Search NASA⌕ Search

SEARCH · Search NASA

Results for “scanning electron diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Incident flux angle induced crystal texture transformation in nanostructured molybdenum films

Molybdenum films were observed to undergo a dramatic change in crystal texture orientation when the incident flux angle was varied in an oblique angle sputter deposition on amorphous substrates. Reflection high-energy electron diffraction pole figure and scanning electron microscopy were used to analyze in detail the texture orientation of the films. The normal incident deposition resulted in a fiber texture film with the minimum energy (110) crystal plane parallel to the substrate surface. A (110)[110] biaxial texture was observed for the samples grown with low incident angles of less than 45 Degree-Sign , with respect to the surface normal. On the other hand, for an oblique angle deposition of larger than 60 Degree-Sign , a (111)[112] biaxial texture was observed and appeared to be consistent with a zone T structure where the geometrically fastest growth [001] direction of a crystal plays a dominant role in defining the texture. We argue that a structural transition had occurred when the incident flux was varied from near normal incidence to a large angle.

36 MATERIALS SCIENCE↗

Electrochemical properties of Li[Li{sub 0.2}Mn{sub 0.54}Co{sub 0.13}Ni{sub 0.13}]O{sub 2} cathode thin film by RF sputtering for all-solid-state lithium battery

The Li[Li{sub 0.2}Mn{sub 0.56}Ni{sub 0.13}Co{sub 0.13}]O{sub 2} thin films were prepared by radio frequency magnetron sputtering on Pt/Ti/SiO{sub 2}/Si substrate with target contained a 5% excess of lithium precursor. Thin films were deposited under various deposition conditions such as working pressure, gas ratio of Ar and O{sub 2}, and the temperature of in-situ annealing treatment. The thin films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The electrochemical property was estimated by a WBC3000 cycler with Li|Li[Li{sub 0.2}Mn{sub 0.54}Ni{sub 0.13}Co{sub 0.13}]O{sub 2} half-type cell at 1C charge/discharge rate. The (0 0 3) and (1 0 4) diffraction peaks which represent layered {alpha}-NaFeO{sub 2} type structure (space group R-3m) were observed. Optimal magnetron sputtering conditions were detected. The 500 Degree-Sign C annealed thin film after deposited at 10 m Torr in Ar:O{sub 2}=3:1 shows a high discharge capacity of around 62 {mu}Ah/cm{sup 2} {mu}m with a high cyclic retention. - Graphical abstract: The Li[Li{sub 0.2}Mn{sub 0.56}Ni{sub 0.13}Co{sub 0.13}]O{sub 2} films is suitable for Lithium thin film battery. The film exhibits great discharge capacity (62 {mu}Ah/cm{sup 2} {mu}m) up to 200 cycles. Highlights: Black-Right-Pointing-Pointer High capacity thin films were deposited by RF magnetron sputtering. Black-Right-Pointing-Pointer Sputtering conditions were optimized by structural and electrochemical analysis. Black-Right-Pointing-Pointer Li[Li{sub 0.2}Mn{sub 0.56}Ni{sub 0.13}Co{sub 0.13}]O{sub 2} thin film shows a high capacity, 62 {mu}Ah/cm{sup 2} {mu}m. Black-Right-Pointing-Pointer The thin film shows an excellent cycling stability up to 200 cycles.

36 MATERIALS SCIENCE↗

Interfacial characterization of alumina-to-alumina joints fabricated using silver–copper–titanium interlayers

Two Ag–Cu–Ti interlayers with different compositions (Ag–35.3Cu–1.75Ti and Ag–26.7Cu–4.5Ti) were used to join sintered polycrystalline Al{sub 2}O{sub 3} having different amounts of porosity to investigate the effect of titanium and porosity contents on evolution of interfacial chemistry and microstructures. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy dispersive spectroscopy (EDS) were used to characterize the interfacial microstructure. Two reaction layers, Ti{sub 2}O and Cu{sub 3}Ti{sub 3}O, were found at the interface of Ag–Cu–Ti interlayers and Al{sub 2}O{sub 3} using a series of simulated and experimental selected area diffraction patterns (SADP) of TEM and EDS. The total thickness of Ti{sub 2}O and Cu{sub 3}Ti{sub 3}O reaction layers at the interfaces increases with increasing amounts of Ti in the Ag–Cu–Ti interlayers but is independent of the porosity content in the Al{sub 2}O{sub 3}. Two possible formation mechanisms of Ti{sub 2}O and Cu{sub 3}Ti{sub 3}O reaction layers at the interface of Ag–Cu–Ti interlayers and Al{sub 2}O{sub 3} have been proposed based on the interfacial characterization performed in the present study. - Highlights: • Effect of alumina porosity and % Ti in interlayer on interface structure delineated • SEM, EDS, XRD, TEM with SADP used to delineate phases, compositions, crystallography • Ti{sub 2}O and Cu{sub 3}Ti{sub 3}O reaction layers identified and their formation mechanisms proposed.

36 MATERIALS SCIENCE↗

AC Susceptibility and Superconducting Properties of Graphene Added YBa{sub 2}Cu{sub 3}O{sub 7−d}

The effect of graphene (G) addition on YBa{sub 2}Cu{sub 3}O{sub 7−δ}(G){sub x} (x = 0 − 0.03 wt%) has been studied using the X-ray diffraction method, scanning electron microscopy, electrical resistance versus temperature, transport critical current density J{sub c}, and AC susceptibility measurements. XRD patterns showed single-phase YBa{sub 2}Cu{sub 3}O{sub 7−δ} (YBCO) for all samples. SEM micrographs showed filling of the voids between YBa{sub 2}Cu{sub 3}O{sub 7−δ} grains as graphene was added. The temperature-dependent electrical resistance curves showed metallic normal state behavior and onset transition temperature T{sub conset} between 90 and 92 K for all samples. AC susceptibility measurement showed transition temperature T{sub cχ{sup ′}} between 90 and 93 K. T{sub cχ{sup ′}} was maintained or improved slightly as graphene was added. The x = 0.001 wt% showed the highest J{sub c}, i.e., 2750 A cm{sup −2} at 77 K and 5570 mA cm{sup −2} at 30 K which was 13 and 40 times higher than that of the non-added YBCO, respectively. The peak temperature T{sub p} of the imaginary part of the susceptibility χ{sup ″} was around 78–82 K for all samples indicating grain coupling was not weakened as graphene was added.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Magnetic Performance and Evaluation of Radiofrequency Hyperthermia of Perovskite La{sub 1−x}Sr{sub x}MnO{sub 3}

Magnetic nanoparticles (MNPs) can induce localized hyperthermia by alternating magnetic fields, in order to kill cells at tumor sites. In this study, La{sub 1−x}Sr{sub x}MnO{sub 3} nanoparticles with x = 0.2, 0.3, 0.4, and 0.5 were prepared via sol–gel technique. The synthesized nanoparticles were characterized in terms of structure, morphology, and magnetic properties with Fourier transform infrared (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and vibrating sample magnetometer (VSM) studies. The average size of nanoparticles was measured to be 57.09, 30.477, 10.24, and 35.982 nm by Williamson–Hall method for x = 0.2, 0.3, 0.4, and 0.5, respectively. The absence of hysteresis in the magnetic response of nanoparticles represents the superparamagnetic behavior. Toxicity test was also performed to evaluate the toxicity concerns of the prepared nanoparticles upon entrance to the body. Furthermore, the alternating current magnetic heating characteristics of La{sub 1−x}Sr{sub x}MnO{sub 3} nanoparticles was also studied, by 1 mg/mL concentration, to test the ability of the nanoparticles as magnetic hyperthermia treatment agents. The magnetothermia were measured in an RF magnetic field of 88 Oe and 430 kHz. The present work reveals that LSMO nanoparticles possess the biocompatible properties for biomedical applications and can provide the required heat at appropriate time.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of SiO{sub 2} on the Formation of Acicular Calcium Ferrite in Sinter

SiO{sub 2} greatly influences the formation of acicular calcium ferrite (ACF), which is the main binder phase in sinter, but the mechanism of its influence is not yet clear. Experiments were carried out under air at 1200 °C with different amounts of SiO{sub 2} mixed with Fe{sub 2}O{sub 3} and Ca(OH){sub 2}. X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and three-dimensional (3D) reconstruction were used to characterize the phase and morphological changes of the sintered samples. The results show that SiO{sub 2} can form silicon-ferrite of calcium (SFC), which is beneficial to the formation of ACF in sinter. The SFC content first increased and then decreased with the increasing SiO{sub 2} content. The sintered sample contained the highest contents of SFC and ACF when w(SiO{sub 2}) was 3 to 4 pct. The morphological changes in calcium ferrite observed with the increasing SiO{sub 2} content followed a sequence of massive → platy → acicular; both platy calcium ferrite and ACF were the longest in one direction in their 3D morphology. The inclusion of Si{sup 4+} in calcium ferrite crystals changes the crystal growth habit from having no obvious orientation to having a preferential orientation along the (040) or (320) surfaces, as determined by the first-principles calculations and XRD analysis of block samples. Viscosity was the main environmental factor influencing the size of ACF in samples with sufficient liquid phase.

36 MATERIALS SCIENCE↗

Effects of europium substitution for In on structure and photoelectric properties of CuIn{sub 1−x}Eu{sub x}Te{sub 2}

The structures and optical and electric properties of europium doped CuIn{sub 1−x}Eu{sub x}Te{sub 2} have been studied systematically using powder X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive spectrum (EDS), ultraviolet and visible spectrophotometer (UV–vis), and standard four-probe method. The studies reveal that the minor europium doping into CuIn{sub 1−x}Eu{sub x}Te{sub 2} could still stabilize the chalcopyrite structure in a solid solution of x=0.1. The lattice parameters are going up with increasing the content of europium in CuIn{sub 1−x}Eu{sub x}Te{sub 2} due to the size effect at In site. The structural refinement confirms that Eu partly substitutes for In and occupies the 4b crystal position. SEM morphologies show that the europium doping into CuIn{sub 1−x}Eu{sub x}Te{sub 2} can fine the grains from the largely agglomerated state to the uniformly separated state. The electrical resistivities of single phase CuIn{sub 1−x}Eu{sub x}Te{sub 2} follow a mixture model of hopping conductivity and variable range hopping conductivity. The absorption band-gaps of CuIn{sub 1−x}Eu{sub x}Te{sub 2} at room temperature tend to increase with increasing Eu content. CuIn{sub 1−x}Eu{sub x}Te{sub 2} might be a good candidate for photovoltaic cell. - Graphical abstract: CuIn{sub 0.9}Eu{sub 0.1}Te{sub 2} follows a mixture of hopping conductivity and variable range hopping conductivity mechanism. - Highlights: • Novel europium doped CuIn{sub 1−x}Eu{sub x}Te{sub 2}. • Potential application for devices and solar cells. • A mixture of hopping and variable range hopping conductivity mechanism.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Corrosion resistance of ZrO{sub 2}–TiO{sub 2} nanocomposite multilayer thin films coated on carbon steel in hydrochloric acid solution

This work reports the achievement of preparing of x% zirconia (ZrO{sub 2})–titania (TiO{sub 2}) composite coatings with different ZrO{sub 2} percent on the carbon steel by dipping substrates in sol–gel solutions. The prepared coated samples were investigated by various surface techniques including X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDAX). Open-circuit potential (OCP), potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) methods were employed to investigate the corrosion resistance of the coated carbon steel substrates in 1.0 M HCl solution at 50 °C. The data showed that, the corrosion protection property is not always proportional to the percent of ZrO{sub 2}. It can be inferred that there is an optimum percent (10%ZrO{sub 2}) for beneficial effects of loading ZrO{sub 2} on the protection efficiency (98.70%), while higher loading percent of ZrO{sub 2} in the sol–gel coating leads to the formation of a fragile film with poor barrier properties. EDAX/SEM suggests that the metal surface was protected through coating with ZrO{sub 2}–TiO{sub 2} composite films. - Highlights: • Sol–gel TiO{sub 2} doped with ZrO{sub 2} films deposited on carbon steel substrate • XRD measurements of x wt.% ZrO{sub 2}–TiO{sub 2} showed the (101) peaks broader than that of TiO{sub 2}. • SEM results proved that, the cracking decreases with the number of layers. • The prepared films can improve the corrosion resistance of the carbon steel substrate. • 10%ZrO{sub 2} loading is the optimal percent for useful effects on the corrosion resistance.

36 MATERIALS SCIENCE↗

Facile synthesis of Cu/Cu{sub x}O nanoarchitectures with adjustable phase composition for effective NO{sub x} gas sensor at room temperature

Graphical abstract: The Cu/Cu{sub x}O nanoarchitectures with 30–70 nm hollow nanospheres reduced by 3 mmol NaBH{sub 4} exhibits excellent gas-sensing property to low-concentration NO{sub x} gas at room temperature. - Highlights: • The Cu/Cu{sub x}O nanoarchitectures with hollow nanospheres are successfully synthesized. • The method is used for preparing the with Cu/Cu{sub x}O adjustable phase composition. • The C3 sample exhibites excellent gas-sensing propertie to NO{sub x} at room temperation. • The Cu/Cu{sub x}O nanoarchitectures have significant for application of gas sensor. - Abstract: The Cu/Cu{sub x}O nanoarchitectures with 30–70 nm hollow nanospheres are successfully synthesized by a facile wet chemical method. The synthesized products have been studied by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and thermo gravimetric-differential scanning calorimetry (TG-DSC) analysis. The Cu/Cu{sub x}O sensors based on the nanoarchitectures are used to detect the NO{sub x} at room temperature. The results demonstrate that the obtained Cu/Cu{sub x}O nanoarchitectures reduced by 3 mmol NaBH{sub 4} exhibits excellent gas-sensing properties: low detection limit of 0.97 ppm, relatively high sensitivity, short response time, broad linear range and high selectivity. The reasons for gas-sensing activity enhancement on Cu/Cu{sub x}O nanoarchitectures are discussed. The Cu/Cu{sub x}O nanocrystalline with the hierarchical pores structure and tunable compositions have significant for application of gas sensor.

36 MATERIALS SCIENCE↗

Vanadium oxides nanostructures: Hydrothermal synthesis and electrochemical properties

Highlights: • Vanadium oxides nanostructures were synthesized hydrothermally. • Reversible redox behavior with doping/dedoping process. • Doping/dedoping is easier for Li{sup +} to Na{sup +}. • Energy-related applications such as cathodes in lithium batteries. - Abstract: A facile and template-free one-pot strategy is applied to synthesize nanostructured vanadium oxide particles via a hydrothermal methodology. X-ray diffraction (XRD), scanning electron microscope (SEM), Fourier transforms infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) have been used to characterize the structure and morphology of the samples. The products are gradually changed from sheet-shaped VO{sub 2}(B) to rod-like V{sub 3}O{sub 7}·H{sub 2}O with decreasing cyclohexanediol as both protective and reducing agent. The specific surface area of the VO{sub 2}(B) nanosheets and V{sub 3}O{sub 7}·H{sub 2}O nanorods was found to be 22 and 16 m{sup 2} g{sup −1}, respectively. Thin films of VO{sub 2}(B) and V{sub 3}O{sub 7}·H{sub 2}O deposited on ITO substrates were electrochemically characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The voltammograms show reversible redox behavior with doping/dedoping process corresponding to reversible cation intercalation/de-intercalation into the crystal lattice of the nanorods/nanosheets. This process is easier for the small Li{sup +} cation than larger ones Na{sup +}.

36 MATERIALS SCIENCE↗

Microwave heating synthesis and formation mechanism of chalcopyrite structured CuInS{sub 2} nanorods in deep eutectic solvent

Graphical abstract: Chalcopyrite structured CuInS{sub 2} nanorods were synthesized by an environmentally friendly microwave heating method in deep eutectic solvent. Results show that microwave heating time plays an important role in the formation of CuInS{sub 2} nanostructure phase. The SEM results indicated that the obtained CuInS{sub 2} nanostructures display rod-like morphology with diameters of about 40 nm and lengths of about 400 nm. The UV–vis spectrum results indicated that the CuInS{sub 2} nanorods exhibit strong absorption from the entire visible light region to the near-infrared region beyond 1100 nm. The possible growth mechanism of CuInS{sub 2} nanorods was discussed. - Abstract: Chalcopyrite structured CuInS{sub 2} nanorods were synthesized by an environmentally friendly microwave heating method in deep eutectic solvent. The as-synthesized CuInS{sub 2} nanorods were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The results indicated that the obtained CuInS{sub 2} nanostructures display rod-like morphology with diameters of about 40 nm and lengths of about 400 nm. The influences of microwave heating time on the formation of CuInS{sub 2} phase were discussed. Ultraviolet–visible (UV–vis) and photoluminescence (PL) spectra were utilized to investigate the optical properties of CuInS{sub 2} nanorods. The results showed that the as-synthesized CuInS{sub 2} nanorods exhibit strong absorption from the entire visible light region to the near-infrared region beyond 1100 nm. PL spectrum of the as-synthesized CuInS{sub 2} nanorods displays an emission peak centered at 580 nm under excitation wavelength of 366 nm at room temperature. The possible growth mechanism of CuInS{sub 2} nanorods was discussed.

36 MATERIALS SCIENCE↗

Characterisation of organic-inorganic hybrid materials of the types ZnxCd1-xSe(1,3-diaminopropane)1/2 and ZnSySe1-y(1,3-diaminopropane)1/2

Highlights: • New hybrid materials: Zn{sub x}Cd{sub 1-x}Se(1,3-DAP){sub 1/2} and ZnS{sub x}Se{sub 1-x}(1,3-DAP){sub 1/2} were obtained. • Hybrids were studied using XRD, TG/DSC, XRD vs. temperature, SEM, UV–vis spectroscopy. • The impact of the composition of the layers on optical properties were studied. - Abstract: Organic-inorganic hybrid materials of the type MeQ(diamine){sub 1/2} (where Me–Zn, Cd, Mn and Q–S, Se, Te) belong to the class of 3D nanomaterials. They are built of layers of II–VI semiconductors and amines, which act as linkers. The main goal of our work was the synthesis of compounds of the type Zn{sub x}Cd{sub 1-x}Se(1,3-diaminopropane){sub 1/2} and ZnS{sub y}Se{sub 1-y}(1,3-diaminopropane){sub 1/2} (where x, y = 0, 0.25, 0.5, 0.75, 1) and the study of properties changed by the composition of the semiconducting layers. Analysis of these materials was carried out with the use of X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), simultaneous thermogravimetry and differential scanning calorimetry (TG-DSC) as well as temperature dependent XRPD enabled us to obtain information about the thermal stability of hybrid compounds with mixed semiconducting layers. Another important part of our work was a study, performed with the use of UV–vis spectroscopy, of the optical properties of these materials.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Influence of processing conditions on the thermoelectric properties of La{sub 1-x}Sr{sub x}CoO{sub 3} (x=0, 0.05)

La{sub 1-x}Sr{sub x}CoO{sub 3} (x=0, 0.05) powders were prepared using the citrate-gel (Pechini) process. Pellets formed from these powders were sintered at various temperatures. All samples were characterized by means of X-Ray Diffraction and Scanning Electron Microscopy in order to investigate their structural and morphological properties. The electrical resistivity, thermal conductivity and thermopower were measured in a wide range of temperatures (2-350K) in order to understand the influence of the different processing conditions on the thermoelectric properties of the compounds.

36 MATERIALS SCIENCE↗

Investigation of tin oxide nanofibers synthesized via bio-template technique

In the present paper tin oxide nanofibers have been by synthesized using cotton as bio-template via sol-gel route. This is comparatively a new synthesis technique. The structure and morphology of the obtained SnO{sub 2} nanofibers were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDX). The optical properties of the same have been studied by using UV-Vis spectroscopy. The observed XRD pattern showed that peaks are very narrow and sharp which indicates crystalline nature of samples. SEM images gave an idea about the sample morphology and confirm that the obtained sample were nanofibers. The optical absorbance spectrum of the sample under study was recorded in UV-visible region (200nm- 800nm). The band gap of the sample was found to be 3.95 eV which is higher than their bulk counterpart.

36 MATERIALS SCIENCE↗

Growth and properties of crystalline CuInSe{sub 2} thin films by SPD technique

CuInSe{sub 2} thin films were grown on glass substrates using the chemical spray pyrolysis technique. The CuInSe{sub 2} films were co-deposited from aqueous solutions containing CuCl{sub 2}, InCl{sub 3}, and SeO{sub 2} used as Cu, In and Se precursors respectively. EDC was used as a complexing agent and films were grown at the constant temperature of 270°C. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Energy dispersive analysis of X-rays (EDAX) and the results indicate that the films are single phase, p-type in conductivity and have the chalcopyrite structure. Optical study shows that the optical band gap value is 1.03 eV. From the XRD study it is clear that the average crystallite size of the films is in the range 50 to 70 nm.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Preparation of ZnO:CeO{sub 2-x} thin films by AP-MOCVD: Structural and optical properties

The growth of columnar CeO{sub 2}, ZnO and ZnO:CeO{sub 2-x} films on quartz and AA6066 aluminum alloy substrates by economic atmospheric pressure metal-organic chemical vapor deposition (AP-MOCVD) is reported. A novel and efficient combination of metal acetylacetonate precursors as well as mild operating conditions were used in the deposition process. The correlation among crystallinity, surface morphology and optical properties of the as-prepared films was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), transmission electron microscopy (TEM) and UV-vis spectroscopy. The synthesized films showed different crystallographic orientations depending on the ZnO and CeO{sub 2} lattice mismatch, cerium content and growth rate. The CeO{sub 2} films synthesized in this work showed plate-like compact structures as a result of the growth process typical of CVD. Both pure and ZnO:CeO{sub 2-x} films were obtained with a hexagonal structure and highly preferred orientation with the c-axis perpendicular to both substrates under the optimal deposition conditions. The microstructure was modified from dense, short round columns to round structures with cavities ('rose-flower-like' structures) and the typical ZnO morphology by controlling the cerium doping the film and substrate nature. High optical transmittance (>87%) was observed in the pure ZnO films. As for the ZnO:CeO{sub 2-x} films, the optical transmission was decreased and the UV absorption increased, which subsequently was affected by an increase in cerium content. This paper assesses the feasibility of using ZnO:CeO{sub 2-x} thin films as UV-absorbers in industrial applications. - Graphical abstract: TEM micrographs and their corresponding SAED pattern obtained for the as-deposited ZnO-CeO{sub 2-x} thin films for a Zn/Ce metallic ratio 16:9.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Transport properties near the metal to insulator transition in samarium substituted (Bi,Pb)-2212 system

The electrical transport properties of insulating and superconducting samples of Bi{sub 1.7}Pb{sub 0.4}Sr{sub 2-x}Sm{sub x}Ca{sub 1.1}Cu{sub 2.1}O{sub 8+d}elta system is studied across the metal to insulator transition (MIT) region by varying the x values from 0.5 to 1.0 in steps of 0.1. X-ray diffraction analysis, scanning electron microscopy, energy dispersive x-ray analysis (EDAX), and electrical resistivity measurements have been employed for the characterization of all samples. The x-ray and EDAX analyses indicate that samarium (Sm) atoms are incorporated into the crystalline structure of Bi{sub 1.7}Pb{sub 0.4}Sr{sub 2}Ca{sub 1}Cu{sub 2}O{sub 8+d}elta[(Bi,Pb)-2212]. Samples with x<=0.6 undergo superconducting transitions while those with 0.7<=x<=1.0 exhibit semiconducting behavior. The MIT is observed at 0.6<x<=0.7 with a suppression in superconductivity. The results show that with increase in temperature, the transport mechanism of the semiconducting samples transits from two dimensional variable range hopping to thermally activated conduction. A scaling model is presented for the MIT and the results are interpreted on the basis of hole filling and disorder due to the substitution of Sm at the strontium site of (Bi,Pb)-2212 system.

36 MATERIALS SCIENCE↗

Effect of nitrogen-doping temperature on the structure and photocatalytic activity of the B,N-doped TiO{sub 2}

B,N-TiO{sub 2} photocatalysts were synthesized by boron doping firstly and subsequently nitrogen doping in NH{sub 3} at variable temperatures. The effects of the nitrogen doping temperature on the structure and photocatalytic activity of the B,N-codoped TiO{sub 2} were investigated. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), UV-vis diffuse reflectance spectrum (DRS), electron paramagnetic resonance (EPR) and X-ray photoelectron spectroscopy (XPS). The photocatalytic activity was evaluated with photocatalytic degradation of methyl orange dye (MO) under visible light and UV-visible light irradiation. The results suggested that the boron and nitrogen can be incorporated into the TiO{sub 2} lattice either interstitially or substitutionally or both, while the Ti-O-B-N structure plays a vital role in photocatalytic activity in visible light region. The optimal nitrogen doping temperature is 550 {sup o}C. Higher temperature may form many oxygen vacancies and Ti{sup 3+} species, resulting in the decrease of photocatalytic activity in visible light. -- Graphical abstract: The changes of photocatalytic activity of B,N-TiO{sub 2} with variable nitrogen doping temperatures are attributed to the transformation of surface structure and oxygen vacancies, and the Ti-O-B-N structure plays a vital role in photocatalytic activity under visible light irradiation. Display Omitted Research highlights: > B,N-TiO{sub 2} photocatalysts are synthesized by boron doping firstly and subsequently nitrogen doping in NH{sub 3} at variable temperatures. > The boron and nitrogen can be incorporated into the TiO{sub 2} lattice either interstitially or substitutionally or both. > The temperature of nitrogen doping affects the transformation of surface structure and oxygen vacancies. > The Ti-O-B-N structure plays an important role in photocatalytic activity under visible light irradiation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗