Search NASA⌕ Search

SEARCH · Search NASA

Results for “Simulation Use Case”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

TU-C-BRE-04: 3D Gel Dosimetry Using ViewRay On-Board MR Scanner: A Feasibility Study

Purpose: MR based 3D gel has been proposed for radiation therapy dosimetry. However, access to MR scanner has been one of the limiting factors for its wide acceptance. Recent commercialization of an on-board MR-IGRT device (ViewRay) may render the availability issue less of a concern. This work reports our attempts to simulate MR based dose measurement accuracy on ViewRay using three different gels. Methods: A spherical BANG gel dosimeter was purchased from MGS Research. Cylindrical MAGIC gel and Fricke gel were fabricated in-house according to published recipes. After irradiation, BANG and MAGIC were imaged using a dual-echo spin echo sequence for T2 measurement on a Philips 1.5T MR scanner, while Fricke gel was imaged using multiple spin echo sequences. Difference between MR measured and TPS calculated dose was defined as noise. The noise power spectrum was calculated and then simulated for the 0.35 T magnetic field associated with ViewRay. The estimated noise was then added to TG-119 test cases to simulate measured dose distributions. Simulated measurements were evaluated against TPS calculated doses using gamma analysis. Results: Given same gel, sequence and coil setup, with a FOV of 180×90×90 mm3, resolution of 3×3×3 mm3, and scanning time of 30 minutes, the simulated measured dose distribution using BANG would have a gamma passing rate greater than 90% (3%/3mm and absolute). With a FOV 180×90×90 mm3, resolution of 4×4×5 mm3, and scanning time of 45 minutes, the simulated measuremened dose distribution would have a gamma passing rate greater than 97%. MAGIC exhibited similar performance while Fricke gel was inferior due to much higher noise. Conclusions: The simulation results demonstrated that it may be feasible to use MAGIC and BANG gels for 3D dose verification using ViewRay low-field on-board MRI scanner.

60 APPLIED LIFE SCIENCES↗

ISSARS Aerosol Database : an Incorporation of Atmospheric Particles into a Universal Tool to Simulate Remote Sensing Instruments

The Instrument Simulator Suite for Atmospheric Remote Sensing (ISSARS) entered its third and final year of development with an overall goal of providing a unified tool to simulate active and passive space borne atmospheric remote sensing instruments. These simulations focus on the atmosphere ranging from UV to microwaves. ISSARS handles all assumptions and uses various models on scattering and microphysics to fill the gaps left unspecified by the atmospheric models to create each instrument's measurements. This will help benefit mission design and reduce mission cost, create efficient implementation of multi-instrument/platform Observing System Simulation Experiments (OSSE), and improve existing models as well as new advanced models in development. In this effort, various aerosol particles are incorporated into the system, and a simulation of input wavelength and spectral refractive indices related to each spherical test particle(s) generate its scattering properties and phase functions. These atmospheric particles being integrated into the system comprise the ones observed by the Multi-angle Imaging SpectroRadiometer(MISR) and by the Multiangle SpectroPolarimetric Imager(MSPI). In addition, a complex scattering database generated by Prof. Ping Yang (Texas A&M) is also incorporated into this aerosol database. Future development with a radiative transfer code will generate a series of results that can be validated with results obtained by the MISR and MSPI instruments; nevertheless, test cases are simulated to determine the validity of various plugin libraries used to determine or gather the scattering properties of particles studied by MISR and MSPI, or within the Single-scattering properties of tri-axial ellipsoidal mineral dust particles database created by Prof. Ping Yang.

Instrument Simulator Suite for Atmospheric Remote ↗

Generating a Grid for Unstructured RANS Simulations of Jet Flows

A study has been performed to determine best practices for generating unstructured grids for Reynolds-Averaged Navier-Stokes (RANS) simulations of jet flows. The Axisymmetric Near-Sonic Jet Case from the Turbulence Modeling Resource was used for this study: a Mach 0.985 flow through the 2-in. diameter Acoustic Reference Nozzle (ARN2). Simulations were run with FUN3D and used the Menter Shear Stress Transport (SST-V), Spalart-Allmaras (S-A), and k-kL turbulence models. The axial velocity and turbulent kinetic energy fields in the jet plume of the unstructured grid solutions were compared to those of the baseline structured grid solution provided by the Turbulence Modeling Resource. Only solutions using grids with structured-like elements in the jet plume showed good agreement with the baseline structured grid solution. Using the SST-V turbulence model, the fully unstructured grid solutions predicted the jet potential core to decay upstream of the baseline solution. With the S-A turbulence model, the unstructured grid solutions predicted the jet potential core to decay upstream of the baseline solution. The solutions using the k-kL turbulence model seemed less sensitive to grid topology. Nozzle massflow and thrust performance were also compared for all simulations. Based on the results of this study, it is currently recommended that structured-like grid elements are used in the plumes of jet flows; unstructured grid elements can be used elsewhere.

RANS Simulations; Unstructured Grids; Jet Flows↗

Entry Abort Determination Using Non-Adaptive Neural Networks for Mars Precision Landers

The 2009 Mars Science Laboratory (MSL) will attempt the first precision landing on Mars using a modified version of the Apollo Earth entry guidance program. The guidance routine, Entry Terminal Point Controller (ETPC), commands the deployment of a supersonic parachute after converging the range to the landing target. For very dispersed cases, ETPC may not converge the range to the target and safely command parachute deployment within Mach number and dynamic pressure constraints. A full-lift up abort can save 85% of these failed trajectories while abandoning the precision landing objective. Though current MSL requirements do not call for an abort capability, an autonomous abort capability may be desired, for this mission or future Mars precision landers, to make the vehicle more robust. The application of artificial neural networks (NNs) as an abort determination technique was evaluated by personnel at the National Aeronautics and Space Administration (NASA) Johnson Space Center (JSC). In order to implement an abort, a failed trajectory needs to be recognized in real time. Abort determination is dependent upon several trajectory parameters whose relationships to vehicle survival are not well understood, and yet the lander must be trained to recognize unsafe situations. Artificial neural networks (NNs) provide a way to model these parameters and can provide MSL with the artificial intelligence necessary to independently declare an abort. Using the 2009 Mars Science Laboratory (MSL) mission as a case study, a non-adaptive NN was designed, trained and tested using Monte Carlo simulations of MSL descent and incorporated into ETPC. Neural network theory, the development history of the MSL NN, and initial testing with severe dust storm entry trajectory cases are discussed in Reference 1 and will not be repeated here. That analysis demonstrated that NNs are capable of recognizing failed descent trajectories and can significantly increase the survivability of MSL for very dispersed cases. NN testing was then broadened to evaluate fully dispersed entry trajectories. The NN correctly classified 99.7% of descent trajectories as abort or nonabort and reduced the probability of an unsafe parachute deployment by 83%. This second, broader testing phase is discussed in this paper.

Graybeal, Sarah R.↗

Immersive Digital Twins and Decision Making

This work focuses on developing and implementing immersive digital twins to support decision-making processes in construction automation and energy simulation analysis. The use of digital twins enables users to explore and interact with virtual replicas of physical systems, providing a unique and valuable perspective for problem-solving. In the context of construction automation, we present two case studies that integrate immersive visualization and worker-machine interaction. In the context of energy simulation analysis using digital twins, we describe our digital twin framework that combines interactive visualization with machine learning techniques to approximate computationally expensive simulations, allowing for faster and more efficient analysis of complex energy systems. Through these research endeavors, we demonstrate the potential of immersive digital twins in decision-making across various domains.

digital twins↗

The Production of Cold Gas Within Galaxy Outflows

I present a suite of three-dimensional simulations of the evolution of initially hot material ejected by starburst-driven galaxy outflows. The simulations are conducted in a comoving frame that moves with the material, tracking atomic/ionic cooling, Compton cooling, and dust cooling and destruction. Compton cooling is the most efficient of these processes, while the main role of atomic/ionic cooling is to enhance density inhomogeneities. Dust, on the other hand, has little effect on the outflow evolution, and is rapidly destroyed in all the simulations except for the case with the smallest mass flux. I use the results to construct a simple steady-state model of the observed UV/optical emission from each outflow. The velocity profiles in this case are dominated by geometric effects, and the overall luminosities are extremely strong functions of the properties of the host system, as observed in ultra-luminous infrared galaxies (ULIRGs). Furthermore the luminosities and maximum velocities in several models are consistent with emission-line observations of ULIRGs, although the velocities are significantly greater than observed in absorption-line studies. It may be that absorption line observations of galaxy outflows probe entrained cold material at small radii, while emission-line observations probe cold material condensing from the initially hot medium at larger distances.

79 ASTRONOMY AND ASTROPHYSICS↗

Nonlinear Reduced-Order Simulation Using An Experimentally Guided Modal Basis

A procedure is developed for using nonlinear experimental response data to guide the modal basis selection in a nonlinear reduced-order simulation. The procedure entails using nonlinear acceleration response data to first identify proper orthogonal modes. Special consideration is given to cases in which some of the desired response data is unavailable. Bases consisting of linear normal modes are then selected to best represent the experimentally determined transverse proper orthogonal modes and either experimentally determined inplane proper orthogonal modes or the special case of numerically computed in-plane companions. The bases are subsequently used in nonlinear modal reduction and dynamic response simulations. The experimental data used in this work is simulated to allow some practical considerations, such as the availability of in-plane response data and non-idealized test conditions, to be explored. Comparisons of the nonlinear reduced-order simulations are made with the surrogate experimental data to demonstrate the effectiveness of the approach.

Rizzi, Stephen A.↗

SU-F-T-682: In-Vivo Simulation of the Relative Biological Effectiveness in Proton Therapy Using a Monte Carlo Method

Purpose: In proton therapy, the relative biological effectiveness (RBE) – compared with conventional photon therapy – is routinely set to 1.1. However, experimental in vitro studies indicate evidence for the variability of the RBE. To clarify the impact on patient treatment, investigation of the RBE in a preclinical case study should be performed. Methods: The Monte Carlo software TOPAS was used to simulate the radiation field of an irradiation setup at the experimental beamline of the proton therapy facility (OncoRay) in Dresden, Germany. Simulations were performed on cone beam CT-data (CBCT) of a xenogeneous mouse with an orthotopic lung carcinoma obtained by an in-house developed small animal image-guided radiotherapy device. A homogeneous physical fraction dose of 1.8Gy was prescribed for the contoured tumor volume. Simulated dose and linear energy transfer distributions were used to estimate RBE values in the mouse based on an RBE model by Wedenberg et al. To characterize radiation sensitivity of normal and tumor tissue, α/β-ratios were taken from the literature for NB1RGB (10.1Gy) and human squamous lung cancer (6.2Gy) cell lines, respectively. Results: Good dose coverage of the target volume was achieved with a spread-out Bragg peak (SOBP). The contra-lateral lung was completely spared from receiving radiation. An increase in RBE towards the distal end of the SOBP from 1.07 to 1.35 and from 1.05 to 1.3 was observed when considering normal tissue and tumor, respectively, with the highest RBE values located distal to the target volume. Conclusion: Modeled RBE values simulated on CBCT for experimental preclinical proton therapy varied with tissue type and depth in a mouse and differed therefore from a constant value of 1.1. Further translational work will include, first, conducting preclinical experiments and, second, analogous RBE studies in patients using experimentally verified simulation settings for our clinically used patient-specific beam conforming technique.

60 APPLIED LIFE SCIENCES↗

Test and evaluation of the generalized gate logic system simulator

The results of the initial testing of the Generalized Gate Level Logic Simulator (GGLOSS) are discussed. The simulator is a special purpose fault simulator designed to assist in the analysis of the effects of random hardware failures on fault tolerant digital computer systems. The testing of the simulator covers two main areas. First, the simulation results are compared with data obtained by monitoring the behavior of hardware. The circuit used for these comparisons is an incomplete microprocessor design based upon the MIL-STD-1750A Instruction Set Architecture. In the second area of testing, current simulation results are compared with experimental data obtained using precursors of the current tool. In each case, a portion of the earlier experiment is confirmed. The new results are then viewed from a different perspective in order to evaluate the usefulness of this simulation strategy.

Miner, Paul S.↗

Recent Advances to Estimation of Fixed-Interface Modal Models Using Dynamic Substructuring

In 2010, Allen & Mayes proposed to estimate the fixed-interface modes of a structure by measuring the modes of the structure bolted to a fixture and then applying constraints to the fixture using the transmission simulator method. While the method proved useful, and has indeed been used in studies since that point, a few peculiarities were noted. First, in some cases the estimated fixed-base natural frequencies were observed to converge very slowly to the true values (in simulated experiments) as the number of constraints was increased. To formulate these constraints, prior studies used only the free-interface modes of the fixture or the measured modes of the assembly. This work extends that to consider other sets of constraints, showing improved results. Furthermore, in some prior studies it has been observed that there were errors of more than 10% in the natural frequencies even when the fixture motion was hundreds of times smaller than the motion of the structure of interest (and so it had presumably been removed). This work explores this phenomenon, seeking to use the strain energy in the fixture, to the extent that it can be estimated using a test-analysis model for the fixture, as a metric to predict frequency error. The proposed methods are explored by applying them to simulated measurements from a beam and from the NASA Space Launch System coupled to the Mobile Launcher.

Allen, Mathew S.↗

Co-simulation of innovative integrated HVAC systems in buildings

Integrated performance simulation of buildings HVAC systems can help in reducing energy consumption and increasing occupant comfort. However, no single building performance simulation (BPS) tool offers sufficient capabilities and flexibilities to analyze integrated building systems and to enable rapid prototyping of innovative building and system technologies. One way to alleviate this problem is to use co-simulation, as an integrated approach to simulation. This article elaborates on issues important for co-simulation realization and discusses multiple possibilities to justify the particular approach implemented in the here described co-simulation prototype. The prototype is validated with the results obtained from the traditional simulation approach. It is further used in a proof-of-concept case study to demonstrate the applicability of the method and to highlight its benefits. Stability and accuracy of different coupling strategies are analyzed to give a guideline for the required coupling time step.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Simulation benchmarks for low-pressure plasmas: Capacitive discharges

Benchmarking is generally accepted as an important element in demonstrating the correctness of computer simulations. In the modern sense, a benchmark is a computer simulation result that has evidence of correctness, is accompanied by estimates of relevant errors, and which can thus be used as a basis for judging the accuracy and efficiency of other codes. In this paper, we present four benchmark cases related to capacitively coupled discharges. These benchmarks prescribe all relevant physical and numerical parameters. We have simulated the benchmark conditions using five independently developed particle-in-cell codes. We show that the results of these simulations are statistically indistinguishable, within bounds of uncertainty that we define. We, therefore, claim that the results of these simulations represent strong benchmarks, which can be used as a basis for evaluating the accuracy of other codes. These other codes could include other approaches than particle-in-cell simulations, where benchmarking could examine not just implementation accuracy and efficiency, but also the fidelity of different physical models, such as moment or hybrid models. We discuss an example of this kind in the Appendix. Of course, the methodology that we have developed can also be readily extended to a suite of benchmarks with coverage of a wider range of physical and chemical phenomena.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effects of Cloud Liquid-Phase Microphysical Processes in Mixed-Phase Cumuli Over the Tibetan Plateau

Numerical simulations often overpredict precipitation over the Tibetan Plateau (TP). To examine the factors causing precipitation overprediction, different parameterizations of liquid-phase microphysical processes (accretion, autoconversion, and entrainment-mixing) are implemented into the Morrison microphysics scheme to simulate a TP precipitation event in summer with the Weather Research and Forecasting (WRF) model. The general spatial distribution and temporal trend of precipitation are captured by all simulations, but the precipitation rate is overpredicted. The results from sensitivity experiments suggest that compared to other examined liquid-phase processes, the accretion process is more important in precipitation simulation over the TP region. Further investigation with the Heidke skill scores reveals that accretion parameterization that takes into account the raindrop size produces the most accurate results in terms of the total surface precipitation. This parameterization suppresses spurious accretion and does not produce liquid-phase precipitation until cloud droplets are big enough. Here, it is also confirmed that increasing the model resolution can reduce precipitation overprediction. Results from the case study are confirmed by the use of a one-month simulation.

54 ENVIRONMENTAL SCIENCES↗

An Open-Source Virtual Testbed for a Real Net-Zero Energy Community

Net zero energy communities (NZECs) are critical to ensure sustainability and resilience of modernized power systems. System modeling helps overcome technical challenges in designing and operating NZECs. In this paper, we present the modeling work based on a real NZEC. Two sets of models are developed: higher-fidelity physics-based models considering the interaction between subsystems of the studied NZEC and capturing fast-dynamics; and lower-fidelity data-driven models requiring less resource to establish and/or run. All models are validated against measurements from this real NZEC. In addition, we create a simulation framework which streamlines the processes for simulation and thus allows using developed models to form a virtual testbed. To demonstrate the usage of the virtual testbed, a case study is conducted where a building-to-grid integration control is evaluated via simulation. The evaluation results suggest that the tested control significantly smooths the power draw of the studied community and doesn’t sacrifice the thermal comfort to a great extent.

Huang, Sen↗

A Blockchain Case Study for Urban Air Mobility Operational Intent

To realize the potential of Urban Air Mobility (UAM), an assurance of cybersecurity is critical for public acceptance. UAM is a concept that proposes to develop short-range, point-to-point transportation systems in metropolitan areas using vertical takeoff and landing (VTOL) aircraft to overcome increasing surface congestion. The growth in the development of UAM systems, and the associated data exchange and service interactions will be at risk due to numerous types of cybersecurity attacks. The intent of this work is to leverage a permissioned blockchain to simulate secure data exchange and storage for the UAM operational intent use case. In this case study, two vehicle operators are operating in the same airspace. Their intent is to fly vehicles that land at a shared vertiport, securely.

Urban Air Mobility↗

A Blockchain Case Study for Urban Air Mobility Operational Intent

To realize the potential of Urban Air Mobility (UAM), an assurance of cybersecurity is critical for public acceptance. UAM is a concept that proposes to develop short-range, point-to-point transportation systems in metropolitan areas using vertical takeoff and landing (VTOL) aircraft to overcome increasing surface congestion. The growth in the development of UAM systems, and the associated data exchange and service interactions will be at risk due to numerous types of cybersecurity attacks. The intent of this work is to leverage a permissioned blockchain to simulate secure data exchange and storage for the UAM operational intent use case.

UAM↗

A Blockchain Case Study for Urban Air Mobility Operational Intent

To realize the potential of Urban Air Mobility (UAM), an assurance of cybersecurity is critical for public acceptance. UAM is a concept that proposes to develop short-range, point-to-point transportation systems in metropolitan areas using vertical takeoff and landing (VTOL) aircraft to overcome increasing surface congestion. The growth in the development of UAM systems, and the associated data exchange and service interactions will be at risk due to numerous types of cybersecurity attacks. The intent of this work is to leverage a permissioned blockchain to simulate secure data exchange and storage for the UAM operational intent use case.

UAM↗

A bespoke model of Arctic river basins based on hillslope delineation: Model Archive

This dataset is a model archive of the paper A bespoke model of Arctic river basins based on hillslope delineation (in prep), which introduces a watershed decomposition and parameterization method for large scale permafrost hydrology simulation. With this dataset, this study aims to address the research question: whether a computationally efficient hillslope-based modeling framework can reliably simulate discharge at Arctic river-basin scales. This dataset contains model input and output data for five modeling scenarios at a study site located in the Sagavanirktok River basin. The five modeling scenarios include three modeling cases under temperate conditions using full 3D, decomposed 3D, and decomposed 2D modeling strategies; and two modeling cases under actual Arctic conditions with permafrost using full 3D and decomposed 2D modeling strategies. Simulations were performed using the Advanced Terrestrial Simulator (ATS, v1.6 for three temperate scenarios and v1.5 for two Arctic scenarios), a physics-rich integrated surface–subsurface hydrologic model with cryo-hydrology features. For the three temperate models, simulations were conducted for the period of 10/01/1993 - 09/30/2002; and for the two Arctic models, simulations were conducted for the period of 01/01/1994 - 12/31/2002. To facilitate reproducibility of simulations, all datasets are organized hierarchically. The dataset contains: (1) Mesh files (.exo) for full 3D model, decomposed 3D models, and decomposed 2D models, located in huc/190604020802_gauge15906000/mesh/. Mesh files can be visualized through Paraview or read by Python. (2) Climate forcings (.h5) for full 3D model and decomposed 3D/2D models are located in huc/190604020802_gauge15906000/daymet_onePiece/, and huc/190604020802_gauge15906000/vp_pr_revised_daymet_1980_2006_with_wind/ separately. Accessible by Python. (3) Raw measured gage discharge (.csv) from USGS, located in huc/190604020802_gauge15906000/gaged_basin15906000_discharge_usgs/. Accessible by Python. (4) Delineated subdomain raster (.tif) and shape files (.shp), and the final parameterized results (.npy) for decomposed models, located in huc/190604020802_gauge15906000/data_preprocessed-meshing. Accessible by Python. (5) Temperate models are located in nonpermaf_huc190604020802_gauge15906000/, which includes three cases: decomposed 2D models (inside model_0*-hillslope_*), decomposed 3D models (inside model_1*-subcatchment_*), and full 3D model (inside model_2*-onepiece_*). Two step spin-up results (checkpoint_final.h5) are located in model_*1-*_spinup_steadystate and model_*2-*_spinup_cycle, separately, which are used to initialize real transient models. The input files (.xml) and output results (.dat) of the real transient models are located in model_*3-*_transient/. Especially, for two example hillslope models (ID=-11 and 11), additional h5py files are included in model_03-hillslope_transient/hillslope-11/, model_03-hillslope_transient/hillslope11, model_13-subcatchment_transient/subcatchment-11/, model_13-subcatchment_transient/subcatchment/11, respectively, which are used to plot the saturation figure (Figure 5) in the manuscript. Accessible by Python. (6) Arctic models are located in huc190604020802_gauge15906000/, which includes two cases: decomposed 2D models (inside model_04-hillslope_transient), and full 3D model (inside model_05-onepiece_transient_mannp1_ra). Three step spin-up results (checkpoint_final.h5) are located in model_01-column_freezeup/, model_02-column_spinup/, model_03-hillslope_spinup/, respectively, which are used to initialize real 2D transient hillslope models. The input files (.xml) and output results (.dat) of transient 2D hillslope models are located in model_04-hillslope_transient/. The input files (.xml) and output results (.dat) of the full 3D transient model is located in model_05-onepiece_transient_mannp1_ra/. The full 3D transient model is initialized by model_02-column_spinup/. Accessible by Python. (7) The MOSART routed discharge results (.csv) under Arctic conditions is located in huc190604020802_gauge15906000/MOSART/. Accessible by Python. (8) All Python codes (.py) used to parameterize full 3D model to decomposed 2D models are located in script/. These codes fit with watershed workflow (a watershed delineation tool) v1.4 under the branch gaob/v1.4 from https://github.com/gaobhub/watershed-workflow.git.

EARTH SCIENCE > CRYOSPHERE↗