SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Tooling enables maintenance of close tolerances. Tooling includes guide that holds electrochemical drilling electrodes in proper relative alinement and guide-positioning fixture clamps directly on reference surfaces of strut. High precision achieved by positioning tooling anew on each strut before drilling: Tolerances of (0.008 mm) maintained in some details.
Finite element models were used to study the effects of notch angle variations on the stress state within an Iosipescu shear test speciment. These analytical results were also studied to determine the feasibility of using strain gage rosettes and a modified extensometer to measure shear strains in this test specimen. Analytical results indicate that notch angle variations produced only small differences in simulated shear properties. Both strain gage rosettes and the modified extensometer were shown to be feasible shear strain transducers for the test method. The Iosipoescu shear test fixture was redesigned to incorporate several improvements. These improvements include accommodation of a 50 percent larger specimen for easier measurement of shear train, a clamping mechanism to relax strict tolerances on specimen width, and a self contained alignment tool for use during specimen installation. A set of in-plane and interlaminar shear properties were measured for three graphite fabric/epoxy composites of T300/934 composite material. The three weave patterns were Oxford, 5-harness satin, and 8-harness satin.
Results are presented of tests conducted to evaluate a mobile work station/assembly fixture concept that would mechanically assist an astronaut in the on-orbit manual assembly of erectable truss-beams. The concept eliminates astronaut manual translation by use of a motorized work platform with foot restraints. The tests involved assembly of a tetrahedral truss-beam by a test subject in simulated zero gravity (neutral bouyancy in water). A three-bay truss-beam was assembled from 30 aluminum struts with quick-attachment structural joints. The results show that average on-orbit assembly rates of 2.1 struts per minute can be expected for struts of the size employed in these tests.
A hot-film constant-temperature anemometer (CTA) system was flight-tested and evaluated as a candidate sensor for determining boundary-layer transition on high-performance aircraft. The hot-film gage withstood an extreme flow environment characterized by shock waves and high dynamic pressures, although sensitivity to the local total temperature with the CTA indicated the need for some form of temperature compensation. A temperature-compensation scheme was developed and two CTAs were modified and flight-tested on the F-104/Flight Test Fixture (FTF) facility at a variety of Mach numbers and altitudes, ranging from 0.4 to 1.8 and 5,000 to 40,000 ft respectively.
An experimental and analytical study was conducted of the postbuckling response and failure characteristics of 8-, 16-, and 24-ply unstiffened graphite/epoxy plates under shear loading, including orthotropic, quasi-orthotropic, entirely +, -45 deg ply, and (0/90)s-class plates. Postbuckling stiffness is noted to be influenced by the stacking sequence and by the inplane boundary condition imposed on the test section by a picture frame test fixture. The ratio of failure load to buckling load was higher for specimens that had higher width-to-thickness ratios. It is noted that high displacement gradients may induce transverse shear stresses, and that delamination was the failure mechanism for many of the 8-ply specimens. An adhesive failure between the composite specimen and metal edge reinforcements initiated failure of the 16- and 24-ply specimens.
The NASA Langley Research Center has developed bonding concepts for aerospace composite materials which employ induction heating to directly apply heat to the bond line and/or adherends without simultaneously heating the entire structure, supports, and fixtures of a bonding assembly. These methods have demonstrated bonding process time reductions of two to three orders of magnitude, by comparison with conventional press molding. Attention is presently given to rapid adhesive bonding for lap shear specimens for aerospace panel bonding or field repair, as well as for the field repair requirements of metallic and advanced polymeric matrix composite structures.
The study investigated the accumulation of transverse matrix cracks and the resultant loss of torsional, extensional, and bending stiffnesses in 8 layer 0.5 in. diameter crossply tubes subjected to thermal cycling. The tubes were graphite-epoxy and the temperature range during cycling was -250 to 200 F. The effect of fiber and matrix properties was investigated through the use of T300 and P75S fibers and 934 and CE339 resins. The study considered 0, 10, 50, 100, 300, and 500 thermal cycles. Photomicrographs, X-rays, and edge replication were used to evaluate cracking. Special loading fixtures were used to measure stiffness changes. An important finding was that for the tubes studied, even with extensive cracking, the bending and extensional stiffnesses were not affected. The torsional stiffness, however, was strongly affected.
Significant improvements in engine readiness with reductions in maintenance costs and turn-around times can be achieved with an engine condition monitoring systems (CMS). The CMS provides health status of critical engine components, without disassembly, through monitoring with advanced sensors. Engine failure reports over 35 years were categorized into 20 different modes of failure. Rotor bearings and turbine blades were determined to be the most critical in limiting turbopump life. Measurement technologies were matched to each of the failure modes identified. Three were selected to monitor the rotor bearings and turbine blades: the isotope wear detector and fiberoptic deflectometer (bearings), and the fiberoptic pyrometer (blades). Signal processing algorithms were evaluated for their ability to provide useful health data to maintenance personnel. Design modifications to the Space Shuttle Main Engine (SSME) high pressure turbopumps were developed to incorporate the sensors. Laboratory test fixtures have been designed for monitoring the rotor bearings and turbine blades in simulated turbopump operating conditions.
Notched and unnotched geometries at 16, 32, and 64-ply thicknesses of a 90/45/0-45 (ns) laminate and a 45/0/-45/90 (ns) laminate were tested in compression-compression fatigue. The fatigue life and the initiation, type, and progression of damage were determined. Interlaminar stresses generated at straight, free edges of axially loaded laminates were used to interpret the test results. The fatigue lives of the notched specimens did not appear to be a strong function of laminate stacking sequence or specimen thickness. The stress concentration at the hole dominated over the interlaminar stresses at the straight free edge. The unnotched specimens of the 90/45/0/-45 (ns) laminate with tensile interlaminar normal stresses delaminated more readily than did the 45/0/-45/90 (ns) laminate with compressive interlaminar normal stress. The life of the 16-ply unnotched specimens was lower than the 32and 64-ply specimens. Delaminations were located at the interface where the maximum shear stress occurred regardless of the sense or magnitude of the interlaminar normal stress. An antibuckling fixture was effective in preventing out-of-plane motion without overconstraining the specimen.
Vibration spectrum of test machine adjusted to that observed in operation. Test specimen placed in test fixture and attached to shaker. Shaker initially operated at one-quarter full level of input spectrum to prevent overloading. Short vibration test run, and specimen response compared to control spectrum. Imput spectrum then adjusted until response resembles control spectrum.
Frequent workpiece repositioning made easier. Air-bearing table facilitates movement of heavy workpiece during machining or between repeated operations at different positions. Table assembly consists of workpiece supporting fixture riding on air bearing. Table especially useful for inertia welding, in which ease of mobility is important.
Laser cutting technique produces narrow, precise, fast, and repeatable cuts in thin nickel-allow bellows material. Laser cutting operation uses intense focused beam to melt material and assisting gas to force melted material through part thickness, creating void. When part rotated or moved longitudinally, melting and material removal continuous and creates narrow, fast, precise, and repeatable cut. Technique used to produce cuts of specified depths less than material thickness. Avoids distortion, dents, and nicks produced in delicate materials during lathe trimming operations, which require high cutting-tool pressure and holding-fixture forces.
Large holes in polyurethane foam insulation repaired reliably by simple method. Little skill needed to apply method, used for overhead repairs as well as for those in other orientations. Plug positioned in hole to be filled and held in place with mounting fixture. Fresh liquid foam injected through plug to bond it in place. As foam cures and expands, it displaces plug outward. Protrusion later removed.
Adhesive bonding in the aerospace industry typically utilizes autoclaves or presses which have considerable thermal mass. As a consequence, the rates of heatup and cooldown of the bonded parts are limited and the total time and cost of the bonding process are often relatively high. Many of the adhesives themselves do not inherently require long processing times. Bonding could be performed rapidly if the heat was concentrated in the bond lines or at least in the adherends. Rapid Adhesive Bonding concepts are developed to utilize induction heating techniques to provide heat directly to the bond line and/or adherends without heating the entire structure, supports, and fixtures of a bonding assembly. Bonding times for specimens can be cut by a factor of 10 to 100 compared to standard press or autoclave bonding. The development of Rapid Adhesive Bonding for lap shear specimens (per ASTM D1002 and D3163), for aerospace panel or component bonding, and for field repair needs of metallic and advanced fiber reinforced polymeric-matrix composite structures is reviewed. Equipment and procedures are described for bonding and repairing thin sheets, simple geometries, and honeycomb core panels.
Large deformation response of simple composite structural elements to intense dynamic loadings is studied by focusing on the response of beams. Overall goals are to: design a simple test fixture to introduce crash related bending loads in beams; determine any difference between large deformation static and large deformation dynamic response; determine the influence of laminate stacking arrangements on the dynamic response, failure mode, and energy absorbed; and predict the dynamic response. Twelve different laminate orientations were investigated. Modeling of the response was done with an existing finite element program. The program computed nonlinear transient response analysis of a structure objected to a time varying load.
A hot-film constant-temperature anemometer (CTA) system was flight-tested and evaluated as a candidate sensor for determining boundary-layer transition on high-performance aircraft. The hot-film gage withstood an extreme flow environment characterized by shock waves and high dynamic pressures, although sensitivity to the local total temperature with the CTA indicated the need for some form of temperature compensation. A temperature-compensation scheme was developed and two CTAs were modified and flight-tested on the F-104/Flight Test Fixture (FTF) facility at a variety of Mach numbers and altitudes, ranging from 0.4 to 1.8 and 5,000 to 40,000 ft respectively.
A monolithic gain control amplifier for Ka-band has been developed based on 0.25 micron-gate-length dual-gate FETs fabricated on ion-implanted material. A single-stage monolithic amplifier gives a gain of 6 dB at 31 GHz including fixture losses with a gain control range of over 20 dB. The device and IC design and fabrication are described.
Single-ended notch design facilitates accurate measurements of crack progression. Novel test specimen and novel loading fixture and fracture testing of materials under Mode II, or sliding-mode, loading. Testing required for analysis of failures in structural materials, bearings, and the like.