Search NASA⌕ Search

SEARCH · Search NASA

Results for “FREQUENCY DEPENDENCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Dielectric response of tantalum oxide subject to induced ion bombardment during oblique sputter deposition

We describe the deposition of insulating tantalum oxide thin films under conditions of controlled ion bombardment, which can be achieved using reactive sputtering on 90 deg. off-axis substrates with an applied substrate bias. Capacitive measurements of Ta{sub 2}O{sub 5} deposited on unbiased off-axis substrates indicate low frequency dielectric constants as high as epsilon{sub r}approx300. Low frequency loss tangents are high, tan delta>0.5, and have a pronounced frequency dependence. Deposition of the film off-axis with sufficient applied rf bias to the substrate (negative bias >-70 V) recovers the on-axis properties typical of Ta{sub 2}O{sub 5}, e.g., epsilon{sub r}approx22 and tan deltaapprox0.02. The recovery of normal dielectric behavior is attributed to the ion bombardment of the growing film under substrate bias, similar to on-axis depositions but absent from depositions on off-axis substrates with no applied substrate bias. We suggest that insufficiently bombarded films develop a Maxwell-Wagner type polarization along columnar voids. The void structure and the associated dielectric response vary with distance from the sputtering source due to variations in ion density and angle from the sputtering source. A similar dielectric response is observed in depositions on on-axis substrates as a function of angle from the central sputter gun axis. Our results suggest that ion bombardment is necessary for good quality sputtered dielectric films but that a controlled Ar{sup +} flux is essentially equivalent to the uncontrolled O{sub 2}{sup -}/O{sup 2-} flux of on-axis reactive sputtering.

36 MATERIALS SCIENCE↗

Static and dynamic polarizability for C{sup 2+} in Rydberg states

This work presents results from a non-perturbative calculation of dynamic polarizability of C III ions in 1s{sup 2}2sns ({sup 1}S{sup e}) Rydberg states. We employ a two-state model for dressed atomic states to investigate the effect of the frequency-dependent polarizability of optically dressed 1s{sup 2}2sns({sup 1}S{sup e}) states (n = 5 − 12) on transitions to nearby states (1s{sup 2}2pns({sup 1}P{sub 1}{sup o})). Our model calculation results indicate that the resonance structure of the polarizabilities is entirely captured by the transition terms whereas the free electron polarizability only provides a smooth background. The resonance structure is evident in the plots and the widths increase with increasing principal quantum number. This work refers to highly excited 1s{sup 2}2sns ({sup 1}S) Rydberg states, embedded in the electric dipole field of the 2s – 2p core transition in Li-like C{sup 3+} ion. The contributions of the individual transitions to the static polarizabilities of these Rydberg states are obtained from the use of the sum-over-state method. To this aim, both the C{sup 2+} ground state and the C{sup 3+} target state energies have been carefully calculated based on the configuration interactions method implemented in the General-purpose Relativistic Atomic Structure Package. Agreement is reasonably good with existing data wherever available. These results are believed to be the first such values for this system and will be important for ionic spectroscopy and plasma diagnostics.

74 ATOMIC AND MOLECULAR PHYSICS↗

BROADBAND RADIO POLARIMETRY AND FARADAY ROTATION OF 563 EXTRAGALACTIC RADIO SOURCES

We present a broadband spectropolarimetric survey of 563 discrete, mostly unresolved radio sources between 1.3 and 2.0 GHz using data taken with the Australia Telescope Compact Array. We have used rotation-measure synthesis to identify Faraday-complex polarized sources, those objects whose frequency-dependent polarization behavior indicates the presence of material possessing complicated magnetoionic structure along the line of sight (LOS). For sources classified as Faraday-complex, we have analyzed a number of their radio and multiwavelength properties to determine whether they differ from Faraday-simple polarized sources (sources for which LOS magnetoionic structures are comparatively simple) in these properties. We use this information to constrain the physical nature of the magnetoionic structures responsible for generating the observed complexity. We detect Faraday complexity in 12% of polarized sources at ∼1′ resolution, but we demonstrate that underlying signal-to-noise limitations mean the true percentage is likely to be significantly higher in the polarized radio source population. We find that the properties of Faraday-complex objects are diverse, but that complexity is most often associated with depolarization of extended radio sources possessing a relatively steep total intensity spectrum. We find an association between Faraday complexity and LOS structure in the Galactic interstellar medium (ISM) and claim that a significant proportion of the Faraday complexity we observe may be generated at interfaces of the ISM associated with ionization fronts near neutral hydrogen structures. Galaxy cluster environments and internally generated Faraday complexity provide possible alternative explanations in some cases.

79 ASTRONOMY AND ASTROPHYSICS↗

Quasiparticle and Optical Properties of Rutile and Anatase Ti2O2

Quasiparticle excitation energies and optical properties of TiO{sub 2} in the rutile and anatase structures are calculated using many-body perturbation-theory methods. Calculations are performed for a frozen crystal lattice; electron-phonon coupling is not explicitly considered. In the GW method, several approximations are compared and it is found that inclusion of the full frequency dependence as well as explicit treatment of the Ti semicore states are essential for accurate calculation of the quasiparticle energy-band gap. The calculated quasiparticle energies are in good agreement with available photoemission and inverse photoemission experiments. The results of the GW calculations, together with the calculated static screened Coulomb interaction, are utilized in the Bethe-Salpeter equation to calculate the dielectric function {epsilon}{sub 2}({omega}) for both the rutile and anatase structures. The results are in good agreement with experimental observations, particularly the onset of the main absorption features around 4 eV. For comparison to low-temperature optical-absorption measurements that resolve individual excitonic transitions in rutile, the low-lying discrete excitonic energy levels are calculated with electronic screening only. The lowest energy exciton found in the energy gap of rutile has a binding energy of 0.13 eV. In agreement with experiment, it is not dipole allowed but the calculated exciton energy exceeds that measured in absorption experiments by about 0.22 eV and the scale of the exciton binding energy is also too large. The quasiparticle energy alignment of rutile is calculated for nonpolar (110) surfaces. In the GW approximation, the valence-band maximum is 7.8 eV below the vacuum level, showing a small shift from density-functional theory results.

36 MATERIALS SCIENCE↗

Wireless Transmission of Monitoring Data out of the HADES Underground Laboratory - 12450

As part of the European 7. framework project MoDeRn, Nuclear Research and Consultancy Group (NRG) performed experiments in order to demonstrate the feasibility of wireless data transmission through the subsurface over larger distances by low frequency magnetic fields. The main objective of NRG's contribution is to characterize and optimize the energy use of this technique within the specific context of post-closure monitoring. For this, measurements have been performed in the HADES underground laboratory located at Mol, Belgium, at 225 m depth. The experimental set-up makes use of a loop antenna for the transmitter that has been matched into the existing infrastructure of the HADES. The experimental work of NRG is divided into several stages: in 2010, the necessary hardware has been designed and assembled and tested in the Netherlands. Site-specific magnetic background noise in Mol and frequency-dependent signal attenuation by the geologic medium has been measured. Signal transmission has been demonstrated and several transmission channels around 1 kHz have been identified. In 2011, additional measures and experiments have been performed in order to characterize and test relevant element of the transmission chain and to optimize the energy use of the set-up. A mathematical model description has been developed that includes the most relevant characteristics of the transmitter, receiver and transmission path and was used to analyse possible options to optimize the set-up. In 2012, experiments are planned in order to test several data transmission options. Results so far have shown that signal transmission over larger distances through the subsurface is feasible. However, to make quantitative conclusions on the energy need per bit of transmitted data, additional experiments planned in 2012 are necessary. The experimental and theoretical results gained by NRG, as part of the European 7. framework project MoDeRn, so far demonstrated that signal transmission through 225 m of a geological medium is feasible, even in case of a 'good conductor' as present in Mol. At this particular site the transmission distance through the different layers of clay and sandy aquifers is larger than the skin depth and clearly extends the near-field. The step from signal to data transmission will be made in 2012 and is essential to be able to make quantitative statements of the energy use per transmitted data bit. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

LOW-FREQUENCY OBSERVATIONS OF LINEARLY POLARIZED STRUCTURES IN THE INTERSTELLAR MEDIUM NEAR THE SOUTH GALACTIC POLE

We present deep polarimetric observations at 154 MHz with the Murchison Widefield Array (MWA), covering 625 deg{sup 2} centered on α = 0{sup h}and δ = −27°. The sensitivity available in our deep observations allows an in-band, frequency-dependent analysis of polarized structure for the first time at long wavelengths. Our analysis suggests that the polarized structures are dominated by intrinsic emission but may also have a foreground Faraday screen component. At these wavelengths, the compactness of the MWA baseline distribution provides excellent snapshot sensitivity to large-scale structure. The observations are sensitive to diffuse polarized emission at ∼54′ resolution with a sensitivity of 5.9 mJy beam{sup −1} and compact polarized sources at ∼2.′4 resolution with a sensitivity of 2.3 mJy beam{sup −1} for a subset (400 deg{sup 2}) of this field. The sensitivity allows the effect of ionospheric Faraday rotation to be spatially and temporally measured directly from the diffuse polarized background. Our observations reveal large-scale structures (∼1°–8° in extent) in linear polarization clearly detectable in ∼2 minute snapshots, which would remain undetectable by interferometers with minimum baseline lengths of >110 m at 154 MHz. The brightness temperature of these structures is on average 4 K in polarized intensity, peaking at 11 K. Rotation measure synthesis reveals that the structures have Faraday depths ranging from −2 to 10 rad m{sup −2} with a large fraction peaking at approximately +1 rad m{sup −2}. We estimate a distance of 51 ± 20 pc to the polarized emission based on measurements of the in-field pulsar J2330–2005. We detect four extragalactic linearly polarized point sources within the field in our compact source survey. Based on the known polarized source population at 1.4 GHz and non-detections at 154 MHz, we estimate an upper limit on the depolarization ratio of 0.08 from 1.4 GHz to 154 MHz.

79 ASTRONOMY AND ASTROPHYSICS↗

Self-consistent Kohn-Sham method based on the adiabatic-connection fluctuation-dissipation theorem and the exact-exchange kernel

A self-consistent Kohn-Sham method based on the adiabatic-connection fluctuation-dissipation (ACFD) theorem, employing the frequency-dependent exact exchange kernel f{sub x} is presented. The resulting SC-exact-exchange-only (EXX)-ACFD method leads to even more accurate correlation potentials than those obtained within the direct random phase approximation (dRPA). In contrast to dRPA methods, not only the Coulomb kernel but also the exact exchange kernel f{sub x} is taken into account in the EXX-ACFD correlation which results in a method that, unlike dRPA methods, is free of self-correlations, i.e., a method that treats exactly all one-electron systems, like, e.g., the hydrogen atom. The self-consistent evaluation of EXX-ACFD total energies improves the accuracy compared to EXX-ACFD total energies evaluated non-self-consistently with EXX or dRPA orbitals and eigenvalues. Reaction energies of a set of small molecules, for which highly accurate experimental reference data are available, are calculated and compared to quantum chemistry methods like Møller-Plesset perturbation theory of second order (MP2) or coupled cluster methods [CCSD, coupled cluster singles, doubles, and perturbative triples (CCSD(T))]. Moreover, we compare our methods to other ACFD variants like dRPA combined with perturbative corrections such as the second order screened exchange corrections or a renormalized singles correction. Similarly, the performance of our EXX-ACFD methods is investigated for the non-covalently bonded dimers of the S22 reference set and for potential energy curves of noble gas, water, and benzene dimers. The computational effort of the SC-EXX-ACFD method exhibits the same scaling of N{sup 5} with respect to the system size N as the non-self-consistent evaluation of only the EXX-ACFD correlation energy; however, the prefactor increases significantly. Reaction energies from the SC-EXX-ACFD method deviate quite little from EXX-ACFD energies obtained non-self-consistently with dRPA orbitals and eigenvalues, and the deviation reduces even further if the Coulomb kernel is scaled by a factor of 0.75 in the dRPA to reduce self-correlations in the dRPA correlation potential. For larger systems, such a non-self-consistent EXX-ACFD method is a competitive alternative to high-level wave-function-based methods, yielding higher accuracy than MP2 and CCSD methods while exhibiting a better scaling of the computational effort than CCSD or CCSD(T) methods. Moreover, EXX-ACFD methods were shown to be applicable in situation characterized by static correlation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrical properties of dispersions of graphene in mineral oil

Dispersions of graphene in mineral oil have been prepared and electrical conductivity and permittivity have been measured. The direct current (DC) conductivity of the dispersions depends on the surface characteristics of the graphene platelets and followed a percolation model with a percolation threshold ranging from 0.05 to 0.1 wt. %. The difference in DC conductivities can be attributed to different states of aggregation of the graphene platelets and to the inter-particle electron transfer, which is affected by the surface radicals. The frequency-dependent conductivity (σ(ω)) and permittivity (ε(ω)) were also measured. The conductivity of dispersions with particle contents much greater than the percolation threshold remains constant and equal to the DC conductivity at low frequencies ω with and followed a power-law σ(ω)∝ ω{sup s} dependence at very high frequencies with s≈0.9. For dispersions with graphene concentration near the percolation threshold, a third regime was displayed at intermediate frequencies indicative of interfacial polarization consistent with Maxwell-Wagner effect typically observed in mixtures of two (or more) phases with very distinct electrical and dielectric properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Magnetic field, frequency and temperature dependence of complex conductance of ultrathin La1.65Sr0.45CuO4/La2CuO4 films and the organic superconductors κ-(BEDT-TTF)2Cu[N(CN)2]Br

We used atomic-layer molecular beam epitaxy (ALL-MBE) to synthesize bilayer films of a cuprate metal (La1.65Sr0.45CuO4La1.65Sr0.45CuO4, LSCO) and a cuprate insulator (La2CuO4La2CuO4, LCO), in which interface superconductivity occurs in a layer that is just one-half unit cell thick. We have studied the magnetic field and temperature dependence of the complex sheet conductance, σ(ω)σ(ω), of these films, and compared them to κκ-(BEDT-TTF)2Cu[N(CN)2]Br2Cu[N(CN)2]Br single crystals. The magnetic field HH was applied both parallel and perpendicular to the 2D conducting layers. Experiments have been carried out at frequencies between 23 kHz and 50 MHz using either two-coil mutual inductance technique, or the LC resonators with spiral or rectangular coils. The real and the imaginary parts of the mutual-inductance M(T,ω)M(T,ω) between the coil and the sample were measured and converted to complex conductivity. For HH perpendicular to the conducting layers, we observed almost identical behavior in both films and κκ-Br single crystals: (i) the transition onset in the inductive response, L-1kLk-1(T) occurs at a temperature lower by 2 K than in Reσ(T)Reσ(T), (ii) this shift is almost constant with magnetic field up to 8 T; (iii) the vortex diffusion constant D(T)D(T) is exponential due to pinning of vortex cores. These results can be described by the extended dynamic theory of the Berezinski–Kosterlitz–Thouless (BKT) transition and dynamics of bound vortex–antivortex pairs with short separation lengths.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Accuracy of finite-difference harmonic frequencies in density functional theory

Analytic Hessians are often viewed as essential for the calculation of accurate harmonic frequencies, but the implementation of analytic second derivatives is nontrivial and solution of the requisite coupled-perturbed equations engenders a sizable memory footprint for large systems, given that these equations are not required for energy and gradient calculations in density functional theory. Here, we benchmark the alternative approach to harmonic frequencies based on finite differences of analytic first derivatives, a procedure that is amenable to large-scale parallelization. Not only for absolute frequencies but also for isotopic and conformer-dependent frequency shifts in flexible molecules, we find that the finite-difference approach exhibits mean errors < 0.1 cm -1 as compared to results based on an analytic Hessian. For very small frequencies corresponding to nonbonded vibrations in noncovalent complexes (for which the harmonic approximation is questionable anyway), the finite-difference error can be larger, but even in these cases the errors can be reduced below 0.1 cm -1 by judicious choice of the displacement step size and a higher-order finite-difference approach. Finally, the surprising accuracy and robustness of the finite-difference results suggests that availability of the analytic Hessian is not so important in today's era of commodity processors that are readily available in large numbers.

74 ATOMIC AND MOLECULAR PHYSICS↗

Systematically derived thermodynamic properties for alkane oxidation

Key combustion properties, such as ignition delay time, show strong sensitivity to the thermochemistry of the main species in the standard radical oxidation pathway at low temperatures (600-1000K). Significant uncertainties persist in current estimates of thermodynamic properties, particularly for the larger species of relevance to common practical fuels. In this article, we use advanced computational schemes to evaluate thermodynamic properties for the fuel, fuel radical, peroxy, hydroperoxy-alkyl radical, and hydroperoxide species for a set of 17 fuels containing up to 9 carbon atoms, and with various degrees of branching in the alkane backbone. The procedure, termed STAR-1D, combines conformer sampling to find the minimum geometry, B2PLYP-D3/cc-pVTZ harmonic frequency evaluations, and omega B97X-D/cc-pVTZ one-dimensional torsional mapping. It includes two physically-based scaling routines: a frequency-dependent scaling to B2PLYP-D3/cc-pVTZ anharmonic frequencies and a scaling of one-dimensional omega B97X-D/ccpVTZ torsional profiles to reproduce the product of the B2PLYP-D3/cc-pVTZ frequencies in the harmonic limit. Substantive comparisons with existing experimental databases, together with careful examinations of key theoretical assumptions, are used to explore the accuracy of the predictions. These computationally intensive explorations of 195 species were facilitated by automated thermochemistry software. Further, high accuracy 0 K heats of formation from a separate study are used with the STAR-1D computations to generate NASA polynomial representations. In addition to their intrinsic value, the present results also provide a reliable database for the optimization of group additivity or machine learning schemes for scaling to larger combustion systems. Towards this end a complementary extensive conformational analysis is carried out for the medium sized species and the thermodynamic properties of the lowest energy hydrogen-bonded and non-hydrogen bonded conformers are contrasted for larger hydroperoxy-alkyl radical species.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Split Hopkinson Resonant Bar Test for Sonic-Frequency Acoustic Velocity and Attenuation Measurements of Small, Isotropic Geologic Samples

Mechanical properties (seismic velocities and attenuation) of geological materials are often frequency dependent, which necessitates measurements of the properties at frequencies relevant to a problem at hand. Conventional acoustic resonant bar tests allow measuring seismic properties of rocks and sediments at sonic frequencies (several kilohertz) that are close to the frequencies employed for geophysical exploration of oil and gas resources. However, the tests require a long, slender sample, which is often difficult to obtain from the deep subsurface or from weak and fractured geological formations. In this paper, an alternative measurement technique to conventional resonant bar tests is presented. This technique uses only a small, jacketed rock or sediment core sample mediating a pair of long, metal extension bars with attached seismic source and receiver - the same geometry as the split Hopkinson pressure bar test for large-strain, dynamic impact experiments. Because of the length and mass added to the sample, the resonance frequency of the entire system can be lowered significantly, compared to the sample alone. The experiment can be conducted under elevated confining pressures up to tens of MPa and temperatures above 100 C, and concurrently with x-ray CT imaging. The described Split Hopkinson Resonant Bar (SHRB) test is applied in two steps. First, extension and torsion-mode resonance frequencies and attenuation of the entire system are measured. Next, numerical inversions for the complex Young's and shear moduli of the sample are performed. One particularly important step is the correction of the inverted Young's moduli for the effect of sample-rod interfaces. Examples of the application are given for homogeneous, isotropic polymer samples and a natural rock sample.

54 ENVIRONMENTAL SCIENCES↗

Development of a microwave capacitive method for the spectroscopy of the complex permittivity

We describe a vector network analyzer-based method to study the electromagnetic properties of nanoscale dielectrics at microwave frequencies (1 MHz–40 GHz). The complex permittivity spectrum of a given dielectric can be determined by placing it in a capacitor accessed on its both electrodes by coplanar waveguides. However, inherent propagation delays along the signal paths together with frequency-dependent effective surface of the capacitor at microwave frequencies can lead to significant distortion in the measured permittivity, which in turn can give rise to artificial frequency variations of the complex permittivity. We detail a fully analytical rigorous correction sequence with neither recourse to extrinsic loss mechanisms nor to arbitrary parasitic signal paths. We illustrate our method on 3 emblematic dielectrics: ferroelectric morphotropic lead zirconate titanate, its paraelectric pyrochlore counterpart, and strontium titanate. Permittivity spectra taken at various points along the hysteresis loop help shedding light onto the nature of the different dielectric energy loss mechanisms. Thanks to the analytical character of our method, we can discuss routes to extend it to higher frequencies and we can identify unambiguously the sources of potential artifacts.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Spin dynamics and relaxation in 7.6 nm thin film of La 0.7 Sr 0.3 MnO 3 /SrTiO 3 : ac magnetic susceptibility and magnetic viscosity investigations

Analysis of the results from our investigations of the temperature dependence of ac susceptibilities (χ' and χ'') and magnetic viscosity in a 7.6 nm thin film of La 0.7 Sr 0.3 MnO 3 grown on SrTiO 3 (001) substrate is presented. The Curie temperature (T C ) of this film is magnetic field (H) dependent, varying as [T C (H) - T C (0)] ~ H n with T C (0) = 270 K and n = 0.15. Temperature dependence of χ' and χ'' measured at ac frequencies f m in the range of 0.1–10 kHz shows a broad peak near 230 K associated with the blocking temperature (T B ) of spin clusters present in the 1.4 nm surface layer and a frequency dependent peak near 270 K associated with T C . The mean relaxation time τ determined from the Cole–Cole analysis of the temperature dependent χ' and χ'' is shown to fit the Vogel–Fulcher law: τ = τ 0 exp[ΔE/k B (T - T 0 )] with T 0 = 245 K, ΔE/k B = 270 K = T C and τ 0 = 1.2 x 10 -9 s. Magnetic viscosity S (measured in H = 0 for a sample cooled in H = 50 Oe) determined from the fit to the magnetization: M (t)= M (0) – S ln t, with time t up to 2 h, shows a peak at 230 K above which M (2 h) switches to negative values for temperatures up to T C (0). It is argued that this negative magnetization results from an interaction between the superparamagnetic spin clusters and the ferromagnetic phase, both being present in the temperature range of T B < T < T C .

36 MATERIALS SCIENCE↗

Spin glass dynamics at the mesoscale

The mesoscale provides a new probe of spin glass dynamics. Because the spin glass lower critical dimension d l > 2 , the growth of the correlation length ξ ( t , T ) can change the nature of the spin glass state at a crossover time t co when ξ ( t co , T ) = ℓ , a minimum characteristic sample length (e.g., film thickness for thin films and crystallite size for bulk samples). For thin films, and times t < t co such that ξ ( t , T ) < ℓ , conventional three-dimensional dynamics is observed. When t > t co , a crossover to d = 2 behavior takes place. The parallel correlation length, associated with a T g = 0 transition, increases in time from the saturated value of the perpendicular correlation length ℓ to an equilibrium value of the parallel correlation length proportional to T - ν . This results in a pancakelike correlated state, with a thickness ℓ and a temperature-dependent in-plane radius that increases with decreasing temperature. Activated dynamics is associated with these states. Measurements on Cu:Mn thin films are analyzed quantitatively within this framework. We extract a temperature-dependent activation energy from a fit to the frequency dependence of the dynamic susceptibility. The extrapolated temperature at which the activation energy would become large is close to the extrapolated glass transition temperature from ac susceptibility measurements. All known relevant experimental data are consistent with this method. For polycrystalline materials, there is a distribution of length scales P ( ℓ ) . For sufficiently broad distributions, a logarithmic time dependence is derived for the time decay of the thermoremanent magnetization M TRM ( t , T ) using an approach originally derived by Ma. Properties dependent upon an effective waiting time t w eff are derived that are consistent with experiment, and additional measurements are suggested.

36 MATERIALS SCIENCE↗

Fast-ion-driven Alfvén eigenmodes during ICRF-heated high β p plasmas on EAST

Fast-ion-driven Alfvén eigenmodes (AEs) are observed during ICRF-heated high-β p plasmas on EAST. Multiple high frequency modes are observed for shot 112670 at f TAE1 ~ 145 kHz, δB/B ~ 4 × 10 –4 and f TAE2 ~ 175 kHz, δB/B ~ 1.2 × 10 –5 measured by high-frequency Mirnov coils, at B 0 ~ 2.45 T, I p ~ 350kA, n e ramp-up from 3.5 × 10 19 to 4 × 10 19 m −3 at P ECRH ~ 2 MW, PLHW ~ 2 MW, and P ICRH ~ 2.1 MW. Here, 37 MHz ICRF minority hydrogen heating scheme, located at plasma core, creates fast ion population which drives TAEs unstable from TORIC + SFFPQL. In the experiment, it is observed that the evolution of mode frequency depends on electron density, following the theoretical TAE frequency characteristic $f_{{{\text{th}}}} = V_{{\text{a}}} /(4\pi qR) \propto \sqrt {n_{{\text{e}}} }$. As the electron density increases, the amplitude of the AE mode progressively diminishes. Higher plasma density shortens the fast-ion slowing-down time, reduces the heating efficiency of minority hydrogen, weakens the high-energy tail, and consequently decreases the fast-ion beta. Based on the diagnostic results from the microwave reflectometer and electron cyclotron emission (ECE) diagnostics, the TAE is located within the plasma core, consistent with the narrower core region of the TAE gap observed in the continuous spectrum.

Pan, C. Y. [Chinese Academy of Sciences, Hefei (Ch↗

Wideband electronics for ultrasonic tissue characterization

System utilizing natural ringing frequency of electronic circuit coupled to wideband transducer is used to determine frequency dependence of ultrasonic properties of tissue. With procedure frequency data can be obtained rapidly and inexpensively.

Gammell, P.↗

Nondestructive evaluation techniques for nickel-cadmium aerospace battery cells

The ac impedance characteristics of Ni-Cd cells as an in-situ, nondestructive means of determining cell lifetime, particularly with respect to the probability of premature failure were evaluated. Emphasis was on evaluating Ni-Cd cell impedance over a wide frequency range (10,000 to 0.0004 Hz) as the cells were subjected to charge/discharge cycle testing. The results indicate that cell degradation is reflected in the low frequency (Warburg) impedance characteristics associated with diffusion processes. The Warburg slope (W) was found to steadily increase as a function of cell aging for completely discharged cells. In addition, based on data for two cells, a high or rapidly increasing value for W signals imminent cell failure by one mechanism. Degradation by another mechanism is apparently reflected in a fall-off (roll-over) of W at lower frequencies. As a secondary result, the frequency dependence of the absolute cell impedance at low frequencies (5 - 500 mHz) was found to be a good indication of the cell state-of-charge.

Haak, R.↗