Air-Stable Monolayer Cu 2 Se Exhibits a Purely Thermal Structural Phase Transition
Not provided.
Chemistry↗
SEARCH · Search NASA
Results for “PHASE STUDIES”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Effect of Chemical Composition on the Microstructure and Properties of the Ag-Ga-Ge Alloys
This study presents a comparison of thermodynamically calculated phase compositions of Ag-Ga-Ge alloys at fixed temperatures with phase analysis results of alloys annealed at respective temperatures. Three isothermal sections of the Ag-Ga-Ge system at 25, 100 and 300 °C have been extrapolated using optimized thermodynamic parameters from the literature. An experimental analysis of the microstructure was carried out using optical microscopy, scanning electron microscopy and energy-dispersive spectrometry. Results obtained by x-ray powder diffraction methods (identified phases and lattice parameters) were compared with the results of the predicted phase equilibria. Good overall agreement between experimental and calculated values was obtained. The Brinell hardness and electrical conductivity of selected alloys were measured and obtained results were analyzed with respect to their overall compositions and phase constituents.
36 MATERIALS SCIENCE↗
Reversible Electrochemical Lithium Cycling in a Vanadium(IV)- and Niobium(V)-Based Wadsley–Roth Phase
Fast charging remains one of the greatest safety challenges in Li-ion batteries due to Li-dendrite growth occurring on graphite anodes if they are lithiated too quickly. The search for high-rate anodes has highlighted materials in the Wadsley–Roth (WR) shear phase family. The relative abundance of V compared with traditional WR compositions of Nb and W makes V-based phases attractive. However, the high voltage and poor reversibility typically associated with V redox have made V-rich WR phases less studied than Nb- and W-rich phases. Here, we show that a new V-rich Wadsley–Roth phase, V 7 Nb 6 O 29 , achieves excellent rate capability and 80% capacity retention after 228 cycles with a relatively low average voltage of 1.76 V vs Li/Li + compared with other V-rich WR phases. Single-crystal X-ray diffraction reveals a P4/m space group with repeating 2 × 2 × ∞ and 3 × 3 × ∞ blocks of V 4+ and Nb 5+ octahedra. Finally, combined neutron pair distribution function analysis, X-ray absorption spectroscopy, and density functional theory calculations show that V redox is the primary source of capacity and that cycling stability is provided by the stable octahedral coordination adopted by V 4+ in the material.
25 ENERGY STORAGE↗
Pressure-induced phase transition in barium hydride studied with neutron scattering
Barium hydride can undergo a structural phase transition from an orthorhombic phase to a hexagonal phase induced by high temperature or high pressure. This transition causes an immediate increase in the hydrogen diffusion rates by over an order of magnitude, and therefore, understanding the origin and details of such transition is of great interest not only for fundamental reasons but also for improving materials for future applications. In this work, the pressure evolution of the crystal structure was characterized using neutron powder diffraction up to a maximum pressure of 11.3 GPa. The pressure dependence of the unit cell volumes, lattice parameters, atomic sites, and compressibilities were determined for both phases. A structural phase transition occurred over a wide pressure range of P = 1.3 GPa–4.9 GPa. The transition to the higher density hexagonal phase reduced the volume per formula unit of BaD 2 by 13.6%, hence increasing the volumetric storage density. In addition, we investigated the hydrogen diffusion process using high pressure quasi-elastic neutron scattering up to 7.1 GPa. Our results show that the hydrogen mobility increases with pressure in the hexagonal phase. This work sheds light on the structural and dynamical aspects of barium hydride caused by the application of high pressure. Finally, the results may aid in the development of advanced metal hydride systems with increased hydrogen dynamics.
36 MATERIALS SCIENCE↗
Pair Density Wave in the Doped t - J Model with Ring Exchange on a Triangular Lattice
In our previous study, we found a quantum spin liquid phase with a spinon Fermi surface in the two dimensional spin-1/2 Heisenberg model with four-spin ring exchange on a triangular lattice. In this work we dope the spinon Fermi surface phase by studying the $t - J$ model with four-spin ring exchange. We perform density matrix renormalization group calculations on four-leg cylinders of a triangular lattice and find that the dominant pair correlation function is that of a pair density wave; i.e., it is oscillatory while decaying with distance with a power law. The doping dependence of the period is studied. This is the first example where a pair density wave is the dominant pairing in a generic strongly interacting system where the pair density wave cannot be explained as a composite order and no special symmetry is required.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Phase Transformations In Mullite-Precursor Xerogels
Report describes experimental study of phase transformations occurring in monophasic and diphasic xerogels of overall stoichiometric mullite composition during thermal treatment. Mullite valued as refractory material because of relatively high mechanical strength, excellent resistance to thermal shock, high resistance to creep, low density, low thermal conductivity, and stability at high temperature. Part of continuing effort to develop precursor materials transformed into mullite and sintered at temperatures low enough to avoid degradation of non-mullite reinforcing fibers in manufacture of mullite/fiber composites.
Hyatt, Mark J.↗
A Gaussian measure of quantum phase noise
We study the width of the semiclassical phase distribution of a quantum state in its dependence on the average number of photons (m) in this state. As a measure of phase noise, we choose the width, delta phi, of the best Gaussian approximation to the dominant peak of this probability curve. For a coherent state, this width decreases with the square root of (m), whereas for a truncated phase state it decreases linearly with increasing (m). For an optimal phase state, delta phi decreases exponentially but so does the area caught underneath the peak: all the probability is stored in the broad wings of the distribution.
Schleich, Wolfgang P.↗
MARSNET surface and atmosphere investigations
Following an ESA preliminary study on the possible areas of European participation in the future international exploration of Mars and a recent ESA in-depth scientific and technical assessment study, MARSNET was selected for further phase-A studies as a potential European contribution to such exploration. The MARSNET mission consists of a network of small stations to be landed on the surface of Mars. All surface stations will have identical design and payload, and will be located several thousand km apart from each other. The required operational lifetime on the surface of Mars for all landers is one Martian year (687 days) to carry out long-term meteorological and seismological measurements. The availability of a data relay orbiter at low altitude is assumed. The instruments are mounted on a platform under the semi-hard lander solar array. The main scientific goals of the mission during the atmospheric descent and on the surface are outlined.
Chicarro, A. F.↗
Optimal Electrodynamic Tether Phasing Maneuvers
We study the minimum-time orbit phasing maneuver problem for a constant-current electrodynamic tether (EDT). The EDT is assumed to be a point mass and the electromagnetic forces acting on the tether are always perpendicular to the local magnetic field. After deriving and non-dimensionalizing the equations of motion, the only input parameters become current and the phase angle. Solution examples, including initial Lagrange costates, time of flight, thrust plots, and thrust angle profiles, are given for a wide range of current magnitudes and phase angles. The two-dimensional cases presented use a non-tilted magnetic dipole model, and the solutions are compared to existing literature. We are able to compare similar trajectories for a constant thrust phasing maneuver and we find that the time of flight is longer for the constant thrust case with similar initial thrust values and phase angles. Full three-dimensional solutions, which use a titled magnetic dipole model, are also analyzed for orbits with small inclinations.
Bitzer, Matthew S.↗
Overview of 2008 Outer Planet Flagship Studies
This slide presentation reviews the process involved in the Phase-2 studies for the next Outer Planets Flagship (OPF). These studies will be a cooperative effort with ESA and JAXA in partnership with NASA. The annoucement of oppurtunity (AO) for the science instruments and the launch approval/planetary protection processes are reviewed. There is also discussion about capturing relevant lessons from the Cassini team, supporting international collaboration, and support for science definition teams. Some mission specific tasks are also reviewed, for the three missions being proposed: (1) Europa Explorer, (2) Jupiter System Observer and (3) Titan Explorer. A timeline for the studies is also included.
outer planets↗
Multi-phase equation of state of ultrapure hafnium to 120 GPa
Hafnium (Hf) is an industrially important material due to its large neutron absorption cross-section and its high corrosion resistance. When subjected to high pressure, Hf phase transforms from its hexagonal close packed α-Hf phase to the hexagonal ω-Hf phase. Upon further compression, ω-Hf phase transforms to the body centered cubic β-Hf phase. In this study, the high pressure phase transformations of Hf are studied by compressing and decompressing a well-characterized Hf sample in diamond anvil cells up to 120 GPa while collecting x-ray diffraction data. The phase transformations of Hf were compared in both a He pressure transmitting medium (PTM) and no PTM over several experiments. It was found that the α-Hf to ω-Hf phase transition occurs at a higher pressure during compression and lower pressure during decompression with a helium (He) PTM compared to using no PTM. Finally, there was little difference in the ω-Hf to β-Hf phase transition pressure between the He PTM and no PTM. The equation of state was fit for all three phases of Hf and under both PTM and no-PTM.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Two-phase detonations and drop shattering studies Annual progress report, 1 Feb. 1966 - 31 Jan. 1967
Detonation measurements of two-phase liquid-gas mixtures, and drop shattering studies
TWO-PHASE SYSTEM↗
Large space telescope, phase A. Volume 1: Executive summary
The Phase A study of the Large Space Telescope (LST) is reported. The study defines an LST concept based on the broad mission guidelines provided by the Office of Space Science (OSS), the scientific requirements developed by OSS with the scientific community, and an understanding of long range NASA planning current at the time the study was performed. The LST is an unmanned astronomical observatory facility, consisting of an optical telescope assembly (OTA), scientific instrument package (SIP), and a support systems module (SSM). The report consists of five volumes. The report describes the constraints and trade off analyses that were performed to arrive at a reference design for each system and for the overall LST configuration. A low cost design approach was followed in the Phase A study. This resulted in the use of standard spacecraft hardware, the provision for maintenance at the black box level, growth potential in systems designs, and the sharing of shuttle maintenance flights with other payloads.
Source record↗
Piloted simulation study of two tilt-wing control concepts
A two-phase piloted simulation study was conducted to investigate alternative wing and flap controls for tilt-wing aircraft. The initial phase of the study compared the flying qualities of both a conventional (programmed) flap and an innovative geared flap. The second phase of the study introduced an alternate method of pilot control for the geared flap and further studied the flying qualities of the programmed flap, and two geared flap configurations. In general, the pilot rating showed little variation between the programmed flap and the geared flap control concepts. Some differences between the two concepts were noticed and are discussed in this paper. The addition of pitch attitude stabilization in the second phase of the study greatly enhanced the aircraft flying qualities. This paper describes the simulated tilt-wing aircraft and the flap control concepts and presents the results of both phases of the simulation study.
Birckelbaw, Lourdes G.↗
High-Speed Soft-Decision Decoding of Two Reed-Muller Codes
In this research, we have proposed the (64, 40, 8) subcode of the third-order Reed-Muller (RM) code to NASA for high-speed satellite communications. This RM subcode can be used either alone or as an inner code of a concatenated coding system with the NASA standard (255, 233, 33) Reed-Solomon (RS) code as the outer code to achieve high performance (or low bit-error rate) with reduced decoding complexity. It can also be used as a component code in a multilevel bandwidth efficient coded modulation system to achieve reliable bandwidth efficient data transmission. This report will summarize the key progress we have made toward achieving our eventual goal of implementing, a decoder system based upon this code. In the first phase of study, we investigated the complexities of various sectionalized trellis diagrams for the proposed (64, 40, 8) RM subcode. We found a specific 8-trellis diagram for this code which requires the least decoding complexity with a high possibility of achieving a decoding speed of 600 M bits per second (Mbps). The combination of a large number of states and a high data rate will be made possible due to the utilization of a high degree of parallelism throughout the architecture. This trellis diagram will be presented and briefly described. In the second phase of study, which was carried out through the past year, we investigated circuit architectures to determine the feasibility of VLSI implementation of a high-speed Viterbi decoder based on this 8-section trellis diagram. We began to examine specific design and implementation approaches to implement a fully custom integrated circuit (IC) which will be a key building block for a decoder system implementation. The key results will be presented in this report. This report will be divided into three primary sections. First, we will briefly describe the system block diagram in which the proposed decoder is assumed to be operating, and present some of the key architectural approaches being used to implement the system at high speed. Second, we will describe details of the 8-trellis diagram we found to best meet the trade-offs between chip and overall system complexity. The chosen approach implements the trellis for the (64, 40, 8) RM subcode with 32 independent sub-trellises. And third, we will describe results of our feasibility study on the implementation of such an IC chip in CMOS technology to implement one of these sub-trellises.
Lin, Shu↗
Circuit Design Approaches for Implementation of a Subtrellis IC for a Reed-Muller Subcode
In this research, we have proposed the (64, 40, 8) subcode of the third-order Reed-Muller (RM) code to NASA for high-speed satellite communications. This RM subcode can be used either alone or as an inner code of a concatenated coding system with the NASA standard (255, 233, 33) Reed-Solomon (RS) code as the outer code to achieve high performance (or low bit-error rate) with reduced decoding complexity. It can also be used as a component code in a multilevel bandwidth efficient coded modulation system to achieve reliable bandwidth efficient data transmission. This report will summarize the key progress we have made toward achieving our eventual goal of implementing a decoder system based upon this code. In the first phase of study, we investigated the complexities of various sectionalized trellis diagrams for the proposed (64, 40, 8) RM subcode. We found a specific 8-trellis diagram for this code which requires the least decoding complexity with a high possibility of achieving a decoding speed of 600 M bits per second (Mbps). The combination of a large number of states and a high data rate will be made possible due to the utilization of a high degree of parallelism throughout the architecture. This trellis diagram will be presented and briefly described. In the second phase of study which was carried out through the past year, we investigated circuit architectures to determine the feasibility of VLSI implementation of a high-speed Viterbi decoder based on this 8-section trellis diagram. We began to examine specific design and implementation approaches to implement a fully custom integrated circuit (IC) which will be a key building block for a decoder system implementation. The key results will be presented in this report. This report will be divided into three primary sections. First, we will briefly describe the system block diagram in which the proposed decoder is assumed to be operating and present some of the key architectural approaches being used to implement the system at high speed. Second, we will describe details of the 8-trellis diagram we found to best meet the trade-offs between chip and overall system complexity. The chosen approach implements the trellis for the (64, 40, 8) RM subcode with 32 independent sub-trellises. And third, we will describe results of our feasibility study on the implementation of such an IC chip in CMOS technology to implement one of these subtrellises.
Lin, Shu↗
Circuit Design Approaches for Implementation of a Subtrellis IC for a Reed-Muller Subcode
In his research, we have proposed the (64, 40, 8) subcode of the third-order Reed-Muller (RM) code to NASA for high-speed satellite communications. This RM subcode can be used either alone or as an inner code of a concatenated coding system with the NASA standard (255, 233, 33) Reed-Solomon (RS) code as the outer code to achieve high performance (or low bit-error rate) with reduced decoding complexity. It can also be used as a component code in a multilevel bandwidth efficient coded modulation system to achieve reliable bandwidth efficient data transmission. This report will summarize the key progress we have made toward achieving our eventual goal of implementing a decoder system based upon this code. In the first phase of study, we investigated the complexities of various sectionalized trellis diagrams for the proposed (64, 40, 8) RM subcode. We found a specific 8-trellis diagram for this code which requires the least decoding complexity with a high possibility of achieving a decoding speed of 600 M bits per second(Mbps). The combination of a large number of states and a high data rate will be made possible due to the utilization of a high degree of parallelism throughout the architecture. This trellis diagram will be presented and briefly described. In the second phase of study which was carried out through the past year, we investigated circuit architectures to determine the feasibility of VLSI implementation of a high- speed Viterbi decoder based on this 8-section trellis diagram. We began to examine specific design and implementation approaches to implement a fully custom integrated circuit (IC) which will be a key building block for a decoder system implementation. The key results will be presented in this report. This report will be divided into three primary sections. First, we will briefly describe the system block diagram in which the proposed decoder is assumed to be operating and present some of the key architectural approaches being used to implement the system at high speed. Second, we will describe details of the 8-trellis diagram we found to best meet the trade-offs between chip and overall system complexity. The chosen approach implements the trellis for the (64, 40, 8) RM subcode with 32 independent sub-trellises. And third, we will describe results of our feasibility study on the implementation of such an IC chip in CMOS technology to implement one of these subtrellises.
Lin, Shu↗
High-Speed Soft-Decision Decoding of Two Reed-Muller Codes
In his research, we have proposed the (64, 40, 8) subcode of the third-order Reed-Muller (RM) code to NASA for high-speed satellite communications. This RM subcode can be used either alone or as an inner code of a concatenated coding system with the NASA standard (255, 233, 33) Reed-Solomon (RS) code as the outer code to achieve high performance (or low bit-error rate) with reduced decoding complexity. It can also be used as a component code in a multilevel bandwidth efficient coded modulation system to achieve reliable bandwidth efficient data transmission. This report will summarize the key progress we have made toward achieving our eventual goal of implementing a decoder system based upon this code. In the first phase of study, we investigated the complexities of various sectionalized trellis diagrams for the proposed (64, 40, 8) RNI subcode. We found a specific 8-trellis diagram for this code which requires the least decoding complexity with a high possibility of achieving a decoding speed of 600 M bits per second (Mbps). The combination of a large number of states and a hi ch data rate will be made possible due to the utilization of a high degree of parallelism throughout the architecture. This trellis diagram will be presented and briefly described. In the second phase of study which was carried out through the past year, we investigated circuit architectures to determine the feasibility of VLSI implementation of a high-speed Viterbi decoder based on this 8-section trellis diagram. We began to examine specific design and implementation approaches to implement a fully custom integrated circuit (IC) which will be a key building block for a decoder system implementation. The key results will be presented in this report. This report will be divided into three primary sections. First, we will briefly describe the system block diagram in which the proposed decoder is assumed to be operating and present some of the key architectural approaches being used to implement the system at high speed. Second, we will describe details of the 8-trellis diagram we found to best meet the trade-offs between chip and overall system complexity. The chosen approach implements the trellis for the (64, 40, 8) RM subcode with 32 independent sub-trellises. And third, we will describe results of our feasibility study on the implementation of such an IC chip in CMOS technology to implement one of these sub-trellises.
Lin, Shu↗