Search NASA⌕ Search

SEARCH · Search NASA

Results for “dispersion function”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Effect of x-ray energy dispersion in digital subtraction imaging at the iodine K-edge--A Monte Carlo study

The effect of the energy dispersion of a quasi-monochromatic x-ray beam on the performance of a dual-energy x-ray imaging system is studied by means of Monte Carlo simulations using MCNPX (Monte Carlo N-Particle eXtended) version 2.6.0. In particular, the case of subtraction imaging at the iodine K-edge, suitable for angiographic imaging application, is investigated. The average energies of the two beams bracketing the iodine K-edge are set to the values of 31.2 and 35.6 keV corresponding to the ones obtained with a compact source based on a conventional x-ray tube and a mosaic crystal monochromator. The energy dispersion of the two beams is varied between 0 and 10 keV of full width at half-maximum (FWHM). The signal and signal-to-noise ratio produced in the simulated images by iodine-filled cavities (simulating patient vessels) drilled in a PMMA phantom are studied as a function of the x-ray energy dispersion. The obtained results show that, for the considered energy separation of 4.4 keV, no dramatic deterioration of the image quality is observed with increasing x-ray energy dispersion up to a FWHM of about 2.35 keV. The case of different beam energies is also investigated by means of fast simulations of the phantom absorption.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Effect of structural defects on anomalous ultrasound propagation in solids during second-order phase transitions

The effect of structural defects on the critical ultrasound absorption and ultrasound velocity dispersion in Ising-like three-dimensional systems is studied. A field-theoretical description of the dynamic effects of acoustic-wave propagation in solids during phase transitions is performed with allowance for both fluctuation and relaxation absorption mechanisms. The temperature and frequency dependences of the scaling functions of the absorption coefficient and the ultrasound velocity dispersion are calculated in a two-loop approximation for homogeneous and structurally disordered systems, and their asymptotic behavior in hydrodynamic and critical regions is separated. As compared to a homogeneous system, the presence of structural defects in it is shown to cause a stronger increase in the sound absorption coefficient and the sound velocity dispersion even in the hydrodynamic region as the critical temperature is reached. As compared to homogeneous analogs, structurally disordered systems should exhibit stronger temperature and frequency dependences of the acoustic characteristics in the critical region.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Swept frequency technique for dispersion measurement of microstrip lines

Microstrip lines used in microwave integrated circuits are dispersive. Because a microstrip line is an open structure, the dispersion can not be derived with pure TEM, TE, or TM mode analysis. Dispersion analysis has commonly been done using a spectral domain approach, and dispersion measurement has been made with high Q microstrip ring resonators. Since the dispersion of a microstrip line is fully characterized by the frequency dependent phase velocity of the line, dispersion measurement of microstrip lines requires the measurement of the line wavelength as a function of frequency. In this paper, a swept frequency technique for dispersion measurement is described. The measurement was made using an automatic network analyzer with the microstrip line terminated in a short circuit. Experimental data for two microstrip lines on 10 and 30 mil Cuflon substrates were recorded over a frequency range of 2 to 20 GHz. Agreement with theoretical results computed by the spectral domain approach is good. Possible sources of error for the discrepancy are discussed.

Lee, R. Q.↗

Swept frequency technique for dispersion measurement of microstrip lines

Microstrip lines used in microwave integrated circuits are dispersive. Because a microstrip line is an open structure, the dispersion can not be derived with pure TEM, TE, or TM mode analysis. Dispersion analysis has commonly been done using a spectral domain approach, and dispersion measurement has been made with high Q microstrip ring resonators. Since the dispersion of a microstrip line is fully characterized by the frequency dependent phase velocity of the line, dispersion measurement of microstrip lines requires the measurement of the line wavelength as a function of frequency. In this paper, a swept frequency technique for dispersion measurement is described.

Lee, Richard Q.↗

Van der Waals density functional: an appropriate exchange functional

In this paper, an exchange functional which is compatible with the non-local Rutgers-Chalmers correlation functional (vdW-DF) is presented. This functional, when employed with vdW-DF, demonstrates remarkable improvements on intermolecular separation distances while further improving the accuracy of vdW-DF interaction energies. The key to the success of this three parameter functional is its reduction of short range exchange repulsion through matching to the gradient exchange approximation in the slowly varying/high density limit while recovering the large reduced gradient, s, limit set in the revised PBE exchange functional. This augmented exchange functional could be a solution to long-standing issues of vdW-DF lending to further applicability of density functional theory to the study of relatively large, dispersion bound (van der Waals) complexes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Perspective: How good is DFT for water?

Kohn-Sham density functional theory (DFT) has become established as an indispensable tool for investigating aqueous systems of all kinds, including those important in chemistry, surface science, biology, and the earth sciences. Nevertheless, many widely used approximations for the exchange-correlation (XC) functional describe the properties of pure water systems with an accuracy that is not fully satisfactory. The explicit inclusion of dispersion interactions generally improves the description, but there remain large disagreements between the predictions of different dispersion-inclusive methods. We present here a review of DFT work on water clusters, ice structures, and liquid water, with the aim of elucidating how the strengths and weaknesses of different XC approximations manifest themselves across this variety of water systems. Our review highlights the crucial role of dispersion in describing the delicate balance between compact and extended structures of many different water systems, including the liquid. By referring to a wide range of published work, we argue that the correct description of exchange-overlap interactions is also extremely important, so that the choice of semi-local or hybrid functional employed in dispersion-inclusive methods is crucial. The origins and consequences of beyond-2-body errors of approximate XC functionals are noted, and we also discuss the substantial differences between different representations of dispersion. We propose a simple numerical scoring system that rates the performance of different XC functionals in describing water systems, and we suggest possible future developments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

New XDM-corrected potential energy surfaces for Ar–NO(X{sup 2}Π): A comparison with CCSD(T) calculations and experiments

We report new potential energy surfaces for the ground state Ar–NO(X{sup 2}Π) van der Waals system calculated using the unrestricted Hartree-Fock (UHF) method with the addition of the Becke-Roussel correlation functional and exchange-hole dipole moment dispersion correction (XDM). We compare UHFBR-XDM surfaces and those previously reported by Alexander from coupled cluster CCSD(T) calculations [J. Chem. Phys. 111, 7426 (1999)]. The bound states of Ar–NO have been investigated with these new UHFBR-XDM surfaces, including relative energy-level spacing, adiabatic bender states and wave functions, and spectroscopic data. These results have been found to be in good agreement with calculations based on the CCSD(T) PESs. These new PESs are used to investigate the inelastic scattering of NO(X) by Ar. Full close-coupling integral cross sections at collision energies of 442 cm{sup −1}, 1774 cm{sup −1} and differential cross sections at collision energy of 530 cm{sup −1} were determined for transitions out of the lowest NO(X) rotational level (j = ω = 1/2,f). These cross sections are in good agreement with those calculated with CCSD(T) and accordingly in good agreement with the most recent initial and final state resolved experimental data. The UHFBR-XDM scheme yields high-quality potential surfaces with computational cost comparable to the Hartree-Fock method and our results may serve as a benchmark for application of this scheme to collisions between larger molecules.

74 ATOMIC AND MOLECULAR PHYSICS↗

Tuning surface properties of amino-functionalized silica for metal nanoparticle loading: The vital role of an annealing process

Metal nanoparticles (NPs) loaded on oxides have been widely used as multifunctional nanomaterials in various fields such as optical imaging, sensors, and heterogeneous catalysis. However, the deposition of metal NPs on oxide supports with high efficiency and homogeneous dispersion still remains elusive, especially when silica is used as the support. Amino-functionalization of silica can improve loading efficiency, but metal NPs often aggregate on the surface. Herein, we report that a facial annealing of amino-functionalized silica can significantly improve the dispersion and enhance the loading efficiency of various metal NPs, such as Pt, Rh, and Ru, on the silica surface. A series of characterization techniques, such as diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), Zeta potential analysis, UV–Vis spectroscopy, thermogravimetric analysis coupled with infrared analysis (TGA–IR), and nitrogen physisorption, were employed to study the changes of surface properties of the amino-functionalized silica before and after annealing. We found that the annealed amino-functionalized silica surface has more cross-linked silanol groups and relatively lesser amount of amino groups, and less positively charges, which could be the key to the uniform deposition of metal NPs during the loading process. Lastly, these results could contribute to the preparation of metal/oxide hybrid NPs for the applications that require uniform dispersion.

36 MATERIALS SCIENCE↗

Visualization and Quantum Computation of Moire Superconductivity in Bilayer Graphene, Carbon Nanocones and Nanostrips

The purpose of this project is to visualize and study the electronic properties of carbon nanostructures. The principal structures studied are AA and AB (Bernal) stacked graphene bilayers, an 80C nanocone with pentagonal defects at its apex, and a 16C nanoring. Graphene and other based nanostructures have attracted much attention due to their unique electronic properties. For example, bilayer graphene shows superconductivity at certain magic angles of rotation. Open source molecular modeling and visualization programs like SAMSON, Avogadro, and VMD are utilized to generate the structures above. Using bond information in order to find nearest neighbors, an adjacency matrix can be generated from which the energy eigenvalues are solvable and are used to visualize the dispersion relation, free energy, persistent current, Green’s function, and entanglement entropy. The goal of this project is to study the effect of rotation on the electronic properties of bilayer graphene, particularly as it pertains to the magic angle where superconductivity occurs, as well as the electronic properties of the bilayer Moire patterns which emerge due to the superposition of the identical lattices at different angles. An important goal is to incorporate phonon interactions into the tight-binding model for carbon structures, and to utilize quantum based computing as a tool to find the ground state properties of these structures, particularly in the terminating case where boundary conditions have an effect.

97 MATHEMATICS AND COMPUTING↗

Generation efficiency of single-photon current pulses in the Geiger mode of silicon avalanche photodiodes

Statistical fluctuations of the avalanche's multiplication efficiency were studied as applied to the single-photon (Geiger) mode of avalanche photodiodes. The distribution function of partial multiplication factors with an anomalously wide (of the order of the average) dispersion was obtained. Expressions for partial feedback factors were derived in terms of the average gain and the corresponding dependences on the diode's overvoltage were calculated. Final expressions for the photon-electric pulse's conversion were derived by averaging corresponding formulas over the coordinate of initiating photoelectron generation using the functions of optical photon absorption in silicon.

36 MATERIALS SCIENCE↗

Optical properties of mercury ion thruster exhaust plumes Significance for candidate SEP science instruments

Emission from the exhaust plume of a 30 cm mercury ion thruster was measured from 160 to 600 nm as a function of axial and radial distance from the thruster discharge chamber. The spectrally dispersed absolute intensities were used to construct an empirical volume emission rate function. The function was integrated along a typical instrument field of view, and the resulting apparent brightness was compared with instrument sensitivities to evaluate the extent of optical interference. The intensity levels degraded rapidly with distance from the thruster so that optical interference was negligible for fields of view not intercepting the beam axis. The operation of only one instrument, a zodiacal photopolarimeter was considered incompatible with simultaneous thruster operation.

Goldstein, R.↗

Temperature, humidity and air flow in the emplacement drifts using convection and dispersion transport models

A coupled thermal-hydrologic-airflow model is developed, solving for the transport processes within a waste emplacement drift and the surrounding rockmass together at the proposed nuclear waste repository at Yucca Mountain. Natural, convective air flow as well as heat and mass transport in a representative emplacement drift during post-closure are explicitly simulated, using the MULTIFLUX model. The conjugate, thermal-hydrologic transport processes in the rockmass are solved with the TOUGH2 porous-media simulator in a coupled way to the in-drift processes. The new simulation results show that large-eddy turbulent flow, as opposed to small-eddy flow, dominate the drift air space for at least 5000 years following waste emplacement. The size of the largest, longitudinal eddy is equal to half of the drift length, providing a strong axial heat and moisture transport mechanism from the hot to the cold drift sections. The in-drift results are compared to those from simplified models using a surrogate, dispersive model with an equivalent dispersion coefficient for heat and moisture transport. Results from the explicit, convective velocity simulation model provide higher axial heat and moisture fluxes than those estimated from the previously published, simpler, equivalent-dispersion models, in addition to showing differences in temperature, humidity and condensation rate distributions along the drift length. A new dispersive model is also formulated, giving a time- and location-variable function that runs generally about ten times higher in value than the highest dispersion coefficient currently used in the Yucca Mountain Project as an estimate for the equivalent dispersion coefficient in the emplacement drift. The new dispersion coefficient variation, back-calculated from the convective model, can adequately describe the heat and mass transport processes in the emplacement drift example.

54 ENVIRONMENTAL SCIENCES↗

THE CONVERGENCE OF PARTICLE-IN-CELL SCHEMES FOR COSMOLOGICAL DARK MATTER SIMULATIONS

Particle methods are a ubiquitous tool for solving the Vlasov–Poisson equation in comoving coordinates, which is used to model the gravitational evolution of dark matter (DM) in an expanding universe. However, these methods are known to produce poor results on idealized test problems, particularly at late times, after the particle trajectories have crossed. To investigate this, we have performed a series of one- and two-dimensional “Zel’dovich pancake” calculations using the popular particle-in-cell (PIC) method. We find that PIC can indeed converge on these problems provided that the following modifications are made. The first modification is to regularize the singular initial distribution function by introducing a small but finite artificial velocity dispersion. This process is analogous to artificial viscosity in compressible gas dynamics, and, as with artificial viscosity, the amount of regularization can be tailored so that its effect outside of a well-defined region—in this case, the high-density caustics—is small. The second modification is the introduction of a particle remapping procedure that periodically reexpresses the DM distribution function using a new set of particles. We describe a remapping algorithm that is third-order accurate and adaptive in phase space. This procedure prevents the accumulation of numerical errors in integrating the particle trajectories from growing large enough to significantly degrade the solution. Once both of these changes are made, PIC converges at second order on the Zel’dovich pancake problem, even at late times, after many caustics have formed. Furthermore, the resulting scheme does not suffer from the unphysical, small-scale “clumping” phenomenon known to occur on the pancake problem when the perturbation wavevector is not aligned with one of the Cartesian coordinate axes.

79 ASTRONOMY AND ASTROPHYSICS↗

Spontaneous Formation of 1D Pattern in Monolayer VSe 2 with Dispersive Adsorption of Pt Atoms for HER Catalysis

Creation of functional patterns in two-dimensional (2D) materials provides opportunities to extend their potential for applications. Transition-metal dichalcogenides (TMDCs) are suitable 2D materials for pattern generation because of properties including alterable polymorphic phases, easy chalcogen-vacancy formation, metal-atom insertion, and alloying. Such patterning can be used for selective functionalization. Here we report the spontaneous formation of long-range, well-ordered 1D patterns in monolayer vanadium diselenide (VSe 2 ) by a single annealing stage during growth. Atomic-resolution images in real space combined with density-functional-theory (DFT) calculations reveal the 1D features of patterned VSe 2 . Further experimental characterization of the intermediate states in the growth process confirm the spontaneous formation of the 1D pattern by annealing-induced Se-deficient linear defects. The 1D pattern can be reversibly transformed to homogenous VSe 2 monolayer by reintroducing Se atoms. Moreover, additional experiments demonstrate that a dispersive deposition of Pt atoms along the 1D structures of patterned VSe 2 is achieved, while DFT calculations find that their catalytic activity for hydrogen evolution reaction (HER) is as good as that of Pt surfaces. Further, the formation of long-range, well-ordered 1D patterns not only demonstrates an effective way of dimension modulation in 2D materials but also enriches the potential of intrinsically patterned 2D materials for promising catalytic activities.

Chemical structure↗

In-situ synchrotron X-ray investigation of phase evolution in gas atomized powder enabling manufacturing of nanoscale oxide-dispersion strengthened ferritic steels

Here, we present an investigation of Fe-14Cr-3W-0.4Y-0.4Zr-0.18Ti (wt.%) as a reduced-activation oxide-dispersion strengthened (ODS) ferritic steel, an alternative to the “14YWT” structural alloys designed for nuclear energy applications. Gas atomization reaction synthesis (GARS) was used to produce these Zr-modified powders with a non-equilibrium (metastable) phase that enable a heat treatment (delayed) route for producing nanoscale oxide-dispersion strengthening. In situ synchrotron X-ray diffraction and transmission electron microscopy were used to analyze phase evolution as a function of temperature and time, revealing formation of highly dispersed oxide nanoprecipitate phases at temperatures above those needed for powder consolidation and shaping of components. This would allow fabrication of net-shape parts using conventional powder-processing methods prior to thermal activation of a reaction producing nanocrystalline Y-(Ti, Zr)-O particles, with a size of 20 ± 7 nm. These results can inform processing of tubes, cladding, sheets, and plates for use in advanced fission and fusion reactors.

In-situ synchrotron X-ray diffraction↗

Towards uniformly dispersed battery electrode composite materials: Characteristics and performance

Battery electrodes are complex mesoscale systems comprised of electroactive components, conductive additives, and binders. In this report, methods for processing electrodes with dispersion of the components are described. To investigate the degree of material dispersion, a spin-coating technique was adopted to provide a thin, uniform layer that enabled observation of the morphology. Distinct differences in the distribution profile of the electrode components arising from individual materials physical affinities were readily identified. Hansen solubility parameter (HSP) analysis revealed pertinent surface interactions associated with materials dispersivity. Further studies demonstrated that HSPs can provide an effective strategy to identify surface modification approaches for improved dispersions of battery electrode materials. Specifically, introduction of surfactantlike functionality such as oleic acid (OA) capping and P3HT-conjugated polymer wrapping on the surface of nanomaterials significantly enhanced material dispersity over the composite electrode. The approach to the surface treatment on the basis of HSP study can facilitate design of composite electrodes with uniformly dispersed morphology and may contribute to enhancing their electrical and electrochemical behaviors. The conductivity of the composites and their electrochemical performance was also characterized. In conclusion, the study illustrates the importance of considering electronic conductivity, electron transfer, and ion transport in the design of environments incorporating active nanomaterials.

25 ENERGY STORAGE↗

Atypical water lattices and their possible relevance to the amorphous ices: A density functional study

Of the fifteen known crystalline forms of ice, eleven consist of a single topologically connected hydrogen bond network with four H-bonds at every O. The other four, Ices VI–VIII and XV, consist of two topologically connected networks, each with four H-bonds at every O. The networks interpenetrate but do not share H-bonds. This article presents two new periodic water lattice families whose topological connectivity is “atypical”: they consist of many two-dimensional layers that share no H-bonds. Layers are held together only by dispersion forces. Within each layer there are still four H-bonds at each O. Called “Hexagonal Bilayer Water” (HBW) and “Pleated Sheet Water” (PSW), they have computed densities of about 1.1 g/mL and 1.3 g/mL respectively, and nearest neighbor O-coordination is 4.5 to 5.5 and 6 to 8 respectively. Using density functional theory (BLYP-D/TZVP), various proton ordered forms of HBW and PSW are optimized and categorized. There are simple pathways connecting Ice-Ih to HBW and HBW to PSW. Their computed properties suggest similarities to the high density and very high density amorphous ices (HDA and VHDA) respectively. It is unknown whether HDA, VHDA, and Low Density Amorphous Ice (LDA) are fully disordered glasses down to the molecular level, or whether there is some short-range local order. Based on estimated radial distribution functions (RDFs), one proton ordered form of HBW matches HDA best. The idea is explored that HDA could contain islands with this underlying structure, and likewise, that VHDA could contain regions of PSW. A “microlattice model version 1” (MLM1) is presented as a device to compare key experimental data on the amorphous ices with these atypical structures and with a microlattice form of Ice-XI for LDA. Resemblances are found with the amorphs’ RDFs, densities, Raman spectra, and transition behaviors. There is not enough information in the static models to assign either a microlattice structure or a partial microlattice structure to any amorphous ice phase.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗