Search NASA⌕ Search

SEARCH · Search NASA

Results for “Random fields”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Comparison of sigma/deg/ obtained from the conventional definition with sigma/deg/ appearing in the radar equation for randomly rough surfaces

Results from the radar cross section of rough surfaces calculated from a conventional definition and from a direct solution of the radar equation are compared. The purpose is to define conditions under which the conventional solution produces the same cross-section as the radar equation. A randomly rough conduction surface is considered for line sources and corrugated surfaces. Two problems are analyzed: first, a plane wave is assumed to be incident on the surface and the observed scattered fields are computed, and second, the scattered fields received by an antenna colocated with the emitting antenna are used to compute the available power. The fields are assumed to scatter incoherently and the stationary points are assumed to be homogeneously distributed over the surface. The cross sections are found to be equal if the observer is far from the surface compared to the radii of the surface at the specular points.

Levine, D. M.↗

Rapid magnetic reconnection caused by finite amplitude fluctuations

The nonlinear dynamics of the magnetohydrodynamic sheet pinch have been investigated as an unforced initial value problem for large scale Reynolds numbers up to 1000. Reconnection is triggered by adding to the sheet pinch a small but finite level of broadband random perturbations. Effects of turbulence in the solutions include the production of reconnected magnetic islands at rates that are insensitive to resistivity at early times. This is explained by noting that electric field fluctuations near the X point produce irregularities in the vector potential, sometimes taking the form of 'magnetic bubbles', which allow rapid change of field topology.

Matthaeus, W. H.↗

A noise source identification technique using an inverse Helmholtz integral equation method

A technique is developed which utilizes numerical models and field pressure information to characterize acoustic fields and identify acoustic sources. The numerical models are based on boundary element numerical procedures. Either pressure, velocity, or passive boundary conditions, in the form of impedance boundary conditions, may be imposed on the numerical model. Alternatively, if no boundary information is known, a boundary condition can be left unspecified. Field pressure data may be specified to overdetermine the numerical problem. The problem is solved numerically for the complete sound field from which the acoustic sources may be determined. The model can then be used to idenfify acoustic intensity paths in the field. The solution can be modified and the model used to evaluate design alternatives. In this investigation the method is tested analytically and verified. In addition, the sensitivity of the method to random and bias error in the input data is demonstrated.

Gardner, B. K.↗

VLF noises triggered by whistlers as observed in the topside ionosphere

ISIS-1, ISIS-2, and DE-1 VLF electric field data from Kashima station, Japan are used to investigate characteristics of whistler triggered emissions in the topside ionosphere. The occurrence rate for nonducted whistler triggered emission is shown to be distributed randomly between L = 2.0 and 4.2, while the occurrence rate of ducted whistler triggered emissions increases with latitudes between L = 1.5 and 2.9, attains a maximum at L = 2.7, and abruptly drops off at L = 3.0. The findings indicate that some whistler triggered emissions may be generated by the interaction of whistlers with magnetospheric electrons.

Nakamura, Yoshikatsu↗

The cooling rate dependence of cation distributions in CoFe2O4

The room-temperature cation distributions in bulk CoFe2O4 samples, cooled at rates between less than 0.01 and about 1000 C/sec, have been determined using Mossbauer spectroscopy in an 80-kOe magnetic field. With increasing cooling rate, the quenched structure departs increasingly from the mostly ordered cation distribution ordinarily observed at room temperature. However, the cation disorder appears to saturate just short of a random distribution at very high cooling rates. These results are interpreted in terms of a simple relaxation model of cation redistribution kinetics. The disordered cation distributions should lead to increased magnetization and decreased coercivity in CoFe2O4.

De Guire, Mark R.↗

Mitigation selection and qualification recommendations for Xilinx Virtex, Virtex-II, and Virtex-4 field programmable gate arrays

This work discusses mitigation selection and qualification techniques for Xilinx reconfigurable field programmable gate arrays (FPGAs). The aim of the paper is to provide readers with a better understanding of the engineering/reliability/project cost relationship that occurs when developing a mitigation strategy for static random access memory (SRAM)-based FPGAs.

Allen, Gregory↗

Concentration and Velocity Gradients in Fluidized Beds

In this work we focus on the height dependence of particle concentration, average velocity components, fluctuations in these velocities and, with the flow turned off, the sedimentation velocity. The latter quantities are measured using Particle Imaging Velocimetry (PIV). The PIV technique uses a 1-megapixel camera to capture two time-displaced images of particles in the bed. The depth of field of the imaging system is approximately 0.5 cm. The camera images a region with characteristic length of 2.6 cm for the small particles and 4.7 cm. for the large particles. The local direction of particle flow is determined by calculating the correlation function for sub-regions of 32 x 32 pixels. The velocity vector map is created from this correlation function using the time between images (we use 15 to 30 ms). The software is sensitive variations of 1/64th of a pixel. We produce velocity maps at various heights, each consisting of 3844 velocities. We break this map into three vertical zones for increased height information. The concentration profile is measured using an expanded (1 cm diameter) linearly polarized HeNe Laser incident on the fluidized bed. A COHU camera (gamma=1, AGC off) with a lens and a polarizer images the transmitted linearly polarized light to minimize the effects of multiply scattered light. The intensity profile (640 X 480 pixels) is well described by a Gaussian fit and the height of the Gaussian is used to characterize the concentration. This value is compared to the heights found for known concentrations. The sedimentation velocity is estimated using by imaging a region near the bottom of the bed and using PIV to measure the velocity as a function of time. With a nearly uniform concentration profile, the time can be converted to height information. The stable fluidized beds are made from large pseudo-monodisperse particles (silica spheres with radii (250-300) microns and (425-500) microns) dispersed in a glycerin/water mix. The Peclet number is sufficiently large that Brownian motion of the particles can be ignored and the Reynolds number sufficiently small that particle inertia is negligible. A packed particle bed is used to randomize and disperse the flowing fluid introduced by a peristaltic pump. The bed itself is a rectangular glass cell 8 cm wide (x), 0.8 cm deep and a height of 30.5 cm (z). The depth of field of the camera is approximately 0.5 cm so depth information is averaged. Over flow fluid is returned to the reservoir making a closed loop system. In these experiments the particles form a sediment approximately 5.7 cm high with the pump off and expand to 22 cm with the pump on. For the smaller particles the pump velocity is .5 millimeters per second and 1.1 millimeters per second for the large particles. At this concentration the bed has a very well defined top where particle concentration rapidly drops to zero.

McClymer, James P.↗

Aerodynamic prediction I

The aerodynamic prediction methodology which is needed for rotor noise calculations is presented. Airloads and wakes, dynamic stall, compressible flow, and random loads are reviewed. The aerodynamics/acoustics interface is defined when the noise or measurements are considered. The classical approach involving a distinct separation of aerodynamic sources and acoustic propagation is the basis of most rotor noise calculations. Aeroacoustics of rotors involve unique features which are not encountered in other aerodynamic problems of rotors: (1) acoustics problems ultimately require only an order of magnitude estimate of the sound pressure field, consequently remarkably good noise predictions are obtained from very simple aerodynamic analyses; (2) aeroacoustics introduce an interest in the higher frequency aerodynamics, the deterministic aerodynamic phenomena are still low frequency, however, the high frequency noise comes from the acoustic propagation; and (3) the aerodynamic phenomena on rotors that are only of interest due to the noise they produce, are the random aerodynamic pressures on the blades.

Johnson, W.↗

Simulation studies and the need for field reflectance studies

There is a need to calibrate satellite data obtained at large polar (i.e., off-nadir) view angles for effects caused by scanner geometry and by the atmosphere. If such effects are not corrected for, then recorded radiance data will contain systematic and random errors which will make accurate target identification and quantification difficult. Adequate calibration of digital radiance data requires both an inductive analysis of digital satellite images and a deductive analysis based upon a priori simulation studies. The inputs to a simulation model (ground reflectance, atmospheric transmission and bandscatter) and their variability are dependent upon (for example) sun-target-sensor geometry. There is a major need to make accurate ground reflectance measurements to provide calibration information on the anisotropy of ground reflectance. There is also a need to assess atmospheric transmission and backscatter from the image itself. A potential simple, inexpensive method for making ground reflectance measurements in the above context is discussed.

Duggin, M. J.↗

Thundercloud radio emission from cosmic-ray-shower ionization electrons

The drift of shower ionization electrons in thundercloud fields constitutes a traveling current pulse whose amplitude is modulated by shower development and by the thundercloud field. The radio emission from such a pulse is calculated for a simple modulation model. The response of electric dipole antennas to such pulses is evaluated. To distinguish shower ionization radio pulses from random noise, the use of two receiver bands centered at a common frequency is proposed. It is shown that the ratio of the power in the two bands can be used to distinguish shower ionization radio signals from random noise. For modulated current pulses traveling above the speed of light in a medium, an inverse modulation effect is found. For unmodulated current pulses traveling above the speed of light in a medium, a new class of realizations of the Cerenkov effect is discovered.

Tompkins, D. R., Jr.↗

Random vortex method for combusting flows

The random vortex method (RVM) of Chorin was developed by the recirculating flows. The RVM method models turbulence from first principles, tracking the vorticity and obtaining the interaction of vorticity with the bulk flow field. A computer program was produced called MIMOC, Modeling the Interface Motion of Combustion, which can be used to calculate the reacting flow field behind a rearward facing step. Several comparisons between experimental data and calculations were made. The RVM methood computes qualitatively good results, but the quantitative agreement as yet is not completely satisfactory. Much of the difficulty may be caused by the treatment of boundary conditions and the techniques used for obtaining statistical averages of velocities and turbulence quantities. For the rearward facing step the computed reattachment length equals the experimental value. However, the reverse velocity in the recirculation zone is over predicted by 300 percent. In the calculations, a uniform entrance velocity was assumed with no boundary layer at the step lip. This high velocity may be overdriving the reverse flow region.

Marek, C. J.↗

Virtual and Experimental Visualization of Flows in Packed Beds of Spheres Simulating Porous Media Flows

A videotape presentation of flow in a packed bed of spheres is provided. The flow experiment consisted of three principal elements: (1) an oil tunnel 76.2 mm by 76.2 mm in cross section, (2) a packed bed of spheres in regular and irregular arrays, and (3) a flow characterization methodology, either (a) full flow field tracking (FFFT) or (b) computational fluid dynamic (CFD) simulation. The refraction indices of the oil and the test array of spheres were closely matched, and the flow was seeded with aluminum oxide particles. Planar laser light provided a two-dimensional projection of the flow field, and a traverse simulated a three-dimensional image of the entire flow field. Light focusing and reflection rendered the spheres black, permitting visualization of the planar circular interfaces in both the axial and transverse directions. Flows were observed near the wall-sphere interface and within the set of spheres. The CFD model required that a representative section of a packed bed be formed and gridded, enclosing and cutting six spheres so that symmetry conditions could be imposed at all cross-boundaries. Simulations had to be made with the flow direction at right angles to that used in the experiments, however, to take advantage of flow symmetry. Careful attention to detail was required for proper gridding. The flow field was three-dimensional and complex to describe, yet the most prominent finding was flow threads, as computed in the representative 'cube' of spheres with face symmetry and conclusively demonstrated experimentally herein. Random packing and bed voids tended to disrupt the laminar flow, creating vortices.

Hendricks, R. C.↗

Effect of Alignment on Transport Properties of Carbon Nanotube/Metallic Junctions

Ballistic and spin coherent transport in single walled carbon nanotubes (SWCNT) are predicted to enable high sensitivity single-nanotube devices for strain and magnetic field sensing. Based upon these phenomena, electron beam lithography procedures have been developed to study the transport properties of purified HiPCO single walled carbon nanotubes for development into sensory materials for nondestructive evaluation. Purified nanotubes are dispersed in solvent suspension and then deposited on the device substrate before metallic contacts are defined and deposited through electron beam lithography. This procedure produces randomly dispersed ropes, typically 2 - 20 nm in diameter, of single walled carbon nanotubes. Transport and scanning probe microscopy studies have shown a good correlation between the junction resistance and tube density, alignment, and contact quality. In order to improve transport properties of the junctions a technique has been developed to align and concentrate nanotubes at specific locations on the substrate surface. Lithographic techniques are used to define local areas where high frequency electric fields are to be concentrated. Application of the fields while the substrate is exposed to nanotube-containing solution results in nanotube arrays aligned with the electric field lines. A second electron beam lithography layer is then used to deposit metallic contacts across the aligned tubes. Experimental measurements are presented showing the increased tube alignment and improvement in the transport properties of the junctions.

Wincheski, Buzz↗

Event-Driven Random-Access-Windowing CCD Imaging System

A charge-coupled-device (CCD) based high-speed imaging system, called a realtime, event-driven (RARE) camera, is undergoing development. This camera is capable of readout from multiple subwindows [also known as regions of interest (ROIs)] within the CCD field of view. Both the sizes and the locations of the ROIs can be controlled in real time and can be changed at the camera frame rate. The predecessor of this camera was described in High-Frame-Rate CCD Camera Having Subwindow Capability (NPO- 30564) NASA Tech Briefs, Vol. 26, No. 12 (December 2002), page 26. The architecture of the prior camera requires tight coupling between camera control logic and an external host computer that provides commands for camera operation and processes pixels from the camera. This tight coupling limits the attainable frame rate and functionality of the camera. The design of the present camera loosens this coupling to increase the achievable frame rate and functionality. From a host computer perspective, the readout operation in the prior camera was defined on a per-line basis; in this camera, it is defined on a per-ROI basis. In addition, the camera includes internal timing circuitry. This combination of features enables real-time, event-driven operation for adaptive control of the camera. Hence, this camera is well suited for applications requiring autonomous control of multiple ROIs to track multiple targets moving throughout the CCD field of view. Additionally, by eliminating the need for control intervention by the host computer during the pixel readout, the present design reduces ROI-readout times to attain higher frame rates. This camera (see figure) includes an imager card consisting of a commercial CCD imager and two signal-processor chips. The imager card converts transistor/ transistor-logic (TTL)-level signals from a field programmable gate array (FPGA) controller card. These signals are transmitted to the imager card via a low-voltage differential signaling (LVDS) cable assembly. The FPGA controller card is connected to the host computer via a standard peripheral component interface (PCI).

Monacos, Steve↗

Velocity and Temperature Measurement in Supersonic Free Jets Using Spectrally Resolved Rayleigh Scattering

The flow fields of unheated, supersonic free jets from convergent and convergent-divergent nozzles operating at M = 0.99, 1.4, and 1.6 were measured using spectrally resolved Rayleigh scattering technique. The axial component of velocity and temperature data as well as density data obtained from a previous experiment are presented in a systematic way with the goal of producing a database useful for validating computational fluid dynamics codes. The Rayleigh scattering process from air molecules provides a fundamental means of measuring flow properties in a non-intrusive, particle free manner. In the spectrally resolved application, laser light scattered by the air molecules is collected and analyzed using a Fabry-Perot interferometer (FPI). The difference between the incident laser frequency and the peak of the Rayleigh spectrum provides a measure of gas velocity. The temperature is measured from the spectral broadening caused by the random thermal motion and density is measured from the total light intensity. The present point measurement technique uses a CW laser, a scanning FPI and photon counting electronics. The 1 mm long probe volume is moved from point to point to survey the flow fields. Additional arrangements were made to remove particles from the main as well as the entrained flow and to isolate FPI from the high sound and vibration levels produced by the supersonic jets. In general, velocity is measured within +/- 10 m/s accuracy and temperature within +/- 10 K accuracy.

Panda, J.↗

The uncertainty threshold principle - Fundamental limitations of optimal decision making under dynamic uncertainty

The fundamental limitations of the optimal control of dynamic systems with random parameters are analyzed by studying a scalar linear-quadratic optimal control example. It is demonstrated that optimum long-range decision making is possible only if the dynamic uncertainty (quantified by the means and covariances of the random parameters) is below a certain threshold. If this threshold is exceeded, there do not exist optimum decision rules. This phenomenon is called the 'uncertainty threshold principle'. The implications of this phenomenon to the field of modelling, identification, and adaptive control are discussed.

Athans, M.↗

Electromagnetic scattering theory

Electromagnetic scattering theory is discussed with emphasis on the general stochastic variational principle (SVP) and its applications. The stochastic version of the Schwinger-type variational principle is presented, and explicit expressions for its integrals are considered. Results are summarized for scalar wave scattering from a classic rough-surface model and for vector wave scattering from a random dielectric-body model. Also considered are the selection of trial functions and the variational improvement of the Kirchhoff short-wave approximation appropriate to large size-parameters. Other applications of vector field theory discussed include a general vision theory and the analysis of hydromagnetism induced by ocean motion across the geomagnetic field. Levitational force-torque in the magnetic suspension of the disturbance compensation system (DISCOS), now deployed in NOVA satellites, is also analyzed using the developed theory.

Bird, J. F.↗

Effects of electromagnetic wave interference on observations of the Earth radiation budget

This paper investigates conditions necessary to match the irradiance derived by integrating radiances measured by a narrow field of view scanning radiometer with the irradiance measured by a hemispherical radiometer, both placed at a satellite altitude for Earth radiation budget estimates. When all sources are similar and they are spatially distributed randomly, then integrating radiance for the irradiance does not introduce a bias. Although the exact magnitude of the bias in other conditions is unknown, a finite area of the aperture that is much larger than the coherence area of radiation contributing to the Earth radiation budget, and a finite time to take a single measurement that is longer than the coherence time are likely to make the difference of the irradiance integrated from radiances and the irradiance measured by a hemispherical instrument insignificant. This conclusion does not contradict the existence of spatial coherence of light from incoherent sources. Therefore, electromagnetic energy absorbed by Earth is derivable from radiances measured by a scanning radiometer integrated over the Earth-viewing hemisphere and then averaging across all locations on the satellite orbital sphere when combined with solar irradiance measurements. Comparisons made in earlier studies show that the difference is less than 1%. In addition, when surface irradiances computed by a radiative transfer model constrained by top-of-atmosphere irradiances derived from radiance measurements are compared with downward shortwave irradiances taken by combinations of a pyreheliometer and a shaded pyranometer, or pyranometers, and with longwave ir- radiances taken by pyrgeometers, the biases in monthly mean irradiances are less than the uncertainties in the surface observations.

Seiji Kato↗