Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE DISTRIBUTION - AIRFOILS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Flight measurements of lifting pressures for a thin low-aspect-ratio wing at subsonic, transonic, and low supersonic speeds

Pressure distributions in the form of differential pressure coefficients are presented for several wing chordwise and spanwise stations. Also presented are the results of limited analysis which show aircraft configuration effects, Mach number effects on the local wing loadings, comparisons of selected measured wing pressures with predicted pressures, and comparisons of wing loadings during right-turn and left-turn maneuvers.

Byrdsong, T. A.↗
NASA NTRS1985

Assessment of a 3-D boundary layer analysis to predict heat transfer and flow field in a turbine passage

An assessment was made of the applicability of a three dimensional boundary layer analysis of heat transfer, total pressure losses, and streamline flow patterns on the surfaces of both stationary and rotating turbine passages. In support of this effort, an analysis was developed to calculate a general nonorthogonal surface coordinate system for arbitrary three dimensional surfaces and also to calculate the boundary layer edge conditions for compressible flow using the surface Euler equations and experimental pressure distributions. Calculations are presented for the pressure, endwall, and suction surfaces of a stationary cascade and for the pressure surface of a rotating turbine blade. The results strongly indicate that the three dimensional boundary layer analysis can give good predictions of the flow field, loss, and heat transfer on the pressure, suction, and endwall surface of a gas turbine passage.

Anderson, O. L.↗
NASA NTRS1993

Investigation of a subsonic-arc-attachment thruster using segmented anodes

To investigate high frequency arc instabilities observed in subsonic-arc-attachment thrusters, a 3 kW, segmented-anode arcjet was designed and tested using hydrogen as the propellant. The thruster nozzle geometry was scaled from a 30 kW design previously tested in the 1960's. By observing the current to each segment and the arc voltage, it was determined that the 75-200 kHz instabilities were results of axial movements of the arc anode attachment point. The arc attachment point was fully contained in the subsonic portion of the nozzle for nearly all flow rates. The effects of isolating selected segments were investigated. In some cases, forcing the arc downstream caused the restrike to cease. Finally, decreasing the background pressure from 18 Pa to 0.05 Pa affected the pressure distribution in the nozzle, including the pressure in the subsonic arc chamber.

Berns, Darren H.↗
NASA NTRS1950

An investigation of several NACA 1-series nose inlets with and without protruding central bodies at high-subsonic Mach numbers and at a Mach number of 1.2

An investigation of three NACA 1-series nose inlets, two of which were fitted with protruded central bodies, was conducted in the Langley 8-foot high-speed tunnel. An elliptical-nose body, which had a critical Mach number approximately equal to that of one of the nose inlets, was also tested. Tests were made near zero angle of attack for a Mach number range from 0.4 to 0.925 and for the supersonic Mach number of 1.2. The inlet-velocity-ratio range extended from zero to a maximum value of 1.34. Measurements included pressure distribution, external drag, and total-pressure loss of the internal flow near the inlet. Drag was not measured for the tests at the supersonic Mach number. Over the range of inlet-velocity ratio investigated, the calculated external pressure-drag coefficient at a Mach number of 1.2 was consecutively lower for the nose inlets of higher critical Mach number, and the pressure-drag coefficient of the longest nose inlet was in the range of pressure-drag coefficient for two solid noses of fineness ratio 2.4 and 6.0. For Mach numbers below the Mach number of the supercritical drag rise, extrapolation of the test data indicated that the external drag of the nose inlets was little affected by the addition of central bodies at or slightly below the minimum inlet-velocity ratio for unseparated central-body flow. The addition of central bodies to the nose inlets also led to no appreciable effects on either the Mach number of the supercritical drag rise, or, for inlet-velocity ratios high enough to avoid a pressure peak at the inlet lip, on the critical Mach number. The total-pressure recovery of the inlets tested, which were of a subsonic type, was sensibly unimpaired at the supersonic Mach number of 1.2 Low-speed measurements of the minimum inlet-velocity ratio for unseparated central-body flow appear to be applicable for Mach numbers extending to 1.2.

Pendley, Robert E↗
NASA NTRS1993

Investigation of a subsonic-arc-attachment thruster using segmented anodes

To investigate high frequency arc instabilities observed in subsonic-arc-attachment thrusters, a 3 kW, segmented-anode arc jet was designed and tested using hydrogen as the propellant. The thruster nozzle geometry was scaled from a 30 kW design previously tested in the 1960's. By observing the current to each segment and the arc voltage, it was determined that the 75-200 kHz instabilities were results of axial movements of the arc anode attachment point. The arc attachment point was fully contained in the subsonic portion of the nozzle for nearly all flow rates. The effects of isolating selected segments were investigated. In some cases, forcing the arc downstream caused the restrike to cease. Finally, decreasing the background pressure from 18 to 0.05 Pa affected the pressure distribution in the nozzle including the pressure in the subsonic arc chamber.

Berns, Darren H.↗
NASA NTRS2016

Nano-ADEPT Aeroloads Wind Tunnel Test

A wind tunnel test of the Adaptable Deployable Entry and Placement Technology (ADEPT) was conducted in April 2015 at the US Army's 7 by10 Foot Wind Tunnel located at NASA Ames Research Center. Key geometric features of the fabric test article were a 0.7 meter deployed base diameter, a 70 degree half-angle forebody cone angle, eight ribs, and a nose-to-base radius ratio of 0.7. The primary objective of this wind tunnel test was to obtain static deflected shape and pressure distributions while varying pretension at dynamic pressures and angles of attack relevant to entry conditions at Earth, Mars, and Venus. Other objectives included obtaining aerodynamic force and moment data and determining the presence and magnitude of any dynamic aeroelastic behavior (buzz/flutter) in the fabric trailing edge. All instrumentation systems worked as planned and a rich data set was obtained. This paper describes the test articles, instrumentation systems, data products, and test results. Four notable conclusions are drawn. First, test data support adopting a pre-tension lower bound of 10 foot pounds per inch for Nano-ADEPT mission applications in order to minimize the impact of static deflection. Second, test results indicate that the fabric conditioning process needs to be reevaluated. Third, no flutter/buzz of the fabric was observed for any test condition and should also not occur at hypersonic speeds. Fourth, translating one of the gores caused ADEPT to generate lift without the need for a center of gravity offset. At hypersonic speeds, the lift generated by actuating ADEPT gores could be used for vehicle control.

system engineering↗
NASA NTRS2004

Computation of Gust-Cascade Interaction Using the CE/SE Method

The problem 2 in Category 3 of the 4th Computational Aeroacoustic(CAA) Workshop is solved using the space-time conservation element and solution element (CE/SE) method. This problem models rotor-stator interaction in a 2D cascade. It involves complex geometries and flow physics including vortex shedding and acoustic radiation. The parallel version of the 2D nonlinear Euler solver is used with an unstructured triangular mesh to solve this problem. The Giles approach is incorporated with the CE/SE method to handle non-equal pitches of the rotor and stator. Validation on the Giles approach is performed using Problem 3.1 in the 2nd CAA Workshop. The space-time CE/SE method is a finite volume method with second-order accuracy in both space and time. The flux conservation is enforced in both space and time instead of space only. It has low numerical dissipation and dispersion errors. It uses simple non-reflecting boundary conditions and is compatible with unstructured meshes. It is simple, flexible, and generate reasonably accurate solutions. The CE/SE method has been successfully applied to solve numerous practical problems, especially aeroacoustic problems. Some preliminary numerical results of the benchmark problem 3.2 of the 4th CAA Workshop are shown. The steady-state pressure contour is plotted. The mean pressure distribution on the blade surface is compared with Turbo solution showing a good agreement. The sound pressure level versus the rotor harmonic n at the six designated positions on the blade surface, three locations at inlet plane, and three locations at the outlet plane are plotted. It can be seen that the acoustic response exists only at the excitation frequencies (n = 1,2,3). On the blade surface, the acoustic wave at n = 1 is dominant, while at the inlet and outlet planes, the sound pressure level at n = 2 becomes the largest, which is similar to the results presented. The distribution of sound pressure level at different spatial modes along the z- direction is plotted for n = 1,2,3, respectively. It shows that the spatial modes m = -32 and 22 at n = 1 exponentially decay, and the spatial modes m = 10 at n = 2, m = -42 and 12 at n = 3 propagate both upstream and downstream, which agrees with the prediction based on the linearized theory. Some oscillations are observed, which needs to be investigated further. In the final paper, the numerical results will be compared with a frequency-domain solver LINFLUX solution if it is available.

Wang, X.-Y.↗
DOE OSTI2022

Microhardness Distribution of Long Magnesium Block Processed through Powder Metallurgy

Powder metallurgy is a popular method of making raw powders into specific shaped samples. However, the pressure distribution and the microhardness difference within the sample are nonnegligible and unclear when the sample is long or exceeds a specific size. In this study, the long magnesium blocks, with a ratio of about 2.8 between the sample height and the sample side length, are successfully synthesized under three uniaxial and two biaxial conditions. Then, the sample hardness values on the outer surface and the center plane are tested to study the microhardness distribution. The modified analytical expression indicates that the normal pressure exponentially decreases along the compression direction, which is consistent with the hardness distribution trend. Because higher pressure leads to a more compact arrangement of the powders, more metal bonds are formed after sintering. During the first pressing, the sidewall pressure makes the surface hardness higher. The secondary reverse compression mainly improves the bottom and core hardness due to the re-orientation and re-location of the powders. The obtained relationship between the applied pressure and the hardness distribution is instructive in predicting and improving the sample quality.

Wang, Jiaying↗
NASA NTRS1937

Empirical corrections to the span load distribution at the tip

An analysis of existing pressure-distribution data was made to determine the variation of the tip loading with wing plan form. A series of empirical tip corrections was derived that may be added to theoretical curves in certain cases to obtain a closer approach to the actual loading at the tip. The analysis indicated that the need for a tip correction decreases as either the aspect ratio or the wing taper is increased. In general, it may be said that, for wings of conventional aspect ratio, corrections to the theoretical span load curves are necessary only if the wing is tapered less than 2:1 and has a blunt tip. If the tip is well rounded in plan form, no correction appears necessary even for a wing with no taper.

Pearson, H A↗