Search NASA⌕ Search

SEARCH · Search NASA

Results for “computers orbits”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

CFD-Predicted Tile Heating Bump Factors Due to Tile Overlay Repairs

A Computational Fluid Dynamics investigation of the Orbiter's Tile Overlay Repair (TOR) is performed to assess the aeroheating Damage Assessment Team's (DAT) existing heating correlation method for protuberance interference heating on the surrounding thermal protection system. Aerothermodynamic heating analyses are performed for TORs at the design reference damage locations body points 1800 and 1075 for a Mach 17.9 and a=39deg STS-107 flight trajectory point with laminar flow. Six different cases are considered. The computed peak heating bump factor on the surrounding tiles are below the DAT's heating bump factor values for smooth tile cases. However, for the uneven tiles cases the peak interference heating is shown to be considerably higher than the existing correlation prediction.

Lessard, Victor R.↗
NASA NTRS1995

Operation of the computer model for direct atomic oxygen exposure of Earth satellites

One of the primary causes of material degradation in low Earth orbit (LEO) is exposure to atomic oxygen. When atomic oxygen molecules collide with an orbiting spacecraft, the relative velocity is 7 to 8 km/sec and the collision energy is 4 to 5 eV per atom. Under these conditions, atomic oxygen may initiate a number of chemical and physical reactions with exposed materials. These reactions contribute to material degradation, surface erosion, and contamination. Interpretation of these effects on materials and the design of space hardware to withstand on-orbit conditions requires quantitative knowledge of the atomic oxygen exposure environment. Atomic oxygen flux is a function of orbit altitude, the orientation of the orbit plan to the Sun, solar and geomagnetic activity, and the angle between exposed surfaces and the spacecraft heading. We have developed a computer model to predict the atomic oxygen exposure of spacecraft in low Earth orbit. The application of this computer model is discussed.

Bourassa, R. J.↗
NASA NTRS1980

Level B/C software ground navigation program. Delta-T processor

The Delta-T Processor (DTP) computes the instantaneous downtrack error in a specified orbiter onboard navigation state vector recovered via downlink telemetry. The downtrack error, expressed in units of time, is computed based on current incoming Earth based range and Doppler navigation tracking data and the ground selected onboard navigation state vector. The computed time difference when used to modify the timetag of the vector used for onboard navigation reduces the instantaneous downtrack error in this vector to within the threshold of the DTP, the input data, and the onboard software. This threshold is currently estimated to be approximately 2 to 4 nautical miles. The DTP is not restricted to using only onboard vectors. Any vector, either input via the manual entry device or accessible via the vector administration table, may be used. The DTP does not require that both data types be available.

Source record↗
NASA NTRS1992

Would a Galactic bar destroy the globular cluster system?

Five different dynamical Galaxy models are presented for the Galactic potential which satisfy the observed rotation curve but contain a central bar so that the 3-kpc nonintersecting streamlines have a radial velocity of 50 km/s when viewed at 45 deg to the bar axis. The effect of the central bars on the destruction rates of globular clusters in the Galaxy is investigated. The method of Aguilar et al. (1988) is applied to these barred Galaxy models. The unknown tangential velocity components of each observed cluster are drawn randomly from an assumed distribution function. The cluster's orbit is integrated, and the bulge shocking rate is calculated. The median destruction rate of the cluster is computed by sampling a large number of such orbits. The addition of the rotating bar does not strongly affect the destruction rates of globular clusters. There is a small increase in the destruction rate for those clusters within about 2.5 kpc. Thus it is not possible to rule out the existence of a rotating bar on these grounds.

Long, Kevin↗
NASA NTRS1986

Three dimensional simulation of the operation of a hollow cathode electron emitter on the Shuttle orbiter

Several researchers have suggested using hollow cathodes as plasma contactors for electrodynamic tethers, particularly to prevent the shuttle orbiter from charging to large negative potentials. Previous studies have shown that fluid models with anomalous scattering can describe the electron transport in hollow cathode generated plasmas. An improved theory of the hollow cathode plasmas is developed and computational results using the theory are compared with laboratory experiment. Numerical predictions for a hollow cathode plasma source of the type considered for use on the shuttle are presented as are three-dimensional NASCAP/LEO calculations of the emitted ion trajectories and the resulting potentials in the vicinity of the orbiter. The computer calculations show that the hollow cathode plasma source makes vastly superior contact with the ionospheric plasma compared with either an electron gun or passive ion collection by the orbiter.

Davis, V. A.↗
NASA NTRS1987

Atmospheric reentry of the in-core thermionic SP-100 reactor system

Presumed end-of-life atmospheric reentry of the GA SP-100 system was studied to assess dispersal feasibility and associated hazards. Reentry was studied by sequential use of an orbital trajectory and a heat analysis computer program. Two heating models were used. The first model assumed a thermal equilibrium condition between the stagnation point aerodynamic heating and the radiative cooling of the skin material surface. The second model allowed for infinite conductivity of the skin material. Four reentering configurations were studied representing stages of increased SP-100 breakup: (1) radiator, shield and reactor, (2) shield and reactor, (3) reactor with control drums, and (4) reactor without control drums. Each reentering configuration was started from a circular orbit at 116 km having an inertial velocity near Mach 25. The assumed failing criterion was the attainment of melting temperature of a critical system component. The reentry analysis revealed breakup of the vessel in the neighborhood of 61 km altitude and scattering of the fuel elements. Subsequent breakup of the fuel elements was not predicted. Oxidation of the niobium skin material was calculated to cause an increase in surface temperature of less than ten percent. The concept of thermite analogs for enhancing reactor reentry dispersal was assessed and found to be feasible in principle. A conservative worst-case hazards analysis was performed for radioactive and nonradioactive toxic SP-100 materials assumed to be dispersed during end-of-life reentry. The hazards associated with this phase of the SP-100 mission were calculated to be insignificant.

Stamatelatos, M. G.↗
NASA NTRS1987

Effects of forced and free convections on structural temperatures of Space Shuttle Orbiter during reentry flight

Structural performance and resizing (SPAR) finite-element thermal analysis computer program was used in the heat transfer analysis of the Space Shuttle Orbiter wing subjected to reentry aerodynamic heating. With sufficient external forced convective cooling near the end of the heating cycle, the calculated surface temperatures of the thermal protection system (TPS) agree favorably with the flight data for the entire flight profile. However, the effects of this external forced convective cooling on the structural temperatures were found to be negligible. Both free convection and forced convection elements were introduced to model the internal convection effect of the cool air entering the Shuttle interior. The introduction of the internal free convection effect decreased the calculated wing lower skin temperatures by 20 F at most, 1200 sec after touchdown. If the internal convection is treated as forced convection, the calculated wing lower skin temperatures after touchdown can be reduced to match the flight-measured data very closely. By reducing the TPS thicknesses to certain effective thickness to account for the TPs gap heating, the calculated wing lower skin temperatures prior to touchdown can be raised to agree with the flight data perfectly.

Ko, William L.↗
NASA NTRS1986

Recovery of the UCAS asteroids

The astrometric measurements of the original 1981 UCAS survey plates were computed, leading to a grand total of 1252 orbits for newly discovered asteroids ranging in absolute magnitude from H = 10.5 to 19.5. New programs were created and existing computer routines were revised at Lowell Observatory, which has streamlined the process of correctly identifying asteroid images on archival photographic plates. The recovery and accurate measurements were made of 130 UCAS asteroids at other oppositions on plates taken by C. T. Kowal at Palomar Mountain in 1978 and 1979. When added to the 90 other UCAS objects identified by other investigators, this brings the total of multiple-opposition orbits to 220. Of the 56 UCAS asteroids known to be planet crossing, 11 were recovered at second oppositions. The recovery and accurate measurements of about 20 non-UCAS asteroids identified on the plates were examined.

Shoemaker, E. M.↗
NASA NTRS1991

Collar grids for intersecting geometric components within the Chimera overlapped grid scheme

A method for overcoming problems with using the Chimera overset grid scheme in the region of intersecting geometry components is presented. A 'collar grid' resolves the intersection region and provides communication between the component grids. This approach is validated by comparing computed and experimental data for a flow about a wing/body configuration. Application of the collar grid scheme to the Orbiter fuselage and vertical tail intersection in a computation of the full Space Shuttle launch vehicle demonstrates its usefulness for simulation of flow about complex aerospace vehicles.

Parks, Steven J.↗
NASA NTRS2011

The Stability of Powered Flight around Asteroids with Application to Vesta

The reliability of low-thrust trajectories between science orbits around large asteroids must be evaluated subject to the unavoidable uncertainties of orbit determination, asteroid physical parameters, momentum de-saturation maneuvers, and transfer maneuver execution error. This paper presents a computationally inexpensive way to extend the concept or orbital stability to trajectories undergoing continuously powered low-thrust flight. Trajectories that are stable using this measure are shown to be stable under the combined uncertainties expected during operations. The measure is general and relatively simple to implement. The method was applied to maneuvers planed around the asteroid Vesta in support of NASA's Dawn Discovery mission.

Dawn↗
NASA NTRS1981

Spacecraft computer resource margin management

The conduction of the Project Galileo Orbiter, with 18 microcomputers and the equivalent of 360K 8-bit bytes of memory contained within two major engineering subsystems and eight science instruments, requires that the key onboard computer system resources be managed in a very rigorous manner. Attention is given to the rationale behind the project policy, the development stage, the preliminary design stage, the design/implementation stage, and the optimization or 'scrubbing' stage. The implementation of the policy is discussed, taking into account the development of the Attitude and Articulation Control Subsystem (AACS) and the Command and Data Subsystem (CDS), the reporting of margin status, and the response to allocation oversubscription.

Larman, B. T.↗
NASA NTRS2008

Heating Augmentation for Short Hypersonic Protuberances

Computational aeroheating analyses of the Space Shuttle Orbiter plug repair models are validated against data collected in the Calspan University of Buffalo Research Center (CUBRC) 48 inch shock tunnel. The comparison shows that the average difference between computed heat transfer results and the data is about 9.5%. Using CFD and Wind Tunnel (WT) data, an empirical correlation for estimating heating augmentation on short hypersonic protuberances (k/delta less than 0.3) is proposed. This proposed correlation is compared with several computed flight simulation cases and good agreement is achieved. Accordingly, this correlation is proposed for further investigation on other short hypersonic protuberances for estimating heating augmentation.

Mazaheri, Ali R.↗
NASA NTRS2008

Heating Augmentation for Short Hypersonic Protuberances

Computational aeroheating analyses of the Space Shuttle Orbiter plug repair models are validated against data collected in the Calspan University of Buffalo Research Center (CUBRC) 48 inch shock tunnel. The comparison shows that the average difference between computed heat transfer results and the data is about 9:5%. Using CFD and Wind Tunnel (WT) data, an empirical correlation for estimating heating augmentation on short hyper- sonic protuberances (k/delta < 0.33) is proposed. This proposed correlation is compared with several computed flight simulation cases and good agreement is achieved. Accordingly, this correlation is proposed for further investigation on other short hypersonic protuberances for estimating heating augmentation.

Mazaheri, Alireza R.↗
NASA NTRS2010

Hypersonic Navier-Stokes Comparisons to Orbiter Flight Data

During the STS-119 flight of Space Shuttle Discovery, two sets of surface temperature measurements were made. Under the HYTHIRM program3 quantitative thermal images of the windward side of the Orbiter with a were taken. In addition, the Boundary Layer Transition Flight Experiment 4 made thermocouple measurements at discrete locations on the Orbiter wind side. Most of these measurements were made downstream of a surface protuberance designed to trip the boundary layer to turbulent flow. In this paper, we use the US3D computational fluid dynamics code to simulate the Orbiter flow field at conditions corresponding to the STS-119 re-entry. We employ a standard two-temperature, five-species finite-rate model for high-temperature air, and the surface catalysis model of Stewart.1 This work is similar to the analysis of Wood et al . 2 except that we use a different approach for modeling turbulent flow. We use the one-equation Spalart-Allmaras turbulence model8 with compressibility corrections 9 and an approach for tripping the boundary layer at discrete locations. In general, the comparison between the simulations and flight data is remarkably good

Candler, Graham V.↗
NASA NTRS1978

Static and dynamic stability analysis of the space shuttle vehicle-orbiter

The longitudinal static and dynamic stability of a Space Shuttle Vehicle-Orbiter (SSV Orbiter) model is analyzed using the FLEXSTAB computer program. Nonlinear effects are accounted for by application of a correction technique in the FLEXSTAB system; the technique incorporates experimental force and pressure data into the linear aerodynamic theory. A flexible Orbiter model is treated in the static stability analysis for the flight conditions of Mach number 0.9 for rectilinear flight (1 g) and for a pull-up maneuver (2.5 g) at an altitude of 15.24 km. Static stability parameters and structural deformations of the Orbiter are calculated at trim conditions for the dynamic stability analysis, and the characteristics of damping in pitch are investigated for a Mach number range of 0.3 to 1.2. The calculated results for both the static and dynamic stabilities are compared with the available experimental data.

Chyu, W. J.↗
NASA NTRS2010

Using MathCad to Evaluate Exact Integral Formulations of Spacecraft Orbital Heats for Primitive Surfaces at Any Orientation

With the advent of high speed computing Monte Carlo ray tracing techniques has become the preferred method for evaluating spacecraft orbital heats. Monte Carlo has its greatest advantage where there are many interacting surfaces. However Monte Carlo programs are specialized programs that suffer from some inaccuracy, long calculation times and high purchase cost. A general orbital heating integral is presented here that is accurate, fast and runs on MathCad, a generally available engineering mathematics program. The integral is easy to read, understand and alter. The integral can be applied to unshaded primitive surfaces at any orientation. The method is limited to direct heating calculations. This integral formulation can be used for quick orbit evaluations and spot checking Monte Carlo results.

Pinckney, John↗
NASA NTRS1987

Thermal stress analysis of space shuttle orbiter subjected to reentry aerodynamic heating

A structural performance and resizing (SPAR) finite-element computer program and NASA structural analysis (NASTRAN) finite-element computer programs were used in the thermal stress analysis of the space shuttle orbiter subjected to reentry aerodynamic heating. A SPAR structural model was set up for the entire left wing of the orbiter, and NASTRAN structural models were set up for: (1) a wing segment located at midspan of the orbiter left wing, and (2) a fuselage segment located at midfuselage. The thermal stress distributions in the orbiter structure were obtained and the critical high thermal stress regions were identified. It was found that the thermal stresses induced in the orbiter structure during reentry were relatively low. The thermal stress predictions from the whole wing model were considered to be more accurate than those from the wing segment model because the former accounts for temperature and stress effects throughout the entire wing.

Ko, William L.↗