Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

An Improved Technique for the Preparation of Mounted or Unmounted Carbon/Epoxy Specimens

As carbon/epoxy materials became more prevalent in the aerospace industry, microstructural analysis demanded specimen preparation techniques that led to better polished surfaces, achievable in a shorter time, and using fewer steps. The desire to use image analysis for material characterization also helped drive the goal for defect free surfaces. At NASA-Langley (LaRC), carbon/epoxy specimens had been historically prepared in 1 inch diameter Bakelite mounts. Carbon/epoxy specimens that were 1/8 to 1/4 inch thick were not affected by the heat and pressure required for mounting in Bakelite, however thinner specimens were crushed during mounting. A two-part room temperature curing epoxy was chosen as an alternative but sometimes voids developed between the specimen and the mounting material. This was prevented by either heating the epoxy to 140 degrees F to lower the viscosity of the epoxy or by using a vacuum impregnation apparatus. Both techniques helped facilitate flow and allowed the epoxy to penetrate crevices.

Edahl, Robert A., Jr.↗
NASA NTRS2024

On the Role of Friction and Particle Size Distribution in Granular Packings

Packing of particles in a disordered arrangement has tremendous significance in both condensed matter physics and engineering applications. The last three decades have seen remarkable progress in our understanding of the physics of granular packings that has been largely facilitated by a rapid growth in the power of modern computers. Although granular packings are ubiquitous in diverse natural settings, from clogging of powders in hoppers to the crowding of living cells, a significant motivation for modeling granular packings has emerged from a proposal that the transition from a fluid-like state to a solid-like state of a granular material upon increasing volume fraction, called jamming, is intimately related to the origins of glass transition in thermal systems. As such, a majority of modeling efforts have focused on the jamming behavior of an idealized granular material: frictionless, monodisperse sphere. While such studies have illuminated the rich physics of jamming, granular materials in nature and engineering practice are rarely frictionless or monodisperse. The analogous research on the packing of these ‘real-world’ granular materials is still not fully developed. Besides requiring the exploration of a huge parameter space, three key computational considerations have inhibited their modeling: (i) traditional computational methods are not adept at simulating mechanically-stable packings of frictional particles near the jamming transition; (ii) standard algorithms of contact detection in discrete element methods are impractical to simulate granular packings with a wide distribution of particle sizes; (iii) a lack of well-established contact mechanics models of friction that can accurately reproduce experimental data. This chapter will review the latest computational advances to simulate the jamming of size-dispersed frictional particles, and describe the rich microstructural diversity that emerges in their packings.

granular↗
NASA NTRS2013

Fracture in Phenolic Impregnated Carbon Ablator

This paper describes the development of a novel technique to understand the failure mechanisms inside thermal protection materials. The focus of this research is on the class of materials known as phenolic impregnated carbon ablators. It has successfully flown on the Stardust spacecraft and is the thermal protection system material chosen for the Mars Science Laboratory and SpaceX Dragon spacecraft. Although it has good thermal properties, structurally, it is a weak material. To understand failure mechanisms in carbon ablators, fracture tests were performed on FiberForm(Registered TradeMark) (precursor), virgin, and charred ablator materials. Several samples of these materials were tested to investigate failure mechanisms at a microstructural scale. Stress-strain data were obtained simultaneously to estimate the tensile strength and toughness. It was observed that cracks initiated and grew in the FiberForm when a critical stress limit was reached such that the carbon fibers separated from the binder. However, both for virgin and charred carbon ablators, crack initiation and growth occurred in the matrix (phenolic) phase. Both virgin and charred carbon ablators showed greater strength values compared with FiberForm samples, confirming that the presence of the porous matrix helps in absorbing the fracture energy.

Agrawal, Parul↗
NASA NTRS2009

In-Situ NDE Characterization of Kevlar and Carbon Composite Micromechanics for Improved COPV Health Monitoring

This project is a subtask of a multi-center project to advance the state-of-the-art by developing NDE techniques that are capable of evaluating stress rupture (SR) degradation in Kevlar/epoxy (K/Ep) composite overwrapped pressure vessels (COPVs), and damage progression in carbon/epoxy (C/Ep) COPVs. In this subtask, acoustic emission (AE) data acquired during intermittent load hold tensile testing of K/Ep and C/Ep composite tow materials-of-construction used in COPV fabrication were analyzed to monitor progressive damage during the approach to tensile failure. Insight into the progressive damage of composite tow was gained by monitoring AE event rate, energy, source location, and frequency. Source location based on arrival time data was used to discern between significant AE attributable to microstructural damage and spurious AE attributable to background and grip noise. One of the significant findings was the observation of increasing violation of the Kaiser effect (Felicity ratio < 1.0) with damage accumulation.

Waller, Jess M.↗
NASA NTRS1990

Thermal Conductivity and Temperature Limits of Electron-Beam Physical-Vapor-Deposited ZrO2-7wt%Y2O3 Thermal Barrier Coating

The electron-beam physical-vapor-deposited (EB-PVD) ZrO2-7wt%Y2O3 thermal barrier coating has been widely used to protect engine hot section components in modem aircraft engines. Thermal conductivity and the conductivity increases due to sintering and phase changes are important coating design parameters. There is a need to characterize the coating thermal conductivity behavior and temperature limits, in order to potentially take full advantage of the coating capability. In addition, since the ZrO2-7wt%Y2O3 coating is often used as a baseline coating for the development of advanced lower thermal conductivity and higher temperature capability coatings, a thorough evaluation of the coating conductivity behavior at future higher engine operating temperatures will be useful for more accurately assessing the benefit gained from the new coating systems. In this study, thermal conductivity behavior of EB-PVD ZrO2-7wt%Y2O3 coating has been systematically investigated as a function of temperature (up to 2600 F) and time under steady-state and cyclic test conditions using a laser heat-flux technique. Thermal conductivity change kinetics were determined under realistic engine high temperature thermal gradient conditions, and correlated to the coating microstructural and phase changes. The thermal conductivity prediction models have been established in terms of heat flux, time, and testing temperatures.

Zhu, Dongming↗
NASA NTRS2019

Additive Manufacturing of Multi-Material Systems for Aerospace Applications

Additive manufacturing methods for producing single materials are rapidly improving. The resulting material properties and microstructures are becoming more comparable to those of conventionally fabricated materials. However, the need for multi-functional and complex structures and components requires additional innovations in manufacturing such as multi-material and hybrid additive manufacturing approaches. Additive manufacturing machines with multiple print capabilities and combinations of AM, machining, and conventional processing methods will further open up design spaces and possibilities. In this presentation, several examples of the needs and methods for multi-material fabrication will be discussed with a focus on aerospace applications. Direct printing of silver coils in conjunction with fused deposition modeling, machined parts, and, binder jetting is being developed for innovative stator designs. Binder jetting of silicon-based materials with powder bed additions is being developed for heat exchanger applications. Additive manufacturing of bi-material systems is being pursued to fabricate lightweight, integrated, multifunctional structures.

multi-materials↗
NASA NTRS1986

Plastic deformation - Its role in fatigue crack propagation

Recognizing the fact that the effective driving force Delta-K(eff) determines the fatigue crack propagation (FCP) rate and that the shear strain, which is considered to develop due to an occurrence of crack closure, primarily contributes to the plastic deformation, an effort is made here to elucidate the role of plastic deformation in FCP by developing a correlation between the Delta-K(eff) and the applied driving force (Delta-K) with shear strain as variable. The disparity between Delta(K)eff) and Delta-K, which apparently increases with shear strain level, persists at lower values of Delta-K. This suggests a strong influence of the degree of localized deformation on the FCP rates in the near threshold level. Hence, an improvement of FCP rates in the near threshold level should follow an effort that promotes the plastic deformation near the crack tip to a greater degree. This approach could explain the effect of the grain size, microstructure, environment, R-ratio and crack size on the near-threshold FCP rates.

Mazumdar, P. K.↗
NASA NTRS1951

Flight Camera for Photographing Cloud Droplets in Natural Suspension in the Atmosphere

A camera designed for use in flight has been developed by the NACA Lewis laboratory t o photograph cloud droplets in their natural suspension in the atmosphere. A magnification of 32 times is employed to distinguish for measurement purposes all sizes of droplets greater than 5 microns in diameter. Photographs can be taken at flight speeds up to 150 miles per hour at 5-second intervals, A field area of 0.025 square inch is photographed on 7-inch-width roll film accommodating 40 exposures on an 18-foot length. Flight tests conducted in cumulus clouds have shown that approximate droplet-size distribution studies can be obtained and that a studies of the microstructure and physics of clouds can be made with the camera.

Mccullough, Stuart↗
NASA NTRS2019

Effects of Surface Treatments on Stainless Steel 316 Exposed to Potable Water Containing Silver Disinfectant

Silver has been selected as the forward disinfectant candidate for potable water systems in future space exploration missions. To develop a reliable antibacterial system that requires minimal maintenance, it is necessary to address relevant challenges to preclude problems for future missions. One such challenge is silver depletion in potable water systems. When in contact with various materials, silver ions can be easily reduced to silver metal or form insoluble compounds. The same chemical properties that make ionic silver a powerful antimicrobial agent also result in its quick inactivation or depletion in various environments. Different metal surface treatments, such as thermal oxidation and electropolishing, have been investigated for their effectiveness in reducing silver disinfectant depletion in potable water. However, their effects on the metal surface microstructure and chemical resistance have not often been included in the studies. This paper reports the effects of surface treatments on stainless steel 316 (SS316) exposed to potable water containing silver ion as a disinfectant. Early experimental results showed that thermal oxidation, when compared with electropolishing, resulted in a thicker oxide layer but compromised the corrosion resistance of SS316.

Li, Wenyan↗
NASA NTRS1977

An experimental P/M wrought superalloy for advanced temperature service

A study was undertaken in order to adapt IIB-11 (an experimental wrought superalloy with high temperature strength) to manufacture via powder metallurgy techniques, and to improve its microstructural stability. Three compositional modifications were produced and evaluated. Among the conclusions reached it was found that: (1) IIB-11 having a low C and low Hf alloy content is suitable for advanced temperature turbine disks, and is applicable to fabrication by powder metallurgy techniques, (2) IIB-11, when compared to modifications with higher C and/or higher Hf, is somewhat weaker in tension at intermediate temperatures but superior in tensile ductility, rupture strength and ductility, and stability during long-time heating, (3) increases in the cross-rolling temperature increase the grain size of alloys after solution treatment, and (4) both the lower C modifications develop larger grain sizes than the higher C modification.

Miner, R. V.↗
NASA NTRS2009

Development of High Temperature Dissimilar Joint Technology for Fission Surface Power Systems

NASA is developing fission surface power (FSP) system technology as a potential option for use on the surface of the moon or Mars. The goal is to design a robust system that takes full advantage of existing materials data bases. One of the key components of the power conversion system is the hot-side Heat Exchanger (HX). One possible design for this heat exchanger requires a joint of the dissimilar metals 316L stainless steel and Inconel 718, which must sustain extended operation at high temperatures. This study compares two joining techniques, brazing and diffusion bonding, in the context of forming the requisite stainless steel to superalloy joint. The microstructures produced by brazing and diffusion bonding, the effect of brazing cycle on the mechanical tensile properties of the alloys, and the strength of several brazed joints will be discussed.

Locci, Ivan E.↗
NASA NTRSDate not supplied

Feasibility Study to Dissolve Additively Manufactured Inconel 718 Support Structures

Additive manufacture (AM) component design face constrains due to support structure removal. Interior passages or delicate geometries require supports yet cannot be removed without compromising the design or complicating post-processing. A process was developed to dissolve metal AM supports where a sensitizing agent is applied post-build. During stress relief the sensitizing agent diffuses into the surface and alters the chemical composition of the top 100 to 200 μm. During an electrochemical dissolution process the sensitized region is susceptible to corrosion/dissolution and the etching reaction self-terminates once the sensitized region is dissolved. Support thickness varies from 80 to 200 μm, resulting in total dissolution or sufficiently weakened to facilitate removal. The objective of this project was to demonstrate a support structure dissolution process for IN718 components built using AM and to characterize the impact on mechanical properties, microstructure, and surface finish.

Omar R Mireles↗
NASA NTRS1979

Development of silicon nitride of improved toughness

The application of reaction sintered Si2N4 energy absorbing surface layers to hot-pressed Si3N4 was investigated. The surface layer was formed by in-place nitridation of silicon powder. It was found that reaction sintered Si3N4 layers of 1 mm thickness, fabricated from either -100, +200, -200, or -325 mesh Si powder and nitrided in 96% N2/4% H2 so that approximately 20-25 vol % unnitrided Si remained in the layer, resulted in a sevenfold increase in ballistic impact resistance of a 0.64 cm thick hot-pressed SI3N4 substrate from RT 1370 C. Both NC-132 SI3N4, with MgO additive, and NCX-34 Si3N4, with Y2O3 additive, were evaluated as substrate material. The finer grain size -200 and -325 mesh nitrided Si layers were for their smoothness and relatively high density. It was found that nitriding in N2/H2 mixtures, rather than pure N2, resulted in a microstructure that did not substantially degrade the strength of the hot-pressed Si3N4 substrate. Thermal cycling tests on the RSSN/HPSN combinations from 200 C to 1370 C for 75 cycles in air did not degrade the impact resistance nor the interfacial bonding, although a large amount of internal silica formation occurred within the RSSN layer. Mach 0.8, 5 hr, hot gas erosion tests showed no surface recession of RSSN layers at 1200 C and slight surface recession at 1370 C.

Brennan, J. J.↗
NASA NTRS1996

Development and Processing of Nickel Aluminide-Carbide Alloys

With the upper temperature limit of the Ni-based superalloys attained, a new class of materials is required. Intermetallics appear as likely candidates because of their attractive physical properties. With a relatively low density, high thermal conductivity, excellent oxidation resistance, high melting point, and simple crystal structure, nickel aluminide (NiAl) appears to be a potential candidate. However, NiAl is limited in structural applications due to its low room temperature fracture toughness and poor elevated temperature strength. One approach to improving these properties has been through the application of eutectic composites. Researchers have shown that containerless directional solidification of NiAl-based eutectic alloys can provide improvement in both the creep strength and fracture toughness. Although these systems have shown improvements in the mechanical properties, the presence of refractory metals increases the density significantly in some alloys. Lower density systems, such as the carbides, nitrides, and borides, may provide NiAl-based eutectic structure. With little or no information available on these systems, experimental investigation is required. The objective of this research was to locate and develop NiAl-carbide eutectic alloys. Exploratory arc-melts were performed in NiAl-refractory metal-C systems. Refractory metal systems investigated included Co, Cr, Fe, Hf, Mo, Nb, Ta, Ti, W, and Zr. Systems containing carbides with excellent stability (i.e.,HfC, NbC, TaC, TiC, and ZrC) produced large blocky cubic carbides in an NiAl matrix. The carbides appeared to have formed in the liquid state and were randomly distributed throughout the polycrystalline NiAl. The Co, Cr, Fe, Mo, and W systems contained NiAl dendrites with a two-phase interdendritic microconstituent present. Of these systems, the NiAl-Mo-C system had the most promising microstructure for in-situ composites. Three processing techniques were used to evaluate the NiAl-Mo-C system: arc-melting, slow cooling, and containerless directional solidification. Arc-melting provided a wide range of compositions in an economical and simple fashion. The slow cooled ingots provided larger ingots and slower cooling rates than arc-melting. Directional solidification was used to produce in-situ composites consisting of NiAl reinforced with molybdenum carbides.

Newport, Timothy Scott↗
NASA NTRS2007

Early Proterozoic (2.04 GA) Phoshorites of Pechenga Greenstone Belt and Their Origin

No principal differences have been found between microfossils described from Cambrian and Phanerozoic and the 2000 Ma phosphorites. Numerous samples revealed diverse microbial microstructures interpreted as cyanobacterial mats consisting of filamentous (1-3 microns in diameter, 20 microns in length), coccoidal (0.8-1.0 microns) and ellipsoidal or rod-shaped microfossils (0.8 microns in diameter, around 2 microns in length) which morphologically resemble modern Microcoleus and Siphonophycus, Thiocapsa, and Rhabdoderma, respectively, reported from alkali ne or saline environment_ The sequence of the early Palaeoproterozoic events which point to a significant oxidation of the hydrosphere, including the formation of phosphorites and changes in the phosphorous cycle, mimics the sequence which was repeated at the Neoproterozoic-Cembrian transition, implying that oxidation of the terrestrial atmosphere-hydrosphere system experienced an irregular cyclic development.

Rozanov, Alexei Yu.↗
NASA NTRS2011

Characterization of Electron Beam Free-Form Fabricated 2219 Aluminum and 316 Stainless Steel

Researchers at NASA Langley Research Center have developed an additive manufacturing technology for ground and future space based applications. The electron beam free form fabrication (EBF3) is a rapid metal fabrication process that utilizes an electron beam gun in a vacuum environment to replicate a CAD drawing of a part. The electron beam gun creates a molten pool on a metal substrate, and translates with respect to the substrate to deposit metal in designated regions through a layer additive process. Prior to demonstration and certification of a final EBF3 part for space flight, it is imperative to conduct a series of materials validation and verification tests on the ground in order to evaluate mechanical and microstructural properties of the EBF3 manufactured parts. Part geometries of EBF3 2219 aluminum and 316 stainless steel specimens were metallographically inspected, and tested for strength, fatigue crack growth, and fracture toughness. Upon comparing the results to conventionally welded material, 2219 aluminum in the as fabricated condition demonstrated a 30% and 16% decrease in fracture toughness and ductility, respectively. The strength properties of the 316 stainless steel material in the as deposited condition were comparable to annealed stainless steel alloys. Future fatigue crack growth tests will integrate various stress ranges and maximum to minimum stress ratios needed to fully characterize EBF3 manufactured specimens.

Ekrami, Yasamin↗
NASA NTRS1997

Microstructure and Mechanical Properties of Vacuum Plasma Sprayed Cu-8Cr-4Nb

This paper compares the tensile properties of Cu-8Cr-4Nb material produced by VPS to material previously produced by extrusion. The microstructure of the VPS material is also presented. The combustion chamber liner of rocket motors represents an extreme materials application. The liner hot wall is exposed to a 2760 C (5000 F) flame while the cold side is exposed to cryogenic hydrogen liquid. Materials for use in the combustion chamber liner require a combination of high temperature strength, creep resistance, and low cycle fatigue resistance along with high thermal conductivity. The hot side is also subject to localized cycles between reducing and oxidizing environments that degrade the liner by a process called blanching. A new Cu-8 at.% Cr-4 at% Nb (Cu-8Cr-4Nb) alloy has been developed at NASA Lewis Research Center as a replacement for the currently used alloy, NARloy-z (Cu-3 wt.% Ag-0.5 wt.% Zr). The alloy is strengthened by a fine dispersion of Cr2Nb particles. The alloy has better mechanical properties than NARloy-Z while retaining most of the thermal conductivity of pure copper. The alloy has been successfully consolidated by extrusion and hot isostatic pressing (HIPing). However, vacuum plasma spraying (VPS) offers several advantages over prior consolidation methods. VPS can produce a near net shape piece with the profile of the liner. In addition, oxidation resistant and thermal barrier coatings can be incorporated as an integral part of the liner hot wall during the VPS deposition. The low oxygen VPS Cu-8Cr-4Nb exhibits a higher strength than Cu-8Cr-4Nb produced by extrusion at elevated temperatures and a comparable strength at room temperature. Moduli and ductility were not significantly different. However, the ability to produce parts to near-net shape and maintain the good elevated temperature tensile properties of the extruded Cu-8Cr-4Nb makes VPS an attractive processing method for fabricating rocket engine combustion liners.

Holmes, Richard↗
NASA NTRS1976

Heat treating of a lamellar eutectic alloy (gamma/gamma prime + delta)

Eutectic superalloys are being developed at several laboratories for application as aircraft gas turbine airfoils. One such alloy was subjected to several heat treatments to determine if its mechanical properties could be improved. It was found that by partially dissolving the alloy at 1210 C and then aging at 900 C the tensile strength can be increased about 12 percent at temperatures up to 900 C. At 1040 C no change in tensile strength was observed. Times to rupture were measured between 760 and 1040 C and were essentially the same or greater than for as-grown material. Tensile and rupture ductility of the alloy are reduced by heat treatment. Photographs of the microstructure are shown.

Tewari, S. N.↗