Search NASA⌕ Search

SEARCH · Search NASA

Results for “Configuration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Conceptual Design Aspects of Three General Sub-Classes of Multi-Rotor Configurations: Distributed, Modular, and Heterogeneous

Quadcopters and other multi-rotor configurations are poised to make a substantial contribution to commercial and public service aviation. Small multi-rotor configurations already see almost ubiquitous use as radio-controlled toys and hobbyist platforms. In particular, their use as flying cameras has seen rapid adoption by the public. But their greatest contribution to our society may likely be seen in public service missionsapplications. Their potential utility for supporting emergency response missions is discussed in some detail. The multi-rotor design space is then explored from high-level perspective with the emphasis on distributed, modular, and heterogeneous multi-rotor systems. Following this design space examination, a number of specific, detailed technical issues related multi-rotor conceptual design and sizing is also considered.

Configurations↗
NASA NTRS2021

Transition Analysis for the CRM-NLF Wind Tunnel Configuration

This paper reports the results of a comprehensive linear stability analysis of the boundary layer flow over the common research model with natural laminar flow (CRM-NLF) aircraft configuration. The flow conditions match selected test conditions from a recent wind tunnel experiment in the National Transonic Facility at the NASA Langley Research Center. Previous work has shown that the measured onset of laminar-turbulent transition during the experiments can be correlated with the linear amplification of Tollmien-Schlichting (TS) and stationary crossflow (CF) instabilities in the swept wing boundary layer. However, a significant scatter ( N ∈ (4,9)) was observed in the values of the logarithmic amplification factor along the measured transition front. This previous analysis was based on an approximate basic state (based on a boundary layer code with conical flow approximation) and parallel stability computations without surface curvature effects. Here, we examine the effects of these various approximations with the goal of quantifying the resulting changes in the N-factor correlations. Specifically, both linear stability theory (LST) and the parabolized stability equations (PSE)are used in conjunction with an accurate definition of the laminar boundary layer flow as computed with a Navier-Stokes solver with a Reynolds-Averaged-Navier-Stokes (RANS) based turbulence model within the turbulent parts of the flow. Furthermore, the effects of instability wave propagation within a fully three-dimensional boundary layer are also evaluated by integrating the disturbance growth rates along suitably chosen, curvilinear (i.e., nonplanar) propagation trajectories. The results of this analysis are also used in an accompanying paper by Venkatachari et al. to develop improved, physics based transition predictions for the same CRM-NLF configuration.

Boundary layer transition↗
NASA NTRSDate not supplied

POIWG #53 Vehicle Configuration Overview

The Vehicle Configuration Team is composed of the MAGIK, CAMMP, and IPiP groups who function to model and analyze the internal and external configurations of the ISS, plug-in power allocations, as well as the movement of the robotic arms around the station.

Vehicle↗
DOE OSTI2023

Formation of Amorphous Carbon Multi‐Walled Nanotubes from Random Initial Configurations

Amorphous carbon nanotubes (a‐CNT) with up to four walls and sizes ranging from 200 to 3200 atoms have been simulated, starting from initial random configurations and using the Gaussian Approximation Potential. The important variables (like density, height, and diameter) required to successfully simulate a‐CNTs were predicted with the machine learning random forest technique. The width of the a‐CNT models ranged between 0.55–2 nm with an average inter‐wall spacing of 0.31 nm. The topological defects in a‐CNTs were analyzed and new defect configurations were observed. The electronic density of states and localization in these phases were discussed and delocalized electrons in the π subspace were identified as an important factor for inter‐layer cohesion. Spatial projection of the electronic conductivity favors axial transport along connecting hexagons, while non‐hexagonal parts of the network either hinder or bifurcate the electronic transport. A vibrational density of states was calculated and is potentially an experimentally comparable fingerprint of the material. The appearance of a low‐frequency radial breathing mode was discussed and the thermal conductivity at 300 K was estimated using the Green‐Kubo formula.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Bottom‐Up Synthesis of Metallic CoNi Nanoplatelets with Magnetic Vortex‐Like Spin Configurations

Magnetic nanoplatelets hold significant potential for various technical applications due to their ability to switch between a fully magnetized state with high magnetization and a vortex‐like configuration that eliminates stray fields in the absence of an external field. This study presents the synthesis of uniform CoNi nanoplatelets through the topotactic reduction of metal hydroxides using hydrogen plasma. The reduction process is analyzed via magnetometry, leveraging the transition from paramagnetic hydroxide to ferromagnetic metal. Lorentz transmission electron microscopy and scanning transmission X‐ray microscopy confirm the presence of magnetic vortex‐like structures in isolated Co 0.85 Ni 0.15 nanoplatelets at ambient temperature. Additionally, micromagnetic simulations are conducted to further explore the magnetic properties of the nanoplatelets, revealing the formation of magnetic vortex remanent states at diameters between 200 nm and 1 μm and a thickness of around 12 nm. Notably, structural defects and thickness variations do not directly destabilize the magnetic vortex configurations.

Kräenbring, Mena‐Alexander [Faculty of Physics and↗
DOE OSTI2025

Friction Self-piercing Riveting Process for 3T Configuration of AA7075-AA7075-AA6022

Friction self-piercing riveting (F-SPR), as a solid-state joining process that generates frictional heat during the process, was utilized to join a 3 T configuration of low-ductility AA7075-AA7075-AA6022 sheets. A multi-step F-SPR process was employed to precisely control the mechanical interlocking and solid-state joining, ensuring a strong joint formation. With control of the plunge depth when the transition from rivet penetration to rivet flaring, two joining conditions were developed to assess mechanical joint integrity: one bearing deep penetration with a smaller interlock, and the other yielding a shallow penetration with a larger interlock. Both strategies met the criteria for a sound rivet joint. Customized lap shear tensile configurations were designed to assess the joint strength at interface between first and second layers, as well as between second and third layers. Both conditions demonstrated great joint strength between the first and second layers, while deeper penetration approach showed stronger solid-state joint, leading to improved joint strength between the second and third layers.

Wang, Tianzhao [ORNL] (ORCID:0000000315337602)↗
DOE OSTI2021

Coaction and double-copy properties of configuration-space integrals at genus zero

We investigate configuration-space integrals over punctured Riemann spheres from the viewpoint of the motivic Galois coaction and double-copy structures generalizing the Kawai-Lewellen-Tye (KLT) relations in string theory. For this purpose, explicit bases of twisted cycles and cocycles are worked out whose orthonormality simplifies the coaction. We present methods to efficiently perform and organize the expansions of configuration-space integrals in the inverse string tension α' or the dimensional-regularization parameter ϵ of Feynman integrals. Generating-function techniques open up a new perspective on the coaction of multiple polylogarithms in any number of variables and analytic continuations in the unintegrated punctures. We present a compact recursion for a generalized KLT kernel and discuss its origin from intersection numbers of Stasheff polytopes and its implications for correlation functions of two-dimensional conformal field theories. We find a non-trivial example of correlation functions in (p, 2) minimal models, which can be normalized to become uniformly transcendental in the p → ∞ limit.

Conformal Field Theory↗
DOE OSTI2021

Temperature-Dependent Configurational Entropy Calculations for Refractory High-Entropy Alloys

The cluster expansion formalism for alloys is used to construct surrogate models for three refractory high-entropy alloys (NbTiVZr, HfNbTaTiZr, and AlHfNbTaTiZr). These cluster expansion models are then used along with Monte Carlo methods and thermodynamic integration to calculate the configurational entropy of these refractory high-entropy alloys as a function of temperature. Many solid solution alloy design guidelines are based on the ideal entropy of mixing, which increases monotonically with N , the number of elements in the alloy. However, our results show that at low temperatures, the configurational entropy of these materials is largely independent of N , and the assumption described above only holds in the high-temperature limit. This suggests that alloy design guidelines based on the ideal entropy of mixing require further examination.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Low-energy effective quantum field theoretic description of excitations about soliton configurations

Solitons are the classical field configurations connecting two trivial vacua. These are also the solutions of classical field equations of motion with particle-like properties. Moreover, they are localized in space, having finite energy, and are stable against decay into radiation. The coherent state description of kink-solitons is discussed in the present article. Further, the relation between topological solitons and occupation numbers corresponding to low momentum excitations are also discussed coherently. The description of the low energy excitations about solitons in quantum field theory is the main theme of this article. Further, a few physical observables, namely some low order correlation functions, are computed up to certain integral forms. Furthermore, we have shown that it is possible to detect the presence of soliton-like classical configurations in many-particle systems from the nature of the one-point function and non-conservation of momentum feature of one-point, two-point and three-point functions in this low-energy effective field theory of these excitations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

Enhanced pool boiling heat transfer with metal foam tubes in inline tube bundle configuration

Flooded evaporators, commonly known as shell-and-tube heat exchangers, are widely used in large-scale industrial refrigeration and air-conditioning systems due to their high pool boiling heat transfer efficiency. However, their bulky configuration requires a large refrigerant inventory, which poses safety challenges—particularly when employing next-generation A2L refrigerants that are mildly flammable. Here, to address this issue, the development of compact heat exchangers with enhanced heat transfer performance is essential. In this study, a novel metal foam tube design is proposed to augment pool boiling heat transfer. Experiments were conducted at a saturation temperature of 20 °C and across a heat flux range of 7–60 kW m −2 . The tests were conducted for both smooth and metal foam tubes with an inline tube bundle configuration and for a pitch–to–diameter (P/D) ratios of 1.3 and 1.5. Pool boiling performance was evaluated for next-generation hydrofluoroolefin (HFO) refrigerants, R1234yf and R1234ze(E), with R134a serving as the baseline fluid. The results indicate that the heat transfer coefficient (HTC) of R1234yf is comparable to R134a, while R1234ze(E) shows slightly lower performance. Importantly, the metal foam tubes achieved up to a 217% enhancement in HTC compared to smooth tubes.

Metal foam tubes↗
DOE OSTI2025

Techno-economic evaluation of emission control configurations for AMP/PZ-based post-combustion CO 2 capture

Minimizing the environmental impacts of amine-based post-combustion carbon capture technologies is essential for regulatory compliance and public acceptance. Experimental campaigns at RWE's CO 2 capture pilot plant in Niederaussem using CESAR1 demonstrated that combining existing emission abatement technologies can substantially reduce the concentration of amines and degradation products in the CO 2 -depleted flue gas to below the detection limit of an infrared spectrometer. The campaign confirmed that a proprietary dry bed technology (OEASE aerozone™) or a second water wash can reduce AMP and PZ emissions to below 1 mg/Nm 3 . However, an acid or chemically active wash downstream of the water wash is necessary to reduce NH 3 emissions to very low levels (<2 mg/Nm 3 ). Combining a dry bed with an acid wash significantly reduces both the required acid solution and the resulting acid waste. The techno-economic analysis indicates that implementing emission mitigation technologies provides substantial environmental benefits for the CESAR1 process, with only a marginal increase (<1 €/tCO 2 ) in both the carbon capture cost (CCC) and CO 2 avoidance cost (CAC). The additional capital cost associated with extra column packing is offset by operational cost savings from reduced solvent losses. For stringent emission permits targeting NH 3 , a configuration combining a dry bed upstream of the water wash followed by an acid wash achieves the best balance between emission control and cost efficiency. This configuration results in a Levelized Cost of Electricity (LCOE) of 143 €/MWh, a CCC of 45.4 €/tCO 2 , and a CAC of 88.4 €/tCO 2 .

AMP↗
DOE OSTI2023

Balanced Fast-SpaciMS capillary configurations provide practically noninvasive channel-average measurements in catalytic monoliths

Spatially resolved capillary-inlet mass spectrometry (SpaciMS) provides a detailed picture of the spatiotemporal evolution of reaction network in catalytic monoliths. In the present work, we combine the SpaciMS experiments with a newly developed non-isothermal 3D CFD model for heterogeneously catalyzed reactive flows, including diffusion and permeation through the coated catalyst and channel wall. We explore how the capillary size and sampling rate can be balanced to minimize the impact on probed-channel conversions and provide species concentration measurements representative of the free channel average. In all studied configurations, the balanced sampling-rate fraction is noticeably higher than the corresponding capillary occlusion fraction. For a typical 350-micron capillary that occupies 11% of the channel cross- section, the balanced sampling rate represents 43% of the channel flow. Furthermore, the present work shows that together, a balanced SpaciMS configuration and numerical simulation provide accurate channel-averaged information of a monolithic catalyst under realistic operation conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A New Simple-to-Configure Self-Perturbing Multivariable Extremum-Seeking Controller

This paper presents a new stochastic relay-based extremum-seeking controller (ESC) for multi-input-single-output (MISO) systems. The algorithm was developed with the goal of simplifying configuration to enable easier deployment to real-world problems. A solution is developed first for a static map and then adapted for a general class of dynamic systems. The number of configurable parameters is one per input channel for the static case and only one additional parameter is needed for the dynamic version. The problem of gradient identifiability is solved via the use of stochastic relay gains and a simple stability proof for the static case is presented. Simulation tests demonstrate the performance of the strategy for optimizing both static and dynamic systems.

Salsbury, Timothy [BATTELLE (PACIFIC NW LAB)]↗
DOE OSTI2020

Performance analysis of hybrid power configurations: Impact on primary energy intensity, carbon dioxide emissions, and life cycle costs

In this work, utilization of Natural gas and Hydrogen to support current and future building energy needs to offset the total electric demand while improving the grid resiliency and energy efficiency was investigated. Demand side energy management will play an important role in efficiently managing the available energy resources. Performance assessment of different power generation and energy management configurations is presented in this paper. Development of solutions in addressing grid resiliency by providing the ability to design suitable configurations for meeting individual building energy needs is discussed. Primary movers (PM) such as internal combustion engines (ICE) and fuel cells (FC) along with small scale auxiliary renewable energy source such as photovoltaics (PV) were considered. Key attributes of total carbon foot-print, life cycle costs including capital and operational expenditure, electric grid offset or peak shaving capability, thermal energy availability and its further potential to offset total electric demand, and primary energy intensity are analyzed and discussed in detail.

08 HYDROGEN↗
DOE OSTI2021

Multi-objective optimization of low-GWP mixture composition and heat exchanger circuitry configuration for improved system performance and reduced refrigerant flammability

The recently introduced hydrofluoroolefin (HFO) refrigerants, including R1234yf and R1234ze(E), have significantly lower global warming potentials (GWPs) than traditional hydrofluorocarbon (HFC) refrigerants like R410A. However, prior tests show that direct drop-in of pure R1234yf or R1234ze(E) into equipment designed for R410A results in a decrease in heat exchanger capacity and the system coefficient of performance. The primary reason is the lower in-tube heat transfer performance of R1234yf and R1234ze(E) compared with that of R410A. To address this issue, previous studies have mixed the mildly flammable HFC R32 with HFOs to improve system performance, with HFC R125 also added to suppress flammability. Previous studies selected compositions based on simple cycle analyses and did not consider modifications of the heat exchanger circuitry configuration to adapt to the new refrigerants. This study presents a novel multi-objective optimization approach to design a refrigerant composition that maximizes energy efficiency within flammability and GWP limits. The approach in this work simultaneously optimizes mixture composition and heat exchanger circuitry configuration. A case study on a rooftop unit indicates that, compared with mixture-only optimization, simultaneous optimization of mixture and heat exchanger circuitry yields a 5.9% improvement in cycle efficiency and a 48.6% reduction in refrigerant flammability with a GWP of 268. Circuitry optimization using refrigerants with different temperature glides shows that the larger the temperature glide is, the larger EER improvement is obtained. The results show that zeotropic blends with a large temperature glide are more sensitive to the refrigerant circuitry than pure refrigerants and may suffer significant performance degradation with subpar heat exchanger circuitry design. The proposed optimization approach is generally applicable to mixtures with any number of components. Using this approach to design a HVAC system can yield higher system efficiency within flammability and GWP constraints.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Comparison of carrier localization effects between InAs quantum dashes and quantum dots in a DWELL (dashes- or dots-in-a-well) configuration

The optical properties of InAs quantum dashes (QDashes) grown on InP and InAs quantum dots (QDots) grown on GaAs in a dashes- or dots-in-a-well (DWELL) configuration are comparatively investigated using temperature-dependent photoluminescence (PL) measurements. The trends in PL characteristics such as exciton energy, spectral bandwidth and integrated intensity with respect to temperature are found to be distinctly dissimilar between the two systems. A rate-equation model involving exciton recombination and thermal transfer in a localized-state ensemble is used to quantitively interpret the experimental data. The results of this study suggest that QDashes in this configuration exhibit PL properties more consistent with a lower degree of carrier localization compared to QDots. A preliminary structural analysis highlighting the shape/size differences between the two nanostructures is also presented.

carrier localization↗
DOE OSTI2024

Optimizing the location and configuration of disaster resilience hubs under transportation and electric power network failures

Natural disasters often result in failures of transportation network components and blackouts that imperil the wellbeing of vulnerable populations. In response to these events, resilience hubs have been proposed as a pre-disaster planning strategy to improve access to critical services. This paper introduces an optimization-based approach to locate and configure electric power-generating resilience hubs considering the possibility of failures in transportation and electric power systems. The model's objective is to identify hub locations and configurations that maximize transportation accessibility to the hubs and maximize the satisfaction of basic energy needs through hub-generated electric power. Besides a budget constraint, the model accounts for limits on the levels of hub energy generation vis-à-vis community energy demands, and on the transportation network distance of communities to hubs. Three heuristics are presented for the proposed planning problem. The first heuristic is a genetic algorithm (GA) with problem-specific solution generation procedures. The other two heuristics implement greedy search techniques. Numerical experiments were conducted, using data from rural Puerto Rico, to illustrate the application of the proposed model and heuristics, and examine their performance. In the numerical experiments, the GA heuristic found better solutions than the greedy heuristics. Additionally, design solutions consisting of spatially dispersed hubs with low energy generation capacity were better than solutions with spatially concentrated high-capacity hubs. Lastly, across a wide range of hub demand scenarios, only a small number of candidate hub locations consistently ranked among the best locations for establishing a hub.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Expanding Configurational Complexity through Dipole Dilution in Pseudohalide Argyrodite Ion Conductors

The advantageous properties of (pseudo)halide argyrodite ion conductors of the formula Li 6 PS 5 X (X = Cl – , Br – , I – , CN – ) have motivated extensive studies of their structure-transport relationships, particularly as they pertain to the role of atomic site disorder. The argyrodite structure can accommodate additional configurational complexity to promote ion transport via extended three-anion site mixing and the potential for orientational disorder of molecular anions. In this work, we explore a ternary anion system including the cyanide anion, expanding site disorder and introducing dipolar orientations as an additional degree of freedom. We prepared the series Li 6 PS 5 (CN) 1–x Br x , in which the dipolar cyanide anions are systematically diluted with bromide. We find that anion disorder, as determined by synchrotron and neutron diffraction and quantified by configurational entropy (S config ), is correlated with lowered activation barriers and increased lithium ion conductivity. We propose that S config describes the electrostatic heterogeneity of the Li environments, flattening the energetic landscape for ion transport. While anion substitution strongly impacts the activation barrier for transport, the temperature-independent Arrhenius prefactor does not follow the same trend. Through heat-capacity measurements of attempt frequency and deconvolution of terms within the prefactor, we rationalize the apparent decoupling of activation energy and prefactor to strong cyanide-lithium interactions that increase the entropy of migration. Together, these results expand the structure–property relationships in the argyrodite family to encompass multiple facets of disorder and the subsequent impact on lithium ion transport.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗