Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain microstructure evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Effect of Mg-Bearing Oxide(+TiN) Inclusion on Microstructure of Fe-16 Mass Pct Cr Ferritic Alloy and Its Evolution During Heating at 1573 K (1300 °C)

Both the effects of Mg-bearing oxide and Mg-bearing oxide +TiN inclusions on the microstructures of Fe-16 mass pct Cr alloy should be clarified. In this paper, the effects of Mg-bearing oxide(+TiN) inclusions on the microstructures of Fe-16 mass pct Cr ferritic alloy and changes due to the inclusions during heating at 1573 K (1300 °C) were studied by manual and automatic SEM-EDS analyses. Three alloys were used as specimens. The inclusions were Al{sub 2}TiO{sub 4} +TiN with a small amount of TiN in alloy #1, Al{sub 2}(Mg, Ti)O{sub 4} in alloy #2 and Al{sub 2}(Mg, Ti)O{sub 4} +TiN in alloy #3. The average grain size was smaller, and the ratio of columnar grains was lower in the as-cast alloy #2 and as-cast alloy #3 than that in the as-cast alloy #1. This is attributed to the heterogeneous nucleation of delta ferrite on Al{sub 2}(Mg, Ti)O{sub 4} during solidification. Refinement of the microstructures of ferritic steel by Mg-bearing oxide + multi-TiN inclusions is proposed. Changes in composition, aspect ratio, and size distribution of inclusions in each alloy during heating were investigated systematically. Mg-bearing oxide(+TiN) was dispersed in both the as-cast alloys and heated alloys, which contributed to microstructural refinement of the heated alloys through the pinning effect.

36 MATERIALS SCIENCE↗

Microstructure evolution and mechanical properties of Cu/Sn/Ag TLP-bonded joint during thermal aging

Highlights: • The thermal reliability of the Cu/Sn/Ag TLP-bonded joint was investigated through high-temperature storage. • A diffusion reaction occurred at the interface between Cu{sub 3}Sn and Ag{sub 3}Sn during thermal aging. • The mechanism of the Cu{sub 3}Sn/Ag{sub 3}Sn interfacial reaction was investigated from thermodynamics and kinetics. - Abstract: Low-temperature transient liquid phase (TLP) bonding is a promising joining technology for high-temperature electronic devices packaging. However, the effect of thermal aging on the joint microstructure and performance has been rarely studied so far. In this paper, the relationship between microstructural evolution and mechanical property was developed for the Cu/Sn/Ag TLP-bonded joint during 350 °C aging. Experimental results show that an interfacial reaction occurs between the intermetallic compounds (IMCs) of Cu{sub 3}Sn and Ag{sub 3}Sn, which induces that a great amount of Cu{sub 3}Sn particles or wedges embed into the Ag-Sn phase layer. The reaction process is controlled by a volume diffusion of Cu elements from the Cu substrate, and capable of promoting the transformation from Ag{sub 3}Sn into Ag(Sn) solid solution. Cu{sub 41}Sn{sub 11} phase can be formed at the expense of Cu{sub 3}Sn and Cu, of which transformation process is completely achieved after aging for 480 h, and the Cu(Sn) solid solution intimately contacts with the opposite Ag(Sn) solid solution in many areas after aging for 960 h. The joint mechanical property initially declines due to the formation of Cu{sub 41}Sn{sub 11} phase and Cu-Sn IMCs grain coarsening, and then increases because of the complete depletion of Cu{sub 3}Sn and substantial precipitation of Cu(Sn) solid solution. After aging for nearly 1000 h, the joint still maintains a high shear strength of >40 MPa, indicating an excellent thermal reliability.

36 MATERIALS SCIENCE↗

Global and local texture development during initial plastic deformation of cold-pilgered Zircaloy-4 tubing

In this work we present a thorough characterization of the texture development during the initial step of a cold pilgering process of a Zircaloy-4 TREX tube, on which the axial cross section is reduced by 80% over a 40cm length with an overall Q-ratio of 2.34, followed by a recrystallization thermal treatment. Texture across a tapered specimen representing this working zone was characterized by neutron diffraction and high energy synchrotron x-ray diffraction at 28 positions (4 locations along its length and 7 locations across its thickness with 0.3 mm spatial resolution), and on the deformed end after the thermal treatment. Results show that the starting material (TREX tube) presents a texture gradient through its wall thickness, with the c poles aligned to the hoop direction at the outer surface (with radial and hoop Kearns factors: f R =0.36, f H = 0.50), and gradually rotating around the axial direction to become a quasi-radial orientation (~35 o out of the radial direction) at the inner surface ( f R =0.43, f H =0.35). The overall texture becomes more radial due to the cold pilgering, but the texture gradient remains during the whole deformation process, being always more radial at the inner surface, ( f R =0.53, f H =0.37 at 80%) than at the outer surface ( f R =0.41, f H =0.50at 80%). The most remarkable changes in texture produced by the rolling process is a 30 o rotation of the grains around their c-axis, producing a marked increase of the <11 2 ¯ 0> // axial fiber texture at expenses of the original <10 1 ¯ 0> // axial fiber texture observed in the TREX tube. The observed changes in texture during deformation were correctly explained by visco-plastic self-consistent (VPSC) modelling. This was achieved after the inclusion of the basal <a> slip system, which plays a central role to explain the 30 o rotation around the c-axis during deformation. The texture evolution was correctly described after the inclusion of a drag effect to grain rotation due to the interaction with neighbouring grains. The through thickness texture differences are greatly reduced by the recrystallization thermal treatment, with similar Kearns factors at the inner surface ( f R =0.50, f H =0.28) and the outer surface ( f R =0.48, f H =0.39). The predominance of the <10 1 ¯ 0> // axial fiber texture is recovered after recrystallization.

36 MATERIALS SCIENCE↗

An Investigation on Microstructure Evolution, Mechanical Properties, and Strain Aging of Mg-1.8Zn-0.7Si-0.4Ca Biomedical Alloy Processed by Equal Channel Angular Pressing

The influence of equal channel angular pressing (ECAP) on microstructure and mechanical behavior, as well as, strain aging during ECAP and post-ECAP of Mg-1.8Zn-0.7Si-0.4Ca biomedical alloy was examined. The alloy in solid solution heat-treated condition was processed by ECAP with route B{sub C} at 350 and 400 °C. The specimens ECAPed at 350 °C were aged at 125 and 150 °C for different times. The hardness and shear punch test results indicated that performing ECAP at 350 °C for 4 passes increases the hardness and shear strength of the alloy from 48 HV and 110 MPa to 71 HV and 188 MPa, respectively. It was revealed that the average grain size of the alloy decreases from 78 µm to about 3 µm after 4 passes of ECAP. Three precipitates of CaMgSi, Ca{sub 2}Mg{sub 6}Zn{sub 3}, and Mg{sub 2}Si were detected in the solid solution specimen. After 4 passes of ECAP at 350 °C, Ca{sub 2}Mg{sub 6}Zn{sub 3} was completely dissolved and the morphology of Mg{sub 2}Si changed from Chinese script to fiber-shaped particles. Dynamic strain aging occurred at high-temperature ECAP, and the specimens were overaged during post-ECAP aging. Small MgZn particles were detected in the overaged sample.

36 MATERIALS SCIENCE↗

Hydrostatic pressure effect on mechanical behavior and texture evolution of Al and Brass

The effect of hydrostatic pressure on shear strength and microstructural evolution of polycrystalline FCC metals was investigated. Hydrostatic pressure of up to 5 GPa was imposed on commercial purity aluminum and 70/30 brass samples using a modified opposed-anvil apparatus (tri-anvil) that allows for measurement of shear strength in thin foil specimens. Similar to the previous investigations made in BCC metals (Ta and Mo), the shear strength of FCC metals increases significantly as the pressure rises. At 5 GPa, the shear strength of aluminum increased to 8 times its value at atmospheric pressure and 70/30 brass increased by a factor of 2.7. Here, EBSD analysis reveals an evident accumulation of dislocations in all sheared samples, with an approximately 50% decrease in grain diameter. Texture analysis suggests that, in addition to helping form selectively oriented dislocation walls, hydrostatic pressure also serves as a threshold to select certain favorable orientations in sheared metals. We propose that these hydrostatic pressure effects are intrinsically due to the excess volume associated with the cylindrical strain field of dislocation lines.

36 MATERIALS SCIENCE↗

Microstructural and Textural Evolutions during β → α/ω Transformation in Biomedical Ti-15Mo Alloy and Its Effects on Mechanical Performance

This study investigated the precipitation behaviors and mechanical performance of Ti-15Mo alloy subjected to different treatment conditions. The microstructures were analyzed via scanning electron microscopy and transmission electron microscopy. The tensile properties and resultant fracture surfaces were investigated to determine the relationship between the phase transformation and mechanical performance. The Ti-15Mo alloy had a notable elongation due to no observable precipitation during solution treatment plus quenching (STQ). A high ultimate tensile strength (UTS) was obtained with a considerable amount of ω precipitates transformed during air cooling after solution treatment (ST). The coarse precipitates and additional precipitation free zones in the Ti-15Mo alloy treated with furnace cooling (FC) after ST induced a decrease in UTS. Furthermore, the absence of a continuous grain boundary α phase resulted in a lower strength in the specimen annealed at 600 °C after hot rolling. The alloy iso-aged after STQ exhibited good tensile properties with a UTS of 920 MPa and an elongation of 15%. The texture and variant relationship of the precipitates was analyzed with x-ray diffraction and electron backscatter diffraction. The common variants of the β matrix influenced the nucleation of precipitates in the Ti-15Mo alloy annealed after hot rolling, and the precipitates showed an obvious {01-10}α main texture. The variant selection of α precipitates at the grain boundary was caused by the two adjacent β grains in the alloy treated by FC after ST.

36 MATERIALS SCIENCE↗

Electrical property enhancement of non-heat-treatable wrought aluminum alloys using graphene additives

With growing efforts of electrification, aluminum’s role as a light-weight conductor material has become increasingly prominent. There is a critical need to improve the electrical performance of aluminum at room temperature and high operating temperatures. In this study, the effect of graphene nanoparticle additives on the electrical performance of a non-heat treatable alloy were (AA3003) explored. Graphene’s unusual structure and electronic properties were used to improve AA3003 properties. Here, in this work, the effects of graphene on the evolution of electrical properties and microstructural features have been explored on lab scale hot extruded AA3003-graphene composites. Hot pressing schedules and extrusion temperatures were varied to investigate changes in intermetallic dispersion characteristics in the presence of dispersed graphene. We measured a reduction of 10.3 % in the temperature coefficient of resistance in the AA3003 sample with 0.05 wt% graphene extruded at 400 °C, along with a maximum increase of 1.1 % in electrical conductivity at 20 °C. Increasing the hot-pressing times up to 8 hours was also found to consistently increase the electrical conductivity, due to increased precipitation of intermetallic phases. Despite being a non-heat treatable alloy, AA3003 displays interesting precipitation dynamics and grain recrystallization trends that can be modulated with varying levels of heat treatment, graphene concentrations, and hot extrusion process parameters.

36 MATERIALS SCIENCE↗

Microstructural evolution of 3C-SiC exposed to simultaneous neutron irradiation and helium implantation

The synergism of transmutant helium and irradiation defects is critically important to understand the performance of SiC when in service in nuclear environments. In this study, we exposed 3C-SiC in contact with a 2 μm Ni foil to neutron irradiation at 500 °C to 29 dpa in the high flux isotope reactor to simulate the simultaneous introduction of helium and irradiation defects into SiC. The combination of TEM observations and thermal desorption measurements helps to elucidate the impact of helium on the microstructural evolution in 3C-SiC. Thermal helium desorption spectra from ion-implanted and neutron-irradiated SiC showed a completely different desorption behavior in terms of the peak position and helium desorption flux. The identification of possible helium trapping sites was attempted by applying the first order dissociation model to the measured thermal helium desorption spectra. TEM observations of the neutron-irradiated samples showed that the presence of helium facilitated the stabilization of the defect clusters and promoted the formation of visible helium bubbles in SiC subject to simultaneous neutron irradiation and in-situ He implantation. Following the subsequent heat treatment during the thermal desorption measurements, large faceted helium bubbles were found along grain boundaries in the neutron-irradiated SiC with in-situ He implantation, while the helium bubbles in the grain interior were relatively smaller than those found in the neutron-irradiated sample without in-situ He implantation due to the reduced mobility of He-defect clusters. In conclusion, the He contents contained in the neutron-irradiated samples were quantified based on the experimental data from TEM and thermal desorption measurements.

36 MATERIALS SCIENCE↗

Elucidating microstructural evolution and hardness variation across friction self-piercing riveted Al-7055 using synchrotron X-ray scattering and advanced microscopy techniques

Friction self-piercing riveting (FSPR) is a unique hybrid joining technique that combines the advantages of mechanical interlocking, frictional heat, and solid-state joining (if metallurgically compatible) to produce crack free joints in high strength and/or low-ductility alloys at room temperature. Here, in the current study, Al-7055 sheets were joined using FSPR for lightweight automotive applications and significant microhardness variations were observed across the joint cross-section. A detailed microstructural characterization at multiple length scales was carried out using advanced electron microscopy and X-ray scattering techniques to provide a fundamental understanding of the process-structure-property relationships. The relative contributions of microstructural characteristics at various length scales (i.e., grain size, dislocation density, solute concentration, precipitate nature) to strengthening were estimated using existent formulations (i.e., Hall-Petch, Taylor, precipitate bypass/shear equations) and correlated to the observed microhardness values across different regions. Small-angle X-ray scattering and scanning transmission electron microscopy revealed significant changes in the size and volume fraction of precipitate species, i.e., GP-I Zones, η′, and Mg/Zn solute co-clusters, depending on the process region. It was observed that the dissolution of the small η′/GP-I zones (T ∼ 150–200 °C) in the heat-affected zone were the key reason for the hardness drop. Further, it was shown that solid-solution, dislocation, grain size and solute co-cluster strengthening played a key role in the thermo-mechanically affected zone and grain-refined zone (GRZ). Finally, these observations were leveraged along with the Zener-Holloman relationship and grain size in the GRZ to estimate the peak joining temperature of the GRZ (∼ 350 °C) near the steel rivet.

aluminum 7xxx alloy↗

Transforming an Ionic Conductor into an Electronic Conductor via Crystallization: In Situ Evolution of Transference Numbers and Structure in (La,Sr)(Ga,Fe)O 3–x Perovskite Thin Films

Mixed-conducting perovskites are workhorse electrochemically active materials, but typical high-temperature processing compromises their catalytic activity and chemo-mechanical integrity. Low-temperature pulsed laser deposition of amorphous films plus mild thermal annealing is an emerging route to form homogeneous mixed conductors with exceptional catalytic activity, but little is known about the evolution of the oxide-ion transport and transference numbers during crystallization. Here the coupled evolution of ionic and electronic transport behavior and structure in room-temperature-grown amorphous (La,Sr)(Ga,Fe)O 3-x films as they crystallize is explored. In situ ac-impedance spectroscopy with and without blocking electrodes, simultaneous capturing-synchrotron-grazing-incidence X-ray diffraction, dc polarization, transmission electron microscopy, and molecular dynamics simulations to evaluate isothermal and non-isothermal crystallization effects and the role of grain boundaries on transference numbers is combined. Ionic conductivity increases by ≈2 orders of magnitude during crystallization, with even larger increases in electronic conductivity. Consequently, as crystallinity increases, LSGF transitions from a predominantly ionic conductor to a predominantly electronic conductor. The roles of evolving lattice structural order, microstructure, and defect chemistry are examined. Grain boundaries appear relatively nonblocking electronically but significantly blocking ionically. The results demonstrate that ionic transference numbers can be tailored over a wide range by tuning crystallinity and microstructure without having to change the cation composition.

36 MATERIALS SCIENCE↗

Carbon Redistribution and Carbide Precipitation in a High-Strength Low-Carbon HSLA-115 Steel Studied on a Nanoscale by Atom Probe Tomography

HSLA-115 is a newly developed Cu-bearing high-strength low-carbon martensitic steel for use in Naval structural applications. This research provides, for the first time, a comprehensive compositional analysis of carbon redistribution and associated complex phase transformations in an isothermal aging study of HSLA-115 at 823 K (550 °C). Specifically, we characterize carbon segregation at lath boundaries, grain-refining niobium carbonitrides, cementite, and secondary hardening M2C carbides, in addition to copper precipitation, by 3D atom probe tomography (APT). Segregation of carbon (3 to 6 at. pct C) is observed at martensitic lath boundaries in the as-quenched and 0.12-hour aged microstructures. On further aging, carbon redistributes itself forming cementite and M2C carbides. Niobium carbonitride precipitates do not dissolve during the austenitizing treatment and are inherited in the as-quenched and aged microstructures; these are characterized along with cementite by synchrotron X-ray diffraction and APT. Sub-nanometer-sized M2C carbide precipitates are observed after the formation of Cu precipitates, co-located with the latter, indicating heterogeneous nucleation of M2C. The temporal evolution of the composition and morphology of M2C carbides at 823 K (550 °C) is described using APT; their precipitation kinetics is intertwined with Cu precipitates, affecting the bulk mechanical properties of HSLA-115. Phase compositions determined by APT are compared with computed compositions at thermodynamic equilibrium using ThermoCalc.

36 MATERIALS SCIENCE↗

Microstructural evolution and strengthening mechanisms in a heat-treated additively manufactured Al–Cu–Mn–Zr alloy

In this report the microstructural and strength evolution of an additively manufactured Al-8.6Cu-0.5Mn-0.9Zr alloy upon aging at 300, 350, and 400 °C is investigated. The strengthening phases of the alloy evolve significantly upon aging, with breakdown and spheroidization of the interconnected θ-Al 2 Cu network, dissolution of metastable θ'-Al 2 Cu precipitates, and precipitation of nanometric L1 2 -Al 3 Zr from a matrix supersaturated in Zr. In the peak-aged states, the alloy displays a favorable combination of strength and ductility, with a room-temperature yield strength of 314–341 MPa and ductility of 11–13%. The measured yield strengths for microstructures with different aging treatments are compared to predictions of yield strengths from grain boundary, solid solution, and particle strengthening contributions. The observed strain hardening behavior is related to fundamental precipitate and dislocation interactions. Comparison between predicted and measured strength values indicates a continued need for strengthening models specifically developed for the heterogeneous microstructures of additively manufactured alloys.

36 MATERIALS SCIENCE↗

Low-field magnetoresistance up to 400 K in double perovskite Sr{sub 2}FeMoO{sub 6} synthesized by a citrate route

A wet-chemistry technique, namely the citrate route, has been used to prepare high-quality polycrystalline samples of double perovskite Sr{sub 2}FeMoO{sub 6}. We report on the evolution of magnetic and magnetoresistive properties of the synthesized samples as a function of three parameters (i) the pH of the starting solution, (ii) the decomposition temperature of the citrate precursors and (iii) the sintering conditions. The low-field magnetoresistance (LFMR) value of our best samples is as high as 5% at room temperature for an applied magnetic field of 1 kOe. Additionally, the distinguishing feature of these samples is the persistence of LFMR, with a reasonably large value, up to 400 K which is a crucial parameter for any practical application. Our study indicates that the enhancement of LFMR observed is due to a good compromise between the grain size distribution and their magnetic polarization. -- Graphical abstract: The microstructure (left panel) and corresponding low-field magnetoresistance of one of the Sr{sub 2}FeMoO{sub 6} samples synthesized in the course of this work. Highlights: • Samples of Sr{sub 2}FeMoO{sub 6} are prepared using a citrate route under varying conditions. • Magnetoresistive properties are improved and optimized. • Low-field magnetoresitence values as large as 5% at 300 K/1 kOe are reported. • Persistence of low-field magnetoresistance up to 400 K.

36 MATERIALS SCIENCE↗

Incorporating physically-based microstructures in materials modeling: Bridging phase field and crystal plasticity frameworks

Here, the mechanical properties of materials systems are highly influenced by various features at the microstructural level. The ability to capture these heterogeneities and incorporate them into continuum-scale frameworks of the deformation behavior is considered a key step in the development of complex non-local models of failure. In this study, we present a modeling framework that incorporates physically-based realizations of polycrystalline aggregates from a phase field (PF) model into a crystal plasticity finite element (CP-FE) framework. Simulated annealing via the PF model yields ensembles of materials microstructures with various grain sizes and shapes. With the aid of a novel FE meshing technique, FE discretizations of these microstructures are generated, where several key features, such as conformity to interfaces, and triple junction angles, are preserved. The discretizations are then used in the CP-FE framework to simulate the mechanical response of polycrystalline α-iron. It is shown that the conformal discretization across interfaces reduces artificial stress localization commonly observed in non-conformal FE discretizations. The work presented herein is a first step towards incorporating physically-based microstructures in lieu of the overly simplified representations that are commonly used. In broader terms, the proposed framework provides future avenues to explore bridging models of materials processes, e.g. additive manufacturing and microstructure evolution of multi-phase multi-component systems, into continuum-scale frameworks of the mechanical properties.

36 MATERIALS SCIENCE↗

Precursor Evolution and Stress Corrosion Cracking Initiation of Cold-Worked Alloy 690 in Simulated Pressurized Water Reactor Primary Water

Stress corrosion crack initiation of two thermally-treated, cold-worked (CW) alloy 690 (UNS N06690) materials was investigated in 360oC simulated PWR primary water using constant load tensile (CLT) tests and blunt notch compact tension (BNCT) tests equipped with direct current potential drop (DCPD) for in-situ detection of cracking. SCC initiation was not detected by DCPD for either the 21% or 31%CW CLT specimens loaded at their yield stress after ~9,220 hours, however intergranular (IG) precursor damage and isolated surface cracks were observed on the specimens. The two 31%CW BNCT specimens loaded at moderate stress intensity after several cyclic loading ramps showed DCPD-indicated crack initiation after 10,400 hours of exposure at constant stress intensity, which was resulted from significant growth of IG cracks. The 21%CW BNCT specimens only exhibited isolated small IG surface cracks and showed no apparent DCPD change throughout the test. Post-test cross-section examinations revealed many grain boundary (GB) nano-cavities in the bulk of all the CLT and BNCT specimens particularly for the 31%CW materials. Cavities were also found along GBs extending to the surface suggesting an important role in crack nucleation. This paper provides an overview of the evolution of GB cavities and discusses their effects on crack initiation in CW alloy 690.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Transmission electron microscopy of the rapid solidification microstructure evolution and solidification interface velocity determination in hypereutectic Al-20at.%Cu after laser melting

The evolution of rapid solidification (RS) microstructure and solidification interface velocity has been studied experimentally by in-situ transmission electron microscopy and postmortem characterization for hypereutectic Al-20at.%Cu (37 wt.%Cu) after laser melting. Four morphologically distinct regions formed via growth modes changing from θ-Al 2 Cu phase dendrites to eutectic cell growth, possibly α-Al dendrite growth (α-cell), banded growth, and α-Al plane front growth. Tendency for faceting and low capacity for solute trapping limited the θ-phase dendrite growth to solidification interface velocity v < 0.07 m/s. Consequently, formation of pro-eutectic micro-constituent was suppressed, and RS microstructure formation was dominated by eutectic, α-cell, and banded morphology grains for the Al-20at.%Cu alloy. Eutectic growth operated for interface velocity of 0.1 m/s ≤ v < 0.3 m/s, with a transition from regular lamellar, 2-λ and 1-λ mode to a dense irregular morphology dominated by α-phase at v = 0.3 m/s. Interface temperature calculations indicated feasibility of α-cell growth mode for 0.3 m/s ≤ v < 0.7 m/s. Banded growth occurred for 0.7 m/s ≤ v < 1.3 m/s. Plane front α-phase growth was evident for interface velocities v ≥ 1.3 m/s. Previous work on rapid solidification microstructure development in hypereutectic Al-Cu alloys reported a regime of α-cell growth subsequently to eutectic and prior to transition to banded growth for Al-19at.%Cu (36 wt.%Cu), while for Al-22at.%Cu (40 wt.%Cu) eutectic growth transitioned directly to α-plane front growth without emergence of a banded regime. Finally, based on the current study the disappearance of the banded growth regime occurs for a composition larger than 20at.%Cu.

36 MATERIALS SCIENCE↗

Hot Rolling of ZK60 Magnesium Alloy with Isotropic Tensile Properties from Tubing Made by Shear Assisted Processing and Extrusion (ShAPE)

In the present work, we utilized Shear Assisted Processing and Extrusion (ShAPE), a solid-phase processing technique, to extrude hollow tubes of ZK60 Mg alloy. Hot rolling was performed on these as-extruded tubes (after slitting them longitudinally) to thickness reductions of 37%, 68%, and 93% to investigate their viability as rolling feedstock material. EBSD analysis showed the formation of twinned grains in the ShAPE processed material and a gradual re-orientation of the basal texture parallel to the extrusion direction with each rolling step. Moreover, an equiaxed grain size of 5.15 ± 3.39 μm was obtained in the ShAPE extruded material, and the microstructure was retained even after 93% rolling reduction. The rolled sheets also showed excellent tensile strengths and no mechanical anisotropy, a critical characteristic for formability. The unique microstructures developed and their excellent mechanical properties, combined with the ease of scalability of the process, make ShAPE a promising alternative to existing methods for producing rolling feedstock material.

36 MATERIALS SCIENCE↗

Revealing the effect of local stresses on twin growth mechanisms in titanium using synchrotron X-ray diffraction

Deformation twinning has a significant impact on the evolution of microstructure and mechanical response in hexagonal close packed (hcp) metals. Understanding the physical mechanisms associated with twin nucleation and growth processes is important to enable the broad use of hcp metals. While both nucleation and growth are conditioned by the local stress state, few studies have quantified it in bulk deformed samples. In this study, we reveal the effects of local stresses on twin thickening using in-situ synchrotron experiments with differential aperture X-ray microscopy. High purity Ti is deformed under four-point bending to activate {1012} tensile twins. Further, 3D stress fields with a spatial resolution of 0.5μm are mapped in the vicinity of low and high macroscopic Schmid factor (MSF) twins growing inside a grain. Reconciling this experimental analysis with recent twin growth models reveals that the growth of low MSF twins is limited by the nucleation of twin growth defects in the high-purity Ti sample. While growth-inducing defect nucleation may occur in many places on the interface of the high resolved shear stress (RSS)/MSF twin, the nucleation rate of twinning disconnections for the low MSF twin is high only at the end of the twin near a stress concentration. Once nucleated, these defects easily propagate into lower RSS regions of the grain resulting in twin growth. This work highlights the importance of stress concentrations not only for twin (embryo) nucleation, but also to the growth process of twins, particularly in low MSF twins.

36 MATERIALS SCIENCE↗