Search NASA⌕ Search

SEARCH · Search NASA

Results for “ENGINES - PERFORMANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Experimental Studies of Low-Load Limit in a Stoichiometric Micro-Pilot Diesel Natural Gas Engine

While operating at light loads, diesel pilot-ignited natural gas engines with lean premixed natural gas suffer from poor combustion efficiency and high methane emissions. This work investigates the limits of low-load operation for a micro-pilot diesel natural gas engine that uses a stoichiometric mixture to enable methane and nitrogen oxide emission control. By optimizing engine hardware, operating conditions, and injection strategies, this study focused on defining the lowest achievable load while maintaining a stoichiometric equivalence ratio and with acceptable combustion stability. A multi-cylinder diesel 6.7 L engine was converted to run natural gas premix with a maximum diesel micro-pilot contribution of 10%. With a base diesel compression ratio of 17.3:1, the intake manifold pressure limit was 80 kPa(absolute). At a reduced compression ratio of 15:1, this limit increased to 85 kPa, raising the minimum stable load. Retarding the combustion phasing, typically used in spark-ignition engines to achieve lower loads, was also tested but found to be limited by degraded diesel ignition at later timings. Reducing the pilot injection pressure improved combustion stability, as did increasing pilot quantity at the cost of lower substitution ratios. The lean operation further reduced load but increased NOx and hydrocarbon emissions. At loads below the practical dual-fuel limit, a transition to lean diesel operation will likely be required with corresponding implications for the aftertreatment system.

03 NATURAL GAS↗
DOE OSTI2021

Lorentz Symmetry Group, Retardation and Energy Transformations in a Relativistic Engine

In a previous paper, we have shown that Newton’s third law cannot strictly hold in a distributed system of which the different parts are at a finite distance from each other. This is due to the finite speed of signal propagation which cannot exceed the speed of light in vacuum, which in turn means that when summing the total force in the system the force does not add up to zero. This was demonstrated in a specific example of two current loops with time dependent currents, the above analysis led to suggestion of a relativistic engine. Since the system is effected by a total force for a finite period of time this means that the system acquires mechanical momentum and energy, the question then arises how can we accommodate the law of momentum and energy conservation. The subject of momentum conservation was discussed in a pervious paper, while preliminary results regarding energy conservation where discussed in some additional papers. Here we give a complete analysis of the exchange of energy between the mechanical part of the relativistic engine and the field part, the energy radiated from the relativistic engine is also discussed. We show that the relativistic engine effect on the energy is 4th-order in 1c and no lower order relativistic engine effect on the energy exists.

42 ENGINEERING↗
DOE OSTI2021

Demonstration of Better than Diesel Efficiency and Soot Emissions using Gasoline Compression Ignition in a Light Duty Engine with a Fuel Pressure Limitation

Increasing regulatory demand to reduce CO2 emissions has led to a focus on advanced combustion strategy development to improve overall engine efficiency. Gasoline compression ignition (GCI) has been demonstrated by others to have the potential to meet future CO2 regulations and emissions while achieving comparable to better efficiency than conventional diesel compression ignition (DCI). Soot and NOx emissions are also reduced significantly by using gasoline instead of diesel in compression ignition engines due to differences in composition, fuel properties, and reactivity. In comparison with diesel fuel, gasoline has a higher volatility and more resistance to autoignition, therefore, its longer ignition delay time will allow for better mixing of the air-fuel charge before combustion. In this study, a GCI combustion system has been tested in a Hyundai 2.2L engine as part of a US Department of Energy funded project. A double-injection strategy was tested from mid-to-high loads (5-20 bar BMEP) and for engine speeds in the range of 1200-3000 rpm. Up to 43.4% brake thermal efficiency was achieved using the GCI mode versus 41% using DCI mode. The GCI mode has demonstrated two distinct strategies that work at different load ranges, partially premixed compression ignition (PPCI) and mixing-controlled compression ignition (MCCI). Overall, this study shows that for similar engine-out NOx levels, GCI mode had higher brake thermal efficiency than DCI with lower fuel pressure and EGR required.

02 PETROLEUM↗
NASA NTRS1957

Free-jet Tests of a 1.1-inch-diameter Supersonic Ram-jet Engine

Results are presented of free-jet tests of a 1.1-inch-diameter hydrogen-burning ram-jet engine over a Mach number range from 1.42 to 2.28 and a Reynolds number range from 6.01 times 10 to the 6th power to 15.78 times 10 to the 6th power. Tests demonstrated the reliability and wide operating range of the engine and showed its suitability for installation on wind-tunnel models of airplane and missile configurations. A comparison of engine operation with combustion-chamber lengths of 3.33 and 1.51 engine diameters was made at a Mach number of 2.06. A maximum test thrust coefficient of 0.905 was obtained at fuel-air ratio of 0.034 and a Mach number of 2.06 for the engine with the 3.33-diameter combustion chamber.

ENGINES, RAM-JET↗
NASA NTRS2005

Introduction to Flight Test Engineering [Introduction Aux Techniques Des Essais En Vol]

Flight test is at the core of what organizations must do in order to validate the operation and systems on an aircraft. While the AGARDograph series 300 and 160 series deal with aspects of this testing, this volume pulls it all together as an introduction to the process required to do effective flight test engineering. This volume was originally published in 1995. Its utility has been proven in that many flight test organizations and universities have requested copies for their engineers and students. It was felt that re-issuing it in a new format designed for electronic publication would be valuable to the community. This second printing changes none of the text, but rather reformats it. All the original references to AGARD (instead of RTO) are left in place so that none of the flavor of the original publication is lost. This is the Introductory Volume to the Flight Test Techniques Series. It is a general introduction to the various activities and aspects of Flight Test Engineering that must be considered when planning, conducting, and reporting a flight test program. Its main intent is to provide a broad overview to the novice engineer or to other people who have a need to interface with specialists within the flight test community. The first two Sections provide some insight into the question of why flight test and give a short history of flight test engineering. Sections 3 through 10 deal with the preparation for flight testing. They provide guidance on the preliminary factors that must be considered; the composition of the test team; the logistic support requirements; the instrumentation and data processing requirements; the flight test plan; the associated preliminary ground tests; and last, but by no means least, discuss safety aspects. Sections 11 through 27 describe the various types of flight tests that are usually conducted during the development and certification of a new or modified aircraft type. Each Section offers a brief introduction to the topic under consideration, and the nature and the objectives of the tests to be conducted. It lists the test instrumentation (and, where appropriate, other test equipment and facilities) required, describes the test maneuvers to be executed, and indicates the way in which the test data is selected, analyzed, and presented. The various activities that should take place between test flights are presented next. Items that are covered are: who to debrief; what type of reports to send where: types of data analysis required for next flight; review of test data to make a comparison to predicted data and some courses of action if there is not good agreement; and comments on selecting the next test flight. The activities that must take place upon completion of the test program are presented. The types of reports and briefings that should take place and a discussion of some of the uses of the flight test data are covered. A brief forecast is presented of where present trends may be leading.

Test facilities↗
NASA NTRS2006

Zero to Integration in Eight Months, the Dawn Ground Data System Engineering Challange

The Dawn Project has presented the Ground Data System (GDS) with technical challenges driven by cost and schedule constraints commonly associated with National Aeronautics and Space Administration (NASA) Discovery Projects. The Dawn mission consists of a new and exciting Deep Space partnership among: the Jet Propulsion Laboratory (JPL), responsible for project management and flight operations; Orbital Sciences Corporation (OSC), spacecraft builder and responsible for flight system test and integration; and the University of California, at Los Angeles (UCLA), responsible for science planning and operations. As a cost-capped mission, one of Dawn s implementation strategies is to leverage from both flight and ground heritage. OSC's ground data system is used for flight system test and integration as part of the flight heritage strategy. Mission operations, however, are to be conducted with JPL s ground system. The system engineering challenge of dealing with two heterogeneous ground systems emerged immediately. During the first technical interchange meeting between the JPL s GDS Team and OSC's Flight Software Team, August 2003, the need to integrate the ground system with the flight software was brought to the table. This need was driven by the project s commitment to enable instrument engineering model integration in a spacecraft simulator environment, for both demonstration and risk mitigation purposes, by April 2004. This paper will describe the system engineering approach that was undertaken by JPL's GDS Team in order to meet the technical challenge within a non-negotiable eight-month schedule. Key to the success was adherence to an overall systems engineering process and fundamental systems engineering practices: decomposition of the project request into manageable requirements; definition of a structured yet flexible development process; integration of multiple ground disciplines and experts into a focused team effort; in-process risk management; and aggregation of the intermediate products to an integrated final product. In addition, this paper will highlight the role of lessons learned from the integration experience. The lessons learned from an early GDS deployment have served as the foundation for the design and implementation of the Dawn Ground Data System.

systems engineering↗
NASA NTRS2008

Enabling Innovation and Collaboration Across Geography and Culture: A Case Study of NASA's Systems Engineering Community of Practice

In 2004, NASA faced major knowledge sharing challenges due to geographically isolated field centers that inhibited personnel from sharing experiences and ideas. Mission failures and new directions for the agency demanded better collaborative tools. In addition, with the push to send astronauts back to the moon and to Mars, NASA recognized that systems engineering would have to improve across the agency. Of the ten field centers, seven had not built a spacecraft in over 30 years, and had lost systems engineering expertise. The Systems Engineering Community of Practice came together to capture the knowledge of its members using the suite of collaborative tools provided by the NASA Engineering Network (NEN.) The NEN provided a secure collaboration space for over 60 practitioners across the agency to assemble and review a NASA systems engineering handbook. Once the handbook was complete, they used the open community area to disseminate it. This case study explores both the technology and the social networking that made the community possible, describes technological approaches that facilitated rapid setup and low maintenance, provides best practices that other organizations could adopt, and discusses the vision for how this community will continue to collaborate across the field centers to benefit the agency as it continues exploring the solar system.

NEN↗
NASA NTRS2012

Concept Assessment of a Fission Fragment Rocket Engine (FFRE) Propelled Spacecraft

The March, 2012 issue of Aerospace America stated that ―the near-to-medium prospects for applying advanced propulsion to create a new era of space exploration are not very good. In the current world, we operate to the Moon by climbing aboard a Carnival Cruise Lines vessel (Saturn 5), sail from the harbor (liftoff) shedding whole decks of the ship (staging) along the way and, having reached the return leg of the journey, sink the ship (burnout) and return home in a lifeboat (Apollo capsule). Clearly this is an illogical way to travel, but forced on Explorers by today's propulsion technology. However, the article neglected to consider the one propulsion technology, using today's physical principles that offer continuous, substantial thrust at a theoretical specific impulse of 1,000,000 sec. This engine unequivocally can create a new era of space exploration that changes the way spacecraft operate. Today's space Explorers could travel in Cruise Liner fashion using the technology not considered by Aerospace America, the novel Dusty Plasma Fission Fragment Rocket Engine (FFRE). This NIAC study addresses the FFRE as well as its impact on Exploration Spacecraft design and operation. It uses common physics of the relativistic speed of fission fragments to produce thrust. It radiatively cools the fissioning dusty core and magnetically controls the fragments direction to practically implement previously patented, but unworkable designs. The spacecraft hosting this engine is no more complex nor more massive than the International Space Station (ISS) and would employ the successful ISS technology for assembly and check-out. The elements can be lifted in "chunks" by a Heavy Lift Launcher. This Exploration Spacecraft would require the resupply of small amounts of nuclear fuel for each journey and would be an in-space asset for decades just as any Cruise Liner on Earth. This study has synthesized versions of the FFRE, integrated one concept onto a host spacecraft designed for manned travel to Jupiter's moon, Callisto, and assessed that round trip journey. This engine, although unoptimized, produced 10 pounds force of thrust at a delivered specific impulse of 527,000 seconds for the entire 15-year mission while providing enormous amounts of electrical power to the spacecraft. A payload of 60 metric tons, included in the 300 metric ton vehicle, was carried to Callisto and back; the propellant tanks holding the 4 metric tons of fuel were not jettisoned in the process. The study concluded that the engine and spacecraft are within today's technology, could be built, tested, launched on several SLS (Space Launch System) (or similar) launchers, integrated, checked out, moved to an in-space base such as at a Lagrange point and operated for decades.

Engine↗
NASA NTRS2016

Improving Free-Piston Stirling Engine Power Density

Analyses and experiments demonstrate the potential benefits of optimizing piston and displacer motion in a free piston Stirling Engine. Isothermal analysis shows the theoretical limits of power density improvement due to ideal motion in ideal Stirling engines. More realistic models based on nodal analysis show that ideal piston and displacer waveforms are not optimal, often producing less power than engines that use sinusoidal piston and displacer motion. Constrained optimization using nodal analysis predicts that Stirling engine power density can be increased by as much as 58% using optimized higher harmonic piston and displacer motion. An experiment is conducted in which an engine designed for sinusoidal motion is forced to operate with both second and third harmonics, resulting in a maximum piston power increase of 14%. Analytical predictions are compared to experimental data showing close agreement with indirect thermodynamic power calculations, but poor agreement with direct electrical power measurements.

Stirling engines↗
NASA NTRS2015

Simulation of Liquid Rocket Engine Failure Propagation Using Self-Evolving Scenarios

Traditional probabilistic risk assessment approaches often require failure scenarios to be explicitly defined through event sequences that are then quantified as part of the integrated analysis. This approach becomes difficult when failure propagation paths change as a function of the system operation. Additionally, if the propagation paths represent interactions among even a modest number of components, the scenario count becomes combinatorially intractable. This paper presents an alternate approach for quantifying the probability of failure propagation in such a case. Rather than explicitly defining scenario sequences, simple physical models are created for each of the components. In this way, only the physical states and rules of component interactions must be defined, rather than event sequences for each individual scenario. Initiating failures are introduced into the system, either randomly or as defined by relative likelihood, and the failures cascade through the system via the interaction rules. This process is repeated using Monte Carlo methods and, as a result, the most probable scenarios “self-evolve” in terms of both sequence path and frequency. This approach was applied to failures occurring in the engine compartment of a space launch vehicle with four liquid rocket engines and four high-pressure helium tanks. Each engine was modeled with key components, such as turbomachinery, combustion chamber, propellant lines, and additional support systems. Three test cases were conducted with different high-energy engine failures. End results of interest included an additional engine-out failure and tank burst, which represent the loss-of-mission (LOM) and loss-of-crew (LOC) failure environments, respectively. Observations show that almost every scenario outcome is unique and that many scenarios involve complex chain reactions that are difficult to predict. This validates the usefulness of the modeling approach in assessing the overall risks to the crew during a launch vehicle abort.

Rocket Engine↗
NASA NTRSDate not supplied

Systems Engineering Tutorial with Case Studies

Due to the ever-growing number of complex technical problems facing our world, a Systems Engineering approach is needed to assist in successful design, build and implementation of solutions. The interdisciplinary technical structure of current systems, technical processes representing System Design, Technical Management and Product Realization are instrumental in the development and integration of new technologies into mainstream applications. This tutorial will demonstrate the application of Systems Engineering tools to these types of problems. Learning objectives include, understanding how to develop and engineer a conceptual system; understand the importance of teams, communication, requirements definition, interface control, and focus on deliverables; useful tools and techniques for each aspect of the System Engineering process including Model Based Systems Engineering which will be touched upon lightly. Some hands-on problems will be pursued especially in requirements development which is always key to a successful project. Case studies will be presented to assist in the learning process.

Systems Engineering↗
NASA NTRS1993

Operating Characteristics of a 15-cm dia. Ion Engine for Small Planetary Spacecraft

A 15-cm diameter, scaled-down version of the NASA light-weight 30-cm ion engine has been developed for potential application to very small planetary spacecraft. Integration of the 15-cm ion source into 4x15-cm segmented engine configuration results in a 30-cm equivalent engine which can be throttled over a 7-to-1 input power variation with a constant beam current in each of the four segments. Throttling the segmented engine by turning off individual segments can result in a significant decrease in the required service life (and qualification requirements) of the ion source components.

grids segmented ion engine↗
DOE OSTI2025

Cyber-Informed Engineering Briefing for ABET

Cyber-Informed Engineering (CIE) is an emerging method to integrate cybersecurity considerations into the conception, design, development, and operation of any physical system, energy or otherwise, to mitigate or even eliminate avenues for cyber-enabled attacks.?CIE concepts use design decisions and engineering controls to prioritize defense against the worst possible consequences of cyberattacks facing critical infrastructure systems and asset owners. These slides offer a deep dive into Cyber-Informed Engineering for engineering educators.

42 - ENGINEERING↗
DOE OSTI2020

Autoignition behavior of gasoline/ethanol blends at engine-relevant conditions

Ethanol is an attractive oxygenate increasingly used for blending with petroleum-derived gasoline yielding beneficial combustion and emissions behavior for a range of internal combustion engine schemes, including stoichiometric spark-ignition and low temperature combustion (LTC). As such, it is important to fundamentally understand the autoignition behavior of gasoline/ethanol blends. This work utilizes a rapid compression machine (RCM) and a homogeneous charge compression ignition (HCCI) engine to experimentally quantify changes in fuel reactivity, through ignition delay times and preliminary heat release, for blends of 0 to 30% vol./vol. into a full boiling range research gasoline (FACE-F). Diluted/stoichiometric and undiluted/fuel-lean conditions are explored covering a wide range of compressed temperatures and pressures relevant to conventional and advanced, gasoline combustion engines. Detailed chemical kinetic modeling is undertaken using a recently updated gasoline surrogate model in conjunction with a five-component surrogate to model the RCM experiments and provide chemical insight into the perturbative effects of ethanol on the autoignition process. The diluted/stoichiometric RCM measurements reveal that within the low-temperature regime ethanol retards first-stage and main ignition delay times, and suppresses both the rates and extents of low-temperature heat release (LTHR), while within the intermediate-temperature regime ethanol only causes slight changes. Good agreement of ignition delay time and preliminary heat release prediction is found between model and experimental results. Sensitivity and flux analyses further show that ethanol blending effects are dominated by the competition between the H-atom abstraction from ethanol and other fuel components by OH radical at low temperatures and by HO 2 radical at intermediate temperatures. These findings are consistent across both fuel loading conditions explored in this study. In addition, when HCCI engine experiments are mapped onto undiluted/lean RCM measurements under a constant combustion phasing scenario, good correspondence between the two apparatuses is observed for LTHR and start of high-temperature heat release. Finally, the current study highlights the importance of characterizing LTHR in predicting fuel behaviors in high-boost/low-temperature engines, and demonstrates that RCM experiments can provide an alternative, and more-efficient avenue for such characterization.

02 PETROLEUM↗
DOE OSTI2022

Advances in engineering algae for biofuel production

While algae demonstrate potential as a sustainable fuel source, low productivities limit the economic realization of algal biofuels. High-throughput strain engineering, omics-informed genome-scale modeling, and microbiome engineering are key technologies for enabling algal biofuels. High-throughput strain engineering efforts generate improved traits, including high biomass productivity and lipid content, in diverse algal species. Genome-scale models, constructed with the aid of omics data, provide insight into metabolic limitations and guide rational algal strain engineering efforts. As outdoor cultivation systems introduce exogenous organisms, microbiome engineering seeks to eliminate harmful organisms and introduce beneficial species. In conclusion, optimizing algal biomass production and lipid content using these technologies may overcome the productivity barrier for the commercialization of algal biofuels.

09 BIOMASS FUELS↗
DOE OSTI2022

A FAIR-compliant parts catalogue for genome engineering and expression control in Saccharomyces cerevisiae

The synthetic biology toolkit for baker's yeast, Saccharomyces cerevisiae, includes extensive genome engineering toolkits and parts repositories. However, with the increasing complexity of engineering tasks and versatile applications of this model eukaryote, there is a continued interest to expand and diversify the rational engineering capabilities in this chassis by FAIR (findable, accessible, interoperable, and reproducible) compliance. In this study, we designed and characterised 41 synthetic guide RNA sequences to expand the CRISPR-based genome engineering capabilities for easy and efficient replacement of genomically encoded elements. Moreover, we characterize in high temporal resolution 20 native promoters and 18 terminators using fluorescein and LUDOX CL-X as references for GFP expression and OD600 measurements, respectively. Additionally, all data and reported analysis is provided in a publicly accessible jupyter notebook providing a tool for researchers with low-coding skills to further explore the generated data as well as a template for researchers to write their own scripts. We expect the data, parts, and databases associated with this study to support a FAIR-compliant resource for further advancing the engineering of yeasts.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Engineering Escherichia coli for selective 1-decanol production using the reverse β-oxidation (rBOX) pathway

1-Decanol has great value in the pharmaceutical and fragrance industries and plays an important role in the chemical industry. Here, in this study, we engineered Escherichia coli to selectively synthesize 1-decanol by using enzymes of the core reverse β-oxidation (rBOX) pathway and termination module with overlapping chain-length specificity. Through screening for acyl-CoA reductase termination enzymes and proper regulation of rBOX pathway expression, a 1-decanol titer of 1.4 g/L was achieved. Further improvements were realized by engineering pyruvate dissimilation to ensure the generation of NADH through pyruvate dehydrogenase (PDH) and reducing byproduct synthesis via a tailored YigI thioesterase knockout, increasing 1-decanol titer to 1.9 g/L. The engineered strain produced about 4.4 g/L 1-decanol with a yield of 0.21 g/g in 36 hours in a bi-phasic fermentation that used a dodecane overlay to increase 1-decanol transport and reduce its toxicity. Adjustment of pathway expression (varying inducer concentration) and cell growth (oxygen availability) enabled 1-decanol production at 6.1 g/L (0.26 g/g yield) and 10.05 g/L (0.2 g/g yield) using rich in shake flasks and bioreactor, respectively. Remarkably, the use of minimal medium resulted in 1-decanol production at 100% specificity at 2.8 g/L (0.14 g/g yield) and a per cell mass yield higher than rich medium. These 1-decanol titers, yields and purity are at least 10-fold higher than others reported to date and the engineered strain shows great potential for industrial production. Taken together, our findings suggest that using rBOX pathway and termination enzymes of proper chain-length specificity in combination with optimal chassis engineering should be an effective approach for the selective production of alcohols.

1-decanol↗
DOE OSTI2025

Using phage display for rational engineering of a higher-affinity humanized 3’ phosphohistidine-specific antibody

Abstract Histidine phosphorylation is a non-canonical post-translational modification (PTM), with 1-phosphohistidine (1-pHis) and 3-phosphohistidine (3-pHis) isoforms, that is understudied due to a lack of robust reagents, including high-affinity pHis-specific antibodies. Engineering pHis antibodies is challenging due to the labile nature of its phosphoramidate (P-N) bond. We developed a strategy for in vitro engineering of antibodies for the detection of native 3-pHis targets, in which the rabbit SC44-8 anti-3-pTza mAb is humanized into a scaffold (hSC44) that is suitable for phage display. Six unique Fab phage-displayed hSC44 scaffold libraries were screened for antibodies that bound 3-pHis with higher affinity and had specificity for 3-pHis versus 3-pTza. hSC44.20N32F L , the best engineered antibody, has ~10-fold higher affinity for 3-pHis than parental hSC44. Eleven new Fab structures, including the first antibody-pHis peptide structures, together with structural and quantum mechanical calculations, provided molecular insights into 3-pHis and 3-pTza discrimination by hSC44.20N32F L and the increased affinity obtained through engineering. We demonstrated the utility of these high-affinity 3-pHis-specific antibodies for the recognition of pHis proteins in mammalian cells by immunoblotting and immunofluorescence staining. Our work describes a general method for engineering labile PTM-specific antibodies and provides novel antibodies for investigating the role of 3-pHis in cell biology.

Martyn, Gregory D.↗