Search NASA⌕ Search

SEARCH · Search NASA

Results for “hover”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Analysis of pilot-aircraft performance and reliability via the application of man-machine models

The present approach to analytic modeling, which utilizes human response theory together with modern control theory, is discussed. Analytic modeling of human performance has progressed to the point where it can be used with some confidence in the design and performance analysis of man-machine systems. An example of its use in helping design a flight director for the hover control of a VTOL vehicle is described. How the method could be used for analysis of human response to system failure is sketched.

Kleinman, D. L.↗
NASA NTRS1977

Tail contribution to the directional aerodynamic characteristics of a 1/6-scale model of the rotor systems research aircraft with a tail rotor

The results are presented of a wind tunnel investigation to determine the tail contribution to the directional aerodynamic characteristics of a 1/6-scale model of the rotor systems research aircraft (RSRA) with a tail rotor. No main rotor was used during the investigation. Data were obtained with and without the tail rotor over a range of sideslip angle and over a range of rotor collective pitch angle. The model with the tail rotor was tested at several advance ratios with and without thrust from the auxiliary thrust engines on the RSRA fuselage. Increasing the space between the tail-rotor hub and the vertical tail reduced the tail-rotor torque required at moderate to high rotor thrust. Increasing the exit dynamic pressure of the auxiliary thrust engines decreases the tail contribution to the static directional stability. The tail-rotor thrust and its interference provide a positive increment to the static directional stability. The tail contribution increases with forward speed. The adverse yawing moment of the airframe would strongly affect the thrust required of the tail rotor when the helicopter is hovering in a crosswind.

Mineck, R. E.↗
NASA NTRS1977

Helicopter optimal descent and landing after power loss

An optimal control solution is obtained for the descent and landing of a helicopter after the loss of power in level flight. The model considers the helicopter vertical velocity, horizontal velocity, and rotor speed; and it includes representations of ground effect, rotor inflow time lag, pilot reaction time, rotor stall, and the induced velocity curve in the vortex ring state. The control (rotor thrust magnitude and direction) required to minimize the vertical and horizontal velocity at contact with the ground is obtained using nonlinear optimal control theory. It is found that the optimal descent after power loss in hover is a purely vertical flight path. Good correlation, even quantitatively, is found between the calculations and (non-optimal) flight test results.

Johnson, W.↗
NASA NTRS1977

Load and stability measurements on a soft-inplane rotor system incorporating elastomeric lead-lag dampers

An experimental investigation was conducted of the dynamic response and inplane stability associated with a new soft-inplane helicopter rotor. The unique feature of this rotor was the use of an internal elastomeric damper to restrain the blade inplane motion about the lead-lag hinge. The properties of the elastomer were selected to provide both a nominal first inplane frequency ratio of 0.65 and sufficient damping to eliminate the need for additional external damping sources to prevent ground resonance on a typical fuselage structure. For this investigation a 1/5-scale aeroelastic model was used to represent the rotor. The four-blade model had a diameter of 3.05 m (10 ft) and a solidity of 0.103. The first out-of-plane frequency ratio was 1.06. The model was tested in hover and in forward flight up to an advance ratio of 0.45. At each forward speed the rotor lift was varied up to simulated maneuver conditions. The measured rotor loads and response were within acceptable limits, and no adverse response qualities were observed. Moderate out-of-plane hub moments were measured, even for zero lift, to indicate the beneficial control power available for this design. Blade inplane stability testing indicated that the rotor system damping remained at moderate levels throughout the operating envelope.

Weller, W. H.↗
NASA NTRS1977

Flight investigation of a vertical-velocity command system for VTOL aircraft

A flight investigation was undertaken to assess the potential benefits afforded by a vertical-velocity command system (VVCS) for VTOL (vertical take-off and landing) aircraft. This augmentation system was conceived primarily as a means of lowering pilot workload during decelerating approaches to a hover and/or landing under category III instrument meteorological conditions. The scope of the investigation included a determination of acceptable system parameters, a visual flight evaluation, and an instrument flight evaluation which employed a 10 deg, decelerating, simulated instrument approach task. The results indicated that the VVCS, which decouples the pitch and vertical degrees of freedom, provides more accurate glide-path tracking and a lower pilot workload than does the unaugmented system.

Kelly, J. R.↗
NASA NTRS1976

Solving the optimal attention allocation problem in manual control

Within the context of the optimal control model of human response, analytic expressions for the gradients of closed-loop performance metrics with respect to human operator attention allocation are derived. These derivatives serve as the basis for a gradient algorithm that determines the optimal attention that a human should allocate among several display indicators in a steady-state manual control task. Application of the human modeling techniques are made to study the hover control task for a CH-46 VTOL flight tested by NASA.

Kleinman, D. L.↗
NASA NTRS1977

Optimal control alleviation of tilting proprotor gust response

Optimal control theory is applied to the design of a control system for alleviation of the gust response of tilting proprotor aircraft. Using a proprotor and cantilever wing analytical model, the uncontrolled and controlled gust response is examined over the entire operating range of the aircraft except for hover: helicopter mode, conversion, and airplane mode flight. Substantial improvements in the loads, ride quality, and aeroelastic stability are possible with a properly designed controller. A single controller, nominally optimal only at the design point speed (160 knots here), operated efficiently over the entire speed range, with the possible exception of very low speed in helicopter mode. Kalman-Bucy filters were used as compensation networks to provide state estimates from various measurements in the system. Efficient control requires the measurement of the wing motion, rotor speed perturbation, and tip-path-plane tilt.

Johnson, W.↗
NASA NTRS1976

Aeroelastic stability of complete rotors with application to a teetering rotor in forward flight

The derivation of a set of nonlinear coupled flap-lag-torsion equations of motion for moderately large deflections of an elastic, two bladed teetering helicopter rotor in forward flight is concisely outlined. The following degrees of freedom are included in the mathematical model: rigid body flapping, rigid body lead lag, elastic bending in flap and lead-lag blade root torsion and shaft torsion. Quasi-steady aerodynamic loads are considered and the effects of reversed flow are included. The aeroelastic stability of the complete rotor is investigated using a linearized system of equations of motion. The equilibrium position about which the equations are linearized is obtained by considering the trim state of the helicopter, in true or simulated forward flight conditions. The sensitivity of the aeroelastic stability boundaries to interblade structural and mechanical coupling is illustrated by comparing the complete rotor stability boundaries with those obtained from a single blade analysis for a number of hover and forward flight cases.

Shamie, J.↗
NASA NTRS1977

Tenth-scale powered model test of a tilt-nacelle V/STOL airplane

Wind tunnel and ground static tests of a tenth scale powered model of a lift/cruise fan airplane have been conducted to define its low speed performances and handling qualities. The model was powered by three 5.5-in diameter turbopowered simulators; one located in the forebody while the remaining two were installed in tilting nacelles mounted on the aft body. Results are presented for static hover tests in ground effects with the model configured for VTOL operations and at forward speeds with the model configured for loiter, short takeoff, and VTOL operations.

Omar, M. E.↗
NASA NTRS1977

Analysis of control concepts for gas and shaft-coupled V/STOL aircraft lift fan systems

V/STOL aircraft rely on their propulsion systems to provide lift and attitude control moments during hover and low-speed flight. For lift-fan powered V/STOL aircraft, two unconventional propulsion system types have been proposed. The first type uses fans connected by hot gas ducting, and the second type uses fans connected by cross shafting. This paper presents results of an analytical study which identifies the basic steady-state and dynamic characteristics for each type of system. For the gas-coupled system, the control concepts analyzed were variable-area fan turbines and throttling valves in the ducting. For the shaft-coupled system, the control concepts analyzed were variable-pitch fans and variable fan inlet guide vanes. All of these concepts are shown to be capable of meeting V/STOL aircraft control moment and transient response requirements when appropriate propulsion controls are used. Each type of system has unique problem areas which require an integrated approach to aircraft/propulsion control design.

Sellers, J. F.↗
NASA NTRS1977

Experimental investigations of thrust vectoring systems for VTOL aircraft

This paper presents a summary of two technology programs sponsored by NASA to investigate the characteristics of two thrust vectoring schemes for V/STOL aircraft. The operational capability of the VTOL aircraft is dependent on maximum utilization of the installed thrust in both the cruise and powered lift modes of flight. An effective thrust vectoring system on the cruise propulsion unit is therefore essential to provide maximum payload in hover and STOL plus minimum specific fuel consumption in loiter and cruise. Introducing a high by-pass ratio fan system, augmenting the gas generator thrust, as the propulsion system for VTOL aircraft places increased significance on the performance of the relatively short coupled thrust vectoring systems. The two programs discussed herein include both large-scale and small-scale tests of a vectoring hood system with a vented, internal-lip and swivel nozzle systems. These tests indicated that a satisfactory thrust vectoring system can be developed.

Rolls, L. S.↗
NASA NTRS1977

Theoretical study of hull-rotor aerodynamic interference on semibuoyant vehicles

Theoretical methods are being developed to predict the mutual interference between rotor wakes and the hull for semibuoyant vehicles. The objective of the investigation is to predict the pressure distribution and overall loads on the hull in the presence of rotors whose locations, tilt angles, and disk loading are arbitrarily specified. The methods involve development of potential flow models for the hull alone in a nonuniform onset flow, a rotor wake which has the proper features to predict induced flow outside the wake, and a wake centerline specification technique which accounts for the reactions of the wake to a nonuniform crossflow. The flow models are used in sequence to solve for the mutual influence of the hull and rotor(s) on each other and the resulting loads. A flow separation model is included to estimate the influence of separation on hull loads at high sideslip angles. Only limited results have been obtained to date. These were obtained on a configuration which was tested in the Ames Research Center 7- by 10-Foot Low Speed Tunnel under Goodyear Aircraft Corporation sponsorship and indicate the nature of the interference pressure distribution on a configuration in hover.

Spangler, S. B.↗
NASA NTRS1977

Aeroelastic stability of complete rotors with application to a teetering rotor in forward flight

The derivation of a set of non-linear coupled flap-lag-torsion equations of motion for moderately large deflections of an elastic, two-bladed teetering helicopter rotor in forward flight is concisely outlined. The following degrees of freedom are included in the mathematical model: rigid body flapping, rigid body lead-lag, elastic bending in flap and lead-lag, blade root torsion, and shaft torsion. Quasi-steady aerodynamic loads are considered and the effects of reversed flow are included. The aeroelastic stability of the complete rotor is investigated by using a linearized system of equations of motion. The equilibrium position about which the equations are linearized is obtained by considering the trim state of the helicopter, in true or simulated forward flight conditions. The sensitivity of the aeroelastic stability boundaries to interblade structural and mechanical coupling is illustrated by comparing the complete rotor stability boundaries with those obtained from a single blade analysis for a number of hover and forward flight cases.

Shamie, J.↗
NASA NTRS1978

Helicopter position stabilizing system

System utilizes vertical gyroscope mounted on telescope handled by onboard observer, to help helicopter pilot fly precise circles over ground target without use of ground observer. Other possible uses include cargo discharge or pickup without ground controller, and hovering over invisible target with known coordinates.

Jenkin, K. R.↗
NASA NTRS1977

Wind-tunnel tests of wide-chord teetering rotors with and without outboard flapping hinges

Wind tunnel tests of aeroelastically designed helicopter rotor models were conducted to obtain rotor aerodynamic performance and dynamic response data pertaining to two-bladed teetering rotors with a wider chord and lower hover tip speed than currently employed on production helicopters. The effects of a flapping hinge at 62 percent radius were also studied. Finally, the effects of changing tip mass on operating characteristics of the rotor with the outboard flapping hinge were examined. The models were tested at several shaft angles of attack for five advance ratios, 0.15, 0.25, 0.35, 0.40, and 0.45. For each combination of shaft angle and advance ratio, the rotor lift was varied over a wide range to include simulated maneuver conditions. At each test condition, rotor aerodynamic performance and dynamic response data were obtained. From these tests, it was found that wide-chord rotors may be subject to large control forces. An outboard flapping hinge may be used to reduce beamwise bending moments over a significant part of the blade radius without significantly affecting the chordwise bending moments.

Weller, W. H.↗
NASA NTRS1977

Capabilities of the Navy variable stability X-22A for V/STOL flying qualities R and D

The X-22A V/STOL Flight Research Facility which provides in-flight simulation capability applicable to hover, low speed, and transition flight investigation of fixed wing V/STOL flying is described. The variable stability system, the guidance and display equipment, the data acquisition and processing system, and the ground simulator are included. Research programs involving the STOL flying qualities for landing approach, the control system, display, and guidance requirements for VTOL aircraft instrument approach and landing, and the expansion of the adverse weather operation capabilities of the Navy's VTOL aircraft are briefly summarized.

Aiken, E. W.↗
NASA NTRS1977

Pilot centered requirements in control/display design

A method developed for predicting pilot opinion ratings for particular vehicles and tasks using optimal control pilot model is described and an outline of a flight director design procedure based upon the optimal control pilot model is given. Longitudinal and lateral control of a helicopter in hover and in a -6 deg constant ground speed-command landing approach are considered. Emphasis is placed on display design for optimum V/STOL control.

Hess, R. A.↗
NASA NTRS1977

Survey of piloting factors in V/STOL aircraft with implications for flight control system design

Flight control system design factors involved for pilot workload relief are identified. Major contributors to pilot workload include configuration management and control and aircraft stability and response qualities. A digital fly by wire stability augmentation, configuration management, and configuration control system is suggested for reduction of pilot workload during takeoff, hovering, and approach.

Ringland, R. F.↗