Search NASA⌕ Search

SEARCH · Search NASA

Results for “ACID”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Effect of acetic acid on lipid accumulation by glucose-fed activated sludge cultures

The effect of acetic acid, a lignocellulose hydrolysis by-product, on lipid accumulation by activated sludge cultures grown on glucose was investigated. This was done to assess the possible application of lignocellulose as low-cost and renewable fermentation substrates for biofuel feedstock production. Results: Biomass yield was reduced by around 54% at a 2 g L -1 acetic acid dosage but was increased by around 18% at 10 g L -1 acetic acid dosage relative to the control run. The final gravimetric lipid contents at 2 and 10 g L -1 acetic acid levels were 12.5 + 0.7% and 8.8 + 3.2% w/w, respectively, which were lower than the control (17.8 + 2.8% w/w). However, biodiesel yields from activated sludge grown with acetic acid (5.6 + 0.6% w/w for 2 g L -1 acetic acid and 4.2 + 3.0% w/w for 10 g L -1 acetic acid) were higher than in raw activated sludge (1-2% w/w). The fatty acid profiles of the accumulated lipids were similar with conventional plant oil biodiesel feedstocks. Conclusions: Acetic acid enhanced biomass production by activated sludge at high levels but reduced lipid production. Further studies are needed to enhance acetic acid utilization by activated sludge microorganisms for lipid biosynthesis.

Biodiesel, fermentation, inhibitors, lignocellulos↗

Folic acid-CdTe quantum dot conjugates and their applications for cancer cell targeting

In this study, we report the preparation,luminescence, and targeting properties of folic acid- CdTe quantum dot conjugates. Water-soluble CdTe quantum dots were synthesized and conjugated with folic acid using 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide-N-hydroxysuccinimide chemistry. The in-fluence of folic acid on the luminescence properties of CdTe quantum dots was investigated, and no energy transfer between them was observed. To investigate the efficiency of folic acid-CdTe nanoconjugates for tumor targeting, pure CdTe quantum dots and folic acid-coated CdTe quantum dots were incubated with human naso- pharyngeal epidermal carcinoma cell line with positive expressing folic acid receptors (KB cells) and lung cancer cells without expression of folic acid receptors (A549 cells). For the cancer cells with positive folate receptors (KB cells), the uptake for CdTe quantum dots is very low, but for folic acid-CdTe nanoconjugates, the uptake is very high. For the lung cancer cells without folate receptors (A549 cells), the uptake for folic acid- CdTe nanoconjugates is also very low. The results indicate that folic acid is an effective targeting molecule for tumor cells with overexpressed folate receptors.

Suriamoorthy, Preethi↗

Acid Strength and Bifunctional Catalytic Behavior of Alloys Comprised of Noble Metals and Oxophilic Metal Promoters

The promotion of metal catalysts with partially oxidized oxophilic MOx species, such as ReOx-promoted Rh, has been demonstrated to produce Brønsted acid sites that can promote hydrogenolysis of oxygenate intermediates such as those found in biomass-derived species. A wide variety of alloy compositions and structures are examined in this work to investigate strongly acidic promoters by using DFT-calculated deprotonation energies (DPE) as a measure of acid strength. Sites with the highest acid strength had DPE less than 1100 kJ mol-1, similar to DPE values of heteropolyacids or acid-containing zeolites, and were found on alloys composed of an oxophilic metal (such as Re or W) with a noble metal (such as Rh or Pt). NH3 adsorbs more strongly to sites with increasing acid strength and the activation barriers for acid-catalyzed ring opening of a furan ring decrease with increasing acid strength, which was also shown to be stronger for OH acid sites bound to multiple oxophilic metal atoms in a three-fold configuration rather than OH sites adsorbed in an atop configuration on one oxophilic metal, indicating that small MOx clusters may yield sites with the highest acid strength.

Environmental Molecular Sciences Laboratory↗

Acid–base catalysis over perovskites: a review

We present that perovskite catalysts have been extensively studied for reduction–oxidation (redox) reactions; however, their acid–base catalytic properties are still under-explored. This review collects work aiming to study the acid–base catalytic properties of perovskites. Reports regarding combined acid–base/redox catalysis over perovskites lie beyond the scope of the present review. For the characterization of acid–base properties, researchers have studied the interaction of probe molecules with perovskite surfaces by means of multiple techniques that provide information about the density, strength and type of adsorption sites. The top-surface composition of perovskites, which relates to the abundance of the acid–base sites, has been studied by means of low energy ion scattering (LEIS), and, the less surface sensitive, conventional X-ray photoelectron spectroscopy (XPS). Probe reactions, with the conversion of 2-propanol as the common choice, have also been employed for characterizing the acid–base catalytic properties of perovskites. The complex nature of perovskite surfaces, which explains the still absent fundamental relations between the structure of the catalyst and reaction rates/selectivity, encounters a great challenge due to the surface reconstruction of these materials. In this review, we devote a special section to highlight recent publications that report the impact of surface reconstruction and particle shape on acid–base catalysis over perovskites. In addition, we review promising catalytic performances of perovskite catalysts for other reactions of interest. Challenges in acid–base catalysis over perovskites focus on the development of time-resolved monolayer-sensitive characterization of surfaces under operando conditions and the discernment of combined acid–base/redox reaction mechanisms. Finally, opportunities lay on tuning the acid–base characteristics of perovskites with computation-based catalytic descriptors to achieve desired selectivities and enhanced rates.

36 MATERIALS SCIENCE↗

Interfacial acidity on the strontium titanate surface: a scaling paradigm and the role of the hydrogen bond

A fundamental understanding of acidity at an interface, as mediated by structure and molecule–surface interactions, is essential to elucidate the mechanisms of a range of chemical transformations. While the strength of an acid in homogeneous gas and solution phases is conceptually well understood, acid–base chemistry at heterogeneous interfaces is notoriously more complicated. Using density functional theory and nonlinear vibrational spectroscopy, we present a method to determine the interfacial Brønsted–Lowry acidity of aliphatic alcohols adsorbed on the (100) surface of the model perovskite, strontium titanate. Here, while shorter and less branched alkanols are known to be less acidic in the gas phase and more acidic in solution, here we show that shorter alcohols are less acidic whereas less substituted alkanols are more acidic at the gas–oxide interface. Hydrogen bonding plays a critical role in defining acidity, whereas structure–acidity relationships are dominated by van der Waals interactions between the alcohol and the surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Arabidopsis cytochrome b 5 proteins support fatty acid ω-3 but not ω-6 desaturation

Fatty acids are primary components of lipids, which serve as major energy sources in cells and play essential roles in membrane structure, signaling, and metabolic regulation (Shanklin and Cahoon 1998). The degree of fatty acid unsaturation critically influences lipid physicochemical properties, thereby affecting membrane fluidity and biological function (Nguyen et al. 2019). In Arabidopsis thaliana, fatty acid desaturation occurs via 2 parallel pathways: the “prokaryotic pathway” in plastids, involving glycosylglycerides, such as monogalactosyldiacylglycerol (MGDG) and digalactosyldiacylglycerol (DGDG), and phospholipid phosphatidylglycerol (PG); and the “eukaryotic pathway” in the endoplasmic reticulum (ER), involving phosphatidylcholine (PC) (Lou et al. 2014) (Supplementary Figure S1). Seven fatty acid desaturases (FADs) in Arabidopsis differentially desaturate each glycerolipid class in the plastid and ER (Nguyen et al. 2019). FAD2, an ER-resident ω-6 fatty acid desaturase, catalyzes the conversion of oleic acid (18:1) to linoleic acid (18:2), which can be further desaturated to α-linolenic acid (18:3) by FAD3, an ER-resident ω-3 fatty acid desaturase. In plastids, FAD6 catalyzes the desaturation of 18:1/16:1 to produce 18:2/16:2, while FAD7 and FAD8 redundantly convert 18:2/16:2 to 18:3/16:3 (Li-Beisson et al. 2013; Nguyen et al. 2019). Additionally, fatty acids synthesized in the ER can also be reimported into plastids to their site of de novo synthesis (Xu et al. 2010). All FADs require reducing power, in the form of 2 electrons, for catalysis, but the sources of the electrons vary between their subcellular localizations. In the ER, FAD2 and FAD3 receive electrons from a cytochrome b 5 (CB5)-based electron transfer chain comprising cytochrome b 5 reductase (CBR) and CB5. In contrast, ferredoxin serves as the electron donor for plastid-localized FAD6, FAD7, and FAD8 (Ohlrogge and Browse 1995; Andreu et al. 2007). While the relative contributions of the 2 pathways to total cellular desaturation products vary across tissues and species, most polyunsaturated FA biosynthesis in seeds occurs via ER-resident FAD2 and FAD3 (Miquel and Browse 1992; Ohlrogge and Browse 1995).

59 BASIC BIOLOGICAL SCIENCES↗

Physiological responses of Daphnia pulex to acid stress

Background: Acidity exerts a determining influence on the composition and diversity of freshwater faunas. While the physiological implications of freshwater acidification have been intensively studied in teleost fish and crayfish, much less is known about the acid-stress physiology of ecologically important groups such as cladoceran zooplankton. This study analyzed the extracellular acid-base state and CO 2 partial pressure (P CO 2 ), circulation and ventilation, as well as the respiration rate of Daphnia pulex acclimated to acidic (pH 5.5 and 6.0) and circumneutral (pH 7.8) conditions. Results: D. pulex had a remarkably high extracellular pH of 8.33 and extracellular P CO 2 of 0.56 kPa under normal ambient conditions (pH 7.8 and normocapnia). The hemolymph had a high bicarbonate concentration of 20.9 mM and a total buffer value of 51.5 meq L -1 pH -1 . Bicarbonate covered 93% of the total buffer value. Acidic conditions induced a slight acidosis (ΔpH = 0.16–0.23), a 30–65% bicarbonate loss, and elevated systemic activities (tachycardia, hyperventilation, hypermetabolism). pH 6.0 animals partly compensated the bicarbonate loss by increasing the nonbicarbonate buffer value from 2.0 to 5.1 meq L -1 pH -1 . The extracellular P CO 2 of pH 5.5 animals was significantly reduced to 0.33 kPa, and these animals showed the highest tolerance to a short-term exposure to severe acid stress. Conclusion: Chronic exposure to acidic conditions had a pervasive impact on Daphnia's physiology including acid-base balance, extracellular P CO 2 , circulation and ventilation, and energy metabolism. Compensatory changes in extracellular non-bicarbonate buffering capacity and the improved tolerance to severe acid stress indicated the activation of defense mechanisms which may result from gene-expression mediated adjustments in hemolymph buffer proteins and in epithelial properties. Mechanistic analyses of the interdependence between extracellular acid-base balance and CO 2 transport raised the question of whether a carbonic anhydrase (CA) is involved in the catalysis of the CO 2 -HCO $\overline{3}$ -H + reaction, which led to the discovery of 31 CA-genes in the genome of D. pulex.

59 BASIC BIOLOGICAL SCIENCES↗

Biogeography of microbial bile acid transformations along the murine gut

Bile acids, which are synthesized from cholesterol by the liver, are chemically transformed along the intestinal tract by the gut microbiota, and the products of these transformations signal through host receptors, affecting overall host health. These transformations include bile acid deconjugation, oxidation, and 7α-dehydroxylation. An understanding of the biogeography of bile acid transformations in the gut is critical because deconjugation is a prerequisite for 7α-dehydroxylation and because most gut microorganisms harbor bile acid transformation capacity. Here, we used a coupled metabolomic and metaproteomic approach to probe in vivo activity of the gut microbial community in a gnotobiotic mouse model. Results revealed the involvement of Clostridium scindens in 7α-dehydroxylation, of the genera Muribaculum and Bacteroides in deconjugation, and of six additional organisms in oxidation (the genera Clostridium, Muribaculum, Bacteroides, Bifidobacterium, Acutalibacter, and Akkermansia). Furthermore, the bile acid profile in mice with a more complex microbiota, a dysbiosed microbiota, or no microbiota was considered. For instance, conventional mice harbor a large diversity of bile acids, but treatment with an antibiotic such as clindamycin results in the complete inhibition of 7α-dehydroxylation, underscoring the strong inhibition of organisms that are capable of carrying out this process by this compound. Finally, a comparison of the hepatic bile acid pool size as a function of microbiota revealed that a reduced microbiota affects host signaling but not necessarily bile acid synthesis. In this study, bile acid transformations were mapped to the associated active microorganisms, offering a systematic characterization of the relationship between microbiota and bile acid composition.

59 BASIC BIOLOGICAL SCIENCES↗

Data from pH Selectively Regulates Citric Acid and Lipid Production in Yarrowia lipolytica W29 During Nitrogen-limited Growth on Glucose

Yarrowia lipolytica has been used to produce both citric acid and lipid-based bioproducts at high titers. In this study, we found that pH differentially affects citric acid and lipid production in Y. lipolytica W29, with citric acid production enhanced at more neutral pH’s and lipid production enhanced at more acid pH’s. To determine the mechanism governing this pH-dependent switch between citric acid and lipid production, we profiled gene expression at different pH’s and found that the relative expression of multiple transporters is increased at neutral pH. These results suggest that this pH-dependent switch is mediated at the level of citric acid transport rather than changes in the expression of the enzymes involved in citric acid and lipid metabolism. In further support of this mechanism, thermodynamic calculations suggest that citric acid secretion is more energetically favorable at neutral pH’s, assuming the fully protonated acid is the substrate for secretion. Collectively, these results provide new insights regarding citric acid and lipid production in Y. lipolytica and may offer new strategies for metabolic engineering and process design.

Conversion↗

A Novel Dew Point Meter: Application to the Measurement of the Sulfuric Acid Dew Point for Combustion Flue Gas

Accurate knowledge of acid dew point is essential for industrial and applied combustion applications. Sulfur in the fuel or raw materials is converted to sulfur dioxide (SO2) during combustion, and a portion of the SO2 is oxidized to sulfur trioxide (SO3). The SO3 will react to form H2SO4 vapor when in the presence of water vapor. Even with just trace levels of H2SO4 vapor in the gas phase (1-10 ppm), the dew point can reach 100°C and higher. To avoid acid condensation and the resulting corrosion on heat recovery equipment, plant engineers must ensure that surface temperatures are above the acid dew point, but this decreases the efficiency of thermal energy recovery. Thus, there is a trade-off between minimizing equipment corrosion and maximizing thermal energy recovery, and the acid dew point is a key parameter for this optimization. Commercially available acid dew point meters use electric conductivity sensors. These sensors are known to greatly underestimate the dew point due to their low sensitivity. In addition, no validation testing has been reported for these units and they are often expensive. In this work, we analyze the theory of the sulfuric acid condensation and develop a novel dew point meter based on this analysis. The meter consists of a novel optical instrument that is designed to monitor the slightest appearance of condensation on a hydrophobic window surface as the surface temperature of the window is slowly decreased. In this way, an accurate measurement of the dew point is obtained under a wide range of concentrations. The basis of the instrument is that a collimated beam from a diode laser will generate forward scattered light when the beam encounters surface condensate, and a sophisticated array detector is used to sensitively monitor the onset of light scattering. The measurement procedures are established to rapidly find the acid dew point, while minimizing error. Further, to calibrate the dew point meter we developed a calibration system based on a liquid bubbler that can generate a stable gas flow with a known sulfuric acid dew point. Test results show that the dew point meter can accurately measure acid dew point over a wide range. For H2SO4 vapor concentrations as low as 6 ppm the acid dew point is measured with an error of only ~1°C. To demonstrate the versatility of this instrument, the dew point meter was adapted for use with a high-pressure flow cell to allow for measurements of the dew point of flue gas from pressurized oxy-fuel combustion in a 100 kWth pressurized reactor.

Cheng, Mao↗

The acidity of atmospheric particles and clouds

Acidity, defined as pH, is a central component of aqueous chemistry. In the atmosphere, the acidity of condensed phases (aerosol particles, cloud water, and fog droplets) governs the phase partitioning of semivolatile gases such as HNO 3 , NH 3 , HCl, and organic acids and bases as well as chemical reaction rates. It has implications for the atmospheric lifetime of pollutants, deposition, and human health. Despite its fundamental role in atmospheric processes, only recently has this field seen a growth in the number of studies on particle acidity. Even with this growth, many fine-particle pH estimates must be based on thermodynamic model calculations since no operational techniques exist for direct measurements. Current information indicates acidic fine particles are ubiquitous, but observationally constrained pH estimates are limited in spatial and temporal coverage. Clouds and fogs are also generally acidic, but to a lesser degree than particles, and have a range of pH that is quite sensitive to anthropogenic emissions of sulfur and nitrogen oxides, as well as ambient ammonia. Historical measurements indicate that cloud and fog droplet pH has changed in recent decades in response to controls on anthropogenic emissions, while the limited trend data for aerosol particles indicate acidity may be relatively constant due to the semivolatile nature of the key acids and bases and buffering in particles. This paper reviews and synthesizes the current state of knowledge on the acidity of atmospheric condensed phases, specifically particles and cloud droplets. It includes recommendations for estimating acidity and pH, standard nomenclature, a synthesis of current pH estimates based on observations, and new model calculations on the local and global scale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrochemical formation of hydroxide for enhancing carbon dioxide and acid gas uptake by a solution

A system is described for forming metal hydroxide from a metal carbonate utilizing a water electrolysis cell having an acid-producing anode and a hydroxyl-producing cathode immersed in a water solution of sufficient ionic content to allow an electric current to pass between the hydroxyl-producing cathode and the acid-producing anode. A metal carbonate, in particular water-insoluble calcium carbonate or magnesium carbonate, is placed in close proximity to the acid-producing anode. A direct current electrical voltage is provided across the acid-producing anode and the hydroxyl-producing cathode sufficient to generate acid at the acid-producing anode and hydroxyl ions at the hydroxyl-producing cathode. The acid dissolves at least part of the metal carbonate into metal and carbonate ions allowing the metal ions to travel toward the hydroxyl-producing cathode and to combine with the hydroxyl ions to form the metal hydroxide. The carbonate ions travel toward the acid-producing anode and form carbonic acid and/or water and carbon dioxide. Among other uses, the metal hydroxide formed can be employed to absorb acid gases such as carbon dioxide from a gas mixture. The invention can also generate hydrogen and oxidative gases such as oxygen or chlorine.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

L–malic acid production from xylose by engineered Saccharomyces cerevisiae

L-malic acid is widely used in the food, chemical, and pharmaceutical industries. Here, we report on production of malic acid from xylose, the second most abundant sugar in lignocellulosic hydrolysates, by engineered Saccharomyces cerevisiae. To enable malic acid production in a xylose-assimilating S. cerevisiae, we overexpressed PYC1 and PYC2, coding for pyruvate carboxylases, a truncated MDH3 coding for malate dehydrogenase, and SpMAE1, coding for a Schizosaccharomyces pombe malate transporter. Additionally, both the ethanol and glycerol-producing pathways were blocked to enhance malic acid production. The resulting strain produced malic acid from both glucose and xylose, but it produced much higher titers of malic acid from xylose than glucose. Interestingly, the engineered strain had higher malic acid yield from lower concentrations (10 g L –1 ) of xylose, with no ethanol production, than from higher xylose concentrations (20 and 40 g L –1 ). As such, a fed-batch culture maintaining xylose concentrations at low levels was conducted and 61.2 g L –1 of malic acid was produced, with a productivity of 0.32 g L –1 h. Furthermore, these results represent successful engineering of S. cerevisiae for the production of malic acid from xylose, confirming that that xylose offers the efficient production of various biofuels and chemicals by engineered S. cerevisiae.

59 BASIC BIOLOGICAL SCIENCES↗

Tissue-specific differences in metabolites and transcripts contribute to the heterogeneity of ricinoleic acid accumulation in Ricinus communis L. (castor) seeds

Castor ( Ricinus communis L.) seeds are valued for their production of oils which can comprise up to 90% hydroxy-fatty acids (ricinoleic acid). Castor oil contains mono-, di- and tri- ricinoleic acid containing triacylglycerols (TAGs). Although the enzymatic synthesis of ricinoleic acid is well described, the differential compartmentalization of these TAG molecular species has remained undefined. To examine the distribution of hydroxy fatty acid accumulation within the endosperm and embryo tissues of castor seeds. Matrix assisted laser desorption/ionization mass spectrometry imaging (MALDI-MSI) was used to map the distribution of triacylglycerols in tissue sections of castor seeds. In addition, the endosperm and embryo (cotyledons and embryonic axis) tissues were dissected and extracted for quantitative lipidomics analysis and Illumina-based RNA deep sequencing. Results: This study revealed an unexpected heterogeneous tissue distribution of mono-, di- and tri- hydroxy-triacylglycerols in the embryo and endosperm tissues of castor seeds. Pathway analysis based on transcript abundance suggested that distinct embryo- and endosperm-specific mechanisms may exist for the shuttling of ricinoleic acid away from phosphatidylcholine (PC) and into hydroxy TAG production. The embryo-biased mechanism appears to favor removal of ricinoleic acid from PC through phophatidylcholine: diacylglycerol acylytransferase (PDAT) while the endosperm pathway appears to remove ricinoleic acid from the PC pool by preferences of phospholipase A (PLA 2 α) and/or phosphatidylcholine: diacylglycerol cholinepshphotransferase PDCT. In conclusion, collectively, a combination of lipidomics and transcriptomics analyses revealed previously undefined spatial aspects of hydroxy fatty acid metabolism in castor seeds. These studies underscore a need for tissue-specific studies as a means to better understand the regulation of triacylglycerol accumulation in oilseeds.

59 BASIC BIOLOGICAL SCIENCES↗

Citric Acid-Modified Fenton's Reaction for the Oxidation of Chlorinated Ethylenes in Soil Solution Systems

Fenton's reagent, a solution of hydrogen peroxide and ferrous iron catalyst, is used for an in-situ chemical oxidation of organic contaminants. Sulfuric acid is commonly used to create an acidic condition needed for catalytic oxidation. Fenton's reaction often involves pressure buildup and precipitation of reaction products, which can cause safety hazards and diminish efficiency. We selected citric acid, a food-grade substance, as an acidifying agent to evaluate its efficiencies for organic contaminant removal in Fenton's reaction, and examined the impacts of using citric acid on the unwanted reaction products. A series of batch and column experiments were performed with varying H{sub 2}O{sub 2} concentrations to decompose selected chlorinated ethylenes. Either dissolved iron from soil or iron sulfate salt was added to provide the iron catalyst in the batch tests. Batch experiments revealed that both citric and sulfuric acid systems achieved over 90% contaminant removal rates, and the presence of iron catalyst was essential for effective decontamination. Batch tests with citric acid showed no signs of pressure accumulation and solid precipitations, however the results suggested that an excessive usage of H{sub 2}O{sub 2} relative to iron catalysts (Fe{sup 2+}/H{sub 2}O{sub 2} < 1/330) would result in lowering the efficiency of contaminant removal by iron chelations in the citric acid system. Column tests confirmed that citric acid could provide suitable acidic conditions to achieve higher than 55% contaminant removal rates.

54 ENVIRONMENTAL SCIENCES↗

An integrated biorefinery approach to obtain xylo-oligosaccharides from corncob using lactic acid-rich fermentation broth

Although xylo-oligosaccharides production from lignocelluloses via lactic acid hydrolysis is advantageous in terms of high yields with less by-products, the use of high purity lactic acid inevitably increases the cost of xylo-oligosaccharides production. The utilization of lactic acid-rich fermentation broth for xylo-oligosaccharides production can avoid the separation and purification of lactic acid. However, the feasibility of lactic acid-rich fermentation broth for xylo-oligosaccharides production from lignocelluloses was unclear. In this work, the results indicated that the highest xylo-oligosaccharides yield of 72% was obtained from corncob by lactic acid-rich fermentation broth pretreatment and xylanase hydrolysis. Subsequently, monosaccharides-rich hydrolysate (90.9 g/L) was obtained from solid residues of corncob by cellulase hydrolysis. Lactic acid-rich fermentation broth was produced by Weizmannia coagulans fermentation of the monosaccharide-rich hydrolysate. Besides, the obtained xylo-oligosaccharides and lactic acid mixture might be used as feed additives, avoiding the purification and separation of lactic acid or xylo-oligosaccharides. Meanwhile, the production cost of feed grade xylo-oligosaccharides from this work was much lower than the current market price. Overall, this work proposed a new strategy for efficient and environmental-friendly production of xylo-oligosaccharides from corncob.

09 BIOMASS FUELS↗

Bilayer Structure and Lipid Dynamics in a Model Stratum Corneum with Oleic Acid

The stratum corneum is the uppermost layer of the skin and acts as a barrier to keep out contaminants and retain moisture. Understanding the molecular structure and behavior of this layer will provide guidance for optimizing its biological function. In this study we use a model mixture comprised of equimolar portions of ceramide NS (24:0), lignoceric acid, and cholesterol to model the effect of the addition of small amounts of oleic acid to the bilayer at 300 and 340 K. Five systems at each temperature have been simulated with concentrations between 0 and 0.1 mol % oleic acid. Our major finding is that subdiffusive behavior over the 200 ns time scale is evident in systems at 340 K, with cholesterol diffusion being enhanced with increased oleic acid. Importantly, cholesterol and other species diffuse faster when radial densities indicate nearest neighbors include more cholesterol. We also find that, with the addition of oleic acid, the bilayer midplane and interfacial densities are reduced and there is a 3% decrease in total thickness occurring mostly near the hydrophilic interface at 300 K with reduced overall density at 340 K. Increased interdigitation occurs independent of oleic acid with a temperature increase. Slight ordering of the long non-hydroxy fatty acid of the ceramide occurs near the hydrophilic interface as a function of the oleic acid concentration, but no significant impact on hydrogen bonding is seen in the chosen oleic acid concentrations.

08 HYDROGEN↗

Glycolic-Nitric Acid Flowsheet Demonstration of the DWPF Chemical Processing Cell with Matrix Simulants and Supernate

Savannah River Remediation (SRR) is evaluating changes to its current DWPF flowsheet to improve processing cycle times. This will enable the facility to support higher canister production while maximizing waste loading. Higher throughput is needed in the CPC since the installation of the bubblers into the melter has increased melt rate. Due to the significant maintenance required for the DWPF gas chromatographs (GC) and the potential for production of flammable quantities of hydrogen, reducing or eliminating the amount of formic acid used in the CPC is being developed. Earlier work at Savannah River National Laboratory has shown that replacing formic acid with an 80:20 molar blend of glycolic and formic acids has the potential to remove mercury in the SRAT without any significant catalytic hydrogen generation. This report summarizes the research completed to determine the feasibility of processing without formic acid. In earlier development of the glycolic-formic acid flowsheet, one run (GF8) was completed without formic acid. It is of particular interest that mercury was successfully removed in GF8, no formic acid at 125% stoichiometry. Glycolic acid did not show the ability to reduce mercury to elemental mercury in initial screening studies, which is why previous testing focused on using the formic/glycolic blend. The objective of the testing detailed in this document is to determine the viability of the nitric-glycolic acid flowsheet in processing sludge over a wide compositional range as requested by DWPF. This work was performed under the guidance of Task Technical and Quality Assurance Plan (TT and QAP). The details regarding the simulant preparation and analysis have been documented previously.

08 HYDROGEN↗