SEARCH · Search NASA

Results for “Distributed temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

All sources NASA NTRS DOE OSTI

NASA NTRS2012

Measurement of Two-Phase Flow and Heat Transfer Parameters using Infrared Thermometry

A novel technique to measure heat transfer and liquid film thickness distributions over relatively large areas for two-phase flow and heat transfer phenomena using infrared (IR)thermometry is described. IR thermometry is an established technology that can be used to measure temperatures when optical access to the surface is available in the wavelengths of interest. In this work, a midwave IR camera (3.6-5.1 microns) is used to determine the temperature distribution within a multilayer consisting of a silicon substrate coated with a thin insulator. Since silicon is largely transparent to IR radiation, the temperature of the inner and outer walls of the multilayer can be measured by coating selected areas with a thin, IR opaque film. If the fluid used is also partially transparent to IR, the flow can be visualized and the liquid film thickness can be measured. The theoretical basis for the technique is given along with a description of the test apparatus and data reduction procedure. The technique is demonstrated by determining the heat transfer coefficient distributions produced by droplet evaporation and flow boiling heat transfer.

Kim, Tae-Hoon↗

NASA NTRS2000

Heavy Element Abundances in NGC 5846

In this paper we analyze the diffuse X-ray coronae surrounding the elliptical galaxy NGC 5846, combining measurements from two observatories, ROSAT and the Advanced Satellite for Cosmology and Astrophysics. We map the gas temperature distribution and find a central cool region within an approximately isothermal gas halo extending to a radius of about 50 kpc and evidence for a temperature decrease at larger radii. With a radially falling temperature profile, the total mass converges to (9.6 +/- 1.0) x 10(exp 12) solar mass at 230 kpc radius. This corresponds to a total mass to blue light ratio of 53 +/- 5 solar mass/solar luminosity. As in other early type galaxies, the gas mass is only a few percent of the total mass. Using the spectroscopic measurements, we also derive radial distributions for the heavy elements silicon and iron and find that the abundances of both decrease with galaxy radius. The mass ratio of Si to Fe lies between the theoretical predictions for element production in SN Ia and SN II, suggesting an important role for SN Ia, as well as SN II, for gas enrichment in ellipticals. Using the 2 SN la yield of Si, we set an upper limit of 0.012 h(sup 2, sub 50) solar neutrino units (SNU) for the SN Ia rate at radii >50 kpc, which is independent of possible uncertainties in the iron L-shell modeling. We compare our observations with the theoretical predictions for the chemical evolution of ellipticals. We conclude that the metal content in stars, if explained by the star formation duration, requires a significant decline in the duration of star formation with galaxy radius, ranging from 1 Gyr at the center to 0.01 Gyr at 100 kpc radius. Alternatively, the decline in metallicity with galaxy radius may be caused by a similar drop with radius in the efficiency of star formation. Based on the Si and Fe measurements presented in this paper, we conclude that the latter scenario is preferred unless a dependence of the SN Ia rate on stellar metallicity is invoked.

Jones, Christine↗

DOE OSTI2019

Thermal analysis of high-pressure hydrogen during the discharging process

The transient temperature and pressure of hydrogen are measured during the hydrogen discharging process through an orifice in a high-pressure vessel. The initial pressures of hydrogen in the vessel are set to approximately 30, 60, and 100 MPa. The mass flow rate and heat flux between hydrogen and the inner wall of the vessel are theoretically estimated using fundamental equations and experimental results with accurate thermophysical properties of hydrogen. The generation of temperature distribution and flow due to heat transfer in the vessel during discharge is verified by numerical analysis. Further, the relationship between reference gas temperature and heat flux in the vessel during the release of high-pressure hydrogen is studied. The average heat flux in the vessel is calculated using experimental and numerical analysis. The appropriate reference temperature is obtained using the comparison of the average heat flux in the vessel. In addition, the dominant heat transfer mode during hydrogen discharge is investigated. Numerical analysis shows that natural convection is formed inside the vessel due to a decrease in temperature. The Nusselt numbers in this process are presented as a function of Rayleigh numbers which are obtained by the experimental results and mass and energy conservations. The relationship between the Nusselt and Rayleigh numbers agrees with the heat transfer correlations of natural convections.

08 HYDROGEN↗

DOE OSTI2020

Magnetic field impact on the laser heating in MagLIF

Prior to implosion in Magnetized Liner Inertial Fusion (MagLIF), the fuel is heated to temperatures on the order of several hundred eV with a multi-kJ, multi-ns laser pulse. In this paper, we present two laser heated plasma experiments, relevant to the MagLIF preheat stage, performed at Z with beryllium liners filled with deuterium and a trace amount of argon. In one experiment, there is no magnetic field and, in the other, the liner and fuel are magnetized with an 8.5 T axial magnetic field. The recorded time integrated, spatially resolved spectra of the Ar K-shell emission are sensitive to electron temperature T e . Individual analysis of the spatially resolved spectra produces electron temperature distributions T e (z) that are resolved along the axis of laser propagation. In the experiment with magnetic field, the plasma reaches higher temperatures and the heated region extends deeper within the liner than in the unmagnetized case. Radiation magnetohydrodynamics simulations of the experiments are presented and post-processed. A comparison of the results from experimental and simulated data reveals that the simulations underpredict T e in both cases but the differences are larger in the case with magnetic field.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Three-dimensional reconstruction of inertial confinement fusion hot-spot plasma from x-ray and nuclear diagnostics on OMEGA

Multidimensional effects degrade the neutron yield and the compressed areal density of laser-direct-drive inertial confinement fusion implosions of layered deuterium–tritium cryogenic targets on the OMEGA Laser System with respect to 1D radiation-hydrodynamic simulation predictions. A comprehensive physics-informed 3D reconstruction effort is under way to infer hot-spot and shell conditions at stagnation from four x-ray and seven neutron detectors distributed around the OMEGA target chamber. Neutron diagnostics, providing measurements of the neutron yield, hot-spot flow velocity, and apparent ion-temperature distribution, are used to infer the mode-1 perturbation at stagnation. The x-ray imagers record the shape of the hot-spot plasma to diagnose mode-1 and mode-2 perturbations. A deep-learning convolutional neural network trained on an extensive set of 3D radiation-hydrodynamic simulations is used to interpret the x-ray and nuclear measurements to infer the 3D profiles of the hot-spot plasma conditions and the amount of laser energy coupled to the hot-spot plasma. A 3D simulation database shows that larger mode-1 asymmetries are correlated with higher hot-spot flow velocities and reduced laser-energy coupling and neutron yield. Three-dimensional hot-spot reconstructions from x-ray measurements indicate that higher amounts of residual kinetic energy are correlated with higher measured hot-spot flow velocities, consistent with 3D simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Simultaneous inference of plate boundary stresses and mantle rheology using adjoints: large-scale 2-D models

SUMMARY Plate motions are a primary surface constraint on plate and mantle dynamics and rheology, plate boundary stresses and the occurrence of great earthquakes. Within an optimization method, we use plate motion data to better constrain uncertain mantle parameters. For the optimization problem characterizing the maximum a posteriori rheological parameters we derive gradients using adjoints and expressions to approximate the posterior distributions for stresses within plate boundaries. We apply these methods to a 2-D cross section from the western to eastern Pacific, with temperature distributions and fault zone geometries developed primarily from seismic and plate motion data. We find that the best-fitting stress exponent, n, is about 2.8 and the yield stress about 100 MPa or less. The normal stress on the interplate fault zones is about 100 MPa and the shear stresses about 10 MPa or less.

Rudi, Johann (ORCID:0000000265639265)↗

DOE OSTI2018

HTTR 3 D Cross Section Generation with Serpent and MAMMOTH

The High Temperature Test Reactor (HTTR) is a graphite moderated thermal reactor with a nominal power output of 30 MWth. The purpose of this work is to prepare a set of neutron cross sections for use in the transient analyses of three Loss of Forced Cooling (LOFC) events planned for this reactor. The cross sections are generated with the Serpent 2 3 D Monte Carlo code to include the axial heterogeneity and the strong axial coupling of this core. The approach yields good agreement of results when compared to previously used 2 D lattice models, which require a fine spatial discretization and, surprisingly, comes at a higher computational cost. In addition, the temperature distribution must be considered to obtain reasonable cross sections and the axial leakage component dominates the spectral effects in the core. Consequently, a temperature model as a function of the fuel and moderator temperatures is adopted, and the core is depleted to 390 effective full-power days (EFPDs). A full tabulation of cross sections is prepared at this burnup point for a variety of fuel and moderator temperatures. Next, the multiphysics reactor application MAMMOTH is used to evaluate the quality of these cross sections using a diffusion solver. As expected, the homogenization error in the cross sections is significant and the Super Homogenization (SPH) correction from MAMMOTH is necessary to preserve key reaction rates. The SPH corrected MAMMOTH results are in excellent agreement with the Serpent results and reproduce both the reference power profile and temperature coefficients at each tabulation point. This fact confirms the accuracy of the SPH corrected cross sections and demonstrates the maturity of using Serpent 2 and MAMMOTH for 3 D cross section generation, even for reactors as complex as the HTTR. Finally, the authors recommend that the cross sections should be parametrized with the local burnup and that a full core burnup calculation with coupled thermal fluids would provide a better estimate of the initial condition for any subsequent transient analysis. Unfortunately, this was not within the scope of this work, and direct analysis with these tabulations should be considered as a first order approximation, at best.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1977

Performance of large-bore tapered-roller bearings under combined radial and thrust load at shaft speeds to 15,000 rpm

The performance of 120.65-mm bore tapered roller bearings was investigated at shaft speeds up to 15,000 rpm. Temperature distribution and bearing heat generation were determined as a function of shaft speed, radial and thrust loads, lubricant flow rate, and lubricant inlet temperature. Lubricant was supplied by either jets or by a combination of holes through the cone directly to the cone-rib contact and jets at the roller small-end side. Cone-rib lubrication significantly improved high-speed tapered-roller bearing performance, yielding lower cone-face temperatures and lower power loss and allowing lower lubricant flow rates for a given speed condition. Bearing temperatures increased with increased shaft speed and decreased with increased lubricant flow rate. Bearing power loss increased with increased shaft speed and increased lubricant flow rate.

Parker, R. J.↗

NASA NTRS1977

Lubrication of high-speed, large bore tapered-roller bearings

The performance of 120.65-mm- (4.75-in.-) bore tapered-roller bearings was investigated at shaft speeds up to 15,000 rpm (18,000 DN). Temperature distribution and bearing heat generation were determined as a function of shaft speed, radial and thrust loads, lubricant flow rate, and lubricant inlet temperature. Lubricant was supplied either by jets or by a combination of holes through the cone directly to the cone-rib contact and jets at the roller small-end side. Cone-rib lubrication significantly improved high-speed tapered-roller bearing performance, yielding lower cone-face temperatures and lower power loss and allowing lower lubricant flow rates for a given speed condition. Bearing temperatures increased with increased shaft speed and decreased with increased lubricant flow rate. Bearing power loss increased with increased shaft speed and increased lubricant flow rate.

Parker, R. J.↗

NASA NTRS1978

Lubrication of high-speed, large bore tapered-roller bearings

The performance of 120.65-mm bore tapered-roller bearings was investigated at shaft speeds up to 15,000 rpm. Temperature distribution and bearing heat generation were determined as a function of shaft speed, radial and thrust loads, lubricant flow rate, and lubricant inlet temperature. Lubricant was supplied either by jets or by a combination of holes through the cone directly to the cone-rib contact and jets at the roller small-end side. Cone-rib lubrication significantly improved high-speed tapered-roller bearing performance, yielding lower cone-face temperatures and lower power loss and allowing lower lubricant flow rates for a given speed condition. Bearing temperatures increased with increased shaft speed and decreased with increased lubricant flow rate. Bearing power loss increased with increased shaft speed and increased lubricant flow rate.

Parker, R. J.↗

NASA NTRS1979

Crystallization, flow and thermal histories of lunar and terrestrial compositions

Contents: a kinetic treatment of glass formation; effects of nucleating heterogeneities on glass formation; glass formation under continuous cooling conditions; crystallization statistics; kinetics of crystal nucleation; diffusion controlled crystal growth; crystallization of lunar compositions; crystallization between solidus and liquidus; crystallization on reheating a glass; temperature distributions during crystallization; crystallization of anorthite and anorthite-albite compositions; effect of oxidation state on viscosity; diffusive creep and viscous flow; high temperature flow behavior of glass-forming liquids, a free volume interpretation; viscous flow behavior of lunar compositions; thermal history of orange soil material; breccias formation by viscous sintering; viscous sintering; thermal histories of breccias; solute partitioning and thermal history of lunar rocks; heat flow in impact melts; and thermal histories of olivines.

Uhlmann, D. R.↗

NASA NTRS1980

Performance of computer-optimized tapered-roller bearings to 2.4 million DN

The performance of 120.65 mm bore high speed design tapered roller bearings was investigated at shaft speeds to 20,000 rpm under combined thrust and radial load. The test bearing design was computer optimized for high speed operation. Temperature distribution and bearing heat generation were determined as a function of shaft speed, radial and thrust loads, lubricant flow rates, and lubricant inlet temperature. The roller bearing operated successfully at shaft speeds up to 20,000 rpm under heavy thrust and radial loads. Cup cooling was effective in decreasing the high cup temperatures to levels equal to the cone temperature.

Parker, R. J.↗

NASA NTRS1983

Reduction methods for nonlinear steady-state thermal analysis

Hybrid analysis techniques and a problem adaptive computational algorithm are presented for predicting the nonlinear steady state temperature distribution in structures and solids. In the proposed techniques, the structure is discretized by using the finite element method. The vector of nodal temperatures is then expressed as a linear combination of a small number of global temperature modes (or basis vectors), and the Bubnov Galerkin technique is used to compute the amplitudes of the global modes. The global temperature modes (or basis vectors) are chosen to include the various order derivatives of the nodal temperature vector with respect to preselected path parameter(s). The potential of the proposed reduction methods for solution of large scale, nonlinear thermal problems is discussed and the effectiveness of the methods is demonstrated by means of numerical examples, including steady state conduction, convection, and radiation modes of heat transfer.

Noor, A. K.↗

NASA NTRS1984

Qualification of the T2 wind tunnel in cryogenic operation. A: Thermal field, preliminary study of a schematic model

The T2 wind tunnel is described. The process of generating a cyrogenic gust using the example of a test made at very low temperature is presented. Detailed results of tests on temperatures for flow in the settling chamber, the interior walls of the system, and the metal casing are given. The transverse temperature distribution in the settling chamber and working section, and of the thermal gradients in the walls, are given as a function of the temperature level of the test.

Dor, J. B.↗

NASA NTRS1985

Temperatures within comet nuclei

Knowledge of the temperature distribution within comet nuclei is critical to the understanding of the state and behavior of comets. The present study is concerned with the temperature profile below the surface of the nucleus and below any dust mantle which may be present. With respect to the physics, the considered model is in some respects similar to that discussed by Weissman and Kiefer (1981, 1984). However, the new model is improved in various respects. It represents the first attempt to investigate directly the detailed nature of thermal profiles within a comet nucleus. Included in the investigation are calculations which consider the effects of variations in latitude, nucleus spin axis orientation, surface albedo, and thermal emissivity. It is shown that the application of the model, together with in situ measurements of temperatures within a cometary nucleus, could significantly constrain the range of possible subsurface physical properties.

Squyres, S. W.↗

NASA NTRS2012

Climate Change: A New Metric to Measure Changes in the Frequency of Extreme Temperatures using Record Data

Consensus on global warming is the result of multiple and varying lines of evidence, and one key ramification is the increase in frequency of extreme climate events including record high temperatures. Here we develop a metric- called "record equivalent draws" (RED)-based on record high (low) temperature observations, and show that changes in RED approximate changes in the likelihood of extreme high (low) temperatures. Since we also show that this metric is independent of the specifics of the underlying temperature distributions, RED estimates can be aggregated across different climates to provide a genuinely global assessment of climate change. Using data on monthly average temperatures across the global landmass we find that the frequency of extreme high temperatures increased 10-fold between the first three decades of the last century (1900-1929) and the most recent decade (1999-2008). A more disaggregated analysis shows that the increase in frequency of extreme high temperatures is greater in the tropics than in higher latitudes, a pattern that is not indicated by changes in mean temperature. Our RED estimates also suggest concurrent increases in the frequency of both extreme high and extreme low temperatures during 2002-2008, a period when we observe a plateauing of global mean temperature. Using daily extreme temperature observations, we find that the frequency of extreme high temperatures is greater in the daily minimum temperature time-series compared to the daily maximum temperature time-series. There is no such observable difference in the frequency of extreme low temperatures between the daily minimum and daily maximum.

Munasinghe, L.↗

NASA NTRS1975

Prevention of thermal bending of multilayered beams and plates

By adding an extra layer to multilayer beams or plates of different isotropic materials, it is possible to prevent the thermal bending of these materials. With the proper selection of thermoelastic properties the curvature produced prior to this addition would be eliminated. Several numerical examples are presented for various temperature distributions. A simple experiment was conducted, involving the addition of a brass strip to a bimetallic strip made of aluminum and steel at room temperature. The trimetal strip was placed in a furnace and remained straight for varying temperatures.

Yang, J. C. S.↗

NASA NTRS1977

Web-dendritic growth

The effects of various machine design parameters on the growth of web dendritic silicon ribbon were investigated. Ribbons were grown up to lengths of one meter, with widths increasing linearly up to one cm at the point of termination of growth. Thermal data were collected and evaluated for actual seeding and growth with variations in parameters affecting heat loss. It was found that for suitable growth, the mechanical system should be very rigid and stable, and the tolerances and specifications of the quartz crucibles must be far tighter than normal quartz tolerances. The widening rates of the ribbons were found to be a function of the temperature gradient rather than the temperature differences alone. A twin spacing in the seed of 3 microns to 2 microns was found to be unfavorable for growth; whereas spacing of 0.9 microns to 2 microns and 8 microns to 2 microns were favorable. Thermal modeling studies of the effects of furnace design parameters on the temperature distributions in melt and the growth of the dendritic web ribbon showed that the pull rate of the ribbon is strongly dependent on the temperature of the top thermal shield, the spacing between this shield and the melt, and the thickness of the growing web.

Hilborn, R. B.↗