Search NASA⌕ Search

SEARCH · Search NASA

Results for “protons”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Proton radiation effects on electronic defect states in MOCVD-grown (010) β -Ga 2 O 3

The impact of 1.8 MeV proton irradiation on metalorganic chemical vapor deposition grown (010) β-Ga 2 O 3 Schottky diodes is presented. It is found that after a 10.8 × 10 13 cm –2 proton fluence the Schottky barrier height of (1.40 ± 0.05 eV) and the ideality factor of (1.05 ± 0.05 ) are unaffected. Capacitance–voltage extracted net ionized doping curves indicate a carrier removal rate of 268 ± 10 cm –1 . The defect states responsible for the observed carrier removal are studied through a combination of deep level transient and optical spectroscopies (DLTS/DLOS) as well as lighted capacitance–voltage (LCV) measurements. The dominating effect on the defect spectrum is due to the E c -2.0 eV defect state observed in DLOS and LCV. This state accounts for ~75 % of the total trap introduction rate and is the primary source of carrier removal from proton irradiation. Of the DLTS detected states, the E c -0.72 eV state dominated but had a comparably smaller contribution to the trap introduction. These two traps have previously been correlated with acceptor-like gallium vacancy-related defects. Several other trap states at E C -0.36, E C -0.63, and E C -1.09 eV were newly detected after proton irradiation, and two pre-existing states at E C -1.2 and E C -4.4 eV showed a slight increase in concentration after irradiation, together accounting for the remainder of trap introduction. However, a pre-existing trap at E c -0.40 eV was found to be insensitive to proton irradiation and, therefore, is likely of extrinsic origin. Furthermore, the comprehensive defect characterization of 1.8 MeV proton irradiation damage can aid the modeling and design for a range of radiation tolerant devices.

42 ENGINEERING↗

Characterization of laser-accelerated proton beams from a 0.5 kJ sub-picosecond laser for radiography applications

Laser-accelerated ion beams show promise for many applications, including high-resolution flash imaging of static or dynamic objects in next-generation radiography to probe materials and plasmas in extreme environments and inertial confinement fusion. To scale up ion beam production for radiography applications, we conducted experiments using sub-picosecond lasers up to 0.5 kJ at the OMEGA-EP facility to characterize proton beams from solid targets, primarily CH/CD sub-micron thin films from which ion beams were also used for static and dynamic radiography for the first time. For standalone sub-micron thin CH films, the highest detected proton energy is in the range of 72–97 MeV. Proton beams with highest energy near or above 60 MeV at full laser energy and similar beam profiles are also measured from low-density CD foams and flat CH foil target of micrometer-scale thickness. The ~ 700–800 nm CH/CD foils achieve the highest ion yield among the targets tested. For sub-micron thin films, the laser prepulse can expand the target and lead to complex interactions, which is simulated using coupled hydrodynamic and two-step kinetic models. Simulations suggest the presence of a micrometer-scale preplasma plateau with near-critical density and further indicate that target normal sheath acceleration, electron heating from Relativistic transparency in the preplasma plateau, and background proton reflection from carbon ion front at the rear side contribute to the resulting proton spectrum from these sub-micron thin targets at various stages. These proton beams show strong potential for radiography and for production of secondary sources.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Demonstration of improvement of energy conversion rate from kJ PW laser to protons with electron confinement

Kilojoule-class relativistic intensity lasers can produce energetic protons with high energy conversion efficiencies in the interaction with a thin foil target. Using the national ignition facility advanced radiographic capability (NIF-ARC) laser, we demonstrated an enhancement of energy conversion from laser to protons by the effective confinement of fast electrons in the laser spot by random kicks from the self-excited field. The number of fast electrons was increased by 4.6 times by increasing the ratio of the laser spot size to the foil thickness to strengthen the confinement effect. The energy conversion efficiency from laser to protons increases approximately linearly with the enhancement of the number of fast electrons. The conversion rate for protons with energies above 8 MeV was 1.8 %. The result leads to high efficiency proton acceleration which is beneficial in applications, such as proton radiography and plasma heating in laser fusion.

Physics↗

Fast rotation of nuclei with extreme isospin in the vicinity of neutron and proton drip lines

Abstract The analysis of the present understanding of collective rotation in very neutron-rich nuclei is presented. It is shown that collective rotation can lead to the increase of stability of rotational states with increasing spin. The detailed investigation of rotational excitations in very proton-rich nuclei confirms this conclusion and indicates that experimental studies of such features are more feasible in the nuclei near proton drip line. They also show that rotational bands which are proton quasi-bound at zero or low spins can be transformed into proton bound ones at high spin by collective rotation of nuclear systems. This is due to strong Coriolis interaction which acts on high-jor strongly mixed M orbitals and drives the highest in energy occupied single-particle states into negative energy domain. These physical mechanisms lead to a substantial extension of the nuclear landscape beyond the spin zero proton drip line. In addition, a new phenomenon of the formation of giant proton halos in rotating nuclei emerges: it is triggered by the occupation of strongly mixed M intruder orbitals.

Physics↗

Proton transparency and neutrino physics: New methods and modeling

Extracting accurate results from neutrino oscillation and cross section experiments requires accurate simulation of the neutrino-nucleus interaction. The rescattering of outgoing hadrons (final state interactions) by the rest of the nucleus is an important component of these interactions. We present a new measurement of proton transparency (defined as the fraction of outgoing protons that emerge without significant rescattering) using electron-nucleus scattering data recorded by the CLAS detector at Jefferson Laboratory on helium, carbon, and iron targets. This analysis uses a new data-driven method to extract the transparency. It defines transparency as the ratio of electron-scattering events with a detected proton to quasi-elastic electron-scattering events where a proton should have been knocked out. Our results are consistent with previous measurements that determined the transparency from the ratio of measured events to theoretically predicted events. We find that the GENIE event generator, which is widely used by oscillation experiments to simulate neutrino-nucleus interactions, needs to better describe both the nuclear ground state and proton rescattering in order to reproduce our measured transparency ratios, especially at lower proton momenta.

direct reactions↗

Proton pairing in neutron stars from chiral effective field theory

Here, we study the 1 S 0 proton pairing gap in beta-equilibrated neutron star matter within the framework of chiral effective field theory. We focus on the role of three-body forces, which strongly modify the effective proton-proton spin-singlet interaction in dense matter. We find that three-body forces generically reduce both the size of the pairing gap and the maximum density at which proton pairing may occur. The pairing gap is computed within BCS theory using a single-particle dispersion relation calculated up to second order in perturbation theory. Model uncertainties are estimated by varying the nuclear potential (its order in the chiral expansion and high-momentum cutoff) and the choice of single-particle spectrum in the gap equation. We find that a second-order perturbative treatment of the single-particle spectrum suppresses the proton 1 S 0 pairing gap relative to the use of a free spectrum. We estimate the critical temperature for the onset of proton superconductivity to be T c = (3:2–5:1) 10 9 K, which is consistent with previous theoretical results in the literature and marginally within the range deduced from a recent Bayesian analysis of neutron star cooling observations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Proton decays in 16 Ne and 18 Mg and isospin-symmetry breaking in carbon isotopes and isotones

We report that proton-rich nuclei possess unique properties in the nuclear chart. Due to the presence of both continuum coupling and Coulomb interaction, phenomena such as halos, Thomas-Ehrman shift, and proton emissions can occur. Relevant experimental data are difficult to obtain, so that theoretical calculations are needed to understand nuclei at drip lines and to guide experimentalists. In particular, the 16 Ne and 18 Mg isotopes are supposed to be one-proton and/or two-proton emitting nuclei, but associated experimental data are either incomplete or even unavailable. Consequently, we performed Gamow shell model calculations of carbon isotones bearing A = 15 - 18 . Isospin-symmetry breaking occurring in carbon isotones and isotopes is also discussed. It is hereby shown that the mixed effects of continuum coupling and Coulomb interaction at drip lines generate complex patterns in isospin multiplets. Added to that, it is possible to determine the one-proton and two-proton widths of 16 Ne and 18 Mg . Obtained decay patterns are in agreement with those obtained in previous experimental and theoretical works. Moreover, to our knowledge, this is the first theoretical calculation of binding energy and partial decay widths of 18 Mg in a configuration interaction picture.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Observation of a Near-Threshold Proton Resonance in 11 B

A near-threshold proton resonance in 11 B at 𝐸 ex = 11.44 ± 0.04 MeV is observed via the reaction 10 Be⁢(𝑑,𝑛)⁢ 11 B → 10 Be + 𝑝 in inverse kinematics, measured with a beam of the radioactive isotope 10 Be. The resonance energy at 𝐸 res = 211⁢(40) keV is consistent with a proton signal observed by Ayyad et al. in the 𝛽-delayed proton decay of 11 Be. By comparison to a distorted wave Born approximation calculation, a 0.27(6) spectroscopic factor is extracted and a tentative (ℓ = 0) character is assigned for this resonance. The significant cross section in the proton-transfer (𝑑,𝑛) reaction, as well as the observation of its proton-decay signal, point to the threshold-resonance character of this state. The position of this state, its structure, and strong coupling to the 𝑠-wave continuum represent an ideal case to study quantum near-threshold many-body dynamics of unstable states. In conclusion, the presence of this state is an important step toward understanding the excessively large beta-delayed proton-decay branch of 11 Be.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Beam Energy Dependence of Fifth- and Sixth-Order Net-Proton Number Fluctuations in Au + Au Collisions at RHIC

We report the beam energy and collision centrality dependence of fifth and sixth order cumulants (C 5 , C 6 ) and factorial cumulants (κ 5 , κ 6 ) of net-proton and proton distributions, from $\sqrt{s_{NN}}$=3-200 GeV Au+Au collisions at RHIC. The net-proton cumulant ratios generally follow the hierarchy expected from QCD thermodynamics, except for the case of collisions at $\sqrt{s_{NN}}$ = 3 GeV. C 6 /C 2 for 0-40\% centrality collisions is increasingly negative with decreasing $\sqrt{s_{NN}}$, while it is positive for the lowest $\sqrt{s_{NN}}$ studied. These observed negative signs are consistent with QCD calculations (at baryon chemical potential, μ B ≤ 110 MeV) that include a crossover quark-hadron transition. In addition, for $\sqrt{s_{NN}}$≥ 11.5 GeV, the measured proton κ n , within uncertainties, does not support the two-component shape of proton distributions that would be expected from a first-order phase transition. Taken in combination, the hyper-order proton number fluctuations suggest that the structure of QCD matter at high baryon density, μ B ~750 MeV ($\sqrt{s_{NN}}$ = 3 GeV) is starkly different from those at vanishing μ B ~20MeV ($\sqrt{s_{NN}}$ = 200 GeV and higher).

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Proton branching ratios in 22 Mg for X-ray bursts

Here, decay protons from 22 Mg energy levels populated through a previously reported 24 Mg(p, t) 22 Mg transfer reaction (Chae et al. in Phys Rev C 79:055804, 2009) have been analyzed for proton branching ratios as a follow-up analysis. The measurement was performed at the Holifield Radioactive Ion Beam Facility of Oak Ridge National Laboratory by utilizing 41-MeV proton beams and 24 Mg solid targets. Decay protons and reaction tritons were simultaneously detected with a silicon detector array. By investigating the 24 Mg(p, t) 22 Mg*(p) 21 Na channels, the proton branching ratios of five 22 Mg excited states were obtained. The measured branching ratios provide constraints on the proton partial widths of the populated 22 Mg levels, which have implications for X-ray burst nucleosynthesis.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Model-independent extraction of the proton charge radius from PRad data

The proton radius puzzle has motivated several new experiments that aim to extract the proton charge radius and resolve the puzzle. Recently, PRad, a new electron–proton scattering experiment at Jefferson Lab, reported a proton charge radius of [Formula: see text]. The value was obtained by using a rational function model for the proton electric form factor. We perform a model-independent extraction using [Formula: see text]-expansion of the proton charge radius from PRad data. We find that the model-independent statistical error is more than 50% larger compared to the statistical error reported by PRad.

Astronomy & Astrophysics↗

Influence of Proton Activity Gaps between Electrodes on Open-Circuit Potential of H 2 /H 2 and H 2 /Air Cells

Polymer -electrolyte-fuel-cell open-circuit voltages (OCVs) are exactly defined by equation (1), where cathode and anode proton activities [(aH+)cathode and (aH+)anode, respectively] usually are identical, so the third term in the right-hand side of equation (2) is ignored. OCV=E0+RT/2F*ln(a1/2 O2*(a2 H+)cathode/aH2O)-RT/2F*ln((a2 H+)anode/aH2) (1) =E0+RT/2F*ln(a1/2 O2*aH2/aH2O)+RT/2F*ln((a2 H+)cathode/(a2 H+)anode) (2) Water vapor pressure is a colligative property that fundamentally correlates to electrolyte concentrations in aqueous solutions. Proton activity is a function of acid concentration, such as pH, when electrolytes are acids. In polymer-electrolyte membranes, water vapor pressure and acid concentration are understood as relative humidity (RH) and water uptake (λ), respectively, where λ represents number of water molecules per sulfonic acid molecule. Several investigations have reported the relationship between RH and λ, meaning that proton activities and associated water uptakes are intimately related to RH. In actual fuel cell operation, cathode RH is determined by ambient-atmosphere and/or humidifier RH(s), and anode RH depends on hydrogen-circulator RH. Therefore, RH is not always identical at both electrodes, and the difference between electrode RHs is considerable during dry operation of polymer electrolyte fuel cells. Therefore, the third term in the right-hand side of equation (2) may be significant for dry operation. We measured OCVs when hydrogen was supplied to both electrodes at 80°C. One electrode (A) was fixed at 30% RH, while RH at the other electrode (B) was varied (0, 5, 10, 20, and 30%). Measured OCVs varied from 0 to 75 mV. For fuel cell tests, electrode A was supplied with hydrogen at 30% RH; electrode B, oxygen at 0, 5, 10, 20, and 30% RH. OCVs deviated from that measured when RH at electrode B was 30%, increasing from 0 to 60 mV with decreasing RH at electrode B. Results are also shown in Figure 1. Proton activities of both electrodes were thermodynamically calculated. The Gibbs–Duhem relation was applied to obtain molar Gibbs free energies of water and sulfonic acid, and proton activity coefficient was calculated using the Gibbs free energy of sulfonic acid and the relationship between RH and λ1–4, assuming that protons and sulfonic anions show identical ionic-activity coefficients. OCVs were estimated using the third term in the right-hand side of equation (2). Results are shown in Figure 1. Fuel-cell current–voltage performance was poor when RHs at the anode and cathode were 30 and 20%, respectively. To determine kinetic current, we measured the oxygen-reduction reaction (ORR) using a rotating-disk electrode (RDE) in concentrated-acid aqueous solutions, which modeled catalyst-layer ionomers. Kinetic currents decreased with acid concentrations. References T. A. Zawodzinski, Jr., C. Derouin, S. Radzinski, R. J. Sherman, V. T. Smith, T. E. Springer and S. Gottesfeld , J. Electrochem. Soc., 140,1041 (1993) P. K. Das and A. Z. Weber, Proceedings of the ASME 2013 11th Fuel Cell Science, Engineering and Technology Conference, Fuel Cell 18010 (2013) V. A. Sethuraman, J. W. Weidner, A. T. Haug, S. Motupally,b and L. V. Protsailo, J. Electrochem. Soc., 155, B50 (2008) A. Kusoglu and A. Z. Weber, Chem. Rev., 117, 987 (2017) Figure 1

Yoshida, Toshihiko↗

Impact of Proton Activity on Fuel-Cell Performance (CRADA Final Report)

The key attribute that is being investigated is the dependence of the oxygen-reduction and hydrogen-oxidation reaction kinetics on proton activity. The influence of proton activity on the kinetics is also important in the determination of limiting factors that impact overall fuel-cell performance. At lower humidities, which are required to simplify fuel-cell water and thermal management (especially for higher-temperature operation) and enable next generation fuel cells, the ionomer water content will be different than that in today’s fuel cells. Such changes in water content directly impact the activity and concentration of protons. Thus, it is necessary to quantify this impact of proton activity on the reaction kinetics, and to determine means to mitigate any detrimental impacts to enable high performance. To realize the above goals of understanding the intrinsic interactions of proton activity on hydrogen-oxidation and oxygen-reduction kinetics, systematic investigations were carried out and a novel technique, a rapid microelectrode with environmental control, was realized. The experimental campaign at LBNL worked alongside that of TokyoTech and both were complemented by mathematical modeling of the key phenomena. The results demonstrated a robust method to analyze the kinetic behavior and an impact of proton activity, although greater delineation in terms of ion concentration versus activity was not obtained fully due in part to limited lab access during the COVID pandemic.

30 DIRECT ENERGY CONVERSION↗

Focussing Protons from a Kilojoule Laser for Intense Beam Heating Using Proximal Target Structures

Proton beams driven by chirped pulse amplified lasers have multi-picosecond duration and can isochorically and volumetrically heat material samples, potentially providing an approach for creating samples of warm dense matter with conditions not present on Earth. Envisioned on a larger scale, they could heat fusion fuel to achieve ignition. We have shown in an experiment that a kilojoule-class, multi-picosecond short pulse laser is particularly effective for heating materials. The proton beam can be focussed via target design to achieve exceptionally high flux, important for the applications mentioned. The laser irradiated spherically curved diamond-like-carbon targets with intensity 4×10 18 W/cm 2 , producing proton beams with 3MeV slope temperature. A Cu witness foil was positioned behind the curved target, and the gap between was either empty or spanned with a structure. With a structured target, the total emission of Cu Kα fluorescence was increased 18 fold and the emission profile was consistent with a tightly focussed beam. Transverse proton radiography probed the target with ps order temporal and 10 μm spatial resolution, revealing the fast-acting focussing electric field. Complementary particle-in-cell simulations show how the structures funnel protons to the tight focus. The beam of protons and neutralizing electrons induce the bright Kα emission observed and heat the Cu to 100eV.

47 OTHER INSTRUMENTATION↗

Observations of proton spectra /Ep ranging from 1.0 to 300 keV/ and fluxes at the plasmapause.

Discussion of proton flux data recorded for 32 samples per spin period by two solid state proton detectors and a three-axis fluxgate magnetometer aboard Explorer 45 which was launched from Kenia into a 220-km-to-5.24 earth radius orbit. The occurrence of an amplifier saturation effect in the presence of high energy protons is noted. Diagrams are included for proton intensities, proton differential flux vs altitude in six energy bands, evolution of proton differential energy spectra through a steep gradient region, omnidirectional fluxes vs altitude, and plasma densities.

Williams, D. J.↗

High-energy proton radiation belt.

The experiments and theories to explain the high-energy protons trapped in the earth's radiation belt are reviewed. The theory of cosmic ray albedo neutron decay injection of protons into the radiation belt is discussed. Radial diffusion and change in the earth's dipole moment are considered along with losses of protons by ionization and nuclear collision. It is found that the measured albedo neutron escape current is sufficient to supply trapped protons above 30 MeV. The theoretical calculations of the trapped protons are in agreement with the measurements for L less than or equal to 1.7 both on and off the equator. For L greater than or equal to 1.7, additional trapped proton differential energy measurements should be made before the theory can be adequately tested. It appears that an additional loss mechanism such as pitch angle scattering may be required.

White, R. S.↗

On the anisotropies of interplanetary low-energy proton intensities

Explorer 35 proton anisotropic flux data (proton energies between 0.3 and 6.3 MeV) and simultaneous magnetic field measurements were used to supply more information on the propagation characteristics of low-energy protons in the interplanetary medium. During the rising portions of the proton events, large field-aligned anisotropies were observed. During the decaying part of the proton events, either radial anisotropy or near-isotropy was noticed. In addition, certain observations made during the decaying part of the proton events revealed anisotropies deviating significantly from the radial direction.

Pesses, M. E.↗

Ring current proton decay by charge exchange

Explorer 45 (S3-A) measurements were made during the recovery phase of the moderate magnetic storm of February 24, 1972, in which a symmetric ring current had developed and effects due to asymmetric ring current losses could be eliminated. It was found that after the initial rapid decay of the proton flux, which is a consequence of the dissipation of the asymmetric ring current, the equatorially mirroring protons in the energy range 5-30 keV decayed throughout the L value range of 3.5-5.0 at the charge exchange decay rate calculated by Liemohn (1961). After several days of decay, the proton fluxes reached a lower limit where an apparent equilibrium was maintained, between weak particle source mechanisms and the loss mechanisms, until fresh protons were injected into the ring current region during substorms. While other proton loss mechanisms may also be operating, the results indicate that charge exchange is more than sufficient as a particle loss mechanism for the storm time proton ring current decay.

Smith, P. H.↗