Search NASA⌕ Search

SEARCH · Search NASA

Results for “module efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

A forward bias method for lag correction of an a-Si flat panel detector

Purpose: Digital a-Si flat panel (FP) x-ray detectors can exhibit detector lag, or residual signal, of several percent that can cause ghosting in projection images or severe shading artifacts, known as the radar artifact, in cone-beam computed tomography (CBCT) reconstructions. A major contributor to detector lag is believed to be defect states, or traps, in the a-Si layer of the FP. Software methods to characterize and correct for the detector lag exist, but they may make assumptions such as system linearity and time invariance, which may not be true. The purpose of this work is to investigate a new hardware based method to reduce lag in an a-Si FP and to evaluate its effectiveness at removing shading artifacts in CBCT reconstructions. The feasibility of a novel, partially hardware based solution is also examined. Methods: The proposed hardware solution for lag reduction requires only a minor change to the FP. For pulsed irradiation, the proposed method inserts a new operation step between the readout and data collection stages. During this new stage the photodiode is operated in a forward bias mode, which fills the defect states with charge. A Varian 4030CB panel was modified to allow for operation in the forward bias mode. The contrast of residual lag ghosts was measured for lag frames 2 and 100 after irradiation ceased for standard and forward bias modes. Detector step response, lag, SNR, modulation transfer function (MTF), and detective quantum efficiency (DQE) measurements were made with standard and forward bias firmware. CBCT data of pelvic and head phantoms were also collected. Results: Overall, the 2nd and 100th detector lag frame residual signals were reduced 70%-88% using the new method. SNR, MTF, and DQE measurements show a small decrease in collected signal and a small increase in noise. The forward bias hardware successfully reduced the radar artifact in the CBCT reconstruction of the pelvic and head phantoms by 48%-81%. Conclusions: Overall, the forward bias method has been found to greatly reduce detector lag ghosts in projection data and the radar artifact in CBCT reconstructions. The method is limited to improvements of the a-Si photodiode response only. A future hybrid mode may overcome any limitations of this method.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Cone beam breast CT with a high pitch (75 μm), thick (500 μm) scintillator CMOS flat panel detector: Visibility of simulated microcalcifications

Purpose: To measure and investigate the improvement of microcalcification (MC) visibility in cone beam breast CT with a high pitch (75 μm), thick (500 μm) scintillator CMOS/CsI flat panel detector (Dexela 2923, Perkin Elmer).Methods: Aluminum wires and calcium carbonate grains of various sizes were embedded in a paraffin cylinder to simulate imaging of calcifications in a breast. Phantoms were imaged with a benchtop experimental cone beam CT system at various exposure levels. In addition to the Dexela detector, a high pitch (50 μm), thin (150 μm) scintillator CMOS/CsI flat panel detector (C7921CA-09, Hamamatsu Corporation, Hamamatsu City, Japan) and a widely used low pitch (194 μm), thick (600 μm) scintillator aSi/CsI flat panel detector (PaxScan 4030CB, Varian Medical Systems) were also used in scanning for comparison. The images were independently reviewed by six readers (imaging physicists). The MC visibility was quantified as the fraction of visible MCs and measured as a function of the estimated mean glandular dose (MGD) level for various MC sizes and detectors. The modulation transfer functions (MTFs) and detective quantum efficiencies (DQEs) were also measured and compared for the three detectors used.Results: The authors have demonstrated that the use of a high pitch (75 μm) CMOS detector coupled with a thick (500 μm) CsI scintillator helped make the smaller 150–160, 160–180, and 180–200 μm MC groups more visible at MGDs up to 10.8, 9, and 10.8 mGy, respectively. It also made the larger 200–212 and 212–224 μm MC groups more visible at MGDs up to 7.2 mGy. No performance improvement was observed for 224–250 μm or larger size groups. With the higher spatial resolution of the Dexela detector based system, the apparent dimensions and shapes of MCs were more accurately rendered. The results show that with the aforementioned detector, a 73% visibility could be achieved in imaging 160–180 μm MCs as compared to 28% visibility achieved by the low pitch (194 μm) aSi/CsI flat panel detector. The measurements confirm that the Hamamatsu detector has the highest MTF, followed by the Dexel detector, and then the Varian detector. However, the Dexela detector, with its thick (500 μm) CsI scintillator and low noise level, has the highest DQE at all frequencies, followed by the Varian detector, and then the Hamamatsu detector. The findings on the MC visibility correlated well with the differences in MTFs, noise power spectra, and DQEs measured for these three detectors.Conclusions: The authors have demonstrated that the use of the CMOS type Dexela detector with its high pitch (75 μm) and thick (500 μm) CsI scintillator could help improve the MC visibility. However, the improvement depended on the exposure level and the MC size. For imaging larger MCs or scanning at high exposure levels, there was little advantage in using the Dexela detector as compared to the aSi type Varian detector. These findings correlate well with the higher measured DQEs of the Dexela detector, especially at higher frequencies.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Sharp Drop in the Mobility of Holes with a Decrease in Their Two-Dimensional Concentration by an External Voltage in Boron δ-Doped Diamond Layers

It is shown, both analytically and numerically, that the hole mobility in boron δ-doped (i.e., with a thickness on the order of several lattice constants) diamond layers drops with a decrease in their two-dimensional concentration during depletion of the δ-doped layer by an external voltage. This drop is most pronounced for the maximum initial two-dimensional hole concentrations ~ 3 × 10{sup 13} cm{sup –2} (limited from above by the condition for the possibility of their significant reduction without the electrical breakdown of diamond). This is explained by a decrease in the degree of screening of scattering Coulomb potentials of ionized boron atoms and an increase in the scattering efficiency of degenerate holes from these atoms due to a drop in the kinetic energy of holes. The corresponding calculations of the transport scattering cross section of holes are performed beyond the Born approximation (i.e., perturbation theory), which is inapplicable for boron δ-doped diamond layers. The predicted effect can be used to increase the efficiency of source-to-drain current modulation by a gate voltage in diamond field-effect transistors (FETs) with δ-doped conduction channels.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Verilator Testbench Environment (VTE) v0.1

VTE is a library that allows fast and simple generation of C++ testers for modules written in Chisel and build an efficient interface to existing C++ based simulators. It contains Scala-based interface and C++ testbench class. Scala interface interacts with Firtl Interpreter and generates a basic set of C++ testbench files. These files contain the list of the Device Under Test (DUT) input-output ports as well as their parameters. C++ testbench provides functionalities similar to the Chisel PeekPokeTester, such as poke, expect, step functions. As a backend it uses Verilator.

Fatollahi-Fard, Farzad↗

Chapter 22: Compressed Air Evaluation Protocol. The Uniform Methods Project: Methods for Determining Energy Efficiency Savings for Specific Measures

Compressed-air systems are used widely throughout industry for many operations, including pneumatic tools, packaging and automation equipment, conveyors, and other industrial process operations. Compressed-air systems are defined as a group of subsystems composed of air compressors, air treatment equipment, controls, piping, pneumatic tools, pneumatically powered machinery, and process applications using compressed air. A compressed-air system has three primary functional subsystems: supply, distribution, and demand. Air compressors are the primary energy consumers in a compressed-air system and are the primary focus of this protocol. The two compressed-air energy efficiency measures specifically addressed in this protocol are: High-efficiency/variable speed drive (VSD) compressor replacing modulating, load/unload, or constant-speed compressor; and Compressed-air leak survey and repairs. This protocol provides direction on how to reliably verify savings from these two measures using a consistent approach for each.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Status Assessment of the PROTEUS-ORIGEN Coupling

As part of the Nuclear Energy Advanced Modeling and Simulation (NEAMS) Campaign of the U.S. Department of Energy, Office of Nuclear Energy, an initiative was started to provide time dependent isotopic modeling capabilities to the PROTEUS neutronics module of the Simulation based High-efficiency Advanced Reactor Prototyping (SHARP) toolkit. This capability is to be provided through a coupling with the Oak Ridge Isotope Generation (ORIGEN) code, which is part of the SCALE code package developed and maintained at Oak Ridge National Laboratory. This development has been a joint effort between the developers of PROTEUS at Argonne National Laboratory (ANL) and Oak Ridge National Laboratory (ORNL).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Collaborative Research Towards a tonne-scale bolometer-based neutrinoless double beta decay experiment (Final Report)

Cryogenic bolometers are an excellent technology for neutrinoless double beta decay searches owing to their very high energy resolution and potential for high radiopurity. The current most advanced large-scale experiment using these detectors is the Cryogenic Underground Observatory for Rare Events (CUORE). The largest source of background in CUORE is degraded alpha particles, emitted from shallow depths of the detector holders, which can deposit a thermal energy signature similar to neutrinoless double beta decay. To mitigate this background, the CUPID concept (CUORE Upgrade with Particle IDentification) proposes to use scintillating cryogenic detectors. Detecting both the scintillation light and the thermal signal allows discrimination between alpha particle events and beta/gamma events. We report on the design and execution of R&D tests to optimize the design of the single detector module, in particular the scintillation light collection efficiency at cryogenic temperatures.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

X-ray Beam Induced Current Measurements for Multi-Modal X-ray Microscopy of Solar Cells

X-ray beam induced current (XBIC) measurements allow mapping of the nanoscale performance of electronic devices such as solar cells. Ideally, XBIC is employed simultaneously with other techniques within a multi-modal X-ray microscopy approach. An example is given herein combining XBIC with X-ray fluorescence to enable point-by-point correlations of the electrical performance with chemical composition. For the highest signal-to-noise ratio in XBIC measurements, lock-in amplification plays a crucial role. By this approach, the X-ray beam is modulated by an optical chopper upstream of the sample. The modulated X-ray beam induced electrical signal is amplified and demodulated to the chopper frequency using a lock-in amplifier. By optimizing low-pass filter settings, modulation frequency, and amplification amplitudes, noise can efficiently be suppressed for the extraction of a clear XBIC signal. A similar setup can be used to measure the X-ray beam induced voltage (XBIV). Beyond standard XBIC/XBIV measurements, XBIC can be measured with bias light or bias voltage applied such that outdoor working conditions of solar cells can be reproduced during in-situ and operando measurements. Ultimately, the multi-modal and multi-dimensional evaluation of electronic devices at the nanoscale enables new insights into the complex dependencies between composition, structure, and performance, which is an important step towards solving the materials' paradigm.

14 SOLAR ENERGY↗

Cadmium Telluride Solar Cells: From Fundamental Science to Commercial Applications

In order to meet aggressive decarbonization goals, photovoltacs (PV) need to expand substantially. The current technology that heavily dominates the market, silicon (Si), comprises 95% of the world's PV production, is energy intensive to make, and can take up a substantial portion of the remaining carbon budget if expanded. Conversely, cadmium telluride (CdTe) comprises much of the remaining 5% of the global PV market and has a significantly lower carbon footprint than Si, historically costs less to produce, and is critically important to U.S. competitiveness in the global market. Importantly, CdTe still has room to grow, particularly related to efficiency because voltage has historically been much lower than what we calculate it should be. My research is focused in part on understanding this voltage deficit from a fundamental perspective by studying bulk materials and interfaces. One of the most important regions of the device is buried within the stack, so I developed a technique to cleave and reveal buried interfaces. This cleave technique has enabled a much better scientific understanding and allows us to make lightweight, flexible PV while maintaining low costs, high efficiency, and high throughput associated with standard module processing.

CdTe↗

The Evolution of the Internet Community and the"Yet-to-Evolve" Smart Grid Community: Parallels and Lessons-to-be-Learned

The Smart Grid envisions a transformed US power distribution grid that enables communicating devices, under human supervision, to moderate loads and increase overall system stability and security. This vision explicitly promotes increased participation from a community that, in the past, has had little involvement in power grid operations -the consumer. The potential size of this new community and its member's extensive experience with the public Internet prompts an analysis of the evolution and current state of the Internet as a predictor for best practices in the architectural design of certain portions of the Smart Grid network. Although still evolving, the vision of the Smart Grid is that of a community of communicating and cooperating energy related devices that can be directed to route power and modulate loads in pursuit of an integrated, efficient and secure electrical power grid. The remaking of the present power grid into the Smart Grid is considered as fundamentally transformative as previous developments such as modern computing technology and high bandwidth data communications. However, unlike these earlier developments, which relied on the discovery of critical new technologies (e.g. the transistor or optical fiber transmission lines), the technologies required for the Smart Grid currently exist and, in many cases, are already widely deployed. In contrast to other examples of technical transformations, the path (and success) of the Smart Grid will be determined not by its technology, but by its system architecture. Fortunately, we have a recent example of a transformative force of similar scope that shares a fundamental dependence on our existing communications infrastructure - namely, the Internet. We will explore several ways in which the scale of the Internet and expectations of its users have shaped the present Internet environment. As the presence of consumers within the Smart Grid increases, some experiences from the early growth of the Internet are expected to be informative and pertinent.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Dynamic and reversible transformations of subnanometre-sized palladium on ceria for efficient methane removal

Reversibly adjusting the active structures of supported metal catalysts in response to dynamic working conditions has long been pursued. Here we report the reaction-environment-modulated transformations of subnanometre-sized Pd on CeO 2 for efficient methane removal, leveraging the reaction environments at different stages of automotive exhaust aftertreatment. During the cold start of vehicles, inactive Pd 1 single atoms are readily transformed into PdO $x$ subnanometre clusters by CO even at room temperature with excess O 2 , resulting in boosted low-temperature CH 4 oxidation. At elevated temperatures, dispersion of PdO $x$ cluster into Pd 1 against metal sintering renders outstanding hydrothermal stability to the catalyst, to be activated during the next vehicle start. Combined experimental and computational studies elucidate the dynamically evolved Pd speciation on CeO 2 at an atomic level. In conclusion, modulating the reversible nature of supported metals helps overcome the long-existing trade-off between low-temperature activity and high-temperature stability, also providing a new paradigm for designing intelligent catalysts that brings single-atom/cluster catalysts closer to real applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mini-modules made with monolithically integrated all-perovskite tandems

The objective of the project was to improve the efficiency and stability of all-perovskite tandem solar cells. Another goal was to demonstrate that a mini-module could be made using scalable methods. When the project started, there were < 10 papers on narrow band gap solar cells, so we needed to improve the chemical composition, find suitable contacts and do fundamental research to learn more about Sn-containing perovskites. We achieved > 20 % PCE and < 5 % degradation after 1000 hours under one sun illumination. We found that stability is dramatically improved by using < 50 % Sn and avoiding anything that is acidic from interacting with the Sn. For the top cell, we needed to increase the band gap and solve a problem with wrinkling due to compressive stress that arises during spin coating. We achieved > 20 % PCE and < 5 % degradation after 1000 hours under one sun illumination. It is necessary to have a recombination layer between the two solar cells. We developed an ALD process to deposit recombination layers that are excellent barriers. These barriers solved a problem associated with the first solar cell getting partially dissolved when the second solar cell is deposited. This process greatly improved the yield by reducing the density of shunts between the cells. In collaboration with other researchers at NREL, we made 25.5 % efficient tandems that maintain 80 % of their stability after 1500 hours under 0.8 sun illumination. We published manuscripts that compare options for commercializing various kinds of perovskite modules taking into account possible degradation near scribe lines, reverse bias degradation in partially shaded modules, and the ability to bin cells if singulated cells are connected by wire.

14 SOLAR ENERGY↗

A Novel Technique for Pulsed Operation of Magnetrons without Modulation of Cathode Voltage

Modern pulsed superconducting accelerators of megawatt beams require efficient RF sources controllable in phase and power. For each Superconducting RF (SRF) cavity is desirable a separate RF source with power up to hundreds of kW with pulse duration in the millisecond range. The efficiency of the traditional RF sources (klystrons, IOTs, solid-state amplifiers) is lower than that of the magnetrons, while the cost of a unit of RF power is much higher. Therefore the magnetron-based RF sources would significantly reduce the capital and operation costs in comparison with the traditional RF sources. A recently developed an innovative technique makes possible the pulsed generation of magnetrons powered below the self-excitation threshold voltage. This technique does not require pulse modulators to form RF pulses. The magnetron operation in this regime is stable, low noise, controllable in phase and power, and provides higher efficiency than other types of RF power sources. It allows operation in pulsed modes with large duty factor. The developed technique and its experimental verification are considered and discussed.

43 PARTICLE ACCELERATORS↗

LED Chips and Packaging for 120 LPW SSL Component

Cree has developed a new, high-efficiency, low-cost, light emitting diode (LED) lamp module that should be capable of replacing standard, halogen, fluorescent and metal halide lamps based on the total cost of ownership. White LEDs are produced by combining one or more saturated color LEDs with a phosphor or other light down-converting media to achieve white broad-band illumination. This two year project addressed LED chip and package efficiency improvements to establish a technology platform suitable for low-cost, high-efficiency commercial luminaires. Novel photonic-crystal LEDs were developed to improve the light extraction efficiency of blue GaN-based LEDs compared to the baseline technology. Improved packaging designs that reduced down-conversion and absorption related light losses, led to a higher overall LED efficiency. Specifically, blue LEDs were demonstrated with light output nearing 600 mW and an external quantum efficiency greater than 60 percent (using 1 mm2 chips at an operating current of 350 mA). The results were achieved using a novel, production capable photonic-crystal LED fabrication process. These LEDs formed the basis for a multi-chip white lamp module prototype, which provided 510 lumens light output at a correlated color temperature (CCT) of 3875 K and an operating current of 350 mA per 1mm 2 chip. The overall conversion efficiency at 4100 K improved to ~ 65%. The resulting efficacy is 112 lumens per watt (LPW) a 33% improvement over the start of the project. In addition, a proof-of-concept luminaire was demonstrated that provided a flux of 1700 lumens at a 3842 K CCT.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

100 Gbps multiplexed inter-satellite optical wireless communication system

In this paper, the performance analysis of the inter-satellite optical wireless communication system (IsOWC) is carried out in presence of optical space channel. Here the proposed model is a 16×100 Gbps dense multiplexed IsOWC. The dual polarized quadrature phase shift keying (DP-QPSK) modulation is used for improving the optical signal to noise ratio tolerance of the system. Further, the spectral efficiency and the receiver sensitivity is improved by incorporating the coherent orthogonal frequency division multiplexing (CO-OFDM) technique in the proposed IsOWC system. The performance of the system is evaluated by bit error rate (BER), error vector magnitude percentage, received signal power, constellation diagram. A comparative study has been carried out between different modulation techniques such as quadrature phase shift keying and DP-QPSK used in IsOWC system. It is observed that, an inter-satellite distance of 15,600 km is obtained with the proposed model at 100 Gbps for a targeted forward error correction log of BER value of − 2.42 or BER of 3.8×10{sup −3}. The maximum possible data rate for different inter and intra orbit satellite has been calculated. Also, the maximum possible transceiver distance has been calculated for different data rates. The integration of two advanced technologies such as DP-QPSK modulation with CO-OFDM technique in the proposed model may impel the market demands for high bandwidth intensive and high data rate applications.

42 ENGINEERING↗

Performance Modelling and Yearlong Outdoor Degradation Analysis of a GaAs//Si Tandem Module

Silicon-based tandem photovoltaic cells and modules are forecasted to enter mass production around the year 2026. Previous research efforts on tandem photovoltaic technology have focused heavily on increasing cell efficiencies. However, for successful large-scale deployment of tandem modules, reliability and long-term durability will be equally important. Outdoor performance data beyond the one-year mark enable sophisticated degradation analysis and help build confidence in the reliability and durability of this new technology.

degradation rate↗

Dose optimization with first-order total-variation minimization for dense angularly sampled and sparse intensity modulated radiation therapy (DASSIM-RT)

Purpose: A new treatment scheme coined as dense angularly sampled and sparse intensity modulated radiation therapy (DASSIM-RT) has recently been proposed to bridge the gap between IMRT and VMAT. By increasing the angular sampling of radiation beams while eliminating dispensable segments of the incident fields, DASSIM-RT is capable of providing improved conformity in dose distributions while maintaining high delivery efficiency. The fact that DASSIM-RT utilizes a large number of incident beams represents a major computational challenge for the clinical applications of this powerful treatment scheme. The purpose of this work is to provide a practical solution to the DASSIM-RT inverse planning problem. Methods: The inverse planning problem is formulated as a fluence-map optimization problem with total-variation (TV) minimization. A newly released L1-solver, template for first-order conic solver (TFOCS), was adopted in this work. TFOCS achieves faster convergence with less memory usage as compared with conventional quadratic programming (QP) for the TV form through the effective use of conic forms, dual-variable updates, and optimal first-order approaches. As such, it is tailored to specifically address the computational challenges of large-scale optimization in DASSIM-RT inverse planning. Two clinical cases (a prostate and a head and neck case) are used to evaluate the effectiveness and efficiency of the proposed planning technique. DASSIM-RT plans with 15 and 30 beams are compared with conventional IMRT plans with 7 beams in terms of plan quality and delivery efficiency, which are quantified by conformation number (CN), the total number of segments and modulation index, respectively. For optimization efficiency, the QP-based approach was compared with the proposed algorithm for the DASSIM-RT plans with 15 beams for both cases. Results: Plan quality improves with an increasing number of incident beams, while the total number of segments is maintained to be about the same in both cases. For the prostate patient, the conformation number to the target was 0.7509, 0.7565, and 0.7611 with 80 segments for IMRT with 7 beams, and DASSIM-RT with 15 and 30 beams, respectively. For the head and neck (HN) patient with a complicated target shape, conformation numbers of the three treatment plans were 0.7554, 0.7758, and 0.7819 with 75 segments for all beam configurations. With respect to the dose sparing to the critical structures, the organs such as the femoral heads in the prostate case and the brainstem and spinal cord in the HN case were better protected with DASSIM-RT. For both cases, the delivery efficiency has been greatly improved as the beam angular sampling increases with the similar or better conformal dose distribution. Compared with conventional quadratic programming approaches, first-order TFOCS-based optimization achieves far faster convergence and smaller memory requirements in DASSIM-RT. Conclusions: The new optimization algorithm TFOCS provides a practical and timely solution to the DASSIM-RT or other inverse planning problem requiring large memory space. The new treatment scheme is shown to outperform conventional IMRT in terms of dose conformity to both the targetand the critical structures, while maintaining high delivery efficiency.

61 RADIATION PROTECTION AND DOSIMETRY↗

Module of Laser-Radiation (λ = 1064 nm) Photovoltaic Converters

The results of a study and the development of a module designed for energy transmission via atmospheric channels are presented. The four-cell module based on single-junction metamorphic InGaAs/GaAs converters grown by metal-organic vapor-phase epitaxy has an open-circuit voltage of ~3 V. It is shown that the monochromatic efficiency (at a wavelength of 1064 nm) of this module is 31.5% under exposure to a Xe-lamp with a radiation power of 1.5 W/cm{sup 2}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗