Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATES, FLAT - STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Computation of crossing shock/turbulent boundary layer interaction at Mach 8.3

A three-dimensional (3D) hypersonic crossing shock wave/turbulent boundary-layer interaction is examined numerically at Mach 8.3. The test geometry consists of a pair of opposing sharp fins of angle alpha = 15 deg, mounted on a flat plate. Two theoretical models are evaluated. The full (3D) Reynolds-averaged Navier-Stokes equations are solved using the Baldwin-Lomax and the Rodi (modified k-epsilon) turbulence models. Computed results for both cases show good agreement with experiment for flat plate surface pressure and for flowfield profiles of pitot pressure and yaw angle, indicating that the flowfield is primarily rotational and inviscid. Fair to poor agreement is obtained for surface heat transfer, indicating a need for more accurate turbulence models. The overall flowfield structure is similar to that observed in previous crossing shock interaction studies.

Narayanswami, N.↗

Solar photochemical process engineering for production of fuels and chemicals

The engineering costs and performance of a nominal 25,000 scmd (883,000 scfd) photochemical plant to produce dihydrogen from water were studied. Two systems were considered, one based on flat-plate collector/reactors and the other on linear parabolic troughs. Engineering subsystems were specified including the collector/reactor, support hardware, field transport piping, gas compression equipment, and balance-of-plant (BOP) items. Overall plant efficiencies of 10.3 and 11.6 percent are estimated for the flat-plate and trough systems, respectively, based on assumed solar photochemical efficiencies of 12.9 and 14.6 percent. Because of the opposing effects of concentration ratio and operating temperature on efficiency, it was concluded that reactor cooling would be necessary with the trough system. Both active and passive cooling methods were considered. Capital costs and energy costs, for both concentrating and non-concentrating systems, were determined and their sensitivity to efficiency and economic parameters were analyzed. The overall plant efficiency is the single most important factor in determining the cost of the fuel.

Biddle, J. R.↗

Simulation of Blunt-Fin-Induced Shock-Wave and Turbulent Boundary-Layer Interaction

The Reynolds-averaged Navier-Stokes equations are solved numerically for supersonic flow over a blunt fin mounted on a flat plate. The fin shock causes the boundary layer to separate. which results in a complicated, three-dimensional shock-wave and boundary-layer interaction. The computed results are in good agreement with the mean static pressure measured on the fin and the flat plate. The main features, such as peak pressure on the fin leading edge and a double peak on the plate. are predicted well. The role of the horseshoe vortex is discussed. This vortex leads to the development of high-speed flow and, hence, low-pressure regions on the fin and the plate. Different thicknesses of the incoming boundary layer have been studied. Varying the thicknesses by an order of magnitude shows that the size of the horseshoe vortex and, therefore, the spatial extent of the interaction are dominated by inviscid flow and only weakly dependent on the Reynolds number. Colored graphics are used to show details of the interaction flow field.

Hung, Ching-Mao↗

Receptivity and Forced Response to Acoustic Disturbances in High-Speed Boundary Layers

Supersonic boundary-layer receptivity to freestream acoustic disturbances is investigated by solving the Navier-Stokes equations for Mach 3.5 flow over a sharp flat plate and a 7-deg half-angle cone. The freestream disturbances are generated from a wavy wall placed at the nozzle wall. The freestream acoustic disturbances radiated by the wavy wall are obtained by solving the linearized Euler equations. The results for the flat plate show that instability modes are generated at all the incident angles ranging from zero to highly oblique. However, the receptivity coefficient decreases by about 20 times when the incident angle increases from zero to a highly oblique angle of 68 degrees. The results for the cone show that no instability modes are generated when the acoustic disturbances impinge the cone obliquely. The results show that the perturbations generated inside the boundary layer by the acoustic disturbances are the response of the boundary layer to the external forcing. The amplitude of the forced disturbances inside the boundary layer are about 2.5 times larger than the incoming field for zero azimuthal wavenumber and they are about 1.5 times for large azimuthal wavenumbers.

Balakumar, P.↗

A study of real jet effects on the surface pressure distribution induced by a jet in a crossflow

A study of jet exit profile, exit Mach number, swirl and turbulence level on jet-induced loadings for jets exhausting from a surface into a crossflow is presented. The importance of each of these real jet characteristics is assessed using available data. Where adequate surface pressure distribution data are available, a correlation method to predict surface pressure for a jet exhausting from an infinite flat plate is used either to attempt to develop a correlation based on the real jet characteristics or to model the effects of that characteristic. Data comparisons are presented for selected cases. Also, a summary of information on surface pressure distribution data for jet exhausting from flat plates into a subsonic crossflow is presented.

Perkins, S. C., Jr.↗

Parametric Fin-Body and Fin-Plate Database for a Series of 12 Missile Fins

A cooperative experimental investigation has been performed to obtain a systematic fin-body and fin-plate database for a series of 12 missile fins. These data are intended to complement and extend the information contained in the Triservice missile project and to provide a systematic set of experimental data from which fin-body interference factors can be derived. Data were obtained with the fins mounted on both an axisymmetric body and on a flat plate that was used to simulate fin-alone measurements. The experiments were conducted at Mach numbers from 0.60 to 3.95; fin deflection angles of 0 deg, 10 deg, and -10 deg; and angles of attack up to 30 deg on the body and up to 95 deg on the flat plate. The data were obtained from three-component balances attached to the fins and a six-component balance located in the axisymmetric body. The data obtained in this project are documented in tabular form in this report. In addition, selected data are presented in graphical form to illustrate the effects of the test variables. These variables are configuration angle of attack; Mach number; and fin parameters of deflection angle, planform size, taper ratio, and aspect ratio. A very limited comparison with the Triservice missile data is made to illustrate the consistency between the data from these two projects.

Allen, Jerry M.↗

Nonreflecting boundary conditions for the complete unsteady transonic small-disturbance equation

Nonreflecting far-field boundary conditions that are consistent with the complete transonic small-disturbance (TSD) equations are derived. They are implemented in a new code for solving the complete TSD equation and are tested for a harmonically oscillating NACA 64A010 airfoil in transonic flow and for a flat-plate airfoil with a pulse in the angle of attack. Using the new boundary conditions on a relatively small grid, solutions for the airfoil that are obtained that agree with large-grid calculations, resulting in a 44 percent savings in computer time. Frequency responses for the flat plate show that most of the disturbances incident on the computational boundaries are absorbed by the boundary conditions.

Whitlow, W., Jr.↗

An experimental study of fluctuating pressure loads beneath swept shock/boundary-layer interactions

A database is established on the fluctuating pressure loads produced on aerodynamic surfaces beneath 3-D shock wave/boundary layer interactions. Such loads constitute a fundamental problem of critical concern to future supersonic and hypersonic flight vehicles. A turbulent boundary layer on a flat plate is subjected to interactions with swept planar shock waves generated by sharp fins. Fin angles from 5 to 25 deg at freestream Mach numbers between 2.5 and 4 produce a variety of interaction strengths from weak to very strong. Miniature Kulite pressure transducers mounted in the flat plate were used to measure interaction-induced wall pressure fluctuations. These data will be correlated with proposed new optical data on the fluctuations of the interaction structure, especially that of the lambda-shock system and its associated high-speed jet impingement.

Settles, Gary S.↗

Scale effect and optimum relations for sea surface planning

From the general dimensional and mechanical similarity theory it follows that a condition of steady motion of a given shape\bottom with constant speed on the surface of water is determined by four nondimensional parameters. By considering the various systems of independent parameters which are applied in theory and practice and special tests, there is determined their mutual relations and their suitability as planning characteristics. In studying the scale effect on the basis of the Prnndtl formula for the friction coefficient for a turbulent condition the order of magnitude is given of the error in applying the model data to full scale in the case of a single-step bottom For a bottom of complicated shape it is shown how from the test data of the hydrodynamic characteristics for one speed with various loads, or one load with various speeds, there may be obtained by simple computation with good approximation the hydrodynamic characteristics for a different speed or for a different load. (These considerations may be of use in solving certain problems on the stability of planning.) This permits extrapolating the curve of resistance against speed for large speeds inaccessible in the tank tests or for other loads which were not tested. The data obtained by computation are in good agreement with the test results. Problems regarding the optimum trim angle or the optimum width in the case of planning of a flat plate are considered from the point of view of the minimum resistance for a given load on the water and planning speeds. Formulas and graphs are given for the optimum value of the planning coefficient and the corresponding values of the trim angle and width of the flat plate.

Sedov, L.↗

Stability of separating subsonic boundary layers

The primary and subharmonic instabilities of separating compressible subsonic two-dimensional boundary layers in the presence of a two-dimensional roughness element on a flat plate are investigated. The roughness elements considered are humps and forward- and backward-facing steps. The use of cooling and suction to control these instabilities is studied. The similarities and differences between the instability characteristics of separating boundary layers and those of the boundary layer over a flat plate with a zero pressure gradient are pointed out and discussed. The theoretical results agree qualitatively and quantitatively with the experimental data of Dovgal and Kozlov. Cooling and suction decrease the growth rates of primary and subharmonic waves in the attached-flow regions but increase them in the separated-flow regions.

Masad, Jamal A.↗

Conservative force model performance for TOPEX/Poseidon precision orbit determination

The TOPEX/Poseidon spacecraft was launched on August 10, 1992 to study the Earth's oceans. To achieve maximum benefit from the altimetric data collected, mission requirements dictate that TOPEX/Poseidon's orbit must be computed at an unprecedented level of accuracy. In order to satisfy these requirements, a model which accounts for the satellite's complex geometry, attitude, and surface properties has been developed. This `box-wing' representation treats the spacecraft as the combination of flat plates arranged in the shape of a box and a connecetd solar array. The nonconservative forces acting on each of the eight surfaces are computed independently, yielding vector accelerations which are summed to compute the total aggregate effect on the satellite center-of-mass. Parameters associated with each flat plate were derived from a finite element analysis of the spacecraft. Certain parameters can be inferred from tracking data and have been adjusted to obtain a better representation of the satellite acceleration history. Changes in the nominal mission profile and the presence of an `anomalistic' force have complicated this tuning process. Model performance, parameter sensitivities, and the `anomalistic' force will be discussed.

Marshall, J. Andrew↗

Numerical simulation of crossing/turbulent boundary layer interaction at Mach 8.3 comparison of zero and two-equation turbulence models

A 3D hypersonic crossing shock wave/turbulent boundary layer interaction is examined numerically. The test geometry consists of a pair of opposing sharp fins of angle alpha = 15 deg mounted on a flat plate. The freestream Mach number is 8.28. Two theoretical models are evaluated. The full 3D Reynolds-averaged Navier-Stokes equations are solved using the Baldwin-Lomax algebraic turbulent eddy viscosity model and the Rodi turbulence model. Computed results for both cases show good agreement with experiment for flat plate surface pressure and for pitot pressure and yaw angle profiles in the flowfield. General agreement is obtained for surface flow direction. Fair to poor agreement is obtained for surface heat transfer, indicating a need for more accurate turbulence models. The overall flowfield structure is similar to that observed in previous crossing shock interaction studies.

Narayanswami, N.↗

Use of Plasma Actuators as a Moving-Wake Generator

The work documented in this report tests the concept of using plasma actuators as a simple and easy way to generate a simulated moving-wake and the disturbances associated with it in turbines. This wake is caused by the blades of the upstream stages of the turbine. Two types of devices, one constructed of arrays of NACA 0018 airfoils, and the one constructed of flat plates were studied. The airfoils or plates were equipped with surface mounted dielectric barrier discharge (DBD) plasma actuators, which were used to generate flow disturbances resembling moving-wakes. CTA hot-wire anemometry and flow visualization using a smoke-wire were used to investigate the wake independence at various spacings and downstream locations. The flat plates were found to produce better results than the airfoils in creating large velocity fluctuations in the free-stream flow. Different dielectric materials, plasma actuator locations, leading edge contours, angles of attack and plate spacings were investigated, some with positive results. The magnitudes of the velocity fluctuations were found to be comparable to existing mechanical moving-wake generators, thus proving the feasibility of using plasma actuators as a moving-wake generator.

Corke, Thomas C.↗

Photovoltaic module encapsulation design and materials selection, volume 1

Encapsulation material system requirements, material selection criteria, and the status and properties of encapsulation materials and processes available are presented. Technical and economic goals established for photovoltaic modules and encapsulation systems and their status are described. Available encapsulation technology and data are presented to facilitate design and material selection for silicon flat plate photovoltaic modules, using the best materials available and processes optimized for specific power applications and geographic sites. The operational and environmental loads that encapsulation system functional requirements and candidate design concepts and materials that are identified to have the best potential to meet the cost and performance goals for the flat plate solar array project are described. Available data on encapsulant material properties, fabrication processing, and module life and durability characteristics are presented.

Cuddihy, E.↗

Nonconservative force model parameter estimation strategy for TOPEX/Poseidon precision orbit determination

The TOPEX/Poseidon spacecraft was launched on August 10, 1992 to study the Earth's oceans. To achieve maximum benefit from the altimetric data it is to collect, mission requirements dictate that TOPEX/Poseidon's orbit must be computed at an unprecedented level of accuracy. To reach our pre-launch radial orbit accuracy goals, the mismodeling of the radiative nonconservative forces of solar radiation, Earth albedo an infrared re-radiation, and spacecraft thermal imbalances cannot produce in combination more than a 6 cm rms error over a 10 day period. Similarly, the 10-day drag modeling error cannot exceed 3 cm rms. In order to satisfy these requirements, a 'box-wing' representation of the satellite has been developed in which, the satellite is modelled as the combination of flat plates arranged in the shape of a box and a connected solar array. The radiative/thermal nonconservative forces acting on each of the eight surfaces are computed independently, yielding vector accelerations which are summed to compute the total aggregate effect on the satellite center-of-mass. Select parameters associated with the flat plates are adjusted to obtain a better representation of the satellite acceleration history. This study analyzes the estimation of these parameters from simulated TOPEX/Poseidon laser data in the presence of both nonconservative and gravity model errors. A 'best choice' of estimated parameters is derived and the ability to meet mission requirements with the 'box-wing' model evaluated.

Luthcke, S. B.↗

Source Term Model for Vortex Generator Vanes in a Navier-Stokes Computer Code

A source term model for an array of vortex generators was implemented into a non-proprietary Navier-Stokes computer code, OVERFLOW. The source term models the side force created by a vortex generator vane. The model is obtained by introducing a side force to the momentum and energy equations that can adjust its strength automatically based on the local flow. The model was tested and calibrated by comparing data from numerical simulations and experiments of a single low profile vortex generator vane on a flat plate. In addition, the model was compared to experimental data of an S-duct with 22 co-rotating, low profile vortex generators. The source term model allowed a grid reduction of about seventy percent when compared with the numerical simulations performed on a fully gridded vortex generator on a flat plate without adversely affecting the development and capture of the vortex created. The source term model was able to predict the shape and size of the stream-wise vorticity and velocity contours very well when compared with both numerical simulations and experimental data. The peak vorticity and its location were also predicted very well when compared to numerical simulations and experimental data. The circulation predicted by the source term model matches the prediction of the numerical simulation. The source term model predicted the engine fan face distortion and total pressure recovery of the S-duct with 22 co-rotating vortex generators very well. The source term model allows a researcher to quickly investigate different locations of individual or a row of vortex generators. The researcher is able to conduct a preliminary investigation with minimal grid generation and computational time.

Waithe, Kenrick A.↗

The Effect of Incoming Boundary Layer Characteristics on the Performance of a Distributed Propulsion System

An experimental study is conducted in an effort to advance the understanding of flow physics associated with a boundary layer ingesting, distributed propulsion system. The influence of incoming boundary layer thickness and flow distortions are studied on the flow downstream and the overall performance of the system. The propulsion model, fabricated using additive manufacturing and integrated with electrical fans, is mounted on a flat plate and tested at subsonic speeds. Detailed characterization of the incoming boundary layer and subsequent assessment of the downstream flow field is performed using hotwire anemometry. Modification of the incoming boundary layer is achieved by placing tripping devices, such as rods and vortex generating ramps, near the leading edge of the flat plate. The overall performance of the system for different incoming flow conditions is analyzed by comparing magnitudes of exhaust velocities as well as estimated propulsive power to the corresponding baseline values. For a constant input power to the fans, smaller upstream flow distortions and moderately thickened boundary layers result in marginal changes in the flow field downstream. On the other hand, notable reductions in downstream flow velocities and propulsive power are observed in the case of a significantly thicker and/or distorted incoming boundary layer. It is hoped that this study will serve as a database for this technologically relevant flow field that has not been explored adequately before.

Propulsion↗

A Theoretical and Experimental Study of Planing Surfaces Including Effects of Cross Section and Plan Form

A summary is given of the background and present status of the pure-planing theory for rectangular flat plates and v-bottom surfaces. The equations reviewed are compared with experiment. In order to extend the range of available planing data, the principal planing characteristics for models having sharp bottom surfaces having constant angles of dead rise of 20 degrees and 40 degrees. Planing data were also obtained for flat-plate surfaces with very slightly rounded chines for which decreased lift and drag coefficients are obtained.

Shuford, Charles L , Jr↗