental verified in a nanowire Nb/TiNi in-situ composite, which was obtained via solidifying eutectic Nb/TiNi and subsequent severe wire drawing. However, the volume fraction of the nano-reinforcement was dictated by eutectic reaction, which severely limited the development of high-performance composites. Here, the martensitic transformation nanocomposites were successfully acquired with increased volume fraction and changeable morphology of the nano-reinforcement through hot packaged ARB (PARB) and subsequent wire drawing. The nano-reinforcement with lamellar configuration in the composite could exhibit a large lattice strain of similar to 3.8%, which demonstrated the applicability and effectiveness of the strain matching principle in nano-lamellar composite. The obtained composites show a yield strength over 2.0 GPa and a quasi-linear elastic strain as larger as similar to 6.5% with adjustable apparent elastic modulus from 30 to 50 GPa.

42 ENGINEERING↗

Probabilistic finite elements

In the Probabilistic Finite Element Method (PFEM), finite element methods have been efficiently combined with second-order perturbation techniques to provide an effective method for informing the designer of the range of response which is likely in a given problem. The designer must provide as input the statistical character of the input variables, such as yield strength, load magnitude, and Young's modulus, by specifying their mean values and their variances. The output then consists of the mean response and the variance in the response. Thus the designer is given a much broader picture of the predicted performance than with simply a single response curve. These methods are applicable to a wide class of problems, provided that the scale of randomness is not too large and the probabilistic density functions possess decaying tails. By incorporating the computational techniques we have developed in the past 3 years for efficiency, the probabilistic finite element methods are capable of handling large systems with many sources of uncertainties. Sample results for an elastic-plastic ten-bar structure and an elastic-plastic plane continuum with a circular hole subject to cyclic loadings with the yield stress on the random field are given.

Belytschko, Ted↗

Size effect characteristics and influences on fatigue behavior of laser powder bed fusion of thin wall GRCop-42 copper alloy

Size effects, influencing a material's strength, elongation, fatigue limit, and longevity, depend on the operative and dominant deformation and failure mechanisms. This study explores the size effects in additive manufactured (AM) GRCop-42 (Cu-4at%Cr-2at%Nb) thin wall structures fabricated via laser-powder bed fusion (L-PBF) and their impact on fatigue life. The influence of internal defects and surface topography on the fatigue life of specimens in both as-built and hot isostatic pressed (HIP) conditions across different thicknesses is investigated. Where micro-computed tomography (μCT) was used to quantify the internal porosity of as-built, pristine HIP'd, and fatigued HIP'd specimens, and laser microscopy was employed to quantify the surface topography of specimens prior to fatigue. Additionally, quasi-static tests were used to establish baseline mechanical properties (i.e. yield strength (YS), ultimate tensile strength (UTS), and elongation) to frame fatigue testing conditions. Results indicate a significant enhancement in fatigue life for HIP'd specimens for both thicknesses, with internal defects depicting a greater impact than surface topography. Furthermore, fractographic analysis suggests that thicker specimens exhibit higher resistance to crack propagation during fatigue testing in the absence of substantial porosity. Thus, the size effects observed on the fatigue life of L-PBF GRCop-42 appears to be dominated by internal defects.

36 MATERIALS SCIENCE↗

Microstructural and Creep Properties of Boron- and Zirconium-Containing Cobalt-Based Superalloys

The effects of micro-additions of boron and zirconium on grain-boundary (GB) structure and strength inpolycrystalline γ(f.c.c.) plus γ’(L12) strengthened Co-9.5Al-7.5W-X at. % alloys (X=0-Ternary, 0.05B, 0.01B,0.05Zr, and 0.005B-0.05Zr at. %) are studied. Creep tests performed at 850 °C demonstrate that GB strength and cohesion limit the creep resistance and ductility of the ternary B- and Zr-free alloy due to intergranular fracture. Alloys with 0.05B and 0.005B-0.05Zr both exhibit improved creep strength due to enhanced GB cohesion,compared to the baseline ternary Co-9.5Al-7.5W alloy, but alloys containing 0.01B or 0.05Zr additions displayed no benefit. Atom-probe tomography (APT) is utilized to measure GB segregation, where B and Zr are demonstrated to segregate at GBs. A Gibbsian interfacial excess of 5.57 ± 1.04 atoms nm(exp) -2 was found for B at aGB in the 0.01B alloy and 2.88 ± 0.81 and 2.40 ± 0.84 atoms nm2 for B and Zr, respectively, for the 0.005B-0.05Zr alloy. The GBs in the highest B-containing (0.05B) alloy exhibit micrometer-sized boride precipitates with adjacent precipitate denuded-zones (PDZs), whereas secondary precipitation at the GBs is absent in theother four alloys. The 0.05B alloy has the smallest room temperature yield strength, by 6%, which is attributedto the PDZs, but it exhibits the largest increase in creep strength (with an ~2.5 order of magnitude decrease inthe minimum strain rate for a given stress at 850 °C) over the baseline Co-9.5Al-7.5W alloy.

Creep↗

A high strength Al-2Ni-0.5Zr conductor alloy fabricated via laser powder bed fusion

There is a current need for new aluminum alloy design strategies to target applications requiring high strength and conductivity with reductions in mass. A new lightweight Al-2Ni-0.5Zr (wt. %) conductor alloy was fabricated using laser powder bed fusion. A design of experiments probed the alloy's solidification cracking susceptibility. It was observed that solidification cracking was generally reduced with fast scan speeds, above 1500 mm/s, and smaller hatch spacings. The different cooling rates throughout the melt pool produced a heterogeneous distribution of cellular and equiaxed Al 3 Ni precipitates in the as-printed alloy. Additionally, the rapid solidification characteristic of laser powder bed fusion created a super-saturated Zr solid solution. An aging heat treatment at 375 °C for 24 h imparted strengthening through the precipitation of L1 2 -Al 3 Zr nanoprecipitates, which counteracted the softening caused by the fragmentation and coarsening of Al 3 Ni precipitates. The yield strength increased from 138 MPa in the as-printed condition to 168 MPa after aging, while the ductility remained constant at ∼21%. The aging treatment simultaneously increased the electrical conductivity from 40.8% IACS (International Annealed Copper Standard) to 53.5% IACS. Modeling of the strengthening mechanisms and electrical conductivity contributions rationalized the simultaneous increase in strength and conductivity upon aging. Furthermore, the strengthening efficacy of the Al 3 Ni and L1 2 -Al 3 Zr precipitates, combined with the low Ni and Zr solubility in the FCC Al matrix, facilitated both high strength and electrical conductivity. Overall, the combination of strength and electrical conductivity positions this alloy as a suitable choice for additively manufactured lightweight conductors.

Additive manufacturing↗

Additively manufactured β-Ti5553 with laser powder bed fusion: Microstructures and mechanical properties of bulk and lattice parts

Ti5553 (Ti-5Al-5Mo-5V-3Cr wt%) is a titanium alloy widely used for its high strength-to-weight ratio and good formability at elevated temperatures. Unlike Ti-6Al-4V, Ti5553 does not undergo martensitic transformation, preventing cracking of brittle martensite upon rapid cooling. This makes it a strong candidate for additive manufacturing (AM), particularly laser powder bed fusion (L-PBF). L-PBF offers the unique opportunity to make fine lattice structures to reduce component weight. Despite the growing field of AM, there have been limited studies on L-PBF Ti5553 lattices and how their properties differ from the bulk. Here the present work addresses this knowledge gap by investigating microstructures and properties of L-PBF bulk and lattice parts and the effect of post L-PBF heat treatments. Electron microscopy and mechanical testing show that the high dislocation density formed during L-PBF increases bulk part’s yield strength by approximately 100 MPa compared to the conventional alloy. Digital image correlation during compression testing of octet truss lattices reveals a layer-by-layer failure mode. Compared to the bulk, the lattice contains copious ω nanoprecipitation, weaker <001> texture, smaller average grain sizes, and larger content of high-angle grain boundaries. These features elicit differences in Taylor factor distributions for the lattice depending on load direction, underlining challenges in predicting lattice mechanical response based on bulk properties. By examining the processing-structure-property relationships in the bulk and lattice, the present results delineate their microstructural and mechanical differences and establish a benchmark for the future design applications of L-PBF Ti5553.

36 MATERIALS SCIENCE↗

Achieving High Strength and Creep Resistance in Inconel 740H Superalloy through Wire-Arc Additive Manufacturing and Thermodynamic-Guided Heat Treatment

Inconel 740H superalloy is commonly used in advanced ultra-supercritical power plants since it possesses excellent strength and creep resistance. This study investigates the microstructure and mechanical properties of Inconel 740H superalloy fabricated using wire-arc additive manufacturing. The as-printed microstructure consisted of columnar γ grains with the Laves phase and (Nb, Ti)C carbides as secondary phases. The anisotropy in grain structure increased from the bottom to the top regions, while the hardness was highest in the middle portion of the build. To guide the post-heat treatment design, thermodynamic and kinetic simulations were employed to predict the temperature and time. Complete recrystallization with the Laves phase dissolution occurred throughout the build after homogenization at 1200 °C for 2 h. The peak hardness was achieved after aging at 760 °C for 12 h with the M 23 C 6 carbides decorating the grain boundaries and γ’ precipitates in the grain interior. The yield strength (655 MPa) and ductility (29.5%) in the post-heat treated condition exceeded the design targets (620 MPa, 20%). Stress rupture tests at 750 °C showed that the high-temperature performance was at par with the wrought counterparts. The fracture mode after rupture was identified to be intergranular with the presence of grain boundary cavities along with grain boundary sliding.

36 MATERIALS SCIENCE↗

High-Strength, High-Ductility, High Entropy Alloys with High-Efficiency Native Oxide Solar Absorbers for Concentrating Solar Power Systems

This EPSCoR Project has been investigating the synergy between the excellent high-temperature mechanical behavior of FeMnNiAlCr high entropy alloys (HEA) and the high solar absorptance of their native oxides for high efficiency concentrated solar thermal power (CSP) systems working at >700°C. While HEAs have attracted substantial interest in recent years, most investigations have focused on their applications as structural materials rather than functional materials. This EPSCoR project discovered that FeMnNiAlCr HEAs can potentially be applied synergistically as both a structural and functional material for high-efficiency concentrating solar thermal power (CSP) systems working at >700°C. The HEA itself would be used in high-temperature tubing to carry molten salts or supercritical CO 2 , while its surface oxide would act as a high-efficiency solar thermal absorber. With Fe and Mn being the major components in these HEAs (adding up to ~70 at.% of the alloy), these materials are much more cost-effective than the Ni-based superalloys currently being investigated for high-temperature CSP systems. Through this research, these Fe-Mn based HEAs have demonstrated yield strengths 2-3x greater than that of stainless steel at 700°C and a creep lifetime >800 h at 700ºC under a typical CSP tubing mechanical load of 35 MPa. Their Mn-rich surface oxides maintain a high optical-to-thermal conversion efficiency of ~87% under 1000x solar concentration ratio for 20 simulated day-night thermal cycles between 750ºC and room temperature. In preliminary corrosion studies, these HEAs have sustained immersion in unpurified bromide molten salts for 14 days at 750°C with <2% weight loss, in contrast to 70% weight loss from a 316 stainless steel reference. The simultaneous achievement of promising mechanical, optical, and thermochemical properties in this FeMnNiAlCr system opens the door to new applications of HEAs in solar energy harvesting. Partnerships with Ames Laboratory and Oak Ridge National Laboratory (ORNL) also advanced our understanding of the fundamental structure-property relationships through atomic scale material characterization and first-principles computational modeling. The key research results in this project can potentially be extended to other HEAs and their native oxides. In terms of applications, the proposed FeMnNiAlCr HEA/native oxide system could potentially exceed the mechanical and the optical performance of existing tubing and solar coating materials under EERE’s CSP program at lower cost, which also aligns well with the EPSCoR Science and Technology strategies of New Hampshire in boosting the deployment of renewable energy.

14 SOLAR ENERGY↗

Irradiation Enhances Strength and Deformability of Nano‐Architected Metallic Glass

The quest for radiation‐damage tolerant materials has found good candidates in nanoporous metals, whose abundance of free surfaces provides ample sinks for radiation‐induced defects, as well as in metallic glasses, whose characteristic failure via shear banding can be alleviated by irradiation. This type of catastrophic failure in metallic glass can also be suppressed by reducing their dimensions to the nanoscale. To combine the beneficial effects of resilience against irradiation in materials containing many free surfaces and nano‐sized metallic glasses, the authors fabricate Zr–Ni–Al metallic glass nano‐architecture and irradiate them with 12 MeV Ni 4+ ions. These 3D nanolattices are composed of hollow beams of sputtered metallic glass with beam wall thicknesses ≈10–100 nm, with a relative density of ≈5%, which renders them to be 20 times lighter than their bulk‐level counterparts. The authors find that the thickest‐walled nanolattices, those with a median wall thickness of ≈88 nm, are able to withstand irradiation without significant contraction; all other substantially shrunk; and collapsed upon irradiation. In situ nanomechanical experiments on the irradiated samples compressed inside a scanning electron microscope (SEM) reveal substantial improvement in mechanical response upon irradiation, with an average increase in yield strength of 35.7% and a significant enhancement in deformability. Enhanced deformability upon irradiation is apparent from the nanolattices' accommodation of larger strains before any kind of failure, as well as the presence of smaller strain bursts and stress drops throughout the stress–strain response. The irradiated nanolattices are largely intact after compression, with in situ SEM videos demonstrating a layer‐by‐layer like collapse in the irradiated nanolattices in contrast to the catastrophic failure with complete destruction of the failed layers observed in equivalent as‐fabricated samples. This work points to nano‐architected metallic glasses being a promising candidate for creating ultra‐lightweight, radiation tolerant materials, and irradiation as a promising technique for improving the mechanical response of metallic glass nanolattices with stiffness on the order of 250 MPa.

Thompson, Rachel L.↗

High strength and high ductility in a novel Fe 40.2 Ni 11.3 Mn 30 Al 7.5 Cr 11 multiphase high entropy alloy

In the present study, a novel Fe 40.2 Ni 11.3 Mn 30 Al 7.5 Cr 11 high entropy alloy displaying an excellent com- bination of high strength and high ductility has been developed. The b.c.c.þB2/f.c.c. dendritic- interdendritic microstructure was characterized using scanning electron microscopy, X-ray diffraction, and transmission electron microscopy, and the alloy’s mechanical properties were examined using Vickers hardness measurements and room-temperature tensile tests. The phase stability of Fe 40.2 Ni 11.3 Mn 30 Al 7.5 Cr 11 was investigated by annealing the alloy between 1173 Ke1273 K, and the presence of both Ni-rich, b.c.c. needle-shaped precipitates and Cr-rich, s phase particles was observed for the 1173 K annealed specimen. The s phase precipitates contributed to the rapid age-hardening effect in the material annealed at 1173 K. A further increase in ageing temperature to 1223 K and 1273 K led to the dissolution of the s phase and a reduction in the volume fraction of the b.c.c./B2 dendrites, which led to a consequent drop in room-temperature yield strength from the as-cast value of ~593 MPae~486 MPa and ~228 MPa for the specimens annealed at 1223 K and 1273 K, respectively. An accompanying increase in ductility was observed from ~22% for the as-cast alloy to ~27% and ~40% after annealing the material at 1223 K and 1273 K, respectively. Post-deformation transmission electron micrographs revealed that the f.c.c interdendrites accommodated plastic strain via wavy slip and moreover, deformed before the b.c.c. dendritic regions, which were reinforced by B2 particles and acted as obstacles to moving dislocations. Finally, the discovery of a multi-phase HEA that contains 11% Cr and good mechanical properties has relevant high-temperature structural applications especially in cases that require suitable corrosion resistance.

36 MATERIALS SCIENCE↗

Influence of mechanical alloying and extrusion conditions on the microstructure and tensile properties of Low-Cr ODS FeCrAl alloys

Low-chromium (<10%Cr) high strength oxide dispersion strengthened (ODS) FeCrAl alloys are considered promising candidates for accident tolerant fuel cladding in light water fission reactors. These alloys are designed to combine the beneficial high temperature mechanical properties of ODS materials with the exceptionally high temperature oxidation resistance of FeCrAl in comparison to conventional Zr-containing cladding materials, while also providing good mechanical and aqueous corrosion behavior under normal light water reactor operating conditions. The initial (1st generation) ODS FeCrAl alloys combined gas atomized FeCrAl powders with yttria and other oxides for alloying element additions using the mechanical alloying approach. These alloys exhibited low ductility but excellent high temperature tensile strength while maintaining good oxidation resistance at temperatures up to 1400 °C. In an attempt to improve alloy ductility for accident tolerant fuel cladding applications, new low-Cr ODS FeCrAl alloys with decreased oxygen content were developed with the Zr alloying solute already gas atomized into the powder prior to mechanical alloying. The resultant Fe-10Cr-6.1Al-0.3Zr+0.3Y 2 O 3 (106ZY) powders were ball milled for 10, 20, and 40hr followed by consolidation via hot extrusion at temperatures ranging from 900 to 1050 °C. Increasing the mechanical alloying time decreased the resultant grain size and improved high temperature tensile properties. Decreasing the extrusion temperature refined the grain size and subsequently strengthened the ODS FeCrAl 106ZY alloys while lowering the ductility. Scanning transmission electron microscopy (STEM) and energy dispersive spectroscopy (EDS) demonstrated the Zr solute addition effectively sequestered impurity C and N within the matrix. The root mean square (RMS) hardening superposition model for yield strength shows good agreement with experimental results. Errors between predicted and experimental values are discussed within the scope of processing parameters. As a result, these 2nd generation 106ZY alloys show a distinct increase in alloy ductility without sacrificing the high temperature tensile properties characteristic of legacy or 1st generation ODS FeCrAl alloys.

36 MATERIALS SCIENCE↗

Nanoindentation of Micrograins in Polycrystals under Multiaxial Stress: Control of Abrupt & Stochastic Plastic Events

Deforming objects in the world of the small has proven a much more complex task than just bending a common-sized object like a spoon. Over the last decade, it has become clear that the application of stress on micron-sized objects, such as micropillars, leads to abrupt and stochastic plastic strain jumps that do not satisfy Weibull statistics (as expected for uncorrelated defect yielding) but instead seem to follow highly wide, power-law distributions, pointing towards cooperative dislocation plasticity. Are power-law distributed plastic events the rule or the exception in crystals? If the rule, can we design protocols to control and suppress them in order to achieve deterministic and smooth microforming processes? We propose to combine experiments and theory to unravel the mysteries of abrupt microplastic deformation in a natural dislocation environment: micron-sized grains (\micrograins") of polycrystals. We propose a novel experimental design that utilizes nanoindentation and 4-point bending techniques on the substrate of polycrystalline thin films of two typical FCC metals (Al and Cu), and make concrete theoretical conjectures, based on intuition built from previous theoretical and experimental efforts in micropillar compression and nanoindentation. Based on a wide set of observations over the last decade, we put forward two distinct hypotheses that we propose to investigate in both theory and experiments: Our first conjecture is that crystal plasticity in the central region of micron-sized grains has micropillar-like stochastic features: power-law plastic strain jumps at stresses above the macroscale yield strength, displaying strong size and rate effects. We will demonstrate this similarity in spherical nanoindentation experiments in the central-region of multi-orientation grains of Al and Cu thin films. Al and Cu are selected for their disparity in stacking fault energy and consequently, their different propensity for cross-slip relaxation; however, our protocol may be applied to any crystalline material of technological interest. We will test our hypothesis by performing two-dimensional extended discrete dislocation plasticity (2.5D-DDP) simulations, inspired by comparable successful studies of micropillar plasticity, and extended to model nanoindentation with two slip systems and on a surface of a bicrystal with microhard grain-boundaries (GB), ie. not allowing dislocation absorption (116). Our model will include effective three dimensional dislocation mechanisms such as dislocation multiplication and double-cross-slip assisted glide. Second, we hypothesize that the application of uniform in-plane stress on our thin films below the yield point can smoothen the micrograin plastic response during nanoindentation. On a technological level, we propose that indentation-induced localization (sink-in) may be diminished by the application of concurrent in-plane stress that activates slow, viscoplastic relaxations near GBs. We aim to demonstrate our hypothesis through a 4-point bending apparatus that introduces a homogeneous in-plane stress state before indentation. We will perform simulations of a coarse-grained mesoscale theory of plasticity in a system with microhard GBs, benchmarked through 2.5D-DDP simulations, which will capture the effects of slow viscoplastic relaxations. Our nanoindentation abrupt event statistics studies, either in the micrograin interior or near GBs, will be correlated to direct observations of induced surface dislocation microstructures. For we will use TEM-based methods (PACOM/TKD) in combination with EBSD. Indents placed in the center of grains will be analyzed based on the orientation of the grain, while those near to GBs will be analyzed based on the orientation of each grain, the distance from the GB and the 5 degrees of freedom of the GB.

36 MATERIALS SCIENCE↗

The effect of thermomechanical treatment and tempering on the subsurface microstructure and bendability of direct-quenched low-carbon strip steel

Highlights: • Surface properties mainly determine the bendability of high strength steel. • Tempering improves bendability by softening the microstructure. • Surface texture is affected by thermomechanical treatment but not by tempering. • Strong shear texture component and upper bainite are detrimental to bendability. - Abstract: Recent results in the literature have shown that subsurface properties play a key role during the bending of steel plates. Now, for the first time, surface microstructure, surface texture, subsurface hardness and dislocation density have been studied to reveal the effect of tempering and thermomechanical treatment on the bendability of a direct-quenched strip steel. In the experiments, different thermomechanical treatments as well as non-isothermal tempering treatments were performed with slow heating to 570 °C and slow cooling to simulate the tempering of large steel coils in a batch annealing furnace. The results show that in addition to the improved production efficiency obtained through direct quenching and a single tempering process, tempering improves bendability by reducing subsurface dislocation density and hardness without a significant loss of strip yield strength. The subsurface microstructure and texture of the strip are the result of thermo-mechanical processing and transformation behaviour. Upper bainite containing elongated Martensite-Austenite (MA) islands in addition to an intense shear texture component {112}<111>{sub α} leads to shear band formation, and therefore poorer bendability when the bend axis is perpendicular to the rolling direction. This texture is not affected by tempering. Therefore, tempering does not improve the bendability of steels with an unfavourable texture. When the subsurface layers comprise a softer ferritic microstructure, good bendability is obtained in the untempered direct-quenched condition with a modest improvement caused by tempering.

36 MATERIALS SCIENCE↗

Biologically inspired reinforcement using polydopamine of polymer bound composites

Interfacial strength plays a critical role in the mechanical properties of a composite system. In this work, a proven mock high explosive (HE), 5-iodo-2’-deoxyuridine (IDOX) was coated by the adhesive promoting polymer polydopamine (PDA), then formulated with an Estane binder system to form an improved HE mock composite. An extensive comparison study of mechanical properties was performed to determine the effects, if any, of PDA on the composite system. To aid in interpretation of the mechanical test data, neutron reflectometry experiments were performed to determine the thickness and structure of the as deposited PDA films. The mechanical performance of PDA-treated IDOX was then compared to untreated specimens by compression testing in the Brazilian disk geometry. The results strongly suggested that the structure of PDA consists of two layers: one low in density caused by polymer agglomerates attaching to the substrate during polymerization, and the second high in density caused by controlled linear deposition of polydopamine. Finally, the mechanical testing showed that PDA greatly increased the stiffness and yield strength of IDOX based mocks without causing any disruption to the underlying crystal system.

42 ENGINEERING↗

Martensitic transformation induced strength-ductility synergy in additively manufactured maraging 250 steel by thermal history engineering

Maraging steels are known for their exceptional strength but suffer from limited work hardening and ductility. Here, in this study, we report an intermittent printing strategy to tailor the microstructure and mechanical properties of maraging 250 steel via tuning the thermal history during wire-arc directed energy deposition. By introducing a dwell time between adjacent layers, the maraging 250 steel is cooled below the martensite start temperature, triggering thermally-driven martensitic transformation during the printing process. Thermal cycling during subsequent layer deposition results in the formation of reverted austenite which shows a refined microstructure and induces elemental segregation between martensite and reverted austenite. The Ni enrichment in the austenite promotes stabilization of the reverted austenite upon cooling to room temperature. The reverted austenite is metastable during deformation, leading to strain-induced martensitic transformation under loading. Specifically, a 3 min interlayer dwell time produces a maraging 250 steel with approximately 8% reverted austenite, resulting in improved work hardening via martensitic transformation induced plasticity during deformation. Meanwhile, the higher cooling rate and refined prior austenite grains lead to substantially refined martensitic grains (by approximately fivefold) together with an increased dislocation density. With 3 min interlayer dwell time, the yield strength of the printed maraging 250 steel increases from 836 MPa to 990 MPa, and the uniform elongation is doubled from 3.2% to 6.5%. This intermittent deposition strategy demonstrates the potential to tune the microstructure of maraging steels for achieving strength-ductility synergy by engineering the thermal history during additive manufacturing.

Additive manufacturing↗

Studies on the Module Structure for the NOvA Liquid Scintillator Neutrino Detector

This thesis contains studies pertinent to the construction of modules for the NOνAexperiment detectors. The tensile strength of acrylic and epoxy adhesives used in construction of the detector was studied over time and with various surface preparations. Sanding and corona discharge surface treatments increased the bond strength of the acrylic by 10-20%; aging in oil did not affect the acrylic bond strength while aging in air at 50°C for 9 months (equivalent to approximately 5 years at room temperature) increased the acrylic bond strength by 25%. For the epoxy, corona discharge treated samples’ strength increased slightly after aging while the strength of sanded samples in air remained consistent and sanded samples in oil decreased by 17% when aged at 50°C for 1.5 years (equivalent to approximately 10 years at room temperature).All materials used in the detector were studied to determine if degrading interaction would occur with the pseudocumene liquid scintillator. Substances such as acrylic adhesive and PTFE paste were found to interact with the scintillator while materials such as a variety of PVCs, epoxy adhesives, and PTFE tape were found to be non-reactive with the scintillator. Following the appearance of cracks on manifold covers in installed modules, studies were carried out to help to determine the cause and mitigation of these cracks. Manifold covers that had been pressure tested at various pressures during the check of the seals during the manufacturing process were examined for the formation of cracks. “Containment units” were used to constrain the swelling of the manifold covers during pressure testing. Internal cracks were visible on the majority of manifold covers tested at 1.4 bar with the original containment units. It was found that reducing the pressure testing of the modules from 1.4 bar to 0.7 bar and increasing the rigidity of the pressure test containment units eliminated the formation of visible cracks in the manifold covers. Stress concentration in small fillet radius injection molded PVC was studied. GeonM3500 PVC has a yield strength 12% greater than Geon M3800 PVC originally used for the manifold covers but increased the stress concentrated failure time by 6600% and was thus chosen to mold new manifold covers after a redesign to eliminate stress concentrating features.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

The performance of additively manufactured Haynes 282 in supercritical CO 2

The use of supercritical carbon dioxide (sCO 2 ) as a working fluid is garnering interest in next generation power production systems due to the possibility of increased operational efficiencies and lower associated costs. Its implementation requires alloys with excellent high temperature strength and corrosion resistance, which makes Haynes 282® (H282) a suitable candidate. With increasing adoption of additive manufacturing (AM) in the energy industry, there is a need to investigate long-term sCO2 exposure on AM produced materials. Additively manufactured H282 (AM-H282) samples built using laser powder bed fusion in two different orientations were analyzed through imaging, gravimetric analysis, and room-temperature tensile testing before and after 1000-h exposure to CO 2 at 750 °C and 20 MPa. Performed imaging included observation of the sample surfaces and of the material bulk (cross sections) through means of Scanning Electron Microscopy (SEM) and optical microscopy. In comparison to wrought H282, it was found that the exposed material exhibited a similar Cr 2 O 3 oxide protective layer about 2 μm in thickness with additional top-surface TiO 2 oxide and carbon-rich precipitates. It was also similarly observed that internal oxidation was present but limited to a depth of 20 μm, and a 1–3 μm γ’ denuded region appeared to surround all internal and surface oxidation. Thermal aging effects were noted with the precipitation of needle-like structures in the γ/γ’ matrix and a coarsening of the γ’ precipitates from 28 nm to 73 nm. Mass measurements analyzing oxide precipitation revealed a larger increase compared to wrought, representing an approximate 20% difference. Tensile testing results showed similar behavior to wrought with a slight increase in yield strength and a large reduction in elongation in the exposed samples.

36 MATERIALS SCIENCE↗