Search NASA⌕ Search

SEARCH · Search NASA

Results for “cathode utilization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

801 records · Page 45
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Phase Field Modeling of Corrosion for Design of Next-Generation Magnesium-Aluminum Vehicle Joints

In this study, WPI and its partners sought to understand galvanic corrosion in Mg-Al friction stir weld (FSW) joints. Unlike fusion welds, FSW is done in the solid state. This limits (but does not eliminate) the formation of brittle Al-Mg intermetallics, resulting in better joint strength and corrosion resistance. This study aimed to understand corrosion behavior of Mg-Al FSW joints by using a Cahn-Hilliard phase field electrochemistry model based on the work of Pongsaksawad et al. Its context challenge problem was an ultra-light door designed by Magna with 6061-Al sheet outer and ZEK100-Mg sheet inner panels, joined by an adhesive and FSW. Unlike most FSW joints, which weld through the softer material into the harder one, the Al sheet’s hem joint around Mg required the FSW tool to through the harder Al into the softer Mg, which was itself a challenge. Despite this challenge, PNNL succeeded in consistently making very strong FSW lap joints, by using a triflute tool and power control. Characterization showed mostly separate Al and Mg regions in the weld, usually with a hook protruding from Al into Mg, which likely contributed to high joint strength. Nanohardness mapping showed higher hardness in thin Mg swirls into the Al nugget, likely due to the intermetallics. The study used the industry standard SAE J2334 Cyclic Corrosion Test (CCT) to simulate corrosion conditions over the life of a vehicle, as well as linear polarization testing and ASTM G71 pitting corrosion testing. Corrosion reactions were: H 2 O + ½O 2 + 2e - → 2OH - at the Al cathode, and either Mg → Mg 2+ + 2e - or Mg + 2OH - → Mg(OH) 2 + 2e - at the Mg anode, with electron transfer through the joint. Mass loss increased with Al section length, supporting the hypothesis that galvanic corrosion in Al-Mg joints is limited by the cathodic reaction. Both pitting corrosion (first anode reaction) and hydroxide film formation (second reaction) were observed. The J2334 CCT test method was slightly modified, adding a chromium solution cleaning step after each week of corrosion testing, in order to remove Mg oxides and hydroxides and accurately measure mass loss over time. That said, FSW joints treated in this way did not did not exhibit significant reduction in lap shear strength of the joints vs. newly welded samples which had not undergone corrosion. Corrosion appeared to consist mainly of pitting in Mg in a way which did not directly affect the bond between the materials where the joints failed. A Cahn-Hilliard phase field model coupled with electrical potential described the electronically mediated galvanic corrosion electrochemical reactions described above in the four-component Al-Mg-H 2 O-(H 2 O+½O 2 ) system. This 2-D model successfully predicted Mg(OH)₂ formation at the anode in some circumstances, and Mg pitting corrosion in others, and showed the correct electric field directions in both cases. The model predicted Mg pit corrosion depth within a factor of two of measured pits.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Scalable Nano-Scaffold SOFC Anode Architecture Enabling Direct Hydrocarbon Utilization

This project is based on WVU’s pending patents, technology and aims to design and modify the internal surfaces of the Ni/YSZ anode from currently commercially viable Solid Oxide Fuel Cells (SOFCs) using the additive manufacturing process of Atomic Layer Deposition (ALD). The surface architecture/scaffold added onto the internal surface of the anode possesses an engineered nanostructure but it features only commonly-used oxide conductors and electro-catalyst materials. The surface layer possesses a minimum thickness of ~2-40 nm and is solely designed to control the surface reforming reactions and to increase catalytic activity. Three-dimensional (3D) nano scaffold architectures with the noble metal nano-catalyst, low-cost bimetallic catalytic alloys, and nano-scale ionic conducting oxide fully compatible with the state-of-the-art Ni/YSZ anode, were applied to the internal surface of the entire porous SOFC anode using ALD. In the present work, the surface scaffold architecture is essentially multi-functional at the nano-scale, facilitated by the multiple heterostructured interfaces. It will significantly enhance the power density and cell durability for direct hydrocarbon utilization by (1) increasing the number of electrochemical reaction sites to enhance the hydrogen/hydrocarbon oxidation reactions; (2) reducing carbon formation; (3) mitigating the coarsening of backbone Ni phase and the oxidation attack of Ni from oxidants (e.g., H2O, CO2); and (4) promoting the internal reforming capabilities, especially for natural gas applications. ALD is employed to generate stable anode surface architectures that are uniform, precisely controllable at the atomic scale, and accurately repeatable for processing. The engineered anode surface nano-scaffold architecture was cataloged and analyzed using High-resolution Transmission Electron Microscopy (TEM), and cell power/durability performance assessed via comprehensive electrochemical performance testing with commercial specimens and relevant environments using hydrocarbon fuels. To the best of our knowledge, this project is the First Report on ALD of Ni/YSZ. The actual achievement of this Project includes (1). Successful demonstration of 7 types of ALD layers on Ni/YSZ anode, including Co, Ni, Mn, Pt, Ru, ZrOx and multi-functional nano-composite. (1). Conformal coating and subsequently spontaneously pinning the discrete nano-catalyst, including the precious metal nano-catalyst and the Ni and Co catalysts, on the YSZ surface upon the electrochemical operation in the reduced atmosphere. Those nano-catalysts on the ionic-conducting YSZ provided excellent sites for promoting internal reforming; (2). Demonstrated ALD coating increased both catalytic activity and conductivity of Ni/YSZ. Conformal coating provided dopants and introduced additional electrical conducting pathways on the YSZ ionic conductor. The doped surface layer of YSZ with mixed conductivity thus further introduces the active triple phase boundaries adjacent to the ALD-coated nano-catalysts such as Pt, Co, and Ni that are pinned on the YSZ surface. The nano-composite ALD coating on Ni/YSZ anode has significantly increased cell durability; and (3). ALD coating of Ni/YSZ anode increased the power density of the entire cell by 300%. For a long time, the SOFC performance, such as the power density, was deemed hindered by the cathode. The sluggish oxygen reduction reaction (ORR) in the cathode was deemed as hindering the power density of the SOFCs. For the anode-supported commercial SOFCs, the cell performance is considered to be limited by the cathode's performance. For the first time in the field of SOFC, this project has demonstrated that (1). the performance of commercial SOFCs can be further increased by the ALD coating on Ni/YSZ anode backbone. (2). ALD coating on Ni/YSZ fuel electrodes results in the enhancement of power density, and increased reliability, robustness, and endurance of SOFCs, for their application using both hydrogen and hydrocarbon fuels over the entire operating temperature range of 650-800ºC for the inherently functional commercial cells. (3). ALD coating provides alternative approaches of exsolutions for introducing the stable catalyst onto the internal surface of the Ni/YSZ electrode. ALD coating could be much more versatile than exsolution in employing the catalysts with various chemistries onto the various backbones. (4). Due to the negligible amount of ALD materials coated onto the internal surface of the porous cathode of the as-fabricated cells, a peak power density increase up to 300 % induced by ALD coating was simultaneously achieved in terms of both power density and specific power. (5). The ALD coating developed through this project was applied to both the SOFC and Solid Oxide Electrolysis Cells (SOEC). SOEC’s face a similar but more demanding need to improve the fuel electrode's performance. It opens further research directions for electrocatalytic surface nanoionics with a wide range of chemistry. It will revolutionize our ability to render the formation of a nanostructured electrode that has been constantly pursued yet barely achieved for practical SOFC/SOEC applications. The research is also immediately transformative since both the preliminary data and the proposed work are on the direct implantation of nanoionics into the state-of-the-art inherently functional SOCs. It represents an immediate impact on the commercial sectors in SOC technology since the applied ALD processing is computer-controlled ALD coating using the commercial ALD systems, and it is scalable to both the single cells and SOC stacks.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Roundtable on Foundational Science for Carbon-Neutral Hydrogen Technologies (Technology Status Document)

This document summarizes the status of carbon-neutral hydrogen production, storage and transport, and utilization. The state of the art in the implementation, limitations, and challenges of these technologies are summarized. Sources of hydrogen are broadly categorized as hydrcoarbons or water and the processes used to convert these sources to hydrogen as catalytic, thermochemical, or electrochemical. Catalytic steam methane reforming of methane is the dominant process today. Other processes have smaller production volumes and the technology is less mature, but are being deployed at increasing rates, most notably water electrolyzers for hydrogen fueling stations. Efficient transport and storage of hydrogen is one of the major challenges facing a hydrogen-based energy economy. This arises in part from its low volumetric energy density necessitating very high pressures or cryogenic temperatures to store sufficient amounts for practical applications. High-pressure compressed hydrogen cylinders are the incumbent hydrogen storage technology for applications such as light-duty fuel cell electric vehicles, for example. The storage of hydrogen in materials or in chemicals is being pursued to address the issues associated with compression, such as parasitic energy loss and weight, size, and cost of storage containers. The complex nature of the chemical and physical processes involved in the uptake, storage, and release of hydrogen has slowed the discovery of suitable hydrogen storage materials. Both small and large-scale storage face the challenge of embrittlement of the storage media by hydrogen. There is a myriad of uses of hydrogen offering the promises of improving the efficiency of various applications and reducing or eliminating CO 2 emissions. These range from direct electrochemical conversion to electricity to power vehicles and grid-level stationary applications to combustion to production of chemicals and commodities. One of the most impactful applications in terms of reduction of CO 2 emissions is fuel cell passenger vehicles and heavy-duty vehicles such as class 8 trucks. The challenges facing widespread deployment of fuel cells, beyond the major hurdle of the lack of a hydrogen distribution infrastructure, are cost and durability, primarily related to the precious metal cathode catalyst and its durability. The other uses of hydrogen from conversion to hydrocarbons, polymer upcycling, and upgrading of bio-oils are at varying stages of maturity and also face fundamental challenges associated with catalytic processes and materials.

08 HYDROGEN↗
DOE OSTI2019

Extreme Fast Charge Challenges for Lithium-Ion Battery: Variability and Positive Electrode Issues

Enabling a 10 min fast charge for electric vehicles is a possible route to reduce range anxiety and increase the utility of electric vehicles. While lithium plating during fast charging is a known challenge, the full suite of limitations which occur in full cells during a 10 min fast charge are unknown. In the present work the central constraints of extreme fast charging are explored through extensive experiments and analysis in single layer graphite/NMC532 pouch cells. Methods of developing fast-charging protocols considering the impedance and transport limitations are presented and the relative benefits of altering the charging rate, profile, relaxation, etc., are investigated. Analysis during and at the end of cycling identified both known and unexpected aging pathways. The most distinct outcomes from the work are a significant increase in cell-to-cell variability as the number of fast charge cycles increase [up to 11% (1σ)] and the identification of distinct aging of the NMC532 positive electrode including cracking of the secondary particles and a trend toward under-lithiation of the positive electrode. Here, while significant aging of the positive electrode was observed, only a few conditions had discernible Li plating and no distinct reversible Li signature was seen during periodic reference performance tests.

25 ENERGY STORAGE↗
DOE OSTI2025

Anion exchange membranes based on (3-acrylamidopropyl) trimethylammonium chloride (APTA) and phenyl Acrylate: Impact of crosslinker and crosslinker content on physiochemical properties and transport behavior of acetate and formate

CO 2 reduction cells are innovative devices that convert CO 2 into valuable chemicals, such as formate (OFm - ) and acetate (OAc - ), at the cathode. One of the key challenges in these devices is the development of ion exchange membranes that enable the transport of charge carriers between electrodes while minimizing the transfer of CO 2 reduction products. This study focuses on the preparation and characterization of crosslinked anion exchange membranes (AEMs) made of phenyl acrylate (PA) and (3-acrylamidopropyl) trimethylammonium chloride (APTA), crosslinked with either poly(ethylene glycol) diacrylate (PEGDA) or N,N’-methylenebisacrylamide (MBAA). Here, the membranes are characterized to understand their physiochemical properties and corresponding transport behavior through characterization of water volume fraction, mechanical properties, ionic conductivity, ion exchange capacity, water contact angle, glass transition temperature as well as their permeability and solubility to formate and acetate. MBAA crosslinked membranes exhibit higher Young’s modulus and lower strain at break compared to PEGDA-crosslinked membranes, which is attributed to their shorter chain length. Within a series of membranes of varied comonomer content, for either PEGDA or MBAA as crosslinker, permeabilities generally follow free volume theory (increasing permeability with increasing water content where water content increases with decreasing crosslinker content). Interestingly, for membranes with different crosslinkers but analogous water volume fraction significant differences (∼2 orders of magnitude) in permeability are observed which we attribute to differences in chain mobility as characterized through the glass transition temperature.

25 ENERGY STORAGE↗
DOE OSTI2019

Enhanced Light Extraction from Low Cost White OLEDs Fabricated on Novel Patterned Substrates” (Final Report)

Organic LEDs (OLEDs) are a very attractive emerging solid state lighting (SSL) technology. Currently, one of the main challenges is to increase the extraction of the light generated inside the OLED into the forward (viewing) hemisphere. In conventional OLEDs fabricated on a transparent flat anode coated on glass the outcoupling factor is only about 20%. About 50% of the light is lost at the metal cathode (surface plasmon excitation), and waveguided internally in the organic layers and the transparent anode. Another ~30% is waveguided in the substrate to its edges. The research addressed this issue of outcoupling by evaluating OLEDs fabricated on corrugated plastic substrates manufactured in a cost-effective approach. It demonstrated that the outcoupling from such OLEDs can exceed 50% by mitigating plasmon–related loss and internal waveguiding, even without the addition of a microlens array or a hemispherical lens, either of which extracts the light trapped in the substrate. Simulations conducted in parallel with the experimental effort demonstrated how the corrugation assists in the outcoupling. The project also evaluated the role of the corrugation pitch and height in determining the outcoupling factor and other properties of the OLEDs. The technical effectiveness and economic feasibility of the project lie in the patterning of the extracting plastic substrates in an approach that is scalable to roll-to-roll (R2R) manufacturing. R2R processes are drastically lower-cost than batch or single-unit fabrication. The corrugated plastic substrates studied are part of an integrated substrate that includes also a microlens array at the air-side of the substrate and a conductive electrode. The project that was a university-industry collaboration is of major benefit to the public as it demonstrates the feasibility of manufacturing highly efficient OLEDs for SSL in a R2R process, which would drastically reduce the manufacturing cost and increase production in the USA. SSL is efficient and environmentally-friendly. It reduces electricity consumption, and hence lighting cost.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2017

OLED Lighting Substrate and Encapsulation System for Breakthrough Cost Reductions

OLED lighting is predicted to contribute a significant part of the US energy savings that will result from the implementation of Solid-State Lighting (SSL). OLED lighting adoption is predicted to reach approximately 5% of the lighting market by 2020. The primary purpose of this study was to address a barrier in OLED lighting adoption, this being OLED production costs. This project enabled the elimination of the anode patterning steps, by physically insulating the cathode contact area from the blanket coated ITO anode. Furthermore, this technology eliminates the need to change shadow masks between the organic materials and the cathode, making the OLED deposition machines simpler, lower cost, and less prone to particle generation. Finally, the process developed here permits the creation of a perfectly hermetic seal thereby eliminating the cost of desiccant materials. In this project, we successfully developed an ultrasonic soldering process to create a perfectly hermetic metal-on-glass bond. This required the evaluation of many ultrasonic solder materials, soldering parameters, and solder hardware configurations. In addition, methods to evaluate the hermeticity of the solder seal were developed and successfully tested. Our work demonstrated the ability to make a hermetic solder seal between a device glass and a cover glass using a Cerasolzer 155 ultrasonic solder. The resulting process could be leveraged to almost any OLED configuration. As we did not have the opportunity to produce a significant quantity of OLED devices for environmental testing, hermeticity was verified by measuring helium leakage rates through the seal. A second facet of this project required the development of a patterned glass frit insulating barrier over surface of the anode. To accomplish this, the appropriate insulator formulation and geometry needed to be established. In addition, this insulator needed to be robust enough to hold up to the ultrasonic soldering process previously mentioned. Given the aggressive nature of the ultrasonic soldering process, it was a significant challenge to develop an insulator which would withstand the resulting solder cavitation. The frit material and firing process turned out to be quite expensive and time consuming which was a major contributor to the higher than anticipated cost of this technology. In the end, it was found that a Vanadium Phosphate glass frit provided the most reliable insulator over the ITO.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Challenges for and Pathways Toward Solid-State Batteries

Solid-state batteries utilizing lithium metal anodes have the potential to enable batteries with a specific energy of >500 Wh/kg and an energy density of >1,500 Wh/L for thousands of cycles. When optimized they will improve the energy efficiency, operating temperature range, sustainability, and safety at a lower cost compared to projections for advanced Li-ion batteries. This improved performance is critical for the widespread adoption of electric vehicles and may enable future applications such as electric aviation. Expectations for solid-state batteries are high, there are significant materials and processing challenges that need to be overcome. Some of these challenges are well known; others are more subtle and are just becoming known. The challenges and their solutions must be clearly identified to realize high-energy solid-state Li metal batteries. In the United States, the U.S. Department of Energy (DOE) funds the majority of energy storage research and development, including solid state battery research. Web of Science publication analysis shows that worldwide DOE is second largest funder. Work on solid state batteries is distributed across different arms of DOE and is coordinated at headquarters to ensure a broad national portfolio for advanced batteries, including lithium batteries and solid-state battery devices. We note that university and national laboratory researchers in the US with a long-standing interest in solid state batteries is a small, integrated community with recognized impact for publications, patents and startup companies. The opportunity for this group to engage for research with international colleagues is growing, fostered by periodic bilateral meetings supported by DOE and by the recent joint US German research program for lithium battery interface studies. These are valuable opportunities to speed solid-state battery development. The ORNL led virtual workshop, overviewed here, confirms the community’s shared vision of the exciting advances, opportunities, and challenges. Further, we are seeing that this workshop has spawned several new informal collaborations and draft proposals. This encourages us to propose future discussion. On May 11, 2020, Oak Ridge National Laboratory (ORNL) hosted a 6-hour, on-line national workshop to discuss recent advances and most the prominent obstacles to realizing solid-state Li metal batteries. The workshop included more than 30+ experts from national laboratories, universities, and companies, all of whom have worked on solid-state batteries for multiple years. The participants shared recent advances, many not yet in print, illustrating that the community has gained significant new insights for solid-state Li battery materials over the last 5 years. In this report, the major outcomes of the workshop are organized to identify the gaps in our scientific knowledge for four core materials science areas: (1) Li metal anodes, (2) the solid electrolyte in contact with Li metal, (3) active cathode materials and solid-state composite cathodes, and (4) solid electrolytes. Illustrative examples and discussions are reported with the more comprehensive issues in the report. Discussion of additional challenges related to processing of solid-state battery materials and to the designs and architectures for mechanically robust, long-lived batteries received less attention due to time constraints. These are good themes for deeper discussion at a follow-on workshop, where a complete list of critical research topics can be identified.

25 ENERGY STORAGE↗
DOE OSTI2025

Gas-solid reaction-based selective lithium leaching strategy for efficient LiFePO 4 recycling

As the electric-vehicle market continues to expand, LiFePO 4 (LFP) batteries, valued for their intrinsic safety and cost-effectiveness, are being increasingly utilized. However, this widespread adoption highlights the urgent need for innovative and environmentally friendly recycling methods for spent LFP batteries due to their relatively low material value and the environmental challenges associated with traditional recycling processes. Here, in this study, we present a novel selective lithium leaching technique that involves a gas–solid reaction with chlorine gas. This method achieves a remarkable leaching efficiency of 99.8 % and a selectivity of 98.8 % at 200 °C within just 10 min, without generating acidic wastewater. The resulting LiCl solution was successfully converted into Li 2 CO 3 with an excellent purity of 99.5 %, while producing NaCl solution as the only byproduct. Notably, the olivine structure of the LFP was preserved as FePO 4 after lithium leaching. The regenerated LFP demonstrated excellent performance, retaining 94.1 % of its capacity after 150 cycles, while the lithium-leached FePO 4 delivered a reversible capacity exceeding 150 mAh/g. This approach not only enhances the efficiency of LFP recycling but also paves the way for more sustainable battery technologies.

36 MATERIALS SCIENCE↗