Search NASA⌕ Search

SEARCH · Search NASA

Results for “doping effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Studies on structural and electrical properties of pure and doped h-YMnO{sub 3}

In the present communication, we report the results of the structural and electrical studies on pure YMnO{sub 3} (YMO) and Zr doped Y{sub 0.95}Zr{sub 0.05}MnO{sub 3} (YZMO) samples, synthesized using low cost sol-gel technique. To understand the structural properties, structural phases present and effect of doping on the structural behavior, X-ray diffraction (XRD) measurements were carried out for both the samples understudy. XRD results reveal the single phasic nature of both the samples having hexagonal unit cell structure. Improved crystal structure has been observed for pure YMnO{sub 3} sample while doping of Zr at Y-site degrades the structure of the sample. Improved dielectric constant and enhanced AC conductivity (σ{sub a}) have been discussed on the basis of charge carrier polarization and correlated barrier hopping due to the localized state.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Enhanced photovoltaic performance of nanocrystalline CdTe/ZnO solar cells using sol-gel ZnO and positive bias treatment

The effect of doping and porosity of the n-type ZnO layer on the performance of solution-processed, sintered p-CdTe/n-ZnO nanocrystal photovoltaic (PV) devices is investigated. Amorphous sol-gel ZnO is found to be the best candidate with overall energy conversion efficiencies above 8% obtained if the ZnO is also indium doped. We demonstrate that when such PV devices are left under forward bias (in dark or light), the device efficiency values are raised to at least 9.8%, due to a substantially increased open-circuit voltage and fill-factor. This drastic enhancement is attributed to improved band alignment at the ITO/CdTe interface. The forward-bias treatment is slowly reversed over a period of days to weeks on standing under open circuit conditions, but is readily restored with further voltage treatment. The moderate processing conditions and high efficiency of such devices demonstrate that nanocrystal-based systems are a promising technology for photovoltaics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Solution-Processed n-Type Graphene Doping for Cathode in Inverted Polymer Light-Emitting Diodes

n-Type doping with (4-(1,3-dimethyl-2,3-dihydro-1H-benzoimidazol-2-yl)phenyl) dimethylamine (N-DMBI) reduces a work function (WF) of graphene by ~0.45 eV without significant reduction of optical transmittance. Solution process of N-DMBI on graphene provides effective n-type doping effect and air-stability at the same time. Although neutral N-DMBI act as an electron receptor leaving the graphene p-doped, radical N-DMBI acts as an electron donator leaving the graphene n-doped, which is demonstrated by density functional theory. We also verify the suitability of N-DMBI-doped n-type graphene for use as a cathode in inverted polymer light-emitting diodes (PLEDs) by using various analytical methods. Inverted PLEDs using a graphene cathode doped with N-DMBI radical showed dramatically improved device efficiency (~13.8 cd/A) than did inverted PLEDs with pristine graphene (~2.74 cd/A). Finally, N-DMBI-doped graphene can provide a practical way to produce graphene cathodes with low WF in various organic optoelectronics.

36 MATERIALS SCIENCE↗

Microstructural evolution in NaNbO{sub 3}-based antiferroelectrics

Our recent study found that CaZrO{sub 3} doping can effectively enhance the antiferroelectric P phase in NaNbO{sub 3} ceramics, leading to a double polarization hysteresis loop characteristic of a reversible antiferroelectric ↔ ferroelectric phase transition [Shimizu et al., Dalton Trans. 44, 10763 (2015)]. Here, a thorough transmission electron microscope study was performed to illustrate the CaZrO{sub 3} doping-assisted antiferroelectricity stabilization. In parallel to the bright-field imaging and selected area electron diffraction from multiple zone axes, detailed dark-field imaging was utilized to determine the superlattice structural origins, from either oxygen octahedral tilting or antiparallel cation displacements. By analogy with Pb(Zr{sub 1−x}Ti{sub x})O{sub 3} and rare-earth doped BiFeO{sub 3} systems, the chemical substitutions are such as to an induced polar-to-antipolar transition that is consistent with a tolerance factor reduction. The resultant chemical pressure has a similar effect to the compressive hydrostatic pressure where the antiferroelectric state is favored over the ferroelectric state.

36 MATERIALS SCIENCE↗

The effect of substrate temperature and growth rate on the doping efficiency of single crystal boron doped diamond

The substrate growth temperature dependence of the plasma gas-phase to solid-phase doping efficiency in single crystal, boron doped diamond (BDD) deposition is investigated. Single crystal diamond (SCD) is grown by microwave plasma assisted chemical vapor deposition (MPACVD) on high pressure, high temperature (HPHT) type Ib substrates. Samples are grown at substrate temperatures of 850-950 degrees C for each of five doping concentration levels, to determine the effect of the growth temperature on the doping efficiency and defect morphology. The substrate temperature during growth is shown to have a significant effect on the grown sample defect morphology, and a temperature dependence of the doping efficiency is also shown. The effect of the growth rate on the doping efficiency is discussed, and the ratio of the boron concentration in the gas phase to the flux of carbon incorporated into the solid diamond phase is shown to be a more predictive measure of the resulting boron concentration than the gas phase boron to carbon ratio that is more commonly reported. (C) 2014 Elsevier B.V. All rights reserved.

Demlow, SN↗

Heteroatom-Doped Flash Graphene

Heteroatom doping can effectively tailor the local structures and electronic states of intrinsic two-dimensional materials, and endow them with modified optical, electrical, and mechanical properties. Recent studies have shown the feasibility of preparing doped graphene from graphene oxide and its derivatives via some post-treatments, including solid-state and solvothermal methods, but they require reactive and harsh reagents. However, direct synthesis of various heteroatom-doped graphene in larger quantities and high purity through bottom-up methods remains challenging. Here, we report catalyst-free and solvent-free direct synthesis of graphene doped with various heteroatoms in bulk via flash Joule heating (FJH). Seven types of heteroatom-doped flash graphene (FG) are synthesized through millisecond flashing, including single-element-doped FG (boron, nitrogen, oxygen, phosphorus, sulfur), two-element-co-doped FG (boron and nitrogen), as well as three-element-co-doped FG (boron, nitrogen, and sulfur). Here, a variety of low-cost dopants, such as elements, oxides, and organic compounds are used. The graphene quality of heteroatom-doped FG is high, and similar to intrinsic FG, the material exhibits turbostraticity, increased interlayer spacing, and superior dispersibility. Electrochemical oxygen reduction reaction of different heteroatom-doped FG is tested, and sulfur-doped FG shows the best performance. Lithium metal battery tests demonstrate that nitrogen-doped FG exhibits a smaller nucleation overpotential compared to Cu or undoped FG. The electrical energy cost for the synthesis of heteroatom-doped FG synthesis is only 1.2 to 10.7 kJ g –1 , which could render the FJH method suitable for low-cost mass production of heteroatom-doped graphene.

01 COAL, LIGNITE, AND PEAT↗

High Electron Mobility SiGe/Si Transistor Structures on Sapphire Substrates

SiGe/Si n-type modulation doped field effect structures and transistors (n-MODFETs) have been fabricated on r-plane sapphire substrates. The structures were deposited using molecular beam epitaxy, and antimony dopants were incorporated via a delta doping process. Secondary ion mass spectroscopy (SIMS) indicates that the peak antimony, concentration was approximately 4 x 10(exp19) per cubic cm. The electron mobility was over 1,200 and 13,000 sq cm/V-sec at room temperature and 0.25 K, respectively. At these two temperatures, the electron carrier densities were 1.6 and 1.33 x 10(exp 12) per sq cm, thus demonstrating that carrier confinement was excellent. Shubnikov-de Haas oscillations were observed at 0.25 K, thus confirming the two-dimensional nature of the carriers. Transistors, with gate lengths varying from 1 micron to 5 microns, were fabricated using these structures and dc characterization was performed at room temperature. The saturated drain current region extended over a wide source-to-drain voltage (V(sub DS)) range, with (V(sub DS)) knee voltages of approximately 0.5 V and increased leakage starting at voltages slightly higher than 4 V.

Alterovitz, Samuel A.↗

High Electron Mobility SiGe/Si Transistor Structures on Sapphire Substrates

SiGe/Si n-type modulation doped field effect structures and transistors (n-MODFETs) have been fabricated on r-plane sapphire substrates. The structures were deposited using molecular beam epitaxy, and antimony dopants were incorporated via a delta doping process. Secondary ion mass spectroscopy (SIMS) indicates that the peak antimony concentration was approximately 4 x 10(exp 19) per cubic centimeter. At these two temperatures, the electron carrier densities were 1.6 and 1.33 x 10(exp 12) per square centimeter, thus demonstrating that carrier confinement was excellent. Shubnikov-de Haas oscillations were observed at 0.25 K, thus confirming the two-dimensional nature of the carriers. Transistors, with gate lengths varying from 1 micron to 5 microns, were fabricated using these structures and dc characterization was performed at room temperature. The saturated drain current region extended over a wide source-to-drain voltage (V (sub DS)) range, with V (sub DS) knee voltages of approximately 0.5 V and increased leakage starting at voltages slightly higher than 4 V.

Alterovitz, Samuel A.↗

Evidence for charge Kondo effect in superconducting Tl-doped PbTe

We report results of low-temperature thermodynamic and transport measurements of Pb{sub 1-x}Tl{sub x}Te single crystals for Tl concentrations up to the solubility limit of approximately x = 1.5%. For all doped samples, we observe a low-temperature resistivity upturn that scales in magnitude with the Tl concentration. The temperature and field dependence of this upturn are consistent with a charge Kondo effect involving degenerate Tl valence states differing by two electrons, with a characteristic Kondo temperature T{sub K} {approx} 6 K. The observation of such an effect supports an electronic pairing mechanism for superconductivity in this material and may account for the anomalously high T{sub c} values.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The influence of iron incorporation on the microstructure and crystal chemistry of UO 2 fuel

The incorporation of dopants into UO 2 is of interest for both doped advanced fuel and nuclear forensics research. Suitable forensics dopants, or taggants, for nuclear fuels are ones that do not adversely affect the performance of the parent material while still being traceable during key stages of the fuel’s life cycle. In this paper, we present our efforts to understand the effects of doping UO 2 with Fe 2 O 3 under multiple parameters, such as Fe concentration (0–3000 wppm), sintering temperature (1673 K, 1773 K, and 1973 K), sintering time (2–12 h), and atmosphere (reducing and inert). Here, we investigated densification behavior, microstructure evolution, and lattice defects based on the geometric densities, scanning electron microscopy (SEM), X-ray diffractograms, and Raman spectra. The effect of Fe on the microstructure and crystal chemistry of UO 2 is very complex, especially at the intermediate temperature (1773 K), where we found that densification kinetics are enhanced and that lattice contraction occurs for doping concentrations greater than 1000 wppm Fe.

Crystallography↗

Charge Transfer and Support Effects in Heterogeneous Catalysis

The kinetic, electronic and spectroscopic properties of two-dimensional oxide-supported catalysts were investigated in order to understand the role of charge transfer in catalysis. Pt/TiO 2 nanodiodes were fabricated and used as catalysts for hydrogen oxidation. During the reaction, the current through the diode, as well as its I-V curve, were monitored, while gas chromatography was used to measure the reaction rate. The current and the turnover rate were found to have the same temperature dependence, indicating that hydrogen oxidation leads to the non-adiabatic excitation of electrons in Pt. A fraction of these electrons have enough energy to ballistically transport through Pt and overcome the Schottky barrier at the interface with TiO 2 . The yield for this phenomenon is on the order of 10 -4 electrons per product molecule formed, similar to what has been observed for CO oxidation and for the adsorption of many different molecules. The same Pt/TiO 2 system was used to compare currents in hydrogen oxidation and deuterium oxidation. The current through the diode under deuterium oxidation was found to be greater than under hydrogen oxidation by a factor of three. Weighted by the difference in turnover frequencies for the two isotopes, this would imply a chemicurrent yield 5 times greater for D 2 compared to H 2 , contrary to what is expected given the higher mass of D 2 . Reversible changes in the rectification factor of the diode are observed when switching between D 2 and H 2 . These changes are a likely cause for the differences in current between the two isotopes. In the nanodiode experiments, surface chemistry leads to charge flow, suggesting the possibility of creating charge flow to tune surface chemistry. This was done first by exposing a Pt/Si diode to visible light while using it as a catalyst for H 2 oxidation. Absorption of the light in the Si, combined with the band bending at the interface, gives rise to a steady-state flow of hot holes to the surface. This leads to a decrease in turnover on the surface, an effect which is enhanced when a reverse bias is applied to the diode. Similar experiments were carried out for CO oxidation. On Pt/Si diodes, the reaction rate was found to increase when a forward bias was applied. When the diode was exposed to visible light and a reverse bias was applied, the rate was instead decreased. This implies that a flow of negative charges to the surface increases turnover, while positive charges decrease it. Charge flow in an oxide supported metal catalyst can be modified even without designing the catalyst as a solid state electronic device. This was done by doping stoichiometric and nonstoichiometric TiO 2 films with F, and using the resulting oxides as supports for Pt films. In the case of stoichiometric TiO 2 , F was found to act as an n-type dopant, creating a population of filled electronic states just below the conduction band, and dramatically increasing the conductivity of the oxide film. The electrons in those states can transfer to surface O, activating it for reaction with CO, and leading to increased turnover for CO oxidation. This reinforces the hypothesis that CO oxidation is activated by a flow of negative charges to the surface. The same set of catalysts was used for methanol oxidation. The electronic properties of the TiO 2 films again correlated with the turnover rates, but also with selectivity. With stoichiometric TiO 2 as the support, F-doping caused an increase in selectivity toward the formation of partial oxidation products, formaldehyde and methyl formate, versus the total oxidation product, CO 2 . With non-stoichiometric TiO 2 , F-doping had the reverse effect. Ambient Pressure X-Ray Photoelectron Spectroscopy was used to investigate this F-doping effect in reaction conditions. In O 2 alone, and in CO oxidation conditions, the O1s spectrum showed a high binding energy peak that correlated in intensity with the activity of the different films: for stoichiometric films, the peak decreased in intensity with F-doping, while for nonstoichiometric films, the opposite was observed. No such changes were visible in the C1s spectrum, confirming the role of O activation in the reaction. This thesis adds to the body of knowledge on the importance of charge transfer at the metal-oxide interface in shaping the reactivity of heterogeneous catalysts, and provides examples of how this can be the basis for new methods to tune reactivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Crossover between two-dimensional surface state and three-dimensional bulk phase in Fe-doped Bi{sub 2}Te{sub 3}

In Fe-doped Bi{sub 2}Te{sub 3}, we have observed higher mobility, larger linear magnetoresistance, and anomalous quantum oscillations. The angle dependence of Shubnikov-de Haas (SdH) oscillations gives two different periodicities depending on the angle from the c-axis. The low-angle SdH period is identified with a surface origin, while the high-angle period is against the surface origin. The high-angle SdH period well agrees with the de Haas-van Alphen (dHvA) period with a bulk origin. The physical parameters obtained from the quantum oscillations support the crossover between two-dimensional surface state and three-dimensional bulk phase by Fe doping in Bi{sub 2}Te{sub 3}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Topological Hall Effect in Antiferromagnetic Co-Doped Fe 3 GaTe 2

Fe 3 GaTe 2 is van der Waals (vdW) ferromagnet with a Curie temperature T C ranging from 350 K to 380 K, followed upon cooling by a ferrimagnetic transition near room temperature. Substituting Fe with Co was previously reported to induce antiferromagnetism (AFM) at a Co fraction dependent Néel temperature TN. In this work, we confirm the overall phase diagram of the Fe 3-x Co x GaTe 2 series as a function of x and temperature via magnetization and electrical transport measurements. For x ≥ 0.6 the Hall effect is observed to mimic the magnetization as the AF ground state is suppressed by the external magnetic field via a metamagnetic transition, thus displaying an anomalous Hall response. At low temperatures, we also observe a pronounced topological Hall signal peaking at μ 0 H = 4 T, or within the metamagnetic transition region of fields. This observation points to the presence of magnetic field-induced chiral spin textures, such as skyrmions upon approaching magnetization saturation. Remarkably, magnetic force microscopy (MFM) reveals the emergence of nearly circular magnetic domains, with diameters on the order of 100–200 nm, within the antiferromagnetic phase. Here, a detailed analysis of the MFM images indicates that the topological Hall effect is closely linked to the field-induced stabilization of magnetic domain structures, likely exhibiting chiral textures. This observation suggests the possible formation of skyrmions already in the AFM phase, i.e., AFM skyrmions, that evolve into ferromagnetic (FM) ones upon increasing the magnetic field. Consequently, Co-doped Fe 3 GaTe 2 might provide a platform to investigate the transformation of skyrmions, initially coupled antiferromagnetically into ferromagnetic skyrmions, and to explore its impact on the topological and skyrmion Hall effects.

anomalous Hall effect↗

Weak ferromagnetic ordering in Ca doped polycrystalline BiFeO{sub 3}

Structural and magnetic properties of polycrystalline BiFeO{sub 3}, Bi{sub 0.9}Ca{sub 0.1}FeO{sub 2.95}, Bi{sub 0.9}Ba{sub 0.05}Ca{sub 0.05}FeO{sub 2.95}, and Bi{sub 0.9}Ba{sub 0.1}FeO{sub 2.95} ceramic samples were studied to establish the effects of doping in BiFeO{sub 3} on the magnetic property. X-ray diffraction data of the undoped and doped BiFeO{sub 3} samples were refined to a rhombohedral structure with space group R3c. X-ray photoelectron spectroscopy study showed the formation of a single-phase in both the undoped and doped BiFeO{sub 3} ceramics with Fe in the 3+ valence state. Ca doped and Ba-Ca co-doped BiFeO{sub 3} ceramic samples show weak ferromagnetic ordering at room temperature. This observation makes Ca doped and Ba-Ca co-doped BiFeO{sub 3} samples an interesting material system for magnetoelectric coupling studies.

36 MATERIALS SCIENCE↗

Hole doping and electronic correlations in Cr substituted BaFe$_{2}$As$_{2}$

For a significant composition range, the suppression of the spin density wave transition temperature (T SDW ) in Cr- and Mn-substituted BaFe 2 As 2 (CrBFA and MnBFA, respectively) coincides as a function of Cr/Mn content, despite the distinct electronic effects of these substitutions. Additionally, for any Cr/Mn content superconductivity (SC) is absent and this topic is particularly less explored in the case of CrBFA. Here, in this work, we employ angle-resolved photoemission spectroscopy (ARPES) and combined density functional theory plus dynamical mean field theory (DFT+DMFT) to address the evolution of the Fermi surface (FS) and electronic correlations in CrBFA. Our findings reveal that incorporating Cr leads to an effective hole doping of the states near the FS, which is well described within the virtual crystal approximation (VCA). Moreover, analysis of the ARPES spectra of the bands with main d yz -orbital character reveals a fractional scaling of the imaginary part of self-energy as a function of the binding energy, a signature property of Hund's correlations. Our DFT+DMFT calculations support these experimental findings. We conclude that CrBFA is a correlated electron system for which the changes in the FS as a function of Cr are unrelated to the suppression of T SDW . In addition, we suggest that the absence of SC is primarily due to the competition between Cr local moments and the Fe-derived itinerant spin fluctuations.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Experimental Measurements of Soot and Soot Precursors of Sustainable Aviation Fuels

Sustainable Aviation Fuels (SAFs) are promising for decarbonizing the challenging-to-electrify aerospace sector and reducing yearly greenhouse gas emissions by thousands of tons. Developing predictive detailed chemical kinetic models for SAF (and traditional) fuel mixtures necessitates a robust experimental database to elucidate the intricate pyrolysis and oxidation chemistry of SAF fuel blend components. Two critical components of SAF surrogate mixtures are iso-dodecane isomers and trans-decalin. This report characterizes the structure of three slightly sooting, laminar, non-premixed, nitrogen-diluted Planar Mixing Layer Flames (PMLFs) fueled by either pure ethylene, ethylene doped with 1500ppm of either 2,2,4,6,6-pentamethyl-heptane or trans-decalin. The flames have the same stoichiometric mixture fraction and total mole fraction of fuels in the fuel stream (X F,F = X C2H4,F + X Dopant,F = 0.26), resulting in approximately the same maximum temperature (T max ≈ 1800 K) to highlight the effect of doping on soot and its gaseous precursors. The PMLF is unconfined and established between adjacent planar jets of the fuel and oxidizer streams surrounded by annular shielding nitrogen. The flow is stabilized by exhausting the hot buoyant flame products through a slot in a downstream plate onto which the cold flow impinges. Importantly, any horizontal cross-section of the PMLF has a self-similar thermochemical structure of a reactive boundary layer that grows at increasing Height Above the Burner (HAB). Therefore, the horizontal cross-sections of a PMLF can be modeled as a One-Dimensional Counterflow Flame (1D-CF) with very low strain rates which are unachievable in traditional CFs and yield a structure that is several millimeters thick. In brief, the PMLF is ideal for performing spatially resolved measurements with minimal effects of the sampling-induced perturbations, to develop and validate detailed chemical kinetic models on time scales of a few tens of milliseconds that are relevant in aviation applications. The horizontal profiles of C0-C18 gaseous species at HAB = 50 mm and soot volume fraction at 25 and 50 mm are measured using capillary sampling followed by GC-MS analyses and Laser Induced Emission Spectroscopy (LIES), respectively. Additionally, the Elastic Laser Light Scattering (E-LLS) coefficient is measured at HAB = 50 mm and 25 mm to determine the strain rates of the 1D-CFs equivalent to the characterized PMLF horizontal cross sections and the profile of the E-LLS equivalent diameter of soot. The comparison of the results in the base PMLF fueled only by ethylene with those in either doped PMLF in which 1500 ppm of ethylene are replaced with 2,2,4,6,6-pentamethyl-heptane or trans-decalin, reveals that the doping increases the mole fraction of several Polycyclic Aromatic Hydrocarbons (PAHs) at both HABs by a factor of approximately 2.5, and the soot volume fraction at both HABs by factors of ~1.5 for 2,2,4,6,6-pentamethyl-heptane and ~1.25 for trans-decalin doping, respectively. Conversely, doping causes a near doubling of the soot equivalent diameter only at HAB = 50 mm, without significant effects at 25 mm. The experimental results partially validate the tested state-of-the-art detailed chemical kinetic model and also point toward the further improvement of its predictive capabilities.

10 SYNTHETIC FUELS↗

Dielectric and electrical studies of Pr{sup 3+} doped nano CaSiO{sub 3} perovskite ceramics

Highlights: • CaSiO{sub 3}:Pr{sup 3+} was prepared by facile low temperature solution combustion method. • The crystalline phase of the product is obtained by adopting sintering method. • Samples prepared at 500 °C and calcined at 900 °C for 3 h showed β-phase. • The Pr{sup 3+} doped CaSiO{sub 3} shows “unusual results”. • The electrical microstructure has been accepted to be of internal barrier layer capacitor. - Abstract: CaSiO{sub 3} nano-ceramic powder doped with Pr{sup 3+} has been prepared by solution combustion method. The powder Ca{sub 0.95}Pr{sub 0.05}SiO{sub 3} is investigated for its dielectric and electrical properties at room temperature to study the effect of doping. The sample is characterized by X-ray diffraction and infrared spectroscopy. The size of either of volume elements of CaSiO{sub 3}:Pr{sup 3+} estimated from transmission electron microscopy is about 180–200 nm. The sample shows colossal dielectric response at room temperature. This colossal dielectric behaviour follows Debye-type relaxation and can be explained by Maxwell–Wagner (MW) polarization. However, analysis of impedance and electric modulus data using Cole–Cole plot shows that it deviates from ideal Debye behaviour resulting from the distribution of relaxation times. The distribution in the relaxation times may be attributed to existence of electrically heterogeneous grains, insulating grain boundary, and electrode contact regions. Doping, thus, results in substantial modifications in the dielectric and electrical properties of the nano-ceramic CaSiO{sub 3}.

36 MATERIALS SCIENCE↗