Search NASA⌕ Search

SEARCH · Search NASA

Results for “full scale testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Earth Entry Vehicle for Mars Sample Return

The driving requirement for design of a Mars Sample return mission is assuring containment of the returned samples. The impact of this requirement on developmental costs, mass allocation, and design approach of the Earth Entry Vehicle is significant. A simple Earth entry vehicle is described which can meet these requirements and safely transport the Mars Sample Return mission's sample through the Earth's atmosphere to a recoverable location on the surface. Detailed analysis and test are combined with probabilistic risk assessment to design this entirely passive concept that circumvents the potential failure modes of a parachute terminal descent system. The design also possesses features that mitigate other risks during the entry, descent, landing and recovery phases. The results of a full-scale drop test are summarized.

Mitcheltree, R. A.↗
NASA NTRS1978

Effect of wall thickness and material on flexural fatigue of hollow rolling elements

Hollow cylindrical bars were tested in a rolling-contact fatigue tester to determine the effects of material and outside diameter to inside diameter (OD/ID) ratios on fatigue failure mode and subsequent failure propagation. The range of applied loads with OD/ID ratios of 2.0, 1.6, 1.4, and 1.2 resulted in maximum tangential tensile stresses ranging from 165 to 655 MPa at the bore surface. Flexural failures of the hollow test bars occurred when this bore stress was 490 MPa or greater with AISI 52100 hollow bars and 338 MPa or greater with AISI M-50 hollow bars. Good correlation was obtained in relating the failures of these hollow bars with flexural failures of drilled balls from full-scale bearing test published previously.

Bamberger, E. N.↗
NASA NTRS2018

ASPIRE Aerodynamic Models and Flight Performance

NASA's Advanced Supersonic Parachute Inflation Research Experiments (ASPIRE) project was established to test full-scale supersonic parachutes at Mars-relevant conditions, as a risk-reduction activity for NASA's upcomingMars2020 mission. Deployment and inflation of Disk-Gap-Band (DGB) parachutes were examined at Mach number and dynamic pressure conditions relevant to Mars2020, using a sounding rocket platform. The flight tests examined two parachutes: a build-to-print version of the parachute used by the Mars Science Laboratory and a strengthened version of this parachute that has the same geometry but differs in materials and construction. The first flight test (SR01) of the built-to-print parachute took place on October 4, 2017, followed by the first test of the strengthened parachute during flight SR02 on March 31, 2018. A second test of the strengthened parachute with a higher target load, SR03, took place on September 7, 2018. Over the sequence of the three tests, the parachute was exposed to increasing aerodynamic loads with the peak load during SR03 being significantly larger than is expected during a Martian descent. All three tests were successful: the parachute deployment and inflation occurred at the intended conditions, the measurement systems performed as designed and provided the data, and the parachutes survived the aerodynamic loads they were exposed to. The flight tests yielded valuable data on parachute forces and high-speed imagery of the deployment and inflation process.

Parachute↗
NASA NTRS1978

Manned remote work station development article

The two prime objectives of the Manned Remote Work Station (MRWS) Development Article Study are to first, evaluate the MRWS flight article roles and associated design concepts for fundamental requirements and embody key technology developments into a simulation program; and to provide detail manufacturing drawings and schedules for a simulator development test article. An approach is outlined which establishes flight article requirements based on past studies of Solar Power Satellite, orbital construction support equipments, construction bases and near term shuttle operations. Simulation objectives are established for those technology issues that can best be addressed on a simulator. Concepts for full-scale and sub-scale simulators are then studied to establish an overall approach to studying MRWS requirements. Emphasis then shifts to design and specification of a full-scale development test article.

Source record↗
DOE OSTI2020

Advancing the science of explosive fragmentation and afterburn fireballs though experiments and simulations at the benchtop scale

Detonation of explosive devices produces extremely hazardous fragments and hot, luminous fireballs. Prior experimental investigations of these post-detonation environments have primarily considered devices containing hundreds of grams of explosives. While relevant to many applications, such large- scale testing also significantly restricts experimental diagnostics and provides limited data for model validation. As an alternative, the current work proposes experiments and simulations of the fragmentation and fireballs from commercial detonators with less than a gram of high explosive. As demonstrated here, reduced experimental hazards and increased optical access significantly expand the viability of advanced imaging and laser diagnostics. Notable developments include the first known validation of MHz-rate optical fragment tracking and the first ever Coherent Anti-Stokes Raman Scattering (CARS) measures of post-detonation fireball temperatures. While certainly not replacing the need for full-scale verification testing, this work demonstrates new opportunities to accelerate developments of diagnostics and predictive models of post-detonation environments.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
NASA NTRS2008

Practical Application of a Subscale Transport Aircraft for Flight Research in Control Upset and Failure Conditions

Over the past decade, the goal of reducing the fatal accident rate of large transport aircraft has resulted in research aimed at the problem of aircraft loss-of-control. Starting in 1999, the NASA Aviation Safety Program initiated research that included vehicle dynamics modeling, system health monitoring, and reconfigurable control systems focused on flight regimes beyond the normal flight envelope. In recent years, there has been an increased emphasis on adaptive control technologies for recovery from control upsets or failures including damage scenarios. As part of these efforts, NASA has developed the Airborne Subscale Transport Aircraft Research (AirSTAR) flight facility to allow flight research and validation, and system testing for flight regimes that are considered too risky for full-scale manned transport airplane testing. The AirSTAR facility utilizes dynamically-scaled vehicles that enable the application of subscale flight test results to full scale vehicles. This paper describes the modeling and simulation approach used for AirSTAR vehicles that supports the goals of efficient, low-cost and safe flight research in abnormal flight conditions. Modeling of aerodynamics, controls, and propulsion will be discussed as well as the application of simulation to flight control system development, test planning, risk mitigation, and flight research.

Cunningham, Kevin↗
NASA NTRS1994

Effects of scale in predicting global structural response

In the course of previous composite structures test programs, the need for and the feasibility of developing analyses for scale-up effects has been demonstrated. The analysis techniques for scale-up effects fall into two categories. The first category pertains to developing analysis methods independently for a single, unique failure mode in composites, and using this compendium of analysis methods together with a global structural model to identify and predict the response and failure mode of full-scale built-up structures. The second category of scale-up effects pertains to similitude in structural validation testing. In this latter category, dimensional analysis is used to develop scale-up laws that enable extrapolation of sub-scale component test data to full-scale structures. This viewgraph presentation describes the approach taken and some developments accomplished in the first category of analysis for scale-up effects. Layup dependence of composite material properties severely limits the use of the dimensional analysis approach and these limitations are illustrated by examples.

Kan, Han-Pin↗
NASA NTRS1972

The effects of configuration changes on the aerodynamic characteristics of a full-scale mockup of a light twin engine airplane

Wind tunnel tests of a full-scale model of a light twin engine aircraft were conducted. The angle of attack was varied from minus 4 degrees to plus 20 degrees. The sideslip range was plus or minus 8 degrees. Thrust coefficients were 0, 0.20, and 0.44. Tests were made with various nacelle configurations, modes of propeller rotation, orientation of the thrust axis, and airfoil section at Reynolds numbers of 2.96 times one million amd 2.05 times one million.

Fink, M. P.↗
NASA NTRS2014

The Max Launch Abort System - Concept, Flight Test, and Evolution

The NASA Engineering and Safety Center (NESC) is an independent engineering analysis and test organization providing support across the range of NASA programs. In 2007 NASA was developing the launch escape system for the Orion spacecraft that was evolved from the traditional tower-configuration escape systems used for the historic Mercury and Apollo spacecraft. The NESC was tasked, as a programmatic risk-reduction effort to develop and flight test an alternative to the Orion baseline escape system concept. This project became known as the Max Launch Abort System (MLAS), named in honor of Maxime Faget, the developer of the original Mercury escape system. Over the course of approximately two years the NESC performed conceptual and tradeoff analyses, designed and built full-scale flight test hardware, and conducted a flight test demonstration in July 2009. Since the flight test, the NESC has continued to further develop and refine the MLAS concept.

Gilbert, Michael G.↗
NASA NTRS1996

The smart highway project: Smart highways, smart vehicles, smart engineering

The Smart Highway project is a six mile, limited access roadway being built between Interstate 81 and Blacksburg, Virginia. The initial construction segment will be two miles long and is designed to serve as a test bed and test track for Intelligent Transportation Systems (ITS) research. The Center for Transportation Research (CTR) at Virginia Tech is developing three evaluation tools for its ITS research including DYNAVIMTS (a software framework), and the FLASH Lab (a 1/15th scale model highway and vehicle system). The Smart Highway rounds out the Center's evaluation methodology by allowing full scale operational tests, evaluations, and research under both experimental and conventional traffic conditions. Currently under development is a concept for a fully automated highway using a 'Cooperative Infrastructure Managed System' which involves ultra wide band communication beacons installed in the infrastructure with appropriate sensors, receivers and processors on board the vehicles. The project is part of the research program funded by the National Automated Highway System Consortium. The CTR hopes to develop the automated concept to prototype status by 1997. Other smart transportation and smart engineering concepts are proposed. This presentation will address the goals and objectives of the Smart Highway project, overview its status and importance to the region, and identify some of the transportation technology now under development and planned in the future.

Pethtel, Ray D.↗
NASA NTRS1999

Contributions to Active Buffeting Alleviation Programs by the NASA Langley Research Center

Buffeting is an aeroelastic phenomenon which plagues high performance aircraft, especially those with twin vertical tails like the F/A-18, at high angles of attack. This buffeting is a concern from fatigue and inspection points of view. By means of wind-tunnel and flight tests, this phenomenon is well studied to the point that buffet loads can be estimated and fatigue life can be increased by structural enhancements to the airframe. In more recent years, buffeting alleviation through active control of smart materials has been highly researched in wind-tunnel proof-of-concept demonstrations and full-scale ground tests using the F/A-18 as a test bed. Because the F/A-18 resides in fleets outside as well as inside the United States, these tests have evolved into international collaborative research activities with Australia and Canada, coordinated by the Air Force Research Laboratory (AFRL) and conducted under the auspices of The Technical Cooperation Program (TTCP). With the recent successes and advances in smart materials, the main focus of these buffeting alleviation tests has also evolved to a new level: utilize the F/A-18 as a prototype to mature smart materials for suppressing vibrations of aerospace structures. The role of the NASA Langley Research Center (LaRC) in these programs is presented.

Moses, Robert W.↗
NASA NTRS1976

Flexural fatigue of hollow rolling elements

Hollow cylindrical bars were tested in the rolling-contact fatigue tester to determine the effects of material and outside diameter to inside diameter (OD/ID) ratios of 2.0, 1.6, 1.4, and 1.2 on fatigue failure mode and subsequent failure propagation. The range of applied loads with these OD/ID ratios resulted in maximum tangential tensile stresses ranging from 165 to 655 megapascals (24,000 to 95,000 psi) at the bore surface. Flexural failures of the hollow test bars occurred when this bore stress was 490 megapascals (71,000 psi) or greater with AISI 52100 hollow bars and 338 megapascals (49,000 psi) or greater with AISI M-50 hollow bars. Good correlation was obtained in relating the failures of these hollow bars with flexural failures of drilled balls from previously published full scale bearing tests.

Bamberger, E. N.↗
NASA NTRS1980

Advanced composite elevator for Boeing 727 aircraft, volume 2

Preliminary design activity consisted of developing and analyzing alternate design concepts and selecting the optimum elevator configuration. This included trade studies in which durability, inspectability, producibility, repairability, and customer acceptance were evaluated. Preliminary development efforts consisted of evaluating and selecting material, identifying ancillary structural development test requirements, and defining full scale ground and flight test requirements necessary to obtain Federal Aviation Administration (FAA) certification. After selection of the optimum elevator configuration, detail design was begun and included basic configuration design improvements resulting from manufacturing verification hardware, the ancillary test program, weight analysis, and structural analysis. Detail and assembly tools were designed and fabricated to support a full-scope production program, rather than a limited run. The producibility development programs were used to verify tooling approaches, fabrication processes, and inspection methods for the production mode. Quality parts were readily fabricated and assembled with a minimum rejection rate, using prior inspection methods.

Chovil, D. V.↗
NASA NTRS1963

CHARACTERISTICS OF LIFTING-FAN V/STOL AIRCRAFT

Wind-tunnel tests of full scale practical configuration of lifting fan v/stol aircraft show transition pitching moments comparable to conventional aircraft, and that lift increases with greater forward speed

LIFT FAN↗
NASA NTRS2014

Blade Motion Correlation for the Full-Scale UH-60A Airloads Rotor

Testing was successfully completed in May 2010 on a full-scale UH-60A rotor system in the USAF's National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel.[1] The primary objective of this NASA Army sponsored test program was to acquire a comprehensive set of validation-quality measurements ona full-scale pressure-instrumented rotor system at conditions that challenge the most sophisticated modeling andsimulation tools. The test hardware included the same rotor blades used during the UH-60A Airloads flight test.[2] Key measurements included rotor performance, blade loads, blade pressures, blade displacements, and rotorwake measurements using large-field Particle Image Velocimetry (PIV) and Retro-reflective Background Oriented Schlieren (RBOS).

Airloads Rotor↗
NASA NTRS1981

Designing for aircraft structural crashworthiness

This report describes structural aviation crash dynamics research activities being conducted on general aviation aircraft and transport aircraft. The report includes experimental and analytical correlations of load-limiting subfloor and seat configurations tested dynamically in vertical drop tests and in a horizontal sled deceleration facility. Computer predictions using a finite-element nonlinear computer program, DYCAST, of the acceleration time-histories of these innovative seat and subfloor structures are presented. Proposed application of these computer techniques, and the nonlinear lumped mass computer program KRASH, to transport aircraft crash dynamics is discussed. A proposed FAA full-scale crash test of a fully instrumented radio controlled transport airplane is also described.

Thomson, R. G.↗
NASA NTRS1995

A record of all marker bands found in the upper rivet rows of 2 adjacent bays from a fuselage lap splice joint

A full scale fuselage test article was subjected to 60,000 load cycles (pressurizations) to study the effect of widespread fatigue damage in fuselage structures. Every 10,000 cycles coded marker block loading sequences were used to mark the fracture surfaces of the fatigue cracks propagating within the panel. The loading sequences consisted of series of underloads combined with a series of full pressurizations. The combination of loads and underloads marked the fracture surfaces with marker bands that could later be used to reconstruct the fatigue crack growth history of selected regions within the test article. Thirty rivet holes comprising the upper rivet rows from two adjacent bays (bays #3 and #4) from a fuselage lap splice joint were examined for the purpose of this study. Optical and scanning electron microscopy (SEM) were used to locate the marker bands.

Willard, Scott A.↗
NASA NTRS2003

Calculation of Rotor Performance and Loads Under Stalled Conditions

Rotor behavior in stalled conditions is investigated using wind tunnel test data of a l/l0-scale CH-47B/C type rotor, which provides a set of test conditions extending from unstalled to light stall to some deep stall conditions over a wide range of advance ratios. The rotor performance measured in the wind tunnel is similar to the main rotor performance measured during the NASA/Army UH-60A Airloads Program, although the two rotors are quite different. The analysis CAMRAD II has been used to predict the rotor performance and loads. Full-scale airfoil test data are corrected for Reynolds number effects for comparison with the model-scale rotor test. The calculated power coefficient shows good correlation with the measurements below stall with the Reynolds number-corrected airfoil table. Various dynamic stall models are used in the calculations. The Boeing model shows the lift augmentation at low advance ratios and the Leishman-Beddoes model shows better correlation of torsion moment than the other models at mu = 0.2. However, the dynamic stall models, in general, show only a small influence on the rotor power and torsion moment predictions especially at higher advance ratios.

Yeo, Hyeonsoo↗