Search NASA⌕ Search

SEARCH · Search NASA

Results for “execution model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

A real-time distributed solid oxide electrolysis cell (SOEC) model for cyber-physical simulation

System integration and dynamic operability between SOEC and balance-of-plant (BoP) components are major technical challenges before realizing rapid load following of SOEC systems. Cyber-physical simulation (CPS) is a leading-edge digital engineering approach and is regarded as the next step beyond Digital Twins. CPS approach can be used to research SOEC system integration and develop dynamic controls prior to actual pilot testing without using a real SOEC. To seamlessly couple with BoP hardware and access non-observable operational parameters (e.g., local temperature gradient) during transients, a distributed one-dimensional (1D) real-time SOEC model was developed. Its real-time execution was demonstrated for 20 to 640 nodes at the fixed time step of 5 ms. A higher excess air ratio enabled smaller local temperature gradients on SOEC solid materials and faster transients upon current density step change from 0.15 to 0.55 A cm -2 . During the transients, the magnitude of the peak temperature gradient nearly doubled in 10 s from -3.5 to -5.9 °C cm -1 . This represents a significant operating risk that can impact the dynamic operability of SOEC systems. In addition, the local temperature gradient was found to change directions on all nodes in SOEC solid materials, with the greatest impact on the upstream nodes. The SOEC model was also tested at the thermal neutral voltage using actual process air flow parameters as variable model inputs. Variable process air temperatures were found to induce alternating local temperature gradients on SOEC solid materials. These are new operational mechanisms for SOEC degradation relevant for load following operational modes yet distinct from previous reports. To mitigate these unfavorable features, the SOEC can be operated at voltages that are slightly (±20 mV) deviated from the thermal neutral voltage. Here, the corresponding net thermal energy change was less than 1.6% of the electric power consumption. This 1D real-time SOEC model established the basis of cyber-physical simulation of SOEC hybrid systems.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2019

Models and methods for assessing the value of HVDC adn MVDC technologies in modern power grids (Annual Report, Executive Summary)

Evolution of today’s predominantly alternating current (ac) transmission grid in to mixed ac transmission – high-voltage direct current (HVdc) systems is expected with the decreasing costs of and advancements in power electronics technologies. The recent technological advancements include the development of more efficient and compact voltage source converters (VSCs) that can provide fast response. Because of their controllability and fast response, HVdc systems provide the ability to enhance reliability of the ac transmission grid through frequency support, voltage control, and congestion relief. The HVdc systems can also provide other ancillary services to enhance the economics and reliability of the ac transmission grids, and to optimize their performance. The tools, models, and methods developed to evaluate their benefits will be key enablers to understanding the value proposition introduced by the fast-acting HVdc systems. The main motivation of this work was to develop models and methods to explore and quantify the technical and economic benefits of HVdc systems and fast response VSC technologies in the future grid of United States. The models and methods explore the benefits of HVdc systems through provision of controlled active/reactive power and fast response. The fast response can provide much-needed multiobjective services to the grid (e.g., frequency response, voltage control) while moving blocks of energy. The models and methods can be applied to study other power electronics technologies and scenarios such as those undertaken in ongoing studies led by the North American Electric Reliability Corporation (NERC) Inverter-based Resource Performance Task Force (IRPTF). The IRPTF studies identify the problems associated with power electronics-based technologies as they are integrated in to the bulk power system (or the ac transmission system).

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS2016

Crash Testing and Simulation of a Cessna 172 Aircraft: Hard Landing Onto Concrete

A full-scale crash test of a Cessna 172 aircraft was conducted at the Landing and Impact Research Facility at NASA Langley Research Center during the summer of 2015. The purpose of the test was to evaluate the performance of Emergency Locator Transmitters (ELTs) that were mounted at various locations in the aircraft and to generate impact test data for model validation. A finite element model of the aircraft was developed for execution in LSDYNA to simulate the test. Measured impact conditions were 722.4-in/s forward velocity and 276-in/s vertical velocity with a 1.5deg pitch (nose up) attitude. These conditions were intended to represent a survivable hard landing. The impact surface was concrete. During the test, the nose gear tire impacted the concrete, followed closely by impact of the main gear tires. The main landing gear spread outward, as the nose gear stroked vertically. The only fuselage contact with the impact surface was a slight impact of the rearmost portion of the lower tail. Thus, capturing the behavior of the nose and main landing gear was essential to accurately predict the response. This paper describes the model development and presents test-analysis comparisons in three categories: inertial properties, time sequence of events, and acceleration and velocity time-histories.

Jackson, Karen E.↗
NASA NTRS2018

A Pilot Study to Determine MBSE Utility for Process Modeling of Complex Interfaces

Modeling a full system or a complete interface between systems in a MBSE environment is a very large task and not all organizations will benefit enough from using MBSE to offset the effort that is required to do this. Completely modeling a system or interface is not necessary to evaluate the utility of MBSE for a specific application or organization. A small pilot can be executed over a short period of time that only models small portions of a system or interface and, if structured properly, this pilot can successfully demonstrate the utility of MBSE for an organization before having to invest a larger amount of resources to fully implement and deploy MBSE. This paper documents one such pilot that was conducted for NASA’s Launch Services Program.

MBSE↗
NASA NTRS2018

A Pilot Study to Determine MBSE Utility for Process Modeling of Complex Interfaces

Modeling a full system or a complete interface between systems in a MBSE environment is a very large task and not all organizations will benefit enough from using MBSE to offset the effort that is required to do this. Completely modeling a system or interface is not necessary to evaluate the utility of MBSE for a specific application or organization. A small pilot can be executed over a short period of time that only models small portions of a system or interface and, if structured properly, this pilot can successfully demonstrate the utility of MBSE for an organization before having to invest a larger amount of resources to fully implement and deploy MBSE. This paper documents one such pilot that was conducted for NASA's Launch Services Program.

MBSE↗
NASA NTRS2018

A Pilot Study to Determine MBSE Utility for Process Modeling of Complex Interfaces

Modeling a full system or a complete interface between systems in a MBSE environment is a very large task and not all organizations will benefit enough from using MBSE to offset the effort that is required to do this. Completely modeling a system or interface is not necessary to evaluate the utility of MBSE for a specific application or organization. A small pilot can be executed over a short period of time that only models small portions of a system or interface and, if structured properly, this pilot can successfully demonstrate the utility of MBSE for an organization before having to invest a larger amount of resources to fully implement and deploy MBSE. This paper documents one such pilot that was conducted for NASA's Launch Services Program.

MBSE↗
DOE OSTI2026

TRACE Input Modernization

This work presents a Tom’s Obvious Minimal Language (TOML)-based representation of input for the US Nuclear Regulatory Commission’s TRAC/RELAP Advanced Computational Engine (TRACE) thermal hydraulics code. Implemented using the Workbench Analysis Sequence Processor (WASP), the approach maps traditional TRACE input structures to a hierarchical format composed of named parameters, typed values, and native data collections. The resulting representation preserves TRACE’s existing modeling capabilities while providing a modern, structured interface for model development and management. WASP further extends TOML through a file import directive that supports modular model composition and reusable input organization. In addition, WASP provides extended array data entry convenience with various data repeat and interpolation capabilities. Examples of the new TOML syntax are provided for major TRACE input categories, including hydraulic components, heat structures, control systems, and trip logic. The TOML representation establishes a foundation for improved validation, tooling, automation, and model maintainability while remaining compatible with existing TRACE workflows. To facilitate migration to the TOML-based input format, the TRACE executable now supports conversion of native TRACE input into an intermediate JSON representation. A Python utility subsequently transforms the JSON data into an equivalent TOML model. Lastly, the TRACE executable now supports execution using TOML-formatted input.

Lefebvre, Robert A. [Oak Ridge National Laboratory↗
DOE OSTI2016

Adaptive Impact-Driven Detection of Silent Data Corruption for HPC Applications

For exascale HPC applications, silent data corruption (SDC) is one of the most dangerous problems because there is no indication that there are errors during the execution. We propose an adaptive impact-driven method that can detect SDCs dynamically. The key contributions are threefold. (1) We carefully characterize 18 real-world HPC applications and discuss the runtime data features, as well as the impact of the SDCs on their execution results. (2) We propose an impact-driven detection model that does not blindly improve the prediction accuracy, but instead detects only influential SDCs to guarantee user-acceptable execution results. (3) Our solution can adapt to dynamic prediction errors based on local runtime data and can automatically tune detection ranges for guaranteeing low false alarms. Experiments show that our detector can detect 80-99.99% of SDCs with a false alarm rate less that 1% of iterations for most cases. The memory cost and detection overhead are reduced to 15% and 6.3%, respectively, for a large majority of applications.

Exascale HPC↗
DOE OSTI2023

SeeQ: A Programming Model for Portable Data-Driven Building Applications

This paper introduces SeeQ, a programming model and an abstraction framework that facilitates the development of portable data- driven building applications. Data-driven approaches can provide insights into building operations and guide decision-making to achieve operational objectives. Yet the configuration of such applications per building requires extensive effort and tacit knowledge. In SeeQ, we propose a portable programming model and build a software system that enables self-configuration and execution across diverse buildings. The configuration of each building is captured in a unified data model - in this paper, we work with the Brick ontology without loss of generality. SeeQ focuses on the distinction between the application logic and the configuration of an application against building-specific data inputs and systems. We test the proposed approach by configuring and deploying a diverse range of applications across five heterogeneous real-world buildings. The analysis shows the potential of SeeQ to significantly reduce the efforts associated with the delivery of building analytics.

analytics↗
NASA NTRS1990

Generation and analysis of large reliability models

An effort has been underway for several years at NASA's Langley Research Center to extend the capability of Markov modeling techniques for reliability analysis to the designers of highly reliable avionic systems. This effort has been focused in the areas of increased model abstraction and increased computational capability. The reliability model generator (RMG), a software tool which uses as input a graphical, object-oriented block diagram of the system, is discussed. RMG uses an automated failure modes-effects analysis algorithm to produce the reliability model from the graphical description. Also considered is the ASSURE software tool, a parallel processing program which uses the ASSIST modeling language and SURE semi-Markov solution technique. An executable failure modes-effects analysis is used by ASSURE. The successful combination of the power of graphical representation, automated model generation, and parallel computation leads to the conclusion that large system architectures can now be analyzed.

Aerospace electronics↗
DOE OSTI2019

OPEN-CODE, REAL-TIME EMULATION TESTBED OF GRID-CONNECTED TYPE-3 WIND TURBINE SYSTEM WITH HARDWARE VALIDATION

This paper presents the design and development of an open-code Type-3 wind turbine virtual-testbed for real-time simulations. The proposed testbed includes the bare code for all the models required to emulate a Type-3 wind turbine system: the Doubly-Fed Induction Generator (DFIG) dynamic model, single-mass drive train, wind turbine system, and average model of the back to back power. This testbed can be executed in PC-layer for offline simulations or can be executed in real-time on the National Instruments (NI)-CompactRIO (cRIO) platform. The discrete-time models are implemented on the Field Programmable Gate Array (FPGA), using LabVIEW, and validated against a physical hardware setup. The emulated stator and rotor currents and DC-link voltage are compared against physical measurements creating a validated platform independent from third-party models and suitable for applications in real-time. The proposed testbed is intended to be available to researchers, wind turbine manufacturers, and utility companies to perform tests using a validated platform to verify proposed control designs of DFIG wind turbines.

Ferrari Maglia, Max↗
NASA NTRS1993

Structural similitude and design of scaled down laminated models

The excellent mechanical properties of laminated composite structures make them prime candidates for wide variety of applications in aerospace, mechanical and other branches of engineering. The enormous design flexibility of advanced composites is obtained at the cost of large number of design parameters. Due to complexity of the systems and lack of complete design based informations, designers tend to be conservative in their design. Furthermore, any new design is extensively evaluated experimentally until it achieves the necessary reliability, performance and safety. However, the experimental evaluation of composite structures are costly and time consuming. Consequently, it is extremely useful if a full-scale structure can be replaced by a similar scaled-down model which is much easier to work with. Furthermore, a dramatic reduction in cost and time can be achieved, if available experimental data of a specific structure can be used to predict the behavior of a group of similar systems. This study investigates problems associated with the design of scaled models. Such study is important since it provides the necessary scaling laws, and the factors which affect the accuracy of the scale models. Similitude theory is employed to develop the necessary similarity conditions (scaling laws). Scaling laws provide relationship between a full-scale structure and its scale model, and can be used to extrapolate the experimental data of a small, inexpensive, and testable model into design information for a large prototype. Due to large number of design parameters, the identification of the principal scaling laws by conventional method (dimensional analysis) is tedious. Similitude theory based on governing equations of the structural system is more direct and simpler in execution. The difficulty of making completely similar scale models often leads to accept certain type of distortion from exact duplication of the prototype (partial similarity). Both complete and partial similarity are discussed. The procedure consists of systematically observing the effect of each parameter and corresponding scaling laws. Then acceptable intervals and limitations for these parameters and scaling laws are discussed. In each case, a set of valid scaling factors and corresponding response scaling laws that accurately predict the response of prototypes from experimental models is introduced. The examples used include rectangular laminated plates under destabilizing loads, applied individually, vibrational characteristics of same plates, as well as cylindrical bending of beam-plates.

Simitses, G. J.↗
DOE OSTI2024

Deep Learning Image Segmentation for Atmospheric Rivers

Abstract The identification of atmospheric rivers (ARs) is crucial for weather and climate predictions as they are often associated with severe storm systems and extreme precipitation, which can cause large impacts on society. This study presents a deep learning model, termed ARDetect, for image segmentation of ARs using ERA5 data from 1960 to 2020 with labels obtained from the TempestExtremes tracking algorithm. ARDetect is a convolutional neural network (CNN)-based U-Net model, with its structure having been optimized using automatic hyperparameter tuning. Inputs to ARDetect were selected to be the integrated water vapor transport (IVT) and total column water (TCW) fields, as well as the AR mask from TempestExtremes from the previous time step to the one being considered. ARDetect achieved a mean intersection-over-union (mIoU) rate of 89.04% for ARs, indicating its high accuracy in identifying these weather patterns and a superior performance than most deep learning–based models for AR detection. In addition, ARDetect can be executed faster than the TempestExtremes method (seconds vs minutes) for the same period. This provides a significant benefit for online AR detection, especially for high-resolution global models. An ensemble of 10 models, each trained on the same dataset but having different starting weights, was used to further improve on the performance produced by ARDetect, thus demonstrating the importance of model diversity in improving performance. ARDetect provides an effective and fast deep learning–based model for researchers and weather forecasters to better detect and understand ARs, which have significant impacts on weather-related events such as floods and droughts.

Galea, Daniel↗
NASA NTRS1998

The Deontic Transaction Model in Multi-Agent Normative Systems

In the area of multi-agent systems, much research is devoted to the coordination of the agents. There exist several issues, two of which are summarized. The first is that, although agents are said to be autonomous, they always react in a predictable way to each message, and they cannot decide to violate the conventions that are hard-wired into the protocol. In fact, there might be circumstances in which the agent violates a convention in order to realize a private goal that it considers to be more important. Another issue is that, if the protocols that agents use to react to the environment are fixed, they have no way to respond to changes. However, an important characteristic of agents is that they eon react to a changing environment. Although transaction models ([BOH92], [GR93]) evolved from the database domain, they establish a general execution paradigm that ideally covers all the subsystems invoked in a sequence of transactions. So transaction models apply to multi-agent systems. Recently, some research has been devoted to overcoming the limitations of the traditional transaction models which are suitable for conventional systems and focus on system integrity, e,g., [SJ97]. Here we solve above issues by turning to a deontic concept: obligation. In multi-agent systems, agents interact with each other according to norms, We use deontic logic ([And58], [Aqv84], [B C96], [JS94], [MW93]) to model norms. Here the norms prescribe how the agents ought to behave, but-- and this is essential-- they do not exclude the possibility of "bad" behavior (i.e., the actual behavior may deviate from the ideal), and so they also prescribe what should be done in circumstances of norm violation. Thus, we propose a new approach --- a deontic transaction model for multi-agent normative systems. Our approach improves the protocol of "abort/commit" of traditional transaction models to a protocol of "abort/exception/commit". In multi-agent normative systems, we can see the violation of a norm as an exception and how the other agents react to the violation as exception handling. This paper concentrates on our formal model.

Huang, Yonghua↗
NASA NTRS2020

Subscale Demonstration and Validation of the Hercules Ascent, Descent, and Entry Vehicle

This paper presents the results of a ten-week student led effort to build and test subscale models demonstrating and validating key capabilities for a space transportation system concept developed over the past 5 years at NASA Langley. This reusable concept, known as the Hercules Transportation System (HTS), is designed to support cislunar, lunar surface, and Mars surface missions or campaigns and offers unique operational capabilities. Until recently, much of the work on Hercules has been conceptual and has not been tested or validated by physical models. Our team, the 2019 NASA Academy at Langley Research Center, investigated and demonstrated the feasibility of the conceptual design by developing two unique scaled models. The goal of the first model was to collect six-component experimental wind tunnel data to validate theoretical predictions and inform future design iterations. Test results provided valuable insights on control surface effectiveness and static stability. The second model was designed to demonstrate the operational flexibility of Hercules by consistently executing vertical takeoff, horizontal translation, and landing. This paper describes the development and testing of both models.

Eytan Adler↗
NASA NTRSDate not supplied

NASA DEVELOP’s User-Centric Approach to Building Capacity to Use Earth Observations for Decision Making

The DEVELOP Program, part of NASA’s Applied Sciences, conducts 50-60 feasibility studies annually that center on user needs. Each project is tailored to its partner’s decision making processes with the goal of identifying and implementing opportunities for Earth observation data and information to be integrated into environmental decision making processes. These projects are conducted by a team of early career professionals through a 10-week term where the DEVELOP team rapidly iterates with partners culminating in a “recipe” for using NASA Earth observations. This presentation will introduce the DEVELOP model for user-centered design of projects, share the program's iterative approach to project execution, highlight multiple case studies, and lessons learned in the program’s model evolution.

Capacity Building↗
DOE OSTI2020

Accelerated version of NUBEAM capabilities in DIII-D using neural networks

A neural network model of the effects of neutral beam injection on DIII-D has been developed. The training and testing data used by the model have been generated by the NUBEAM module of TRANSP for experimental discharges from the 2018 DIII-D campaign. Using a principle component analysis to reduce the dimensionality of profile data, the model has been shown to reproduce the results of the Monte Carlo code NUBEAM with a high level of accuracy and an execution time orders of magnitude faster than the execution time of NUBEAM. Furthermore, this makes the neural network model uniquely suited to applications in model-based scenario planning (off-line) and active control (on-line), where a large number of simulation runs are required by the associated optimization tasks that need to be performed before and during the discharge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1979

VORTAB - A data-tablet method of developing input data for the VORLAX program

A method of developing an input data file for use in the aerodynamic analysis of a complete airplane with the VORLAX computer program is described. The hardware consists of an interactive graphics terminal equipped with a graphics tablet. Software includes graphics routines from the Tektronix PLOT 10 package as well as the VORTAB program described. The user determines the size and location of each of the major panels for the aircraft before using the program. Data is entered both from the terminal keyboard and the graphics tablet. The size of the resulting data file is dependent on the complexity of the model and can vary from ten to several hundred card images. After the data are entered, two programs READB and PLOTB, are executed which plot the configuration allowing visual inspection of the model.

Denn, F. M.↗