Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Influence of Annealing on Microstructure, Electrochemical, and Magnetic Properties of Co-Doped SrTiO{sub 3} Nanocubes

Effect of annealing on microstructure, electrochemical, and magnetic properties of Co-doped SrTiO{sub 3} nanocubes obtained by the hydrothermal method was studied. X-ray diffraction (XRD) results of all as-prepared and annealed Co-doped SrTiO{sub 3} samples revealed a cubic perovskite structure with the second phases of SrCO{sub 3} and Co{sub 3}O{sub 4}in as-prepared and annealed SrTi{sub 0.90}Co{sub 0.10}O{sub 3} samples, respectively. Agglomerated nanocubes could be clearly observed in all as-prepared and annealed Co-doped samples by scanning electron microscope (SEM) and transmission electron microscope (TEM). X-ray absorption near edge spectroscopy (XANES) results suggested the presence of Co{sup 2+} cations in as-prepared Co-doped SrTiO{sub 3} samples, while both of Co{sup 2+} and Co{sup 3+} cations were found in annealed Co-doped SrTiO{sub 3} samples. The cyclic voltammetry (CV) and galvanostatic charge-discharge (GCD) results of as-prepared and annealed SrTi{sub 1-x}Co{sub x}O{sub 3} (x = 0.05, 0.075 and 0.10) electrodes revealed pseudocapacitor behavior of the Faradaic redox reaction type. The specific capacitance (Csc) was affected by the increase of Co content in all as-prepared and annealed Co-doped SrTiO{sub 3} samples with an excellent cycling stability after 200 cycle test of 97.24% and the highest value of 75.28 F g{sup −1} at 1 A g{sup −1} in an annealed SrTi{sub 0.925}Co{sub 0.075}O{sub 3} electrode. Magnetization measurements at room temperature using vibrating sample magnetometer (VSM) revealed diamagnetic behavior of as-prepared SrTiO{sub 3} sample, whereas paramagnetic behavior was observed in all as-prepared Co-doped SrTiO{sub 3} samples. After annealing, undoped sample exhibited paramagnetic behavior, whereas ferromagnetic behavior was observed in all Co-doped SrTiO{sub 3} samples with the increase of saturation magnetization (M{sub s}) at 10 kOe from 0.58 to 1.63 emu/g and the coercive field (H{sub c}) from 43.71 to 123.87 Oe, suggested to originate from the face-center exchange (FCE) mechanism.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2019

Response of 14YWT alloys under neutron irradiation: A complementary study on microstructure and mechanical properties

Nanostructured ferritic alloys (NFAs) having sub-micron grain size with a high density of nano-oxides (NOs) (size of ~2-3 nm) are one of the best candidates for structural components in Generation IV nuclear systems. In this study, 14YWT NFA cladding tubes were irradiated in BOR60 reactor up to 7 dpa at 360-370 °C. Detailed microstructural analysis has been conducted using bright field transmission electron microscopy, bright field scanning transmission electron microscopy, energy filtered transmission electron microscopy, energy dispersive X-ray spectroscopy, electron energy loss spectroscopy and transmission Kikuchi diffraction techniques. This revealed cavities, <100> and <111> type dislocation loops, and α' precipitates forming after irradiation with relationships between cavities and NOs, and α' precipitates and NOs. Cavities mostly form on the NOs; whereas, α' precipitates form between the NOs where the point defect concentration is high. Moreover, α' precipitates are distributed homogenously on and around the dislocation loops which is consistent with the observation that there is no Cr segregation on dislocation loops. Grain boundaries were found to be mostly depleted in Cr; however, the characteristics of each grain boundary determines the Cr behavior and the α' denuded zone around the grain boundaries. Mechanical properties of the irradiated tubes have been determined by using both low force and high force nanoindentation techniques, resulting in 1.03±0.33 GPa and 0.82±0.20 GPa hardening, respectively. Dispersed barrier hardening calculations and nanoindentation measurements are in good agreement. In this paper, 14YWT NFA has been systematically studied after neutron irradiation to better understand its superior performance: low α' concentration, low swelling and low radiation-induced hardening.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Transient-Liquid-Phase Bonding of H230 Ni-Based Alloy Using Ni-P Interlayer: Microstructure and Mechanical Properties

Transient-liquid-phase bonding using Ni-P as an interlayer has been developed for H230 Ni-Cr-W solid-solution-strengthened Ni-based alloy. Two process parameters—composition of the interlayer and bonding time—have been varied to optimize the mechanical properties. H230 has been bonded into two sets of stacks (set I and II) for 8 and 4 hours using Ni-12P and Ni-6P interlayer, respectively, (wt pct) at 1423 K (1150 °C) and 12.7 MPa. The microstructure of both the stacks has three distinct regions—the joint centerline which showed the presence of pores, an isothermally solidified zone (ISZ) which did not have any carbide precipitates and base H230. Transmission electron microscopy and atom probe tomography showed a uniform microstructure, and an absence of any deleterious phases at the joint and in ISZ. Set I and set II had a yield strength of 76 and 86 pct of that of the H230 sheet, tested at 1023 K (750 °C). Here, the measured elongation at fracture was negligible, but the fracture surfaces revealed a ductile cup-and-cone-type fracture occurring through the ISZ/joint region. Examination of broken tensile samples revealed that the plastic strain was constrained to within one joint region through which fracture occurred.

14 SOLAR ENERGY↗
DOE OSTI2016

Microstructure and mechanical properties of aluminium matrix composites reinforced by Al{sub 62}Cu{sub 25.5}Fe{sub 12.5} melt spun ribbon

Aluminium matrix composites containing 15, 30 and 50 vol.% of pulverized Al{sub 62}Cu{sub 25.5}Fe{sub 12.5} (in at.%) melt spun ribbons have been prepared by a vacuum hot pressing (T = 673 K, P = 600 MPa). The microstructure of the initial ribbon and the composites was investigated using X-ray, scanning and transmission electron microscopy. In the as-spun ribbon the quasicrystalline icosahedral phase (i-phase) coexisted with the cubic copper rich β-Al(Cu, Fe) intermetallic compound. The phase composition of Al-Cu-Fe particles changed after consolidation process and the i-phase transformed partially to the ω-Al{sub 70}Cu{sub 20}Fe{sub 10} phase. Additionally, the Θ-Al{sub 2}Cu phase formed at the α(Al)/Al-Cu-Fe particle interfaces. With an increase in volume fraction of the reinforcement the hardness of the composites increased up to HV = 180 for the highest amount of added particles. The ultimate compression strength of the same sample reached the value of 545 MPa. - Highlights: • Al and 15, 30, 50% of pulverized Al{sub 62}Cu{sub 25.5}Fe{sub 12.5} melt spun ribbon were consolidated. • The initial ribbon consisted of the icosahedral i-phase and copper rich β-Al(Cu, Fe). • The i-phase partially transforms to ω-Al{sub 7}Cu{sub 2}Fe phase in all composites. • Increase of microhardness and compressive strength with content of reinforcement • Ultimate compression strength 545 MPa for 50% of added particles.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Microstructures and tribological properties of laser cladded Ti-based metallic glass composite coatings

Metallic glass composite coatings Ti{sub 45}Cu{sub 41}Ni{sub 9}Zr{sub 5} and Ti{sub 45}Cu{sub 41}Ni{sub 6}Zr{sub 5}Sn{sub 3} (at.%) on a Ti-30Nb-5Ta-7Zr (wt.%) (TNTZ) alloy were prepared by laser cladding. The microstructures of the coatings were characterized by means of X-ray diffractometry (XRD), scanning electron microscopy (SEM) equipped with energy dispersive X-ray analyzer (EDXA), and transmission electron microscopy (TEM). Results indicated that the coatings have an amorphous structure embedded with a few nanocrystalline phases and dendrites. A partial substitution of Ni by Sn can improve the glass forming ability of Ti-base metallic glass system, and induce the formation of nano-sized Ni{sub 2}SnTi phase during the cyclic laser heating. The tribological behavior of both the substrate and the coatings was investigated in detail. A significant improvement in both the hardness and the wear resistance of the coatings was achieved with the addition of Sn. The relationship between the wear resistance and the microstructures of the coatings was discussed. - Highlights: •Ti-based metallic glass composite coatings were prepared by laser cladding. •The wear resistance is greatly improved by laser cladding of composite coatings. •Substitution of Ni by Sn increases GFA and wear resistance of the coatings. •A good balance of crystalline/amorphous phases improves the wear resistance. •Adhesive wear serves as the dominant wear mechanism of the composite coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Structural, microstructural and thermal properties of lead-free bismuth–sodium–barium–titanate piezoceramics synthesized by mechanical alloying

Graphical abstract: Mechano-synthesis of lead-free (Bi{sub 0.5}Na{sub 0.5}){sub 0.94}Ba{sub 0.06}TiO{sub 3} piezoceramics with nanocrystalline/amorphous structure and homogeneous composition: partial transformation of constituents to BNBT, BNT and pyrochlore, amorphous phase formation, mechano-crystallization of the amorphous, pyrochlore-to-perovskite BNBT phase transformation during the process. Display Omitted Highlights: ► Perovskite BNBT powders with homogeneous composition were synthesized by MA. ► Partial transformation of constituents to BNBT, BNT and pyrochlore occurred by MA. ► Formation of an amorphous phase and afterwards its crystallization occurred by MA. ► Pyrochlore-to-perovskite BNBT phase transformation occurred after prolong milling. ► Polymorphic transformations of TiO{sub 2} act as the main alloying impediment during MA. -- Abstract: Bismuth–sodium–barium–titanate piezoceramics with a composition of (Bi{sub 0.5}Na{sub 0.5}){sub 0.94}Ba{sub 0.06}TiO{sub 3} (BNBT) were prepared by mechanical alloying (MA). Structural analysis and phase identification were performed by X-ray diffraction (XRD). Microstructural studies and chemical composition homogeneity were performed by scanning electron microscope (SEM) coupled with energy dispersive X-ray analysis (EDX). Furthermore, thermal properties of the as-milled powders were evaluated by thermogravimetry/differential thermal analysis (TG/DTA). During the initial milling, the constituents were transformed to the perovskite, pyrochlore, and BNT phases; in addition, partial amorphization of the structure appeared during the milling cycle. As MA progressed, transformation of pyrochlore-to-perovskite and crystallization of the amorphous phase occurred and also, the BNBT phase was significantly developed. It was found that the MA process has the ability to synthesize the BNBT powders with a submicron particle size, regular morphology, and uniform elemental distribution.

36 MATERIALS SCIENCE↗
DOE OSTI2012

Microstructure and mechanical properties of 7075 aluminum alloy nanostructured composites processed by mechanical milling and indirect hot extrusion

Nanostructured composites of 7075 aluminum alloy and carbon coated silver nanoparticles were produced by mechanical milling and indirect hot extrusion. The milling products were obtained in a high energy SPEX ball mill, and then were compacted by uniaxial load and pressure-less sintered under argon atmosphere. Finally, the sintered product was hot extruded. Carbon coated silver nanoparticles were well distributed in the matrix of the extruded material. Tensile tests were carried out to corroborate the hypothesis that second phase particles, well dispersed in the matrix, improve the strength of the material. High resolution transmission electron microscopy was employed to locate and make sure that the silver nanoparticles were homogeneously and finely dispersed. Highlights: Black-Right-Pointing-Pointer 7075 Al nanostructured composites can be produced by mechanical milling. Black-Right-Pointing-Pointer Carbon coated silver nanoparticles are well dispersed into aluminum matrix. Black-Right-Pointing-Pointer Ductile Ag-C NP's improve the mechanical properties of the 7075 Al-alloy. Black-Right-Pointing-Pointer Ag-C NP's content has an important effect in the particle and crystallite size. Black-Right-Pointing-Pointer Ag-C NP's keep their morphology after milling and conformation processes.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Effects of various Mg/Si ratios on microstructure and performance property of Al-Mg-Si alloy cables

High quality AA6101 aluminum cables are critical to electrical industry to meet the energy consumption requests. In the present work, the influence of Mg/Si ratios on the electrical conductivity and mechanical properties of AA6101 aluminum alloy was investigated. Wheatstone Bridge method and tensile test were employed to characterize the mechanical properties. X-ray Diffraction (XRD), Scanning Electron Microscope (SEM) and Transmission Electron Microscope (TEM) were used to understand the morphology of the precipitation and the mechanism of age hardening. It is found that excessive Si benefits high strength and high conductivity while excessive Mg plays a negative role in the strength and the conductivity of AA6101 cables. Excessive Si elements promote both the precipitating rate and quantity of β″ phase therefore increase the tensile strength. Excessive Si elements also help with decreasing the lattice distortion, which contributes to the enhancement of the conductivity. Excessive Mg elements lead to more dissolved Mg after aging treatment, therefore increase lattice distortion of the matrix and promote the deposit of coarse Mg-enriched secondary phase. - Highlights: •A new available method to improve the mechanical and electrical properties of Al-Mg-Si alloy •Investigation on the role of various Mg/Si ratios in the changes of comprehensive performances •Discussions on the morphology of the precipitation phases and the mechanism of hardening.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Formation of gradient microstructure and mechanical properties of hot-pressed W-20 wt% Cu composites after sliding friction severe deformation

Highlights: • W particles of composites were refined during sliding friction treatment (SFD). • Dislocation, dislocation tangles and boundary clearly exist in deformed W particle. • YS and UTS of SFDed sample are 308.74 MPa and 553.60 MPa owing to the refinement. • Electrical conductivity of SFDed sample decreased from 33 IACS% to 28.5 IACS%. • Fracture mode changing from inter-granular mode to trans-granular. - Abstract: W-based alloys are currently considered promising candidates for high heat flux components in future fusion reactors. In this paper, hot pressed W-20 wt%Cu composites were treated at room temperature using a sliding friction severe deformation (SFD) process, with a moving speed of 0.2 m/s and an applied load of 500 N. Microstructural evolution of composites after the SFD treatment was evaluated and compared with that of the untreated composites. Results showed that there was a gradient structure generated and an obvious refinement in tungsten particles size in the surface layer after the SFD process. The average particle size of tungsten in the SFD treated composites was 2.60 μm, whereas it was 4.5 μm for tungsten in the untreated composites. Fracture surfaces of the composites indicated that the SFD treatment destroyed the W skeleton and changed fracture mode from predominant inter-granular one to trans-granular one due to the decrease in contact area of W-W inter-particles. Yield strength and ultimate tensile strength of composites after the SFD treatment were 308 MPa and 553 MPa, respectively. The treated composites exhibited micro-hardness values with an average reading of about 308 HV. Analysis of the facture microstructures clearly suggested that the tungsten particles in the treated composites are consisted of dislocations and boundaries as well as dislocation tangles. The electrical conductivity of the composites was decreased from 33 IACS% to 28.5 IACS% after the SFD treatment, mainly due to loss or squeezing of copper into the inner surface.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Retrogression Heat Treatment Time on Microstructure and Mechanical Properties of AA7010

The effect of retrogression time during retrogression and re-aging (RRA) treatment of AA7010 is evaluated by performing tensile tests and characterizing the microchemistry of the grain boundary precipitates (GBPs) using transmission electron microscope coupled with the energy-dispersive spectroscopy. Retrogression time is evaluated so that the ultimate tensile strength of the RRA-treated sample is equal to that of the T6-treated sample and the grain boundary microstructure similar to that of the over-aged (T7451) condition. The investigation reveals that the sample retrogressed at 200 °C for 20 min has UTS of 586 MPa which is equivalent to that of the T6 sample and 11.5% higher than that of the T7451 condition. The fracture toughness of the RRA-treated sample was 41 MPa√m. Microstructure of the RRA-treated sample is similar to T7451, along the grain boundaries and in the grain interior similar to that of the T6-treated sample. Energy-dispersive spectroscopy confirmed the increment of Cu content on the GBP’s with increase in the retrogression time, which is expected to improve the stress corrosion cracking resistance of the alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2019

The Effect of Weld Metal Composition on Microstructural and Mechanical Properties of Dissimilar Welds Between Monel 400 and Inconel 600

The current work was carried out to characterize welding of Inconel 600 superalloy and Monel 400. In the present study, gas tungsten arc welding (GTAW) with four types of filler metals (ENiCu, ENiCu-7, ENiCr-3 and ENiCrFe-3) was utilized. The filler metals were categorized into two groups based on the presence of Cr and Nb in their chemical composition. This paper describes the selection and application of welding consumables in manufacturing dissimilar metal combinations. It was found that (Nb/Cr) ratio and Fe content can affect on the size and amount of carbides. During solidification of ENiCr-3 and ENiCrFe-3 filler metals, Nb leaves dendritic cores and is rejected to inter-dendritic regions because of its high tendency for segregation. However, No brittle Laves phase was detected in the welds. The interface between weld metal and base metal and gradual changes in alloying elements were also investigated by scanning electron microscopy. EDX analysis was also applied for different samples. Microhardness measurements and tensile test were performed on the joints. The average hardness value in the weld metal obtained from ENiCrFe-3 is higher than the other welds. ENiCu-7 weld exhibited the highest tensile strength of 540 MPa and percent elongation of 53% in contrast to ENiCrFe-3 weld with the lowest tensile strength (518 MPa) and percent elongation (39%).

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Ti Addition on the Microstructure and Mechanical Properties of Weld Metals in HSLA Steels

Acicular ferrite (AF) can significantly improve the mechanical properties of steel welds. One practical approach to enhance the formation of AF is to provide the heterogonous nucleation sites such as Ti oxides. In this study, Ti was added to different conventional welding processes including shield metal arc welding (SMAW), submerged arc welding (SAW) and tandem SAW (T-SAW). In the SMAW process, TiO{sub 2} particles as a source of Ti were inserted into the weld groove, while in the SAW and the T-SAW processes, the Ti-enriched S2MoTB wire was used as the filler metal. The microstructural evolution of weldments was characterized by employing optical and scanning electron microscopes. In addition, microhardness (Vickers, HV), Charpy impact and tensile tests were carried out to investigate the mechanical properties of weldments. Although the microhardness measurements of all weldments did not vary significantly and were in the range of 205-252 HV, there was a considerable difference in tensile and impact properties of the SAW and the T-SAW weldments. In the SMAW process, the addition of TiO{sub 2} results in no significant enhancement in tensile and impact toughness. This can be attributed to the inhomogeneous distribution of TiO{sub 2} particles as well as the formation of large inclusions in the structure. On the other hand, Ti addition to WM increased the yield strength from 489 to 552 MPa for the SAW process, and in contrast, it decreased the impact toughness from 75 to 33 J. This detrimental effect can be related to the higher deposition of other alloying elements in the WM and the formation of more ferrite side plate phase. By applying the T-SAW process, more Ti in WM led to a higher content of AF in the microstructure and increased both yield strength and impact toughness from 528 to 595 MPa and 100 to 180 J, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructural and infiltration properties of woven preforms during chemical vapor infiltration

Interface-resolved direct numerical simulations (DNSs) of chemical vapor infiltration (CVI) have been performed over a range of furnace-operating conditions (Thiele moduli) and for practical woven preform geometries. A level-set method is used to resolve the geometry of the initial preform at tow scale. The interface between the vapor and solid phase is then evolved in time through the entire CVI densification cycle, fully resolving the time-varying topology between the two phases. In contrast to previous level-set methods for CVI simulation, the physical reaction and diffusion processes govern the level-set movement in the current approach. The surface deposition kinetics is described by the usual one-step model. In this paper, the DNS data are used to study the evolving porosity, surface-to-volume ratio, and flow infiltration properties (permeability and effective diffusivities). Additionally, comparisons are made to popularly-assumed structure functions and the standard, Kozeny–Carmen porous media model commonly employed in modeled CFD simulations of CVI. The virtual DNS experiments reveal a Thiele modulus and preform geometry (fabric layup) dependence which the existing microstructural and infiltration models are not able to describe throughout the entire densification process. The DNS-based, woven geometry-specific correlations can be applied directly to mean-field, furnace-scale CFD simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure and mechanical properties of pure copper wire produced by shear assisted processing and extrusion

Shear assisted processing and extrusion (ShAPE) process can consolidate powdered materials and simultaneously extrude wire or tube with improved properties. We successfully produced copper wire extrusions from powder and solid materials for the first time. The extrusion pressure of ShAPE process is at least two times less than that required for conventional extrusion. We used optical microscopy to inspect and validate the integrity of extrudates. It shows that the microstructure was refined and dynamically recrystallized to equiaxial grains. Compared to the annealed copper wire, ShAPE processed wire has 80% higher yield strength, 15% higher ultimate tensile strength and 20% higher ductility. These were correlated with refined grain size and sub-structuring observed via electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM).

Copper, Wire, Shear Assisted Processing and Extrus↗
DOE OSTI2013

Effect of freeze-drying and self-ignition process on the microstructural and electrochemical properties of Li{sub 4}Ti{sub 5}O{sub 12}

Graphical abstract: - Highlights: • Li{sub 4}Ti{sub 5}O{sub 12} is prepared by a method involving self-ignition of a freeze-dried gel. • Addition of NH{sub 4}NO{sub 3} modifies the self-ignition propagation mode. • Well-crystallized Li{sub 4}Ti{sub 5}O{sub 12} phase is obtained after only 2 h at 800 °C. • Li{sub 4}Ti{sub 5}O{sub 12} powder has 161 mAh g{sup −1} capacity and good retention at C/4 rate. - Abstract: Crystalline Li{sub 4}Ti{sub 5}O{sub 12} is synthesized by a method involving the freeze-drying and self-ignition of a gel prepared from titanium isopropoxide, lithium nitrate and hydroxypropylmethylcellulose (HPMC). This synthesis route yields crystalline Li{sub 4}Ti{sub 5}O{sub 12} particles after calcination at 800 °C for 2 h. In an alternative route, addition of ammonium nitrate shifts the self-ignition mode from wave-like propagation to simultaneous. Powders with different microstructures are thereby obtained. Electrochemical characterization shows that the best results for Li{sup +} intercalation/desintercalation are obtained for the powder prepared without ammonium nitrate addition. These results highlight the necessity for a control of the self-ignition mode to obtain adequate properties.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Microstructure and thermal properties of copper–diamond composites with tungsten carbide coating on diamond particles

An effective method for preparing tungsten carbide coating on diamond surfaces was proposed to improve the interface bonding between diamond and copper. The WC coating was formed on the diamond surfaces with a reaction medium of WO{sub 3} in mixed molten NaCl–KCl salts and the copper–diamond composites were obtained by vacuum pressure infiltration of WC-coated diamond particles with pure copper. The microstructure of interface bonding between diamond and copper was discussed. Thermal conductivity and thermal expansion behavior of the obtained copper–diamond composites were investigated. Results indicated that the thermal conductivity of as-fabricated composite reached 658 W m{sup −} {sup 1} K{sup −} {sup 1}. Significant reduction in coefficient of thermal expansion of the composite compared with that of pure copper was obtained. - Highlights: • WC coating was successfully synthesized on diamond particles in molten salts. • WC coating obviously promoted the wettability of diamond and copper matrix. • WC coating greatly enhanced the thermal conductivity of Cu–diamond composite. • The composites are suitable candidates for heat sink applications.

36 MATERIALS SCIENCE↗
DOE OSTI2011

Tunning of microstructure and thermoelectric properties of Ca{sub 3}Co{sub 4}O{sub 9} ceramics by high-magnetic-field sintering

The structural, magnetic, electrical, and thermal transport properties of Ca{sub 3}Co{sub 4}O{sub 9} ceramics sintered under high magnetic field were investigated. Crystal grain texturing and densification were achieved through cold-pressing and high-magnetic-field sintering techniques. The c-axis of the layered crystal grain was partly oriented along the c-axis of the pressed samples via a cold-pressing technique, and the degree of orientation was further increased while applying the magnetic field in the sample sintering progress. The easy magnetization axis of Ca{sub 3}Co{sub 4}O{sub 9} polycrystalline ceramics was found to be the c-axis. The room-temperature resistivity along the ab-plane of the sample sintered under 8 T magnetic field was about 30% smaller than that of the sample sintered without magnetic field, and the Seebeck coefficient of the former reached 177.7 {mu}V/K at the room temperature, which is about 50% larger than that of the latter. Consequently, for the sample sintered at 8 T magnetic field, the power factor along the ab-plane was enhanced by about 1.8 times compared to the sample without magnetic field sintering. The obtained result is suggested to originate from the variations of the carrier mobility and spin-orbital degeneracy due to high-magnetic-field sintering in the progress of the sample preparation.

36 MATERIALS SCIENCE↗