Search NASA⌕ Search

SEARCH · Search NASA

Results for “sample collections”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

MSR Curation Technology Development – Developing Protocols for Pre-Basic Characterization Measurements

The joint NASA/ESA Mars Sample Return (MSR) campaign could deliver to Earth the first pristine Mar-tian rock and regolith samples, collected by the Mars2020 science mission, Perseverance. In preparation for their arrival, the NASA/ESA Joint Curation Office (JCO) within the Sample Receiving Project (SRP) is developing curation technology needed to perform initial characterization of the samples while isolating samples from the Earth’s biosphere and protecting the samples from terrestrial contamination. (RSTA; Fig. 1). The Mars Sample Return Planning Group 2 (MSPG2) identified methods for achieving an array of potential science objectives for MSR outlined by the International MSR Objectives and Samples Team (iMOST) [1]. One category of methods, called Pre-Basic Characterization, recommends potential analyses that would happen before the Returnable Sample Tube Assemblies (RSTA; Figure 1) are opened: 1) Magnetometer & Magnetic Susceptibility; 2) X-ray Computed Tomography (XCT) Scanner [2]. To be in compliance with planetary protection requirements, and to limit the amount of time sample tubes are out-side of an isolated contamination-controlled environment, secondary containment is necessary. A Sample Tube Isolation Container (STIC) and Secondary Outer Containment Case (SOCC) is currently being developed at NASA JPL under the direction of the SRP JCO.

V Tu↗

Spectro-Microscopic Investigation of the Aerosol Impact on Hydrological Processes

This project investigated physico-chemical characteristics of atmospheric particles collected during DOE ARM field campaigns and how they are involved in the hydrological cycle. Our efforts were focused on multi-modal chemical imaging and molecular characterization of atmospheric particles and snow samples collected during the Surface-Atmosphere Integrated Field Laboratory (SAIL) campaign and particle samples from the Tracking Aerosol Convection Interactions ExpeRiment (TRACER) campaign.

54 ENVIRONMENTAL SCIENCES↗

The Complex Stratigraphy of the Highland Crust in the Serenitatis Region of the Moon Inferred from Mineral Fragment Chemistry

Large impact basins are natural drill holes into the Moon, and their ejecta carries unique information about the rock types and stratigraphy of the lunar crust. We have conducted an electron microprobe study of mineral fragments in the poikilitic melt breccias collected from the Taurus Mountains at the Apollo 17 landing site. These breccias are virtually unanimously agreed to be impact melt produced in the Serenitatis impact event. They contain lithic fragments and much more abundant mineral fragments of crustal origin. We have made precise microprobe analyses of minor element abundances in fragments of olivine, pyroxene, and plagioclase to provide new information on the possible source rocks and the crustal stratigraphy in the Serenitatis region. These data were also intended to elucidate the nature of the cryptic geochemical component in breccias such as these with low-K Fra Mauro basalt compositions. We chose the finest-grained (i.e., most rapidly quenched) breccias for study, to avoid reacted and partly assimilated fragments as much as possible. Most of the mineral fragments appear to have been derived from rocks that would fall into the pristine igneous Mg-suite as represented by lithic fragments in the Apollo collection, or reasonable extensions of it. Gabbroic rocks were more abundant in the target stratigraphy than is apparent from the Apollo sample collection. Some pyroxene and plagiociase, but probably not much olivine, could be derived from feldspathic granulites, which are metamorphosed polymict breccias. Some mineral fragments are from previously unknown rocks. These include highly magnesian olivines (up to Fo(sub 94)), possibly volcanic in origin, that exacerbate the difficulty in explaining highly magnesian rocks in the lunar crust. It appears that some part of the lunar interior has an mg*(= 100 x Mg/(Mg/Fe) atomic) greater than the conventional bulk Moon value of 80-84. Other volcanic rocks, including mare basalts, and rapidly- cooled impact melt rocks do not contribute significantly to the fragment population. Nor do ferroan anorthosites contribute more than a tiny part of even the plagiociase fragment population. A few mineral fragments that are consistent with the cryptic low-K Fra Mauro chemical component were found, and these appear to be from gabbroic sources. The mineral fragment populations cannot be mixed in their observed proportions to produce the whole rock composition, because the fragments are more refractory and deficient in Ti, P, and alkalis. A preferential contribution to the melt from a rock similar to sodic ferrogabbro can partly resolve the discrepancy. The population of mineral fragments requires a very diverse population of igenous rocks that are not all related to each other, demonstrating the existence of a complex crust built of numerous separate igneous plutons. Many of these plutons may have crystallized at shallow depths. The chemical composition of the melt breccias, in combination with the mineral fragment data and an understanding of the cratering process, suggests that the deepest crust sampled by the Serenitatis impace (not necessarily the deepest crust) was basaltic in composition, including KREEP and gabbroic rocks like sodic ferrogabbro, and lacking abundant olivine-rich material. These were overlain by Mg-suite rocks of varied types, including norites and troctolites that supplied most of the olivine mineral fragments. Granulities, which are metamorphosed and more feldspathic breccias, were abundant near the surface. Remote sensing indicates that the entire Serenitatis region lacks ferroan anorthosite, consistent with the results of our study.

Ryder, Graham↗

Internet of Samples

Abstract Material samples are indispensable data sources in many natural science, social science, and humanity disciplines. More and more researchers recognize that samples collected in one discipline can be of great value for another. This has motivated organizations that manage a large number of samples to make their holdings accessible to the world. Currently, multiple projects are working to connect natural history and other samples managed by individual institutions or individuals into a universe of samples that follow FAIR principles. This poster reports the progress of the US NSF‐funded iSamples project, in the context of other efforts initiated by US DOE, DiSCCo, BCoN, and GBIF. By October 2021, we will also be able to present an iSamples prototype. We encourage individual organizations that hold material samples to get to know these projects and help shape these projects to realize the goal of a global linked sample cloud that connects all material samples and is accessible to all.

Richard, Stephen M.↗

Exosomal proteome analysis of human plasma to monitor sepsis progression

Highlights: • As low as 300 μL human plasma is sufficient for exosome isolation using our one-step density gradient ultracentrifugation. • Protein profiling of septic plasma exosomes are closely related to immune responses. • SPTLC3 may play important roles in development of sepsis. Exosomes are cell-derived vesicles containing RNA, lipid, and protein, which act in body immune response, intercellular signaling and some other important biological processes. Exosomes have been extensively studied in the past several years on their disease related mechanisms and potential roles to monitor disease progression as biomarkers. Compared with analyzing exosome RNA, comprehensive proteome profiling of exosomes in clinical samples (e.g. blood) are highly demanded but limited mainly due to lack of a reproducible method for efficient exosome extraction. In this study, we evaluated and optimized an exosome preparation approach using one-step ultracentrifugation through an Optiprep™ cushion. Exosomes prepared via this method and analyzed by mass spectrometry using Q-Exactive plus, has led to reproducible identification and quantification of 200 + proteins from human plasma samples of as little as 300 μL. Therefore, such a straightforward exosome extract method has enable us to deeply profile exosome proteomes from human blood at a scale of clinical studies. As a proof of principal, we practiced this approach in analyzing the exosome proteomic profiles of blood samples collected from a sepsis patient during six time points after diagnosis. Among the 238 proteins identified and quantified across the 6 samples, protein SPTLC3 involved in the sphingolipid metabolism, shows a negative correlation (p = 0.02, correlation coefficient = −0.984) with disease progression indicated by body temperature (BD) and C-reactive protein (CRP). Therefore, SPTLC3 could be an interesting target for future study on molecular mechanism of sepsis development, as well as potential classifier to monitor clinical progression of sepsis.

60 APPLIED LIFE SCIENCES↗

Physicochemical and Molecular Insights into the Boundary Layer and Free Troposphere Aerosol Interactions over the Southern Great Plains

Ambient aerosols’ vertical profiles are critical for evaluating the role of aerosols in atmospheric chemistry and radiative transfer, but limited data on these profiles hinders our ability to fully assess their impact on the Earth's radiative balance. Here, in this study, we investigated the size-, time-, and altitude resolved composition of individual particles and bulk molecular composition of particle samples collected by an uncrewed aerial system–ArcticShark over the Southern Great Plains. Single particle microanalysis shows that, the free tropospheric (FT) samples are dominated (56-66%) by carbonaceous sulfate particles, while boundary layer (BL) samples are dominated (57-74%) by carbonaceous particles. Back trajectory simulations suggest that FT particles are likely influenced by long-range transport and have undergone aqueous-phase processing. Conversely, in-situ size distribution data shows evidence of particle growth in the upper BL and just below the FT. This observation may indicate vertical transport of particles from an elevated aerosol layer in the FT, possibly linked to a new particle formation event. This observation is further supported by high resolution molecular composition data, which reveals particle volatility increasing with increasing size, which aligns with the growth event. This study aids in fundamental understanding of the compositional and molecular specificity of vertically resolved organic aerosols to provide insights into particle size evolution for future atmospheric models.

ArcticShark↗

Investigate of atmospheric arsenic, cadmium, chromium, lead, and mercury levels in moss species found around Zilkale, by EDXRF Spectrometry

Zilkale is a castle located in Fırtına Valley and it is one of the most important historical structures in Çamlihemşin district of Rize Province in the Black Sea Region of Turkey. The castle surrounded by very high mountains that poke up into the clouds, and it rains here all year round. Tourism businesses or industrial plants are not so much there yet. In recent years, Zilkale region has begun the attract tourist, people on treaking holidays in the Kaçkar. But many domestic and foreign tourists come to this region by own car or tour buses. The aim of this study is to investigate the atmospheric concentrations of arsenic, cadmium, chromium, lead, and mercury levels in five different moss species collected around Zilkale by using Energy Dispersive X-ray Fluorescence (EDXRF) Spectrometry. The average concentrations of heavy metals in moss samples ranged from 0.79-4.63 ppm for arsenic, 54.47-143.39 ppm for chromium, 39.97-81.03 ppm for lead. The values of cadmium and mercury were found below the detection limit. This study has shown that Hypnum cupressiforme, Abietinella abietina, Rhytidium rugosum, Plagiomnium undulate, and Thuidium tamariscinum samples collected around Zilkale were used to assess the potential contamination of atmospheric As, Cd, Cr, Pb, Hg contamination in the region and made important contributions toward the understanding of atmospheric As, Cd, Cr, Pb, Hg baseline data can be used for identification of changes in the levels of these heavy metals in the studied area.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Monitoring Soil Erosion on a Burned Site in the Mojave-Great Basin Transition Zone: Final Report for the Jacob Fire Site

A historic return interval of 100 years for large fires in the U.S. southwestern deserts is being replaced by one where fires may reoccur as frequently as every 20 to 30 years. The shortened return interval, which translates to an increase in fires, has implications for management of Soil Corrective Action Units (CAUs) and Corrective Action Sites (CASs) for which the Department of Energy, National Nuclear Security Administration Nevada Field Office has responsibility. A series of studies was initiated at uncontaminated analog sites to better understand the possible impacts of erosion and transport by wind and water should contaminated soil sites burn. The first of these studies was undertaken at the Jacob Fire site approximately 12 kilometers (7.5 miles) north of Hiko, Nevada. A lightning-caused fire burned approximately 200 hectares during August 6-8, 2008. The site is representative of a transition between Mojave and Great Basin desert ecoregions on the Nevada National Security Site (NNSS), where the largest number of Soil CAUs/CASs are located. The area that burned at the Jacob Fire site was primarily a Coleogyne ramosissima (blackbrush) and Ephedra nevadensis (Mormon tea) community, also an abundant shrub assemblage in the similar transition zone on the NNSS. This report summarizes three years of measurements after the fire. Seven measurement campaigns at the Jacob Fire site were completed. Measurements were made on burned ridge (upland) and drainage sites, and on burned and unburned sites beneath and between vegetation. A Portable In-Situ Wind Erosion Lab (PI-SWERL) was used to estimate emissions of suspended particles at different wind speeds. Context for these measurements was provided through a meteorological tower that was installed at the Jacob Fire site to obtain local, relevant environmental parameters. Filter samples, collected from the exhaust of the PI-SWERL during measurements, were analyzed for chemical composition. Runoff and water erosion were quantified through a series of rainfall/runoff simulation tests in which controlled amounts of water were delivered to the soil surface in a specified amount of time. Runoff data were collected from understory and interspace soils on burned ridge and drainage areas. Runoff volume and suspended sediment in the runoff were sampled; the particle size distribution of the sediment was determined by laboratory analysis. Several land surface and soil characteristics associated with runoff were integrated by the calculation of site-specific curve numbers. Several vegetation surveys were conducted to assess post-burn recovery. Data from plots in both burned and unburned areas included species identification, counts, and location. Characterization of fire-affected area included measures at both the landscape scale and at specific sites. Although wind erosion measurements indicate that there are seasonal influences on almost all parameters measured, several trends were observed. PI-SWERL measurements indicated the potential for PM 10 windblown dust emissions was higher on areas that were burned compared to areas that were not. Among the burned areas, understory soils in drainage areas were the most emissive, and interspace soils along burned ridges were least emissive. By 34 months after the burn (MAB), at the end of the study, emissions from all burned soil sites were virtually indistinguishable from unburned levels. Like the amount of emissions, the chemical signature of the fire (indicated by the EC-Soil ratio) was elevated immediately after the fire and approached pre-burn levels by 24 MAB. Thus, the potential for wind erosion at the Jacob Fire site, as measured by the amount and type of emissions, increased significantly after the fire and returned to unburned levels by 24 MAB. The effect of fire on the potential for water erosion at the Jacob Fire site was more ambiguous. Runoff and sediment from ridge interspace soils and unburned interspace soils were similar throughout the study period. Seldom, if ever, did runoff and sediment occur in burned drainage area soils. For burned soils where runoff occurred at 1 MAB, the sediment size was finer than on unburned sites, but this effect disappeared by 3 MAB. For the three year study under the conditions tested at the Jacob Fire site, the potential for water erosion appeared relatively unaffected by the fire. Vegetation responses were documented for each year following the fire. By the end of the study, there was a substantial difference in plant densities and richness between drainage and ridge sites. Cheatgrass densities were higher in unburned plots, and cheatgrass was also more dominant in the community composition in unburned plots. Cheatgrass had increased in the burned area but so did other native species. Three years after the fire, the burned landscape continued to revegetate but had yet to approximate the condition of an unburned landscape. The results from the vegetation surveys support the wind erosion results, where the primary source of windborne particles originate from the understory, where lower plant diversity and densities were found. The soil appears to be more resilient and have a much shorter recovery time than the vegetation in this particular community.

54 ENVIRONMENTAL SCIENCES↗

Low to middle tropospheric profiles and biosphere/troposphere fluxes of acidic gases in the summertime Canadian taiga

We report features of acidic gases in the troposphere from 9 to 5000 m altitude above ground over the Canadian taiga in the summer of 1990. The measurements were conducted at a 30-m meteorological tower and from the NASA Wallops Electra aircraft as part of the joint U.S.-Canadian Arctic Boundary Layer Expedition (ABLE) 3B Northern Wetland Studies (NOWES). We sampled air for acidic gases using the mist chamber collector coupled with subsequent analysis using ion chromatography. At the tower we collected samples at two heights during a 13-day period, including diurnal studies. Using eddy flux and profile data, we estimated the biosphere/troposphere fluxes of nitric, formic, and acetic acids and sulfur dioxide. For the organic acids, emissions from the taiga in the afternoon hours and deposition during the predawn morning hours were observed. The flux intensities alone were however not high enough to explain the observed changes in mixing ratios. The measured deposition fluxes of nitric acid were high enough to have a significant influence on its mixing ratio in the boundary layer. On three days we measured vertical profiles of nitric, formic, and acetic acids through the lower to midtroposphere. We found that the chemical composition of the troposphere was extremely heterogenous. Pronounced layers of polluted air were readily apparent from our measurements. Local photochemical production and episodic long-range transport of trace components, originating from biomass burning and possibly industrial emissions, appear to have a strong influence on the composition of the troposphere and biosphere/troposphere fluxes of acidic gases at this site.

Klemm, O.↗

Dynamic Simulation Probabalistic Risk Assessment Model for an Enceladus Sample Return Mission

Enceladus, a moon of Saturn, has geyser-like jets that spray plumes of material into orbit. These jets could enable a free-flying spacecraft to collect samples and return them to Earth for study to determine if they contain the building blocks of life. The Office of Planetary Protection at NASA requires containment of any unsterilized samples and prohibits destructive impact of the spacecraft upon return to Earth, with a sample release probability of less than 1 in 1,000,000 as a recommended goal. This paper describes a probabilistic risk assessment model that uses dynamic simulation techniques to capture the physics-based, time- and state-dependent interactions between the sample return system and the environment, which drive the risk of sample release. The dynamic approach uses a Monte Carlo-style simulation to integrate the many phases and sources of risk for a sample return mission. The model is used to assess the achievability of the planetary protection reliability goal. This is accomplished by performing sensitivity studies assessing the impact of modeling assumptions to identify where uncertainties drive the risk. These results, in turn, are used to examine the feasibility of meeting key design and performance parameters that are needed to achieve the reliability goal for a given architecture with existing technologies.

Dynamic Simulation↗

Petrographic and spectral study of hydrothermal mineralization in drill core from Hawaii: A potential analog to alteration in the martian subsurface

Abstract Continuous rock core was collected for 1764 m (5786’) on the Pohakuloa Army Training base near the center of the big island of Hawaii. The core traverses basaltic lava flows from the volcano's shield-building phase, and perched aquifers and higher temperature groundwaters were encountered. The collected samples record water-rock interactions of basaltic materials in a setting that may be a model for groundwater interactions on Mars. We collected visible and infrared point spectra of materials in the lowest portion of the core, where alteration was noted to become more prominent. We identified three types of phyllosilicate spectral signatures and three types of zeolites. The phyllosilicates show similarity to those identified on Mars using data from the Compact Reconnaissance Imaging Spectrometer for Mars (CRISM). Based on the field survey, 25 depths were selected for sampling and petrographic analysis of thin sections. The spectral data and thin section work have a strong agreement in the types of materials identified by the two different techniques. Both the spectral and petrographic data indicate low to moderate temperature geothermal alteration occurred in the lower half of the core. The field spectra are a useful reconnaissance tool for selecting mineralogic diversity for subsequent higher resolution and more time-consuming laboratory analysis.

Geochemistry & Geophysics↗

Elemental Mixing State of Aerosol Particles Collected in Central Amazonia during GoAmazon2014/15

Two complementary techniques, Scanning Transmission X-ray Microscopy/Near Edge Fine Structure spectroscopy (STXM/NEXAFS) and Scanning Electron Microscopy/Energy Dispersive X-ray spectroscopy (SEM/EDX), have been quantitatively combined to characterize individual atmospheric particles. This pair of techniques was applied to particle samples at three sampling sites (ATTO, ZF2, and T3) in the Amazon basin as part of the Observations and Modeling of the Green Ocean Amazon (GoAmazon2014/5) field campaign during the dry season of 2014. The combined data was subjected to k-means clustering using mass fractions of the following elements: C, N, O, Na, Mg, P, S, Cl, K, Ca, Mn, Fe, Ni, and Zn. Cluster analysis identified 12 particle types, across different sampling sites and particle sizes. Samples from the remote Amazon Tall Tower Observatory (ATTO, also T0a) exhibited less cluster variety and fewer anthropogenic clusters than samples collected at the sites nearer to the Manaus metropolitan region, ZF2 (also T0t) or T3. Samples from the ZF2 site contained aged/anthropogenic clusters not readily explained by transport from ATTO or Manaus, possibly suggesting the effects of long range atmospheric transport or other local aerosol sources present during sampling. In addition, this data set allowed for recently established diversity parameters to be calculated. All sample periods had high mixing state indices (χ) that were >0.8. Two individual particle diversity (D i ) populations were observed, with particles <0.5 μm having a D i of ~2.4 and >0.5 μm particles having a D i of ~3.6, which likely correspond to fresh and aged aerosols respectively. The diversity parameters determined by the quantitative method presented here will serve to aid in the accurate representation of aerosol mixing state, source apportionment, and aging in both less polluted and more industrialized environments in the Amazon Basin.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The STARDUST Discovery Mission: Data from the Encounter with Comet Wild 2 and the Expected Sample Return

On January 2,2004, the STARDUST spacecraft made the closest ever flyby (236 km) of the nucleus of a comet - Comet Wild 2. During the fly by the spacecraft collected samples of dust from the coma of the comet. These samples will be returned to Earth on January 15,2006. After a brief preliminary examination to establish the nature of the returned samples, they will be made available to the general scientific community for study. In addition to its aerogel dust collector, the STARDUST spacecraft was also equipped with instruments that made in situ measurements of the comet during the flyby. These included several dust impact monitors, a mass spectrometer, and a camera. The spacecraft's communication system was also used to place dynamical constraints on the mass of the nucleus and the number of impacts the spacecraft had with large particles. The data taken by these instruments indicate that the spacecraft successfully captured coma samples. These instruments, particularly the camera, also demonstrated that Wild 2 is unlike any other object in the Solar System previously visited by a spacecraft. During my talk I will discuss the scientific goals of the STARDUST mission and provide an overview of its design and flight to date. I will then end with a description of the exciting data returned by the spacecraft during the recent encounter with Wild 2 and discuss what these data tell us about the nature of comets. It will probably come as no surprise that the encounter data raise as many (or more) new questions as they answer old ones.

Sandford, Scott A.↗

High-precision measurement of the W boson mass with the CMS experiment at the LHC

In the standard model of particle physics, the masses of the carriers of the weak interaction, the W and Z bosons, are uniquely related. Physics beyond the standard model could change this relationship through the effects of quantum loops of virtual particles, thus making it of great importance to measure these masses with the highest possible precision. Although the mass of the Z boson is known to the remarkable precision of 22 parts per million (2.0 MeV), the W boson mass is known much less precisely, given the difficulty of the measurement. A global fit to electroweak data, used to predict the W boson mass in the standard model, yields an uncertainty of 6 MeV. Reaching a comparable experimental precision would be a sensitive and fundamental test of the standard model. Furthermore, a precision measurement of the W boson mass performed by the CDF Collaboration at the Fermilab Tevatron has challenged the standard model by significantly disagreeing with the prediction of the global electroweak fit and the average of other $m_\mathrm{W}$ measurements. We report the first W boson mass measurement by the CMS Collaboration at the CERN LHC, based on a data sample collected in 2016 at the proton-proton collision energy of 13 TeV. The W boson mass is measured using a large sample of W$\toμν$ events via a highly granular binned maximum likelihood fit to the kinematic properties of the muons produced in the W$^{+}$ and W$^{-}$ boson decays. The significant in situ constraints of theoretical inputs and their corresponding uncertainties, together with an accurate determination of the experimental effects, lead to a precise W boson mass measurement, $m_\mathrm{W} =$ 80$\,$360.2 $\pm$ 9.9 MeV, in agreement with the standard model prediction.

FOS: Physical sciences↗

Area estimation using multiyear designs and partial crop identification

Statistical procedures were developed for large area assessments using both satellite and conventional data. Crop acreages, other ground cover indices, and measures of change were the principal characteristics of interest. These characteristics are capable of being estimated from samples collected possibly from several sources at varying times, with different levels of identification. Multiyear analysis techniques were extended to include partially identified samples; the best current year sampling design corresponding to a given sampling history was determined; weights reflecting the precision or confidence in each observation were identified and utilized, and the variation in estimates incorporating partially identified samples were quantified.

Sielken, R. L., Jr.↗

Preserving the Science Legacy from the Apollo Missions to the Moon

Six Apollo missions landed on the Moon from 1969-72, returning to Earth 382 kg of lunar rock, soil, and core samples-among the best documented and preserved samples on Earth that have supported a robust research program for 45 years. From mission planning through sample collection, preliminary examination, and subsequent research, strict protocols and procedures are followed for handling and allocating Apollo subsamples. Even today, 100s of samples are allocated for research each year, building on the science foundation laid down by the early Apollo sample studies and combining new data from today's instrumentation, lunar remote sensing missions and lunar meteorites. Today's research includes advances in our understanding of lunar volatiles, lunar formation and evolution, and the origin of evolved lunar lithologies. Much sample information is available to researchers at curator.jsc.nasa.gov. Decades of analyses on lunar samples are published in LPSC proceedings volumes and other peer-reviewed journals, and tabulated in lunar sample compendia entries. However, for much of the 1969-1995 period, the processing documentation, individual and consortia analyses, and unpublished results exist only in analog forms or primitive digital formats that are either inaccessible or at risk of being lost forever because critical data from early investigators remain unpublished. We have initiated several new efforts to rescue some of the early Apollo data, including unpublished analytical data. We are scanning NASA documentation that is related to the Apollo missions and sample processing, and we are collaborating with IEDA to establish a geochemical database called Moon DB. To populate this database, we are working with prominent lunar PIs to organize and transcribe years of both published and unpublished data. Other initiatives include micro-CT scanning of complex lunar samples to document their interior structure (e.g. clasts, vesicles); linking high-resolution scans of Apollo film products to samples; and new procedures for systematic high resolution photography of samples before additional processing, enabling detailed 3D reconstructions of the samples. All of these efforts will provide comprehensive access to Apollo samples and support better curation of the samples for decades to come.

Evans, Cindy↗

Leaf sample detail, Feb2016-May2016, PA-SLZ, PA-PNM, PA-BCI: Panama

This data package contains details of the date, location, species and photographs of leaf samples collected on a monthly basis from Feb to May 2016 from Parque Natural Metropolitano (PA-PNM), Barro Colorado Island (PA-BCI) and Bosque Protector San Lorenzo (PA-SLZ) in Panama. Data from BCI only available for March. This data was collected as part of the 2016 El Niño-Southern Oscillation (ENSO) campaign. Included in this data package are an Excel file with data (2016ENSO_Panama_LeafSamples) and two Excel files with associated metadata. Sample photos are included in five zip files, organized by month and site. Also included is a Word document (Metadata_description_2016_ENSO_Panama) with details such as data collection methods, equipment used, and site information. Data to be used as a reference to linking related datasets including leaf water potential, leaf spectra, LMA, gas exchange and leaf chemistry (CHN, NSC). Most leaves were sampled from sunlit canopy trees. VERSION 2 update. The identification of a species from the PNM site has been corrected as follows: the identification of the tree initially identified as Pseudosamanea guachapele (ALBIED) has been revised to Albizia adinocephala (ALBIAD). The updated data package includes revised data, metadata and protocol documents updated to reflect this change.

54 ENVIRONMENTAL SCIENCES↗

Electrical characterization and comparison of CIGS solar cells made with different structures and fabrication techniques

In a previous study, we reported on Cu(In,Ga)Se2-based (CIGS) solar cell samples collected from different research laboratories and industrial companies with the purpose of understanding the range of CIGS materials that can lead to high-quality and high-efficiency solar panels. Here, we report on electrical measurements of those same samples. Electron-beam induced current and time-resolved photoluminescence (TRPL) gave insights about the collection probability and the lifetime of carriers generated in each absorber. Capacitance and drive-level capacitance profiling revealed nonuniformity in carrier-density profiles. Admittance spectroscopy revealed small activation energies (= 0.03 eV) indicative of the inversion strength, larger activation energies (> 0.1 eV) reflective of thermal activation of absorber conductivity and a deeper defect level. Deep-level transient spectroscopy (DLTS) probed deep hole-trapping defects and showed that all samples in this study had a majority-carrier defect with activation energy between 0.3 eV and 0.9 eV. Optical-DLTS revealed deep electron-trapping defects in several of the CIGS samples. This work focused on revealing similarities and differences between high-quality CIGS solar cells made with various structures and fabrication techniques.

14 SOLAR ENERGY↗