Search NASA⌕ Search

SEARCH · Search NASA

Results for “module performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Macroscopic Nonuniformities in Metal Grids Formed by Cracked Film Lithography Result in 19.3% Efficient Solar Cells

Cracked film lithography (CFL) is an emerging method for patterning transparent conductive metal grids. CFL can be vacuum- and Ag-free, and it forms more durable grids than nanowire approaches. In spite of CFL’s promising transmittance/grid sheet resistance/wire spacing tradeoffs, previous solar cell demonstrations have had relatively low performance. This work introduced macroscopic nonuniformities in the grids to improve the short-circuit current density/fill factor tradeoff in small area Cu(In,Ga)Se2 cells. Furthermore, the performance of optimized baseline grids was matched by CFL grids with microscopic openings and macroscopic patterns, culminating in a 19.3%-efficient cell. Simulations show that uniform CFL grids are enhanced by patterning because it leads to better balance among shadowing, grid resistance and transparent conductive oxide resistance losses. Thin-film module efficiency calculations were performed to highlight the performance gains that metal grids can enable by eliminating the transparent conductive oxide losses and widening monoliths. Adding the patterned CFL grids demonstrated in this work to CIGS modules is predicted to reach 0.7% higher efficiency (absolute) than screen-printed grids.

14 SOLAR ENERGY↗
DOE OSTI2019

Albedo Data to Facilitate Bifacial PV System Planning

For mono-facial photovoltaic (PV) systems, the ground-reflected radiation typically comprises only 1% to 2% of the total radiation received by the PV module. Consequently, a rudimentary understanding of the ground albedo is adequate for predicting their performance. However, for bifacial PV modules where their benefit is determined by the additional radiation reflected by the ground to their backside, a better understanding of albedo values and characteristics is needed by both the PV and financial communities to better estimate performance and to reduce risk. This was identified as a key need at the 2018 Bifacial PV Workshop. Subsequently, the Department of Energy (DOE) has initiated work with the National Renewable Energy Laboratory (NREL) to provide albedo data for different locations and ground surfaces for both the simulation of bifacial PV systems and for summary information, including variations in albedo with respect to time of day, season, and year. This albedo data base will include data from measurement networks (SURFRAD and Ameriflux), and the PV industry is also asked to provide their albedo measurements and take part in a cooperative effort to provide an expansive and accurate data base of albedo values.

14 SOLAR ENERGY↗
DOE OSTI2020

Comparison and Discussion on Shortcircuit Protections for Silicon-Carbide MOSFET Modules: Desaturation Versus Rogowski Switch-Current Sensor

Survivability of silicon-carbide (SiC) mosfet modules during short circuit (SC) is essential for modern power electronics systems due to large economic implications. SiC mosfet modules exhibit narrow SC withstand times and generally much lower SC robustness than silicon (Si) insulated-gate bipolar transistors (IGBTs). This puts a critical concern on their utilization, further stressing the importance of reliable protection. This article presents a comprehensive analysis and discussion on the SiC mosfet module SC protection and performance comparison between conventional desaturation detection, previously used for Si IGBT protection, and Rogowski switch-current sensor (RSCS) detection. In addition, this article presents the experimental design for soft turn-off as a reaction to the SC detection to avoid excessive overshoots during the abrupt turn-off of the SC current. To perform different types of SC with various fault inductances on different temperatures, and for the sake of fair comparison under the same conditions, a gate-driver unit for 1.2 kV SiC mosfet half-bridge modules is developed containing both detection methods. The results demonstrate that both methods are successful in protecting the module in all SC types, with superiority of the RSCS detection and concerns for desaturation detection in high-inductance and high dc-bus voltage SC events.

42 ENGINEERING↗
DOE OSTI2026

Semi-Transparent Perovskite Solar Cells in a Stacked Tandem Module: Cooperative Research and Development Final Report, CRADA Number CRD-19-00810

This project seeks to develop device design, materials composition, and processing tools and parameters to fabricate semi-transparent perovskite solar cells and modules for application in stand-alone products or added to other solar cells in a mechanically stacked tandem configuration. This technology presents significant advanced manufacturing challenges and opportunities in getting to scale, including development of perovskite inks, scalable perovskite and heterojunction deposition and annealing processes, heterojunction composition, transparent electrode composition and deposition process, anti-reflection layer composition and deposition process, and cell to module integration processes. Modification 5: The proposed project seeks to develop device design, materials composition, and processing tools and parameters to fabricate semi-transparent perovskite solar cells and modules for application in stand-alone products or added to other solar cells in a mechanically-stacked tandem configuration. This technology presents significant advanced manufacturing challenges and opportunities in getting to scale, including development of perovskite inks, scalable perovskite and heterojunction deposition and annealing processes, heterojunction composition, transparent electrode composition and deposition process, passivation layers including in module scribes, anti-reflection layer composition and deposition process, and cell to module integration processes. Advanced metrology and characterization will be performed on perovskite films, cells and module. Furthermore, we will examine module or materials recycling for circular economy considerations. Modifcation 6: Gigahertz frequency microwave pump-probe spectroscopies are highly sensitive to thin film semiconductor photoconductivity of individual and stacks of layers that comprise perovskite solar cells. As such, these techniques will be used to qualify reproducibility and quality correlations during the manufacturing process. Modification 7: Mechanical adhesion of top contacts within perovskite modules significantly impacts the durability of the module when exposed to accelerated degradation testing. The adhesion between the perovskite/transport layer interface and the transport layer/top contact interface are both very sensitive small changes in processing. ALD processing conditions of the transport layer will be tuned to optimize the mechanical adhesion within the perovskite module stack.

14 SOLAR ENERGY↗
NASA NTRS1973

On the minimization of the prime power consumption of a coupling-modulated gas laser transmitter

The prime power requirements of a coupling-modulated gas laser transmitter are presented. The latter consists of a gas discharge tube and electro-optic modulator inside a laser resonator. In performing the calculations, the laser discharge length and the modulator voltage are simultaneously varied so that the transmitted power remains constant. In this way, tradeoffs can be made between the prime power supplied individually to the discharge tube and to the modulator driver to obtain a transmitter configuration which minimizes the total prime power consumption. An analytical expression is derived which describes the effects of information bandwidth and transmitter output power on the prime power requirements. Specific numerical results are obtained for a CO2 laser transmitter based on presently available experimental data.

Degnan, J. J.↗
NASA NTRS1973

Heterodyne readout for read-write holographic memories

A heterodyne readout technique for read-write holographic memory systems that reconstruct a virtual image wavefront is described and demonstrated. The conventionally recorded hologram is illuminated simultaneously with a suitable combination of temporally modulated reference and modified object waves for readout. Best performance is obtained for temporal phase modulation. The coupling of the illuminating wavefronts by the hologram is analyzed.

Mezrich, R. S.↗
NASA NTRS1974

Minimization of the prime power consumption of a coupling-modulated gas laser transmitter

The present article addresses itself to the prime power requirements of a coupling-modulated gas laser transmitter. The latter consists of a gas discharge tube and electrooptic modulator inside a laser resonator. In performing the calculations, the laser discharge length and the modulator voltage are simultaneously varied so that the transmitted power remains constant. In this way, tradeoffs can be made between the prime power supplied individually to the discharge tube and to the modulator driver to obtain a transmitter configuration that minimizes the total prime power consumption. An analytical expression is derived that describes the effects of information bandwidth and transmitter output power on the prime power requirements. Specific numerical results are obtained for a CO2 laser transmitter based on presently available experimental data.

Degnan, J. J.↗
NASA NTRS1984

Parabolic Dish Stirling Module

The design, manufacture, and assembly of a commercially designed parabolic dish Stirling 25 kWe module is examined. The cost, expected performance, design uniquenesses, and future commercial potential of this module, which is regarded as the most technically advanced in the parabolic dish industry is discussed.

Washom, B.↗
NASA NTRS1987

Performance improvements in silicon flat-plate cells and modules

This paper reports the development of a flat-plate module based on highly efficient ion-implanted silicon solar cells. The cells developed in this work are 53 sq cm in area and have exhibited AM 1.5 efficiencies of over 18 percent. The use of back surface reflectors to reduce module operating temperature is discussed. A comparison of various approaches to cell design is made, and module test data for these designs are presented. A comparison of float zone and Czochralski silicon is made. Module efficiency of over 15 percent (at 25 C) is reported.

Spitzer, M. B.↗
NASA NTRS1988

Maintenance and supply options

The object of the Maintenance and Supply Option was to develop a high level operational philosophy related to maintenance and supply operations and incorporate these concepts into the Lunar Base Study. Specific products to be generated during this task were three trade studies and a conceptual design of the Logistic Supply Module. The crew size study was performed to evaluate crew sizes from the baseline size of four to a crew size of eight and determine the preferred crew size. The second trade study was to determine the impact of extending surface stay times and recommend a preferred duration of stay time as a function of crew, consumables, and equipment support capabilities. The third trade study was an evaluation of packaging and storage methods to determine the preferred logistics approach to support the lunar base. A modified scenario was developed and served as the basis of the individual trade studies. Assumptions and guidelines were also developed from experience with Apollo programs, Space Shuttle operations, and Space Station studies. With this information, the trade studies were performed and a conceptual design for the Logistic Supply Module was developed.

Source record↗
NASA NTRS1997

Electrical and Optical Performance Characteristics of 0.74-eV p/n InGaAs Monolithic Interconnected Modules

There has been a traditional trade-off in thermophotovoltaic (TPV) energy conversion development between system efficiency and power density. This trade-off originates from the use of front surface spectral controls such as selective emitters and various types of filters. A monolithic interconnected module (MIM) structure has been developed which allows for both high power densities and high system efficiencies. The MIM device consists of many individual indium gallium arsenide (InGaAs) cells series-connected on a single semi-insulating indium phosphide (InP) substrate. The MIM is exposed to the entire emitter output, thereby maximizing output power density. An infrared (IR) reflector placed on the rear surface of the substrate returns the unused portion of the emitter output spectrum back to the emitter for recycling, thereby providing for high system efficiencies. Initial MIM development has focused on a 1 sq cm device consisting of eight (8) series interconnected cells. MIM devices, produced from 0.74-eV InGaAs, have demonstrated V(sub oc) = 3.2 volts, J(sub sc) = 70 mA/sq cm, and a fill factor of 66% under flashlamp testing. Infrared (IR) reflectance measurements (greater than 2 micron) of these devices indicate a reflectivity of greater than 82%. MIM devices produced from 0.55-eV InGaAs have also been demonstrated. In addition, conventional p/n InGaAs devices with record efficiencies (11.7% AM0) have been demonstrated.

Wilt, David M.↗
NASA NTRS1981

Advanced space system analysis software. Technical, user, and programmer guide

The LASS computer program provides a tool for interactive preliminary and conceptual design of LSS. Eight program modules were developed, including four automated model geometry generators, an associated mass properties module, an appendage synthesizer module, an rf analysis module, and an orbital transfer analysis module. The existing rigid body controls analysis module was modified to permit analysis of effects of solar pressure on orbital performance. A description of each module, user instructions, and programmer information are included.

Farrell, C. E.↗
NASA NTRS1991

Generic hypersonic inlet module analysis

A computational study associated with an internal inlet drag analysis was performed for a generic hypersonic inlet module. The purpose of this study was to determine the feasibility of computing the internal drag force for a generic scramjet engine module using computational methods. The computational study consisted of obtaining two-dimensional (2D) and three-dimensional (3D) computational fluid dynamics (CFD) solutions using the Euler and parabolized Navier-Stokes (PNS) equations. The solution accuracy was assessed by comparisons with experimenal pitot pressure data. The CFD analysis indicates that the 3D PNS solutions show the best agreement with experimental pitot pressure data. The internal inlet drag analysis consisted of obtaining drag force predictions based on experimental data and 3D CFD solutions. A comparative assessment of each of the drag prediction methods is made and the sensitivity of CFD drag values to computational procedures is documented. The analysis indicates that the CFD drag predictions are highly sensitive to the computational procedure used.

Cockrell, Charles E., Jr.↗
NASA NTRS2004

Generic Hypersonic Inlet Module Analysis

A computational study associated with an internal inlet drag analysis was performed for a generic hypersonic inlet module. The purpose of this study was to determine the feasibility of computing the internal drag force for a generic scramjet engine module using computational methods. The computational study consisted of obtaining two-dimensional (2D) and three-dimensional (3D) computational fluid dynamics (CFD) solutions using the Euler and parabolized Navier-Stokes (PNS) equations. The solution accuracy was assessed by comparisons with experimental pitot pressure data. The CFD analysis indicates that the 3D PNS solutions show the best agreement with experimental pitot pressure data. The internal inlet drag analysis consisted of obtaining drag force predictions based on experimental data and 3D CFD solutions. A comparative assessment of each of the drag prediction methods is made and the sensitivity of CFD drag values to computational procedures is documented. The analysis indicates that the CFD drag predictions are highly sensitive to the computational procedure used.

Cockrell, Chares E., Jr.↗